Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹43.5 LAccepted-AOC SHIVAJI NIWAS VILL CHIMBALHAR P O GEETA PEETH PALAMPUR HP 176061 | KANGRA | HIMACHAL PRADESH | 176061 | L1 | Accepted-AOC Being L1 and reasonable tender | |
| 2 | L2₹43.7 L+₹15,865 (0.36%)Rejected-Finance | L2 | Rejected-Finance Being other than L1 | |
| 3 | L3₹47.5 L+₹3.9 L (9.02%)Rejected-Finance | L3 | Rejected-Finance Being other than L1 | |
| 4 | L4₹48.9 L+₹5.3 L (12.2%)Rejected-Finance YOL CAMP TEH DHARAMSHALA DISTT KANGRA HP | YOL | KANGRA | HIMACHAL PRADESH | 176052 | L4 | Rejected-Finance Being other than L1 |
Tender Value
₹45 L
EMD Value
₹90,000
Closing Date
3 Feb 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE (KH) YOL
GE (KH) YOL, YOL CANTT, HP
Misc repair to certain bldgs at YOL CANTT under AGE BR-II of GE (KH) YOL
2023_MES_573012_1
GE/Y-57/2022-23
Open Tender
Civil Works
Item Rate
180 days
YOL CANTT
Please refer Tender documents.
9 documents required · 9 mandatory
₹500
GE (KH) YOL
₹90,000
Yes
9 Feb 2023
4 Jan 2023
6 Feb 2023
4 Jan 2023
3 Feb 2023
20 Jan 2023
Amount
SCHEDULE 'A' PART-1:- Dismantling plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof. all as specified.
Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.60mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.
Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge,hips, valley gutter and cladding to wall, fixed with self tapping screws as specified, all as specified and directed.
Taking down cement plaster on brick or stone surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc., including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.
Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on internal fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement, all as specified.
Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on external fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, mixed with WPC, all as specified. Note : Supply only Water proofing compound shall be measured and paid for seperately.
Rendering cement plaster 5mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) on ceiling, surface finished even and smooth without using extra cement, all as specified.
Supply only Liquid water proofing compound, complete all as specified.
Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer over 2mm thick wall care putty including preparation of surface complete, all as specified.
Applying material and labour for applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali and fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 Litre/ 10 sqm, over newly plastered surface, complete all as specified and directed.
Three coats of white wash on newly plastered or un plastered, previously undecorated ceiling surfaces including preparation of surfaces complete, all as specified.
Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified.
Aluminium anodized snap grid frame work of size 605 mm x 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer's catalogue/instruction), cutting holes for electrical fittings fixed on an including aluminium tee of size 25 mm x25 mm x1.5 mm as main runner, aluminium tee of size 25mmx25mmx1.25mm as cross runner and aluminium angle of size 25mmx25mmx1.25mm at the perimeter suspended from soffit at approx 900mm centre to centre with hangers 6mm dia galvanized (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanized iron flat 40mmx3mm size, 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including necessary scaffolding all as specified and directed.
Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions, complete all as specified and directed.
Preparation of new plastered surfaces of ceiling board and applying two coats of oil emulsion distemper complete all as specified and directed.
Demolition of cement concrete (unreinforced) in ground floors and paving, not exceeding 15cm thickness (below or above ground level), un-reinforced, including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.
Mat finish joint less (non skid), Premium class I grade, joint free, coloured ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.
Mat finish (non skid), Premium class I grade, joint free, coloured ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.11sqm but not exceeding 0.18 sqm, in floors and the like, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.
Dismantling floor, hearth or wall tiling including cement mortar bedding (But not backing), removing and rubbish of the premisses, complete including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.
Glazed coloured tiles of size 350x250/450x350x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.
Dismantling stone slabs and tiles of any description or thickness, laid bedded and pointed in any mortar in floors, aprons etc. including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.
Marble 18 to 20mm thick, makrana white marble, (table rubbed and polished) as in floor, steps, jambs, pillars, window cills, kitchen cooking platform /shelf and verticle surfaces duly machine cut in skirting /dado and like laid over and including 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade marble type, all as specifiedand directed.
Machine cut kota stone slab flooring 20-25 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:6 (1 cement : 6 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.
Granite (of any type) 18-20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement(1:2) with admixture of pigment to match the shade of granite stone including grinding and polishing complete as in vertical surfaces laid over and including 10mm thick rendering in cement mortar (1:4), all as specified.
Demolition Matting, single or double any type including, bamboo framing or bamboo supports, cover fillets, if any, complete all as specified and directed.
M&L PVC tiles/ sheets of thickness 1.50mm, laminated plain coloured, marbled mosaic or mottled finish, laid with approved rubber based adhesive in floors, complete all as specified and directed.
Plain cement concrete M-7.5, nominal mix, type D-2, using 40 mm graded mechanically crushed stone aggregate as in sub base, 75 mm thick, surface finished even and fair to receive top surface, all as specified.
Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all as specified.
Dismantling boarding, any description, fixed in any position with nails, complete all as specified and directed.
9mm thick 5 ply Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one side faces; fixed with screws to timber frame work, complete all as specified and directed.
18/19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, 2, 4 or 6 design and back plain fixed with screws to timber frame work as in wall panelling cup board shutters, complete all as specified and directed.
S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 40mm, all as specified.
Demolition of cement concrete (reinforced) of any description and any position not otherwise specifically provided for, complete, all as specified.
Reinforced cement concrete, M-15 (Nominal mix), type B-1, (with 20mm graded crushed stone aggregate as) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, all as specified.
TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified.
Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)in rough finished surface of concrete complete all as specified.
Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins arches, pillars complete all as specified.
Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified.
Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), all as specified.
Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified.
Dismantling timber scantlings 40 sqcm and over in section, in any position, unframed work, complete all as specified.
Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section complete all as specified.
Second class Plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads sectional area exc 13 & n. exc 25 sqcm complete all as specified.
Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.290 Gde E-165, steel work, complete, all as specified.
Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 30 cm long, diameter of neck 12 to 20mm, complete all as speciied.
Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to grade Fe.290 Gde E-165, complete, all as specified.
Rolled sections as in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240s, steel work complete, all as specified.
Mild Steel framed work as Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete, conforming to Fe 290 Gde E-165, all as specified.
Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.
Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.
Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.
Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.
Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.
Angular Stop cock with Wall Flange, cast copper alloy, fancy type chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repair, complete, all as specified.
Sink with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; ncluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm and fixed in repair, all as specified.
Stop valve, cast copper alloy, fancy, type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified.
Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified
Rotational moulded polyethylene water storage tank 1000 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding brass ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified.
15mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed in repair, complete all as specified.
Bib taps, 15mm bore, cast copper alloy with crutch or butterfly handle, fancy type chromium plated screwed for iron pipe or for brass ferrule and fixed in repair, all as specified.
Soap dish size 160x160x90mm, chromium plated, fixed to plugs with chromium plated, brass screws and fixed in repair, all as specified.
Bottle trap of bore dia of discharge pipe 32mm PTMT having minimum water seal of 25mm .(Minimum weight 32mm-260gms/ 40mm-270 gms) and fixed in repair, complete all as specified and directed.
PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with adjustable clamps of bore 110mm complete, including taking down old pipe, all as specified.
PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with adjustable clamps of bore 75mm complete, including taking down old pipe, all as specified.
PVC (SWR) bends any radius, 110mm bore with ovel access door, and jointing with solvent cement, complete all as specified.
PVC (SWR) bends any radius, 75mm bore with ovel access door, and jointing with solvent cement, complete all as specified.
PVC (SWR) junction single, (Single T) equal or unequal, Branch piece 110mm bore, provided with oval access door and jointing with solvent cement, all as specified.
PVC (SWR) junction single, (Single T) equal or unequal, Branch piece 75mm bore, provided with oval access door and jointing with solvent cement, all as specified.
PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75mm, all as specified.
Preparation of old decorated plastered or unplastered surfaces including cleaning by brooming down or with steel wire brushing scraping down smoke soot, moulded moss and efflorescent salts and cleaning oil and greasy spots and applying two coats of oil bound distemper including a coat of primer over 2mm thick wall care putty, complete, all as specified and as directed.
Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site, all as specified.
Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II
Factory made fully glazed PVC (frosted/ground/obscured) window/ventilator shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; completespecified and directed. Note:- Glass gauges inclusive of quoted rates.
Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.
Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads and fixed in repair, all as specified.
Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete, all as specified.
Sheet glass 3mm thick ordinary quality and glazing with oil putty/aluminium beads in squares, not exc. 0.5sqm in each pane, complete all as specified.
Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4 Sqm each and removing from site, all as specified.
Factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled 35mm thick shutters without interlocking rail and with one paneland panels of 9mm BWP commercial plywood or 12mm veneered particle with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, all as specified.
Factory made second class hard wood (Sal) glazed and Skelton door shutters 35mm thick open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauge etc., size of members of shutter as specified in clause 8.24 (a) of part-I, fitted to chowkats, complete all as specified.
Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 150mm, fixed, all as specified.
Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 100mm, fixed, all as specified.
Extruded aluminium alloy handles, fabricated type, anodised, of size 150mm, all as specified.
Extruded aluminium alloy handles, fabricated type, anodised, of size 100mm, all as specified.
Butt hinges, stainless steel medium weight 100mm long, all as specified.
Butt hinges, stainless steel medium weight 75mm long, all as specified.
Aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match, all as specified.
Harrison 25mm bore Curtain rails, mild steel, chromium plated with fixing brackets, stops and roller etc. fixed in repair complete all as specified.
Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.
Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads and fixed, all as specified.
Aluminium (diecast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair, complete all as specified.
300mm, ordinary rat tail rod pattern springs including roller and roller plate complete.
Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor ,overall length of cover plate 150mm, fixed in repair complete all as specified.
Natural colour 15 micron anodized aluminium door chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing door handles, tower bolts, hydraullic door closer and mortice lock, hinges, door stopper including neoprene lining. The member shall made out of extruded aluminium sections comprising of :- (a) Shutter vertical member 85.00 x 44.45 x 1.80mm weighing 1.302 Kg/RM. (b) Shutter top member 83.5 x 44.45 x 1.70 mm weighing 1.243 Kg/RM. (c) Shutter bottom member 114.30 x 44.45 x 1.29mm weighing 1.139 Kg/RM. (d) Shutter lock rail 83.5x44.45x1.70mm weighing 1.243 Kg/RM. (e) Anodised aluminium handle, fancy type, 350mm long and aluminium tower bolt of size 150mm. (f) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (g) Aluminium anodised frame of door of section 101.6 x 44.45 x 1.75mm weighing 1.367 Kg/M, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. Note:- (i) Shutter shall be fixed with heavy floor spring ISI marked and pivot, brass lock with duplicate keys.
Natural colour 15 micron anodized aluminium sliding window three track with chowkhat and aluminium grill of approved design complete all as directed with all fixing arrangements (including providing and fixing window handles, tower bolts and provision for fixing lock) including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881 Kg/RM. (b) Shutter top member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (c) Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micron anodized aluminium anodised frame of chowkhat of section 85.00 x 44.45 x 1.80 mm weighing 1.302 Kg/RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e) including 5.50mm thick tinted glass fixed with alumnium beading, silicon lining and gaskets and stainless steel wire cloth complete . (f) The size of anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and anodised aluminium tower bolt of size 100mm (02 Nos).
Natural colour 15 micron anodized aluminium window with chowkhat of approved design complete all as directed with all fixing arrangements (including providing and fixing window handles, tower bolts and provision for fixing lock) including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881 Kg/RM. (b) Shutter top member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (c) Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micron anodized aluminium anodised frame of chowkhat of section 85.00 x 44.45 x 1.80 mm weighing 1.302 Kg/RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e) including 5.50mm thick tinted glass fixed with alumnium beading, silicon lining and gaskets and stainless steel wire cloth complete . (f) The size of anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and anodised aluminium tower bolt of size 100mm (02 Nos).
Supply and fabricate and fix aluminium partition wall with top, middle and bottom frame of size 101.60x44.45x1.75mm weighing 1.367 Kg/RM, partially glazed with 5.5mm thick tinted glass with or without sash bars and partially panelled with 9mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position.
S&F 12mm thick toughened glass shutter (single leaf openable type) with diamond polished edge, clear glass including all harware fittings detailed as under, fixed in position as per manufacturer instructions including following fittings complete. (a) stainless steel top patch (Cat No. EPF-701) 01 set. (b) stainless steel top pivot (Cat No. EPF-712) 01 set. (c) stainless steel bottom patch (Cat No. EPF-702) 01 set. (d) glass to wall stainless steel lock (Cat No. FH-ECO-842) 01 set. (e) sainless steel handle 300mm size (Cat No. ESBH-011) 02 Nos for each shutter. Note:- Cat No. mention above for hardware fittings are make of ENOX, contractor may use similar type hardware fittings of make DORMA/OZONE. Make of glass ATUL/ MODI/ GURD/ SAINT GOBAIN/ JINDAL/ HINDAL/ WALCO
Hand Shower (Health Faucet) (ABS Body) with 1 Meter Long chrome finish Tube & Wall Hook and fixed in repair, complete all as specified.
Vitreous China wash down water closet rimless wall hung WC with ultra slim soft close seat cover, hinges, accessories set of size 360x490x330mm (pedestal pattern) with single piece slim concealed cistern with wall mounting frame, installation kit and s-type drain pipe connection set for wall hung WC with flush control plate kubix complete including fittings including demolition old unserviceable WC and provision of PCC M-15 type B-1 using 20mm graded stone aggregate, complete all as specified and directed.
Wash basins, vitreous china counter table top (oval shape) size 485mmx395mmx150mm, coloured, fixed in granite counter by making suitable holes, new brackets with and including cutting for and pinning on ends of brackets, 450mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythene of low or high density or PVC of 32mm dia including 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed and fixed in repair, complete all as specified and directed.
Supply and fix stainless steel towel rack 600mm long with lower hangers fixed in repair, complete all as directed by Engr-In-Charge.
Supply and fix Overhead shower 150x150mm square shape single flow (ABS body chrome plated with grey face plate) with rubit cleaning system including fixing to steel pipe or union, fixed in repair, complete all as specified and directed
Supply and fixed in repair toilet paper holder with flap recessed type (stainless steel) of vitreous china fixed to walls with chromium plated (CP) brass screws, complete all as specified and directed
stainless steel plate rack of size 90mmx750mmx250mm made of 1.00mm thick sheet and fixing over 40cm long MS angle of size 25x25x3mm- 02 Nos and fixed in repair, complete all as specified and directed.
M&L for slate tiles locally available best quality fixed on wall with neat cement slurry/paste including rendering 15mm thick cement mortar 1:4 on stone masonary/brick masonary, size and pattern as approved by Engr-In-Charge.
CP wall mixer with provn for overhead shower with 115mm long bend pipe on upper side connecting legs and wall flanges, fixed in repair, complete all as specified and directed.
Supply and fix Single lever WHB centre hole mixer chrome plated with popup waste system with 450mm long braided hoses, complete all as specified and directed.
Supply and fix of ACP board with grid including taking down existing board, complete all as specified and directed.
Stainless steel sink with double bowl, fixed in repair, complete, all as specified and directed.
Taking down carefully of existing cubicals and refixing the same, complete all as specified by Engr-In-Charge.
Water profing treatement of sunken portion/water tank padding using high solid content single component water based liquid applied elastomeric water proofing membrene as ASTMC 836 and ASTMD 6083, thickness of the memberane shall be 1.5mm, having solid content of more than 80% elongation of 500+(-) 50% laid over reinforcing layer on non woven geo-textile mesh of 40/50 50gms, including applying self primer coat by diluting with 1:1 ratio @ 0.2 kg per sqm and suface preparation including cleaning of existing treatement complete all as per specified and directed by Engineer -in -Charge.
Taking down chowkats or frames exc. 1.5 Sqm but not exc. 4 Sqm each incl iron mongry, all as specified.
Taking down chowkats or frames not exc. 1.5 Sqm each incl iron mongry, all as specified.
Taking down shutters of any description exc. 1 Sqm not exc. 2 Sqm each and removing from site, all as specified.
Taking down shutters of any description not exc. 1 Sqm each and removing from site, all as specified.
M&L for french polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats, complete all as specified and directed.
Renovation of kitchen and supply and installation of modular kitchen complete all as specified below and directed by Engr-In-Charge.
Kitchen cabinet bottom unit:- Providing and fixing of machine crafted box type cabinet bottom unit 560mm depth using 19mm boiling water proof plywood (BWP) with 0.6mm laminate the inside. The shutters will also be machine crafted with the same BWP, with 0.6mm inside laminate while on the out side it will be 0.80mm laminate or 1mm laminate of glossy finish and a machined edge band of 2mm. The hinges will be auto loaded hinges of approved make, which is of ISI marked, The shelf is to be adjustable with two slots provided at 300mm spacing so as to accomodate the shelf. The plywood should be of thickness 19mm boiling water proof (BWP) with 0.6mm laminate on top and bottom with machine cut edge band 0.5mm thick.
Kitchen overhead wall unit:- Providing and fixing of machine crafted box type over head unit 325mm depth using 19mm boiling water proof plywood (BWP) with 0.6mm laminate the inside. The shutters will also be machine crafted with the same BWP, with 0.6mm inside laminate while on the out side it will be 0.80mm laminate or 1mm laminate of glossy finish and a machined edge band of 2mm. The hinges will be auto loaded hinges of approved make, which is of ISI marked, The shelf is to be adjustable with two slots provided at 300mm spacing so as to accomodate the shelf. The plywood should be of thickness 19mm boiling water proof (BWP) with 0.6mm laminate on top and bottom with machine cut edge band 0.5mm thick.
Kitchen accessories with soft closure:-. (a) Cutlert basket 430mmx510mmx100mm (b) Cup and soucer 430mmx510mmx100mm (c) Plate (thali) 430mmx510mmx150mm (d) Plain 430mmx510mmx150mm (e) Plain 430mmx510mmx200mm (f) Degergent holder 430mmx510mmx200mm (g) Oil pullout 160mmx510mmx585mm (e) Telescopic drawer channels (f) Dustbin holder
Full height storage and loft unit:- Providing and fixing of machine crafted frame work using 19mm boiling water proof plywood (BWP) with 0.6mm laminate the inside. The shutters will also be machine crafted with the same BWP, with 0.6mm inside laminate while on the out side it will be 0.80mm laminate or 1mm laminate and a machined edge band of 2mm. The hinges will be auto loaded hinges of approved make, which is of ISI marked. The same is to be fixed in the location as directed. Note:- All measurements are to be measured as length x height. However, the depth of the boxes are to be as per the specification described above.
surinder kumar jindal & bros.
m/s Sohan singh barwal and Brothers
M/S AMOLAK SINGH AND SONS
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .