Providing Fire Fighting Medical Gas pipe line, ETP arrangements for the work of Construction of Additional Building for Additional Beds Speciality and other Amenities in Government District Head Quarters Hospital at Jayankondam in Ariyalur

Amount

Supply, Installation, Testing and Commissioning of Electrically driven Main fire pump set. Coupled end Suction fire Pump set with 60 HP Motor, 2900 rpm, 420V, 50 cycle frequency 3 phase class ‘F’ insulation, I.P. 55 protection, starting on Star Delta. The Pump shall be horizontal, end suction, top discharge. The pump shall have cast iron casing, bronze impeller, steel shaft with common base frame capable of discharging 137.0 Cu.m/hr (2280 LPM) at 70m Head. complete with base frame & foundation bolts / Anti Vibration Pads.

Supply, Installation, Testing and Commissioning of Diesel engine driven Standby Fire pump set. The engine should have RPM between 1500 to 2300. The Pump shall be horizontal end suction, top discharge mounted on common baseframe. Pump shall be directly coupled to diesel engine of suitable HP as per system design condition. Engine shall be complete with flywheel, spider coupling, Air cleaners, Water cooled,Radiator cooled,Corrosion Resistor, Oil Sump with lube at pump. Governor, Fuel Filter, starting motor battery charging alternator & instrument panel suitable for 12 volt DC including starting switches, lube oil temperature gauge,lube oil pressure & high water temperature including flexible exhaust connection.The pump shall be capable to delivery 137.0 Cu.m/hr (2280 LPM) at 70m Head. Following additional requirements shall be considered in the cost. 1) RPM of the Diesel pump to be 1500 to 2300. 2) High speed sensing to be provided and incorporated in control panel. 3) 150Ah, 12V Battery with Battery cable and stand with lock facility 4) RPM / Hour meter to be installed in separate stand to avoid failure due to vibration, not to be fixed in Engine itself. base frame & foundation bolts / Anti vibration Pads.

Supply, Installation, Testing and Commissioning of Electrically driven Jockey pump set. Monoblock end Suction fire Pump set with 10 HP Motor TEFC type, 2900 RPM 420 V, 50 cycles, 3 phase, class ‘F’ insulation, IP 55 protection, starting on DOL. The Pump shall be capable of discharging 10.8 Cu.m/Hr (180 LPM) at 70M head. complete with base frame & foundation bolts / Anti Vibration Pads.

Supply, Installation, Testing and Commissioning of Motor Control Center (Control Panel) for Electric Motor Driven pump & Diesel sets complete with incomer, DOL starter for jockey pump, Star/Delta Starter for main pump, bus bar, protective fuses, indicating lamps, volt and ammeter with interlock facility with bottom / Top entry with foot mounting type complete with all accessories.

Supply, Installation, Testing and Commissioning of Diesel Engine Control Panel for Engine Driven pump set complete with Battery Charger Unit, Pressure switch iterlock, protective fuses indicating lamps with interlock facility with bottom / Top entry with foot mounting type complete with all accessories.

Supplying, Installing, testing and commissioning of CI butterfly valves as per BS 5155 (PN 16) slim seal, Lever operated type with required flanges, nuts, bolts etc. complete.

150 NB ( Electric & Diesel) & Fire Brigade

80 NB (Jockey)

80 NB (Lever Operated for Terrace Tank connection)

Supplying, installing, testing and commissioning of C.I. Non-return valves Ball / Wafer type ( PN 16) swing type, self acting type with required flanges, nuts, bolts and gaskets etc. complete.

150 NB ( Electric & Diesel - Ball Type)

80 NB ( Jockey - Waffer Type)

Supply and Installation of C.I. Flange End Ball type Foot Valve. Flange end as per IS: 1538 (Table-IV & VI). (for Suction Side)

150 NB ( Electric & Diesel)

80 NB (Jockey)

Supply and Installation of Ball Valves for Test & Drain Purpose

200 Ltrs. Capacity Diesle tank with all required Drain, Vent, Level Indicator etc., fabricated with 4mm thick MS sheet with adequate diesel for testing

Air Cusion tank with test drain arrangements

Pressure release Valve arrangements

Pressure Switch with Needle/Ball Valves

100mm dial glycerene filled Pressure Gauge with SS Siphon tubes & Ball Valve

Automatic Air release valves

Power, Control Cabling Al. Armoured and earthing inside Fire water pump house (i.e Fire Control panel to Motors & Pr.Switches only )

Priming Tank with necessary connections like Drain, Inlet, Level Indicator, Outlet etc., Cap.500 Ltrs.

Supplying, Installing, testing and commissioning of M.S Pipes confirming to IS 1239 Pt - I Heavy Grade Class C pipes with anchor fasteners, bolts nuts, clamps, "U" bolts, Heavy Grade C Class M.S fittings such as Reducers,Tees, elbows, flanges. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports etc, as per site requirements.

Supplying, Installing, testing and commissioning of Zone control Butterfly valves as per BS 5155 (PN 16) slim seal, Lever operated type with required flanges, nuts, bolts etc. complete.

Supply and Fixing of MS/FRP Double Door Hose box to accommodate 02 nos, 15 mtrs length hose and a branch pipe / Multipurpose Nozzle, glass fronted without self stand

Supply & fixing of First Aid Hose Reel units with 20 mm dia high pressure branded rubber hoses 30.mtr.long with 19 mm dia shut-off Jet Spray nozz.le to IS:903 & Hose reel to IS:884, complete with wall mounting brackets, having 360 degree rotating & 160 degree swinging action with Isolation Ball/Gate Valve.

Stainless Steel Fire Hydrant valve with 75 mm inlet and 63 mm female intantaneous single outlet completes with Pvc cap & chain as per IS:5290,Type-A

RRL Hoses of 63 mm dia , 15 Mtrs, Long as per IS:636 with S.S coupling bearing with ISI mark

Stainless steel branch pipes 63 mm dia male intstantaneous inlet and male threaded outlet complete with hexagonal base bore nozzles as per ISI

150NB x 4 way 65NB Male Connection of 4 - Way Fire Brigade Inlet with Drain Outlet and with 150NB NRV waffer type Valve

Supply and Fixing Gun metal single ball acting air release valve with Isolation Ball valve .

Recessed Pendant Sprinklers for false ceiling areas of K-80, 1/2" BSPT threaded connection, 68 Deg.C Standard Response and Coverage

Upright Sprinklers for No false ceiling areas of K-80, 1/2" BSPT threaded connection, 68 Deg.C Standard Response and Coverage

Flexible Drops of 1 mtr. Long for Sprinkler connection above Flase ceiling (If required) at false ceiling areas

Painting of above ground pipes with one coat of red oxide primer and two coats of fire red enamel paint complete with all accessories.

Structural Support materials for pipes supports including painting with one coat of primer and 2 coats of approved enamal colour paint.

Supply & Fixing of 16-Zone Conventional Type Fire Alarm Control Panel for Fire detection & Alarm system with battery Backup and all required accessories

Conventional Type Optical Smoke detector with Base

Conventional Type Multi Smoke detector with Base

Conventional Resettable type Manual Fire Call Points

Electronic Sounders with strobe for Indoor

2C x 1.5 Sq.mm Cu. Armoured FRLS Cable for Fire Detection & Alarm System (Open cable clamping) & with all necessary accessories (Approx.)

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate)Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Gas Outlet Points: (Self sealing type - Single / DIN outlet pipe) with 'S' type bracket made up of copperand the out let of non-interchangeable for other gas.The outlet points are brazed with brass bracket withself sealing valve (Stainless Steel) with all accessories and complete set and are covered by plastic cover duly colour coated as per specific gas and button cover etc., complete as directed by the Departmental Officers and as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification.

Medical Gas Copper Pipeline arrangement to hang on the wall of socket type connection installation of seamless cleaned and degreased non arsenical phosphorous gas copper pipe line with saddles complete with brazing work including all copper fitting (tee, elbow, reducer, coupling). The copper pipelines should be tested suitable for a steam of working pressure of 17.34 kg. / cm2 (17 bar) and confirm to BS 864 Standard with specially made for brazed socket type connection. The medical gas copper pipeline should be tested as per standard and commissioning after painting as per International Code No. IS 2379/1963 Table-V. The pipelines installed at the various wings and floors etc., complete as directed by the Departmental Officers as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification..

28mm OD copper pipe 0.9mm thick

22mm OD copper pipe 0.9mm thick

15mm OD copper pipe 0.9mm thick

10mm OD copper pipe 0.9mm thick

Brass Isolation Valve suitable for the copper pipe and should be of non lubricated 90 degree turn lever ball valve of reputed make, conneced in line with medical gas pipe line system by using suitable size brass valve adopter union, ferrule, nipple, rubber "O' ring, tapion lap and etc. All pipe line regulators shall be capable of controlling pipe line pressure and must compatible with the requirements specified in IS 12827-1989. All valves should be pneumatically tested for twice the working pressure for the gas line as per IS Code 12827 / 1989 & ISO 7396 / 1987 Sepecification

28mm Isolation valve

22mm Isolation valve

15mm Isolation valve

Oxygen manifold arrangements of 2 banks x 12 cylinder each wing with semi automatic control panel which includes contact gauge 2 Nos., outlet pressure gauge, brass heavy duty IO x regulator 2 Nos. with suitable adopter, flexible SS Hose. Mainfold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 1282- 1989. Emergency alarms with illuminating display for low / high pipeline pressure and malfunctioning of system. 1) Mainfold top frame with provision for connecting 12 cylinders on right bank and 12 cylinders on left bank with high pressure interconnecting copper tubing, silver brazing, non return valve, fasteners and cylinder spport middle angle frame for claping 2 x 12 cylinders and related fasteners. The O2 manifold should with stand a pressure of 140 kg. / CM2. The installation is commissioned after testing as per standards and painted as per International Code and as directed by the Departmental Officers as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification.

Nitrous Oxide Manifold Arrangements of 2 banks x 3 cylinder each wing, with automatic control panel which includes contact gauge 2 Nos., outlet pressure gauge, brass heavy duty IOX regulator 2 Nos. with suitable adopter, flexible SS hose. Mainfold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 1282-1989. Emergency alarams with illuminating display for low / high pipeline pressure and malfunctioning of system. 1) 2 x 3 cylinder Nitrus Oxide Manifold should be suitable with stand a pressure of 140 Kg. / Cm2 and above along with high pressure copper annealed tail pipes with end brass adapter suitable for Nitrous Oxide Cylinders and manifold. 2) Top frame comprising of high pressure copper pipes of size 12mm ID 1.5mm wall thick with high pressure brass fittings made of high tensile brass and connections through non-return valves, high pressure copper tail pipes made of high pressure copper pipe size of 7mm ID x 1.5mm thick. 3) The design of middle and bottom frames should be provided to fit both round and flat bottom cylinders safely with fitted heavy duty regulator. The Manifold should be tested at 3500 pig as per IS 12827 / 1989 & ISO 7396 / 1987 Specification.

EMERGENGY NITROUS OXIDE Manifold Arrangements of 1 banks 1Cylinder each wing, with MOX 26 B regulator which includes contact gauge 2 Nos. outlet pressure gauge, brass heavy duty IOX regulator 2 Nos. with suitable adopter, flexible SS hose. Manifold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 12827 -1989. Emergency alarams with illuminating display for low / high pipe line pressure and malfunctioning of system.

Flow Meter made up of Brass with Humidifier Bottle Flow Meter should be back pressure compressed and should be accurate gas flow measurement with control range 0-13 litres per minute. It should meet strict permission and dumbling standard. The meter body should be made of brass materials. The humidifier bottle should be made of unbreakable polycorbonate material and auto cleavable at 134 degree centigrate. The rate includes flow meter and its accessories (silicon tube with mask). The cost of materials including transport, etc., complete as per standard specification and as directed by the Departmental Officer and as per IS 12827 / 1989 and ISO 7396 / 1987 Specification

Ward Vaccum Unit with Gauge both mounted on a collection jar of capacity 600 ml and with a wall bracket for mounting it on the wall. The collecion jar should be made of unbreakable polycarbonate materials which is fully auto cleavable at 134 degree centigrade as per standard specification and as directed by the Departmental Officers and as per IS 12827 / 1989 and ISO 7396 / 1987 Specification. The rate includes cost of silicon hose with SS nipple on either side.

Theatre vacuum unit:The unit should comprise of two reusable 2000ml shatter resistant bottle .Each made up of ply carbonate material and fully autoclavable at 134 degree centigrade,should have a vacuum regulator with instant ON/OFF switch and tree way left,right or both.All the above items should be mounted on a trolley having free moving castor wheels.(As per IS 12827 /19898&ISO 7396/1987

Supply, installation,testing and commissioning of equivalent to ingersoll rand reciprocating Air cooled type (10HP) rating vaccum pump as per following provisions.As per IS 12827/1987&ISO 7396/1987 specification a) Vacuum pump-10HP-1Set b) Electric Motor-10HP-1No c) DOL Starter OLR-1No d) Vacuum Switch-1No e) Vacuum gauge-1No f) Control frame with fittings-1No g) Suction Scrubber-1No h) V-Belts-1No i) G.I & M.S Fittings-1No j) Brass Fittings-1No k) Exhaust silencer-1No l) Base frame for motor and vacuum pump-1Set m) Pilot line with fittings-1Set,Vacuum Room& Air compressor room inside

Supply,installation,testing,and commissioning of MS fabricated vertical mounted type 1000 liters capacity vacuum receiver with inlet and drain holes provided suitable to operate with vacuum pump,etc., as directed by the departmental officers.

Supply, installation,testing and commissioning of compressed air system of reciprocating Oil Free Air Compressor belt driven type air compressor with following provisions. As per IS 12827/1987&ISO 7396/1987 specification. Compressor package consists of the following: a) 10 HP Air Compressor-1No b) Electric motor 10 HP -1No c)Dol Starter-L&T-10 HP-1No d) Base frame kid(for motor and compressor)-1Set e)Pressure switch-1No f)Pressure Gauge-1No g)NRV and Pilot fittings-1No h)Delivery tube-1No i)Foundation bolts&Anchor fasteners-1 No j)Belt Guard-1No k)Air Drier 50 to 60 cfm capacity-1 No.Drain ball valve-1No,Air outlet ball valve-1No, Vacuum room& Air compressor room inside Accessories: Non-return valves,Air pressure switch,pressure gauge,Isolation valves,Air filters etc., Inter connecting piping:Mild steel pipe of 2" with fittings.

Supply,installation,testing,and commissioning of MS fabricated vertical mounted type 1000 liters capacity Air receiver with inlet and drain holes provided suitable to operate with vacuum pump,etc., as directed by the departmental officers.

BED HEAD PANEL supplying and fixing of bed head panel size for 1 m length and height of 0-0.30 cm depth of 4".The Aluminium powder coated with requirment colour for provision points of O2-2 Nos,Air-1No,Vacuum-1No with double electrical socket with switch 2Nos with 2 set with 1 V-bottle holder fixing to the wall hanging including monitor stand etc complete

Design fabrication, supply and erection Bar screen 10mm square bars to suit the channel. The SS square bar should be properly epoxy coated to avoid the rusting of bars. The spacing between the square bar is 5mm So, that particles above 5mm will be retained in the entry channel and will be cleared by hand rac manually. The bar screen should be kept at an inclination of 60⁰. The bar Screen in fixed at site, inside the channel with a groove like arrangements, so that bar screen could be removed for maintenance purpose. The cost includes cost of, Ms bars, Fabrication charges, Epoxy painting charges and fixing at site transport charges to site., etc., complete.

Design, supply and erection of Neutralization or Precipitation tank for 2 m3 flow per hour with Dosing System for Oxidant dosing and suitable agitator , base frame, foundation bolts, labour charges, erection charges, transport charges precipitation tank etc., complete the rates

Design Supply, fabrication and erection of on line disinfection for effluent with Ozone in Ground Level Reactor including submersible Mixing arrangement @ the pump make is CNP / Toshio Equivalent, The capacity of the motor is 1 HP. The type of the motor is Self aspirating, non clogging with SS304 impeller , and SS 420 Shaft, suitable for 3 phase supply, 440V, 50HZ including the cost of water ozone mixing equipments with level gauge, safety valve includes the ground level reactor, motor Submersible mixing unit base frame, SS Casing,Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design, Supply of Ozone Generator with Capacity of 10 gm/ hour with oxygen Concentrator, including the cost of Ozone Generator, Oxygen Concentrator and Control Panel etc. Complete

Design, Fabrication, supply, erection of electrical panel board with necessary starters, main switches, voltmeter, ammeter, and electrical cables of required sizes from pumps to panel board as per design, The size of panel board is approximately 2 feet x 2 feet, fabricated with Ms sheets and powder coat. Necessary provisions are given in the panel board for main switch, starters, switches, voltmeter ammeter as per the design to suit Effluent Treatment plant. The cables are run from panel board to the all pumps and other electrical accessories such as level switches dosing pumps Pumps, mixing units etc complete., the cable sizes are as per the design and suitable for electrical motors fixed in the effluent treatment plant. No lighting points are considered. The cost includes the cost of panel board, starters, switches, voltmeter, ammeter, main switch, cables for motors, labour charges etc., complete.

Design Fabrication, Supply and erection of bar screen made of MS 10mm square bars to suit the channel. Inner size of channel 1000mm , wide 900mm liquid depth and 1200mm length. The MS 10mm square bars should be properly epoxy coated to avoid the rusting of bars. The spacing between the square bar is 5mm, so that the particles above 5mm will be retained in the entry channel and will be cleared by hand rac manually. The bar screen should be kept at an inclination of 60o. The bar screen is fixed at site, inside the channel with a groove like arrangements, so that bar screen could be removed for maintenance purpose. The cost includes cost of MS bars, fabrication charges, Epoxy painting charges and fixing at site transport charges to site., etc., complete.

Design Supply and erection of Tube Settler feed pump with motor with the capacity of 7.5m3 /hr as per the design. The type of the pump is horizontal, Centrifugal, Non clog, self priming coupled with base frame arrangement. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 2.0 HP. The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ .Motor make is Kirloskar/CRI/ Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, Stand by pump and motor, base frame, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design Supply and erection of Back wash pump with motor with the capacity of 5 m3 /hr , head of 3m as per the design. The type of the pump is horizontal, Centrifugal, Non clog, self priming flexible coupling drive arrangement. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 3 HP. The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ . Motor make is Kirloskar/CRI/Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, Stand by pump and motor, base frame, Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design, Fabrication, supply, erection of electrical panel board for 150 m3 Capacity stp with necessary starters, main switches, voltmeter, ammeter, and electrical cables of required sizes from pumps to panel board as per design. The size of panel board is approximately 5 feet x 3 1/2 feet, fabricated with MS sheets and powder coat. Necessary provisions are given in the panel board for bus bars, main switch , starters, switches, voltmeter ammeter as per the design to suit sewage Treatment plant motors. The cables are run from panel board to the all pumps and other electrical accessories such as level switches dosing pumps etc complete,. The cable sizes are as per the design and suitable for electrical motors fixed in the Sewage treatment Plant. No lighting points are considered. The cost includes the cost of panel board, starters, switches, voltmeter, Ammeter, main switch, cables for motors, labour charges etc., complete.

S.R.CONSTRUCTION

Shree Shivane Construction