Development of new Drone Center of CAIR (Centre of AI and Robotics) at LP1 area in North Campus of IIT Mandi

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soilas per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:All kinds of soil as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :All kinds of soil Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Ploughing the existing ground to a depth of 15 cm to 25 cm and watering the same.All kinds of soil as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m.All kinds of soil as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. Complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500 D or more as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level Cement mortar 1:3 (1 cement :3 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Coursed rubble masonry (second sort) with hard stone in foundation & plinth with :Cement mortar 1:6 (1 cement : 6 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

20 mm cement plaster :1:4 (1 cement : 4 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade :Old work (one or more coats) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Finishing walls with Acrylic Smooth exterior paint of required shade :Old work (One or more coat applied @ 0.90 ltr/10 sqm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete.

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stoneof M-25 grade cement concrete in position to the required line, leveland curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge :In cement mortar as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : (copper oxidized as per IS: 1378) 125 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :125x85x5.5 mm (heavy type) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : (copper oxidized as per IS: 1378) 250x16 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / pC.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc .complete as per the architectural drawings and the directions of Engineer-in-Charge.(Cost of aluminium snap beading shall be paid in basic item): With frost glass panes of 5.00 mm thickness complete as per architectural drawings and directions of Engineer-in-charge.

Providing and fixing aluminium handles, ISI marked, powder coated (coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. 200mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing aluminium tower bolts, ISI marked, powder coated (coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.200 x 10 mm.

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

P/F dash fastner /chemical fastner for frame work as per entire satisfaction and direction of Engineer-in-charge.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall 25 mm dia nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc Internal work - Exposed on wall 15 mm dia nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing brass stop cock of approved quality :15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :25 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.75 mm diameter as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Coupler 75 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Coupler 110 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Bend 87.5° 75 mm bend as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee without door 75x75x75 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee without door 110x110x110 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee with door 75x75x75 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion Single tee with door 110x110x110 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing Nahani Trap 75mm x 110mm as per entire satisfaction and direction of Engineer -in-charge as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing Stainless steel jalli as per entire satisfaction and direction of Engineer -in-charge

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Semi rigid pipe 32 mm dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colourweighing not less than 88 gms as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in charge.

Providing and fixing toilet paper holder : C.P. brass as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittingsas per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :25 to 40 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :For pipes 100 to 250 mm diameter as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Coursed rubble masonry with hard stone (first or second sort) in superstructure above plinth level and upto floor five level.Masonry work (first sort), in cement mortar 1:6 (1 cement : 6 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Extra for coursed rubble masonry with hard stone (first or second sort) in: Square or rectangular pillars as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : Raised and cut pointing as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling / Soffit etc. complete (frame work to be paid seperatately).6 mm thick Cement fiber board as per IS: 14862 as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and laying in position plum concrete with hard stones bolders in Retaining wall etc. upto all heights and level,size and shape,etc with cement concrete with mix (1:2:4) 1 cement,2 coarse sand,4graded stone aggregrate 20mm nominal size using maximum 40% hard stone boulders in plum concrete as per direction and entire satifaction of Engineer-in-charge.(excluding the cost of centering and shuttering.) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Centering and shuttering including strutting, propping etc. and removal of form work for :Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts

Providing and fixing on wall face 110 mm diameter unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, for weep hole in retaining wall and toe wall etc. as per entire satisfaction and direction of Engineer -in-charge.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. Group B as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and drawing 3x1.5 sq mm of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed PVC conduit as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Wiring for circuit/ submain wiring alongwith earth wire with the 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Wiring for circuit/ submain wiring alongwith earth wire with the 2 X 4 sq. mm + 1 X 4 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Installation, testing and commissioning of pre-wired,fluorescent fitting / compact fluorescent fitting/LED Fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required Upto 450 mm sweep as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 6 way Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 4 way (8+12) horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing Single pole 5 to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of Single pole, in the existing MCB DB complete with connections, testing and commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 40 A rating,double pole, 240 V,, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 40 A rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 63 A rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 40 A rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 63 A rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of upto 35 sq. mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of up to 35 Sq. mm size on Cable Tray (Clamped with 1 mm thick saddle) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and making end termination with brass compression gland and aluminium lugs for 4 X 16 sq. mm (28mm) size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) as required for foundation of street light as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil, as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and installation of LED bollard in cylindrical shape of 9W with opal acrylic diffuser and IP 66 protection , CCT 5700 k etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and installation of LED Static Light Column of 4m height, 40W LED with die cast aluminium pipe housing with cylindrical opal polycarbonate diffuser designed for rugged outdoor usages and IP 65 protection , CCT 3000-5000 k etc. complete in all respect as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and installation of LED flood light lumanire of 150W and CCT 5700 K with pressure die cast housing and toughened glass and individual LED's with secondary lens optics with IP 66 ingress, 4KV inbuilt and 10kv external surge protection, efficiency 120 lm/w, etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Dismantling of LED flood light luminaire from roof top (up to 4 Meter Height) with full etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and Installation of Wall fan (400 mm ) in White Colour as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and Installation of 15W recessed mounted LED Downlight with white powder die cast housing and diffuser for low glare illumination as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and making end termination with brass compression gland and Copper lugs for 4 X 6 sq. mm size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying of 4 Core x 6 Sq. mm of 1.1 KV Copper conductor XLPE Insulated, PVC extruded inner-sheathed unarmoured, overall PVC outer-sheathed (as per IS 7098 Part 1) with latest amendments as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying of 4 Core x 16 Sq. mm of 1.1 KV Copper conductor XLPE Insulated, PVC extruded inner-sheathed, round wired armoured, overall PVC outer-sheathed (as per IS 7098 Part 1) with latest amendments as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and making end termination with brass compression gland and Copper lugs for 4 X 16 sq. mm size of PVC insulated and PVC sheathed / XLPE Copper conductor cable of 1.1 KV grade as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing of 25 x 12 mm size of medium class PVC Casing-Capping along with accessories in surface as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying of 4 Core x 16 Sq. mm of 1.1 KV Aluminium conductor XLPE Insulated, PVC extruded inner-sheathed, round wired armoured, overall PVC outer-sheathed (as per IS 7098 Part 1) with latest amendments as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and Installation of Electric Fly catcher with Two tubes Inside as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying of 10W surface and wall mounted LED batten with aluminum housing & integrated electronic driver (592 mm) with minimum colour temperature of 6000 k , P.F > 0.9 etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying of Surface mounted Downlight with Aluminium (99% Purity) Sink, available in Round shape. PC diffuser in white powder coated finish with built in electronic low THD (<10%) LED driver of wattage 15W , colour temperature 6000k and above , P.F > 0.90 etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supply of PVC Fresh Air Exhaust Fan Sweep 25 cm (250 mm) ,Air Delivery 813 m3/hr, Speed 1250 rpm, Power Input 45 W, suitable for operation on 230 V 50 Hz supply, etc as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supply, Installation, testing & commissioning of 10 Ltr. Capacity of electrical water heaters with connection pipes & top plugs etc as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying 3 core 6 Sq. mm XLPE insulated armoured copper cable 650 V/1100 V Grade as per IS7098 (Part 1) 1988 as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.