Repair to roofing, flooring, joineries and certain misc works to certain buildings of Zone B Area at Kannur under AGE (I) Cannanore.

Amount

Dismantling single layer Mangalore pattern tiles in roofing including tilting tiles all as specified and directed.

Dismantling of battens for tiles, shingles etc of any size including tilting fillets all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position unframed work all as specified and directed.

M&L for roof tile, Mangalore pattern, interlocking at side joints, laid dry all as specified and directed.

All as per item No 4 here in before but except tile all as specified and directed. Note : Serviceable tile obtained from item No 1 shall be reused.

M&L for ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement mortar (1:6) all as specified and directed.

All as per item No 6 here in before but except ridge tile all as specified and directed. Note : Serviceable ridge tile obtained from item No 1 shall be reused.

M&L for second class hard wood clean sawn batten of sectional area exc. 5 sqcm and not exc. 15 sqcm at exc. 30 cm and not exc. 35 cm centres all as specified and directed.

All as per item No 8 but except batten all as specified and directed. Note : Serviceable batten obtained from item No 2 shall be reused.

M&L for second class hard wood in scantlings clean sawn, unframed work, as in rafters, purlins etc. timber fixed all as specified and directed.

All as per item No 10 but except scantling all as specified and directed. Note : Serviceable scantling obtained from item No 3 shall be reused.

M&L for preparing surfaces of wood and wood based materials new of any description and girth not otherwise described and treated with two coats of creosote oil all as specified and directed

M&L for steel work in tubular trusses as in purlins etc including special shaped washer, etc, complete using ERW or induction butt welded tubes etc Fe 410W (Gde E-250) quality B all as specified and directed.

M&L for preparation of new or old untreated steel surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridge/valley gutter/roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

M&L for preparing surface of tiles battens, new of any size and spacing, and treated with two coats of creosote oil (measured overall on one side only spaces not deducted) all as specified and directed

M&L for preparing surfaces of old treated wood surfaces of any description and girth not otherwise described and treated with a coats of coaltar black paint all as specified and directed

Demolition of stone slab and tiles of any description and thickness in floors including cement mortar bedding (but not backing), and rubbish off the premises outside MD land and all as directed.

M&L 25mm thick PCC 1:2:4, Type B1 (using 20mm graded stone aggregate) as in flooring all as specified and directed.

M&L for coloured non-skid ceramic tiles, 7 to 8mm thick, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 20mm thick screed bed or bedding layer in cement mortar (1:6) all as specified and directed.

M&L for coloured glazed ceramic tiles 7 to 8mm thick, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm , as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

M&L for coloured glazed ceramic tiles 450x300x9mm thick, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

Demolition of brick or stone or PCC block masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exc.10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

M&L for laterite stone masonry, regular coursed, well bonded and solidly hearted , built in CM (1:6) all as specified and directed.

All as per item No 26 here in before but except laterite all as specified and directed. Note : Serviceable laterite stone obtained from item No 24 shall be reused.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 10mm thick in cement mortar (1:6) on concrete ceiling surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer all as specified and as directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash on walls surfaces all as specified and directed.

M&L for preparation of new plastered ceiling surfaces and applying three coats of white wash on walls surfaces all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) all as directed

S&F TMT bars 10 mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified and directed.

M&L for precast RCC 1:2:4, type B1, using 20 mm graded stone aggregate as in slabs set in cement mortar 1:6 including necessary form work all as specified and directed.

S&F 500 litres capacity rotational moulded polthylene water storage tanks (cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position fitted with 20mm dia PTMT float valve with polyethylene float ball including taking down unserviceable water tank all as specified in SSR Part I,2009 and directed.

S&F 1000 litres capacity rotational moulded polthylene water storage tanks (cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position fitted with 20mm dia PTMT float valve with polyethylene float ball including taking down unserviceable water tank all as specified in SSR Part I,2009 and directed.

Material & Labour for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Supply and fix sink with draining board, made out of stainless steel sheet 1mm thick with plugs, washer and waste pipe, including fixing cast iron cantilever brackets and connecting union to pipe over all size 915mm x 460mm with bowl size 410mm x330mmx160mm all as specified and directed.

Supply and fix in repairs aluminium alloy powder coated curtain rod decorative type 20mm dia fixed to wall including suitable bracket complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for removing to store of sizes upto 20mm bore all as directed.

Taking up or down steel tubing and connections including cleaning for removing to store of 25mm bore all as directed.

S&F for 15 mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F for 20 mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F for 25 mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule of 20mm bore dia all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing or concealed water tubing, etc; and making good, cutting not exc. 10cm girth in brick walls all as specified and directed.

S&F in repairs 15mm pillar taps, fancy type cast copper alloy with capstan heads, chromium plated , screwed down high pressure ,with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed.

S&F in repairs 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

Supply and fix PVC connecton 60cm long with PTMT nuts for flush tank, wash basin, etc. all as specified and directed

S&F in repairs bib tap 15mm dia, chromium plated, fancy type, cast copper alloy, screwed down, screwed for iron pipe or ferrule and complete all as directed.

S&F in repairs stop cock 15mm bore cast copper alloy, chromium plated, fancy type screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup complete all as specified and directed

S&F in repairs stop cock 20mm bore cast copper alloy, chromium plated, screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup complete all as specified and directed

S&F tubular towel rail brass, chromium plated, D type, 60cm long between flanges fixed to wall with wooden plugs with chromium plated brass screws all as specified and directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge

S&F in repairs wall mixture brass Chromium plated for mixing hot and cold water with connection to over head shower with 115 mm long bend pipe and wall flange,screwed down for iron pipe and fixed for 15 mm bore of pipe all as specified and directed by Engineer-in-Charge .Make JAQUAR Cat No FLR-5217 or equivalent

S&F in repairs, wall mixer 3-in-1 system with provision for both teliphone shower and over head shower complete with wall flange and 115 mm long bend pipe etc complete all as specified and directed by Engineer-in-Charge .Make JAQUAR Cat No CON-271 or equivalent

S&F in repairs health faucet , brass chromium plated jet spray including LDPE flexible cable with jet of 100 mm long fixing to 15 mm dia pipe all as specified and directed.

S&F CP soap dish holder of make -JAQUAR Cat part No 1131N or equivalent all as specified and directed.

S&F for in repairs towel ring round shape of Make -JAQUAR Cat part No CAN-1121N or equivalent all as specified and directed.

S&F in repairs PVC valveless, syphonic action type flushing cistern low level, 10 Litre capacity, white, with inlet, ball valve, float and handle including low or high density PVC flush pipe all as specified and directed.

S&F in repairs Vitreous China squatting pan “Orissa” pattern, of size 580 x 440 mm white, with integral foot rests, (excluding flushing cistern and flush pipe), including provision of lime concrete bedding, connection to trap and to flushing pipe, anti-syphonage pipe, etc and joint between flushing pipe and socket of WC pan, complete and making good to the floor all as specified and directed.

S&F Vitreous China Wash down water closet pan (Pedestal pattern) white, (excluding flushing cistern and flush type) pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc complete including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device as fixed in repairs all as specified and directed.

S&F in repair Vitreous China Wash basin, white, flat back, size 630 x 450 mm, including CI brackets, (but excl. pillar tap) cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed.

M&L 100 mm dia cast iron Nahani trap with grating including jointing cement concrete type B-1 (1:2:4) all as specified and directed by Engineer-ib-charge.

S & F in repairs brass chromium plated shower rose 125 mm dia suitable to 15mm bore pipe complete all as specified and as directed.

Taking down chowkats with shutters n exc. 1.5 Sqm each (without taking off shutters from the frame) all as directed.

Taking down chowkats with shutters exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) all as directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

All as per item No 72 here in before but for with transoms and mullions, with double rebated on the solid frame for fixing double shutters all as specified and directed.

S&F 3mm thick plain sheet glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane all as specified and directed.

M&L for second class hardwood panelled shutter 35mm thick (three panels) with lock rail and panel of 9mm BWP, commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F 30mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc; (with out sash bars), edges of framing, fitted with cut and mitered beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a) all as specified and directed.

S&F 35mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc; (with out sash bars), edges of framing, fitted with cut and mitered beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a) all as specified and directed.

S&F stainless steel butt hinges medium weight; 100mm size all as specified.

S&F stainless steel butt hinges medium weight; 75mm size all as specified.

S&F 100mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F 150mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 100mm size all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size all as specified.

S&F aluminium anodised sliding door bolts 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed

M&L for mild steel flat iron of size 25 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

S&F Floor door stopper Overall length of cover plate 150mm of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor etc complete all as directed.

M&L for PCC 1:2:4, type B1 using 20mm graded stone aggregate for fixing hold fast including necessary form works all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

M & L preparing new plastered surface of wall including cornices and pillasters and applying two coats of Oil emulsion distemper over a coat of alkali resistant primer all as specified and directed.

T.P.SUNIL KUMAR

VIJAY ENTERPRISES

LAKSHMI BUILDERS