REPAIR TO ROOFING, JOINERY FLOORING PLUMBING WORK SANITARY FITTINGS AND FIXTURES TO CERTAIN BLDGS AND REPAIR TO HARDSTANDING PATH RETAINING WALL PLASTERING CHAIN LINK FENCING BARBED WIRE DRAINS AND MISC WORKS AT AULI UNDER GE 871 EWS

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n exc 15 cm thickness ( below or above ground level) etc complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for etc complete all as specified and directed.

Demolition of cement concrete (reinforced) in any position of any description etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exc. 0.11 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed.

S&F Glazed ceramic tiles Coloured 350 x 250mm/450 x 350mm 7 mm thick in wall/dado etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match rendering over 10 mm thick in CM 1:4 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed.

M&L PCC 1:2:4 type B-1 (Using 20mm graded stone agg) 40 mm thick in flooring finished even & smooth with using extra cement complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in surface channel and drain complete all as specified.

M&L PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) 75 mm thick as in plinth protection complete all as specified and directed.

M&L for precast cement concrete 1:3:6 type C1 using 20mm graded aggregate as in solid building blocks, exc. 10cm in width and setting in CM (1:4) complete all as specified and directed.

- All as per item No. 10 above but except block

M&L rendering 15 mm thick in CM 1:4 mixed with WPC on brick or concrete surface finished even and smooth without using extra cement including taking down plaster complete all as specified and directed.

Supply only liquid water proofing compound as per manufacturer instructions.

Extra for forming fair finished drain and channel 30 cm inner girth in cement concrete using extra cement in forms mould mitred/stopped ends complete all as specified.

Providing precast cement concrete type B-1, 1:2:4 (20 mm graded aggregate) as in landing, cover slab (for manholes etc) chullah woods, chajjas, water trough mangers, shelves, and similar articles with plain faces complete all as specified.

M&L TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required including cranking bending spirally for hoping for col hooking ends and binding with and including mile steel wire non less than 0.9 mm dia securing with clips in quality complete all as specified.

M&L PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in coping including form work complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) pipes single socketed fixed in walls and floors or trenches etc. as in weep holes of retaining wall complete all as specified.

M&L in repair 75mm PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete including provision of lime concrete bedding complete all as specified and directed.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

S&F for PVC (SWR) 'P' trap bore of 110 mm complete all as specified and directed.

S&F for PVC (SWR) 'S' trap bore of 110 mm complete all as specified and directed.

Supply and fix in repair Vitreous china urinal, bowl type, flat back, size of 465 x 355 x 265mm (minimum), white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60cm long brass screws, pointing around urinal back in cement, with grating and union for discharge pipe and PVC waste pipe, including making all connections to existing connections, fixed complete all as specified and as directed.

S&F in repair vitreous china wash hand basin (550x400 mm) white flat back excluding taps, waste chain and plug and porcelain stopper but including brackets complete all as specified and as directed.

S&F 32 mm dia bore waste fittings brass chromium plated for glazed ware sink, basin etc with long screwed shank and fly nut , flange and bedded in red lead cement and other end fixed incl waste pipe of reqd length complete all as specified and as directed.

S&F 15 mm bore pillar tap cast copper alloy with capstan head, fancy type chromium plated screwed down high pressure with or without lettered 'Hot or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repair 15 mm bore pillar tap cast copper alloy with capstan head, fancy type chromium plated screwed down high pressure with or without lettered 'Hot or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and as directed.

Supply and fix in repair for PVC(LDPE), 32 mm dia, polyethylene, of pressure rating 6 kgf/sqcm, for wash hand basin including taking down of existing old pipe all as specified and as directed.

S&F in repair Flushing cistern low level, PVC 10 Ltr capacity symphonic action type valve, valve less with inlet ball valve, float and handle incl bracket complete all as specified and directed.

S&F in repair PVC connection 15 mm dia and 450 mm long complete all as specified and as directed.

Supply and fix in repair for 15 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 142 gms.) all as specified and as directed.

Supply and fix in repair for 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 142 gms.) all as specified and as directed.

S&F in repair of 15 mm dia CP jet with CP flexible pipe 90 cm long incl necessary fittings complete all as specified

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed

S&F in repair soap dish acrylic type complete all as specified

S&F in repair CP grating of size 100 mm dia complete all as specified

S&F in repair CP grating of size 100 mm dia with waste hole complete all as specified

Supply and fix in repair for towel Rail, brass chromium plated. 20 mm dia D type, 600 mm long between flanges complete all as specified and as directed

Supply and fix in repair for Gun metal gate valve,15mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed.

All as per item no. 41 above but 20 mm bore complete all as specified and directed

Taking up or down 15 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and directed.

All as per item no. 43 above but 20 mm bore complete all as specified and directed.

S&F 15 mm bore GI tubing medium grade with all fitting fixed to wall and ceiling or laid in floor complete all as specified and directed

All as per item no. 45 above but 20 mm bore complete all as specified and directed.

Re-fixing 15 mm bore old steel tubing and connection in new or old position (wall, ceiling, floors etc) complete all as specified and directed

Dismantling of water tank and removing to store exc 250 litre but not exc 500 litres complete all as specified and directed

Dismantling of water tank and removing to store exc 500 litre but not exc 1000 litres complete all as specified and directed

Supply and fix rotational moulded polyethylene water storage tanks ISI marked of 500 litre capacity (Cylindrical vertical with closed top) with HD polythene float (ball) and epoxy coated aluminium rod (fly nut) screwed for iron pipe or brass ferrule hoisted and fixed in position all as specified in SSR Part-I ,complete all as specified and as directed.

Supply and fix rotational moulded polyethylene water storage tanks ISI marked of 1000 litre capacity (Cylindrical vertical with closed top) with HD polythene float (ball) 15mm and epoxy coated aluminium rod (fly nut) screwed for iron pipe or brass ferrule hoisted and fixed in position all as specified in SSR Part-I ,complete all as specified and as directed.

S&F in repair Brass chromium plated shower rose 125 mm size with or without swivel joints, any size, incl fixing to steel pipe or union complete all as specified and directed

S&F in repair CP telephonic shower rose complete all as specified and directed

S&F in repair PVC over head tank cover/lid for 500ltr capacity tank complete all as specified and directed.

S&F in repair PVC over head tank cover/lid for 1000ltr capacity tank complete all as specified and directed.

Supply and fix in repair for PVC (SWR) vent cowl of 75mm bore with complete all as specified and as directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as spd and directed.

M&L for PCC 1:3:6 type C2 Concrete bed to drain pipes 100mm dia including forming cradles complete all as specified and directed.

S&F in repair for 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F in repair for 110 mm bore PVC (SWR) junction single,(Single T) equal or unequal complete all as specified and as directed.

S&F in repair for 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F in repairs 15mm dia Bib taps, cast copper alloy, chromium plated, screwed down high pressure, with crutch or butterfly handle screwed with both ends for iron pipe or for brass ferrules and complete all as specified and directed.

S&F in repairs 15mm Bib tap standard of PTMT any colour high pressure screwed for iron pipe & fixed (minimum weight 15mm-90gms)and complete all as specified and directed.

S&F in repair brass CP mixer 15 mm bore for mixing hot and cold water screwed down for iron pipe or any type of pipe and fixed in position and making good disturbed portion complete all as specified and directed.

S&F in repair for PVC water closet seat cover, black or white, closed pattern, with flat bottom and cover and mild steel chromium plated or aluminised hinging device, all as specified and as directed

S&F in repair for 15mm bore dia stop valves, cast copper alloy, screwed down , high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

Cleaning , removing all scales, dust, dirt with wire/jute brush from inside of RCC/PVC tanks of capacity exc. 250 litres and not exc. 500 litres and from mouth of connected pipes all as directed by the Engr-in-Charge

All as per item no. 67 above but exc 500 litre and not exc 1000 litre all as specified and directed.

Supply and fix in repair for toilet paper holder, Brass chromium plated, fixed to wall with chromium plated brass screws complete all as specified and as directed

S&F for brass chromium plated urinal spreader fancy type complete all as specified and directed.

S&F in repair butt hinges medium weight cold rolled mild steel of size 100 mm complete all as specified and directed.

S&F in repair butt hinges medium weight cold rolled mild steel of size 75 mm complete all as specified and directed.

S&F in repair aluminium anodised barrel tower bolt, of extruded section and fixed of 150 mm long complete all as specified and directed.

S&F in repair Mild steel barrel tower bolt stove enameled black with bright bolt and fixed of 150 mm long complete all as specified and directed.

S&F in repair for 250 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F in repair for extruded aluminium alloy handles fabricated type, anodised 150 mm long complete all as specified and directed

S&F in repair 300 mm ordinary mild steel rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

S&F in repair for door closer hydraulically regulated, designation No 3, aluminium (die cast ) body, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed including taking down old one all as specified and as directed.

S&F in repair for floor door stopper of aluminium alloy body and tongue, anodised, of 150 mm with rubber shoe and fixed in floor all as specified and directed.

S&F in repair Harrison rails, mild steel, Chromium plated with fixing brackets, stops, rollers etc complete all as specified

S&F in repair chromium plated bracket and knobs of curtain rod

S&F in repair for 0.56mm nominal dia wire galvanised mild steel wire cloth and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame incl punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed

S&F for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and as directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete precast concrete block walling complete all as specified and as directed.

Dismantling posts or struts (Wood, steel or RCC) of any section embedded in concrete, including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

Dismantling of fencing wire mesh of any type all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and as directed.

Taking down cement plaster on block masonary or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc. all as specified and as directed.

Raking out joints/ pointing in walls for random rubble or polygonal rubble uncoursed or brought up to courses masonary built in Cement or cement lime mortar complete all as specified and as directed.

M&L for PCC 1:4:8, type D-2 using 40 mm graded stone aggregate as in foundation filling or mass concrete complete all as specified and as directed.

M&L for walling of random rubble uncoarsed as well bonded bedded and solidly hearted in CM 1:6 complete all as specified and as directed.

All as per item No 92 here in before but except stone complete all as specified and as directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface nexc 20mm to face stone and dressing of face beds and joints as specified of random rubble walling, uncoursed or brought upto courses complete all as specified and as directed.

M&L for cement mortar 1:3 raised pointing to random or polygonal rubble uncoursed or brought upto courses complete all as specified and as directed

M&L for 15 mm thick rendering in cement mortar 1:4 or fair faces of brick or cement concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparing new plastered wall surfaces and applying three coats of white wash complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in foundation filling and mass concrete as in fencing post all as specified and as directed.

S&F for mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

S&F for galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. all as specified and as directed. (Note: Each line wire shall be measured)

Supply only Chain link MS galvanised fencing any size or type (The max. size of mesh does not exc 100mm x 100mm and dia of wire n.exc 3.15mm.) complete all as specified and as directed.

Fixing only Chain link fencing including line wires, any mesh, size and type to any standards, rails straining bolts, etc. including provision of binding wire complete all as specified and as directed.

S&F for mild steel round bar 10 mm dia and over mild steel round bars to be fixed as line wires etc complete all as specified and as directed.

S&F for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm long and diameter of neck between 11 to 15mm complete all as specified and directed.

S&F for mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, cooler stand ,support using Angle Iron,MS Flat Iron, tubular section etc and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described, and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed.

M&L for Prepolished Chequered cement concrete tiles 25cm x 25cm/ 30cmx30 cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments including 20 mm thick screed bed or bedding of CM 1:6 complete all as specified and as directed.

M&L for 100mm thick PCC 1:2:4 type B-1,using 20mm graded stone aggregates as in flooring finished surfaces even and smooth without using extra cement complete all as specified and directed.

M&L Extra for forming 40 cm inner girth fair finished drains or channels i.e. exc 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and as directed.

M/S Swarn Constructions