Civil works for new store building at Milma Palakkad Dairy

Amount

Demolition of existing workshop building in Milma Palakkad Dairy completely including dismantling of tile roof, wooden rafters, purlin, doors, windows etc by means of manually/ by mechanical and stacking of the serviceable materials and disposal of unserviceable materials within in the Dairy campus as directed by Engineer in charge.

Excavation (manual / mechanical) in all types of soil for foundations of wall, columns, plinth beams, basement, raft, ducts, trenches, pits including back filling, shoring, strutting, bailing out water/pumping off water if required, removing and stacking simultaneously the excavated stuff any where within the site area complete as directed - From NGL to 1.5 m depth.

Excavation (manual / mechanical) in all types of soil for foundations of wall, columns, plinth beams, basement, raft, ducts, trenches, pits including back filling, shoring, strutting, bailing out water/pumping off water if required, removing and stacking simultaneously the excavated stuff any where within the site area complete as directed - From 1.5m to 3 m depth.

Excavation (manual / mechanical) in ordinary rock for foundations of wall, columns, plinth beams, basement, raft, ducts, trenches, pits including back filling, shoring, strutting, bailing out water/pumping off water if required, removing and stacking simultaneously the excavated stuff any where within the site area complete as directed -Up to 1.5m

Providing and laying in position cement concrete of specified grade including the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Minimum cement content to be used in this item is @ 350 kg/ cum. Excess cement used as per design mix will not be paid. All work upto plinth level.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Minimum cement content to be used in this item is @ 350 kg/ cum. Excess cement used as per design mix will not be paid. All works above plinth level.

Providing and laying in position machine batched and machine mixed design mix M-20 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Minimum cement content to be used in this item is @ 320 kg/ cum. Excess cement used as per design mix will not be paid. All work upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-20 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Minimum cement content to be used in this item is @ 320 kg/ cum. Excess cement used as per design mix will not be paid. All works above plinth level

Providing and laying in position cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) up to floor five level excluding the cost of centering, shuttering, finishing for leveling coarse of floor and roof etc.

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Centering and shuttering including strutting, etc. and removal of formwork for concrete elements in all sizes, shapes and direction including necesosry staging, scaffolding etc for all levels below ground level and upto highest plinth level. Complete

Centering and shuttering including strutting, etc. and removal of formwork for concrete elements in all sizes, shapes and direction including necesosry staging, scaffolding etc in superstructure above plinth level and upto floor V level. Complete

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete. Thermo - Mechanically Treated bars of grade Fe-500 or more

Solid block masonry using pre cast solid blocks ( factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part 1 of 1979 for foundation and plinth with thickness 20 cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

Providing and applying 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) including necessory scaffolding, staging etc complete.

1 9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges, scaffoldings etc complete

Providing and applying two coat of water thinnable cement primer of approved brand and manufacture on wall surface including necessory scaffoldings:Water thinnable cement primer

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture including scaffoldings, applying additional coats wherever required, to achieve even shade and colour.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm), scaffolidngs etc complete.

Providing and laying acid/alkali resistant vitrified floor tiles, in flooring, skirting etc (Endura) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including 3mm spacer joints and filled with epoxy tile joint filler etc., complete. (size : 300x300x15mm thk)

Providing and laying vitrified floor tiles, in flooring, skirting etc with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including 3mm spacer joints and filled with epoxy tile joint filler etc., complete.

Providing and fixing vitrified glazed tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make in all colours, shades of any size as approved by Engineer -in-Charge, in wall over tile adhesive for wall tile fixing including 3 MM spacer and joints fill with epoxy of the same brand.

Providing and fixing panelled side hung doors made of powder coated aluminium extruded architectural sections of specified size with shutter comprising of section having bottom rail of size 100mmx44.5mmx1.85 mm thick, lock rail of size 100 mm x 44.45 mm x 2 mm thick, top rails 50mm x 44.45 mm x 1.50 mm thick , vertical style 50mm x 44.45 mm x 1.80 mm thick. The top and bottom rail shall be reinforced with 8/10mm dia rods. The door shall be panelled with 6mm thick Thomoson multiwood panel at bottom and 5mm thick approved glass at top including handle, EPDM gasket, screws, fastners, lock & key, door stopper etc. as per the drawing and specifications. (Area of door opening shall be measured in sqm for payment.)

Providing and fixing powder coated fully glazed two track two paneled sliding windows made of powder coated aluminium extruded architectural sections of 27mm series frames 45x45mm and 65x27.1 mm shutter frame all having wall thickness of 1.4 ± 0.2 mm and glazing with 5mm thick approved clear/reflective type glass including necessary glazing bead of appropriate dimension, handle, lock, EPDM/Neoprene gasket, screws, fasteners etc. as per enclosed technical specifications, drawings and/or directions of Engineer in charge. The gap in between aluminium frame and adjacent rcc/brick/stone work shall be sealed by weather silicon sealant over backer rod of approved quality. (Out to out area of the window frame shall be measured in sqm for payment.)

Providing and fixing louvered ventilator made of aluminium powder coated louver profile (min 1mm thick) fixed to powder coated aluminium extruded frame of size 63.5x38.1x1mm including fastners, screws etc. complete.

Providing and fixing louvered ventilator made of 5mm thick shaded glass fixed to powder coated aluminium extruded frame of size 63.5x38.1x1mm including fastners, screws etc. complete.

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1 mm), with wall thickness 2.0mm ( ±10.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19 mm and 1 mm ( ±1 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer-in-charge Extruded section profile size 48x40 mm

24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm ( ±1 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm ( ±1 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm ( ±1 0.2 mm) wall thickness,fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ( ±1 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge( For W.C. and bathroom door shutter).

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing G.I hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge Concealed/open work, including cutting chases and making good the wall etc. 15 mm pipe 10kgf/cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed/open work, including cutting chases and making good the wall etc. 20 mm pipe 10 Kgf/ cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed/open work, including cutting chases and making good the wall etc. 25 mm pipe 10kgf /cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed/open work, including cutting chases and making good the wall etc. 32 mm pipe 10Kgf/cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. concealed/open. 40 mm pipe 10 kgf/ cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps/ clips/ at 1.00 m spacing. This includes jointing of pipes and fittings with one step PVC solvent cement and testing of jointscomplete as per direction of Engineer-in-Charge 110 mm dia 4 Kgf/cm2 - Exposed on wall/slab

Providing and fixing PVC pipes, fittings including jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

Providing and fixing PVC pipes, fittings including jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.160 mm dia 6Kgf/cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps/ clips/ at 1.00 m spacing. This includes jointing of pipes and fittings with one step PVC solvent cement and testing of jointscomplete as per direction of Engineer-in-Charge 160 mm dia 4 Kgf/cm2 - Exposed on wall/slab

Providing and fixing PVC pipes, fittings includings jointing of pipes and fittings with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. concealed/open. 50 mm pipe 6 kgf/ cm2

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 50 mm dia Vent cowl

Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

Providing and fixing UPVC ball valve of approved quality: 20mm nominal bore

Providing and fixing UPVC ball valve of approved quality: 25mm nominal bore

Providing and fixing UPVC ball valve of approved quality: 32mm nominal bore

Providing and fixing UPVC ball valve of approved quality: 40mm nominal bore

Providing and fixing CP brass angle cock conforming to IS 8931, 15mm nominal bore

Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require with intergral footrests.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 450x300 mm with single 15 mm C.P. brass pillar tap

Supply and Labour for installation of PVC Multi Inlet floor trap 110x75x50/40mm. (Supreme/Astral/ Finolex)

125x125mm CP Stainless Steel Gratings with Cockroach Protection for multi inlet floor trap.

Providing and fixing M.S plates, channels or angles of specified size and thickness welded to reinforcement steel and embedded in concrete in line and level as per the direction of Engineer in charge.

Supplying and fixing C.I. Cover with frame, C.I. gratings for chambers & man holes of specifed size, shape and weight as per the direction of Engineer in charge.

Providing and placing on terrace (at all floor levels) white colour polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Supplying approved make PVC gully trap of size 110 x 110mm and grating 150mmx150mm size and light duty C.I cover with frames 300mmx300mm size(inside) the weight of cover to be not less than 4.5kg and frame to be not less than 2.7kg (CI MH cover and frame as per IS:1726) single sealed of size conveying to size the above mentioned items and constructing 30cmx30cm internal size gully trap chamber and depth upto 60cm,115 thk brick wall in CM 1:6 on a foundation of PCC 1:4:8.100mm thick plastering inside with CM 1:3,12mm thk with a neat cement flushing coat and conveying to site,cleaning ,installing and testing approved make PVC gully trap with 110mm outlet (Fabricated), surrounding with CC 1:1.5:3, 150x150mmm,top with grating above the PVC gulley trap and light duty CI cover and frame over the chamber including cost of all materials, etc complete as per approved drawing and as directed by Engineer-in- Charge.

Supply and Labour for Installation, testing and commissioning of PVC type Manholes, valvechamber, sandtrap etc.. with suitable PCC around it with fit and finish and including excavation, back-filling,PCC, disposel, waterproofing etc upto 1 mtr depth/as per the site condition all in accordance with the drawing/ specification or relevant standards and its Cover with suitable frame and accessories 300mmx300mm (Supreme/Finolex/Astral or equivallant)

Providing and applying integral crystalline (dry shake) of hydrophilic in nature for waterproofing treatment to the RCC structures like basement raft, foundation slab, sewage & water treatment plant slab, warehouses floor, parking structures and water tank base slab etc. sprinkled @0.60kg per sqm or higher as recommended by them mnufacturer's specification over the lean concrete of above cited structures. Them aterial shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 85%, compared control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dryshake shall be capable of selfhealing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-incharge.T he product performance shall carry guarantee for 10 years against any leakage.

Providing and fixing PVC pipes, fittings including jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 200 mm dia 6 Kgf/cm2

Providing and fixing SS 304 grade Amul trap of hygienically designed main body with 8mm thick SS 304 grade top plate having 10mm slots. Inside filter shall be circular shape having 8mm dia holes and dia 150mm pipes which is having 25mm holes to filter small particles.

Constructing manholes of size 0.6x0.6m(clear inside) of depth up to 1m including excavation, 100mm thick PCC in 1:5:10,15cm foundation concrete and 15cm thick RCC wall in RCC 1:1.5:3, wall plastering CM 1:4 both inside and outside, benching and channeling with PCC 1:2:4 and finishing the channel smooth RCC top cover of 10cm thick setting and fixing CI Heavy duty manhole cover of 550 mm dia medium duty.

Constructing manholes of size 1x1m(clear inside) of depth exceeding 1m up to 2m including excavation, 100mm thick PCC in 1:5:10,15 cm foundation concrete and 20cm thick RCC wall in RCC 1:1.5:3, wall plastering CM 1:4 both inside and outside, benching and channeling with PCC 1:2:4 and finishing the channel smooth RCC top cover of 10cm thick setting and fixing CI Heavy duty manhole cover of 550 mm dia medium duty.

Anil Santhosh and Assosiates

Prathiba Developers (P) Ltd.

Muralidharan