Provision of Kitchen Cabinet in certain Sailors Md Accn and Augmentation of Parks at Officers and Sailors Md Accn area at INS Valsura, Jamnagar

Amount

Demolition of brickwork/PCC block or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of entire debris as ordered outside MoD land complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified & as directed.

Dismantling of wrought iron or mild steel work of any description and from any position not otherwise provided for in this Schedule (BOQ), complete all as specified and as directed.

Dismantling of fencing wire mesh any type and any size complete all as specified & as directed.

Excavating over areas, not exc 1.5 m deep and getting out in any type of soil complete all as specified & as directed.

Excavating in trenches, not exc 1.5 metre wide and not exc 1.5 metre in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. laying cables, pipes, etc. not exc 10 Sqm on plan & not exc 1.5m in depth and getting out in any type of soil (i.e. soft/ loose or hard/ dense soil) complete all as specified and as directed.

Returning, filling in trenches, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soil complete all as specified and directed.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface in any type of soil complete all as specified & as directed.

M&L for sand filling under floors, open pits in Park, in foundations, etc including watering and consolidation complete all as directed. Notes : (i) Approved dry sand free from vegetations, grass and other deleterious substances shall be used. (ii) For the purpose of payment, only consolidated thickness shall be measured.

Removing excavated surplus soil to a distance exceeding 1.5 km but not exc 5 km and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as directed.

M&L for broken stone or boulders hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for cutting of existing road for removing / laying UG Cables/ pipe line, depth of cutting not exceeding 120cm and width 100cm and filling the trench of road i.e. excluding top 20cm with existing aggregate obtained from cutting, watered and properly rammed to satisfaction of EIC and finally provide with & including 20 cm thick PCC 1:2:4 type B1 using 20 mm graded crushed stone aggregate to entire width of trench & finally match the top surface to road & disposal of debris to a distance not exceeding 250 metre and depositing where directed complete all as directed.

M&L for PCC 1:3:6, type C2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, roof kerbs, mud stops, coved fillets and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed.

M&L for precast RCC 1:3:6 type C1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed. Note :- Reinforcement shall be measured and paid for separately under respective item of this Schedule.

M&L for factory made pre cast cement concrete 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:4 complete all as specified & as directed.

M&L for factory made pre cast cement concrete 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) block masonry with solid blocks or slabs, 10 cm thick (with plain or interlocking joints as directed) and setting in cement mortar 1:4 in walls complete all as specified & as directed.

M&L for reinforced cement concrete 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in foundation including rafts, footings, foundation beams, plinth beams, base of columns etc., basement slabs, under-reamed piles and mass concrete, complete all as specified and as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in Walls, retaining walls, basement walls, ballast walls and the like, any thickness, above top of footings, including attached pilaster and buttresses, complete all as specified and as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) in columns, pillars, piers, posts, struts and the like complete all as specified & as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for stone/ boulders filling dry, handpacked tightly as in filter media at the back wall/ Weep holes/ drain mouths, etc and similar works, complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete complete all as specified & as directed.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc., vertical or to batter for rough finished flat surfaces of concrete complete all as specified & as directed.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc., vertical or to batter for fair finished flat surfaces of concrete complete all as specified & as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete complete all as specified & as directed.

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed.

All as per serial item No. 27 here-in-before but 6 to 10 mm dia in stirrups, spacers and binders.

S&F mild steel work as in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Grade E-165 (Fe 290), complete, all as specified & as directed.

S&F mild steel round bars 10mm dia as in tie bars fixed to fencing posts and other similar works, cut to length, bent to shape required, including cranking, bending, binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips or welding of bar at spots as directed, conforming to Grade E-165 (Fe 290), complete all as specified & as directed.

S&F mild steel screw bolts (machine made) of 5 to 10 mm diameter of neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exceeding 5 cm but not exceeding 10 cm long, complete all as specified & as directed.

S&F rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc. complete, drilled for fixing of steel sheeting or other covering. Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete conforming to Fe 290 (Gde E-165) complete all as specified and as directed.

Fixing only mild steel PVC coated chain link fencing, any mesh, size and type to any type of standards, rails, straining bolts etc. including provision of binding wire, complete all as specified & as directed. Note :- Supply only chain link fencing shall be measured and paid for separately.

Supply only mild steel PVC coated chain link fencing not less than 4mm dia of mesh wire, 100mm x 100mm mesh size (or as directed by Engineer-in-Charge) including line wire complete all as specified and as directed.

M&L for machine cut mirror polished Kota stone slab 18 to 22mm thick as in window cills, cooking platforms, wash basin counter and the like, set in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed.

M&L for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, wash basin counter and the like, set in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over & including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8, type D2 (using 40 mm graded crushed stone aggregate) as in sub-floors, sub-bases, floors and pavings, etc finished fair and even complete all as specified & as directed.

M&L for glazed ceramic coloured tiles, 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (i.e. 600mm x 300mm / 450mm x 300mm or as directed by Engineer-in-Charge), on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick back coat in CM 1:4 complete all as specified and as directed. Notes : (i) Quoted rate shall deemed to be inclusive of cement screed/ plaster. (ii) Colour of tiles shall be got approved from GE before incorporation in the work.

M&L for factory made M-35 grade, 60 mm thick machine pressed, rubber moulded precast cement concrete interlocking paver blocks of shape and size as directed with grey cement and pigment confirming to IS: 15658-2006 (ISI marked), laid over and including 50 mm thick compacted sand cushion complete all as specified and as directed. Notes : (i) Quoted rate shall deemed to be inclusive of 50 mm thick compacted sand cushioning. (ii) Shape of paver blocks shall be as approved by the GE

M&L for precast cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in Kerb block (Kerb Stone), factory casted, with plain fair faces, size 10cm x 30cm each or as directed, including weathering, slightly rounded or chamfered angle throating, with plain or interlocking joints and setting in cement mortar 1:4, fixed in position to the required line, level and curvature including making drainage opening wherever required, complete all as specified & as directed. Note : Shape & size of Kerb blocks shall be as approved by the GE.

M&L for rendering 10 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over complete all as specified & as directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of alkali resistant priming paint complete all as specified & as directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of 1st quality synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified & as directed.

M&L for two coats of 1st quality synthetic enamel paint over a coat of zinc chromate primer over any description of new steel & iron surfaces, not exceeding 10 cm in width or girth when unconnected with other painting or when painted in a different tint including necessary preparation of surfaces complete all as specified & as directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints/ solvent cement joints, laid in trenches or in floors, complete all as specifed & as directed.

M&L for PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested for 300 mm bore drain pipe complete all as specified and as directed. Note : Drain pipe shall be measured and paid for separately.

M&L for Reinforced concrete pipe 300 mm bore, Class NP2 with collars, laid to slope in trenches & jointed in cement mortar (1:1) and tested on completion, complete all as specified and as directed.

M&L for Kitchen cabinet with shutter complete in required sizes made out of 18 mm thick PVC board with one side decorative and other side white balancing lamination fixed with screws and adhesive, SS screws of 5.5 mm size, fixed as per manufacturer’s instructions and standard trade practice, complete all as specified and as directed.

All as per serial item No. 49 here-in-above, but both sides white lamination in CB shelves, partitions, sides, etc.

S&F zero crank stainless steel hinge, heavy duty, soft closing 4 holes type as in shutter of cupboards in Kitchen, complete all as specified & as directed. Make: Godrej/ Hettich/ Zuari/ Sleek/ Ebco / Arrow or equivalent make as approved by GE.

S&F stainless steel Kitchen cabinet overlay/ L clip hinges complete all as specified and as directed.

S&F 150mm long stainless steel designer handle (heavy duty) fixed to cupboard shutters with brass screws complete all as specified & as directed.

S&F Stainless steel Magnetic catcher with striking plate fixed with screws, conforming to the sample kept in GE’s office, complete all as specified and as directed.

S&F 60 cm long stainless steel telescopic channels for sliding modular Kitchen racks/ drawers complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S&F stainless steel modern plain/ cutlery basket of size 18"x20"x8" made up of surrounded by 5 mm dia and internal 3 mm dia stainless steel wire complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S&F stainless steel modern Thali basket of size 18"x20"x8" made up of surrounded by 5 mm dia and internal 3 mm dia stainless steel wire complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S&F stainless steel modern plain/ cutlery basket of size 18"x20"x6" made up of surrounded by 5 mm dia and internal 3 mm dia stainless steel wire complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S&F stainless steel modern plain/ cutlery basket of size 18"x20"x4" made up of surrounded by 5 mm dia and internal 3 mm dia stainless steel wire complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S&F stainless steel modern cup and saucer basket of size 18"x20"x4" made up of surrounded by 5 mm dia and internal 3 mm dia stainless steel wire complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S&F stainless steel modern perforated cutlery basket of size 18"x20"x4" made up of surrounded by 5 mm dia and internal 3 mm dia stainless steel wire complete all as described and as directed. Make: GODREJ / HETTICH / EBCO / ARROW or equivalent make as approved by GE.

S t modi (BID ID -3169768)

Dhangot Brothers (BID ID -3169540)

JAMNAGAR ELECTRIC AND MACHINERY CO (BID ID -3169129)