Outsourcing and resources for operation and management of E/M installation at Ramgarh under GE (AF) Jaisalmer

Amount

Schedule 'A' Part-I General Note applicable for serial item No 2.00 of BoQ (Sch 'A' Contractors attention is hereby invited that estimated cost of serial item No 2.00 is Rs. 8,94,450.00. Quoted amount against serial item No. 2.00 is less than the amount the work (Estimated of serial item No. 2.00 of BoQ) then lowest bidder will have to deposit FDR in favour of Accepting Officer within 07 days from financial bid opened difference in Estimated cost & quoted amount of serial item No. 2.00 before evaluation of financial bid for acceptance of tender, failing which lowest tender will not be accepted. FDR submitted at the time of Acceptance of bid will be realesed only after satisfactory proof of payment of deployed person under the respective item No. 2.00 of BoQ.

Manning and Operation of 11 KV Sub Station, Ramgarh One (Skilled Electrician in each shift) in three shift of 8 Hours each for 24 Hours continuous operation in a day (including Sunday/Holiday) to maintain sub station in/out side HT Panels as specified, including daily and weekly check-up, monthly, quarterly and half yearly maintenance as per maint schedule as specified under particular specification with all minor consumable and expendable items and labour and tools for smooth and efficient operation complete all as specified and directed. Note for serial item No. 2.00 : (a) The contractor shall take over all equipment in serviceable condition at the time of commencement of contract and shall hand over in the same state at the time of completion of contract period. Any damage/loss shall be made good by the contractor at the time of completion of contract. GE's decision will be final and binding. (b) Daily cleaning of all Panels, transformers, recording meter readings. (c) Daily cleaning of all rooms viz floor, walls and ceiling fan including internal electrical fixtures. (d) No unauthorized person shall be allowed to enter in sub division. (e) 11 KV Sub Station and water supply installations will be operated 24 hours round the clock including Sunday/Holidays. (f) All T&P insulating cloths, for operators, log-books, instruction board duly laminated for 'DO or "NOT DO" Fire safety instruction board etc. shall be provided by the contractor.

Note for serial item No. 2.00 above (Contd) (g) During maintenance & operation of 11 KV Sub station, any parts found defective and require to be replaced same will be measured and paid under Schedule 'A' Part-II. (h) Contractor shall be responsible for group insurance for eleven month of manpower deployed by him against the contract. (j) Contractor shall provided proper uniform of the operator as deployed by him and dress code shall be approved by GE/AGE concerned. (k) Daily attendance register shall be maintained by both contractor and concerned JE and register weekly putup to concerned AGE for the record purpose. (l) Labour deployed by the contractor shall be responsible for complete area cleaning of 33 KV installation inside / outside all as specified and directed by Engr-in-Charge. (m) Fuel for operation of DG Sets shall be supplied by the Department as free for filling only. However storage facilities of fuel and collection of fuel from MES Store shall be provided by the contractor. (n) Daily log sheet for running hours, fuel consumption register shall be maintained by the contractor and signed by the JE /Other superintending staff employed by the contractor. (o) Daily checking of oil level, Oil pressure, priming, frequencey temperature shall carried out and records shall be maintained.

Schedule 'A' Part-II Servicing of HT, 11 KV VCB relays including calibration of IDMT relays through primary and secondary injection method and testing complete re-setting where required and ensuring proper functioning of earth fault and overcurrent relays including removing carbon deposits from contact points, spraying CRC spray and tightening fixed and moving contacts and ajdusting for smooth functioning including replacement of tripping and closing coils, 30 volt, DC and servicing solenoid switch complete all as specified and directed.

Preparation of existing old painted surface of any description such as LT Panel board, LT feeder Pillar box, LT bus bar chamber at any height and painted inside and outside (strictly existing shade) complete after scratching existing rusted surface then applying one coat of paint (superior quality smoke grey) to achieve fine finishing all around the panels and plinth including repairing of complete LT panel by welding of hinges, door and locking arrangement complete all as directed and directed.

Aluminium Bas bar suitable length duly mounted made out of aluminium with colour coded sleves (Red, Yellow and black) with necessary bus bar insulators and nut, bolts and washers of suitable size as required at site for all outgoing MCCBs including taking down old unserviceable bus bar complete all as specified and directed.

Cable jointing kit for 1100 Volts grade LT cable for straight through heat shrink type joint complete with jointing material and accessories suitable for XLPE armoured aluminium conductor cable of size 25 sqmm 3.5/4 core to 95 sqmm 3.5 core including dismantling & taking out old unserviceable jointing kit complete all as specified and directed

Cable jointing kit for 1100 Volts grade LT cable for straight through heat shrink type joint complete with jointing material and accessories suitable for XLPE armoured aluminium conductor cable of size 95 sqmm 3.5 core to 120 sqmm 3.5 core including dismantling & taking out old unserviceable jointing kit complete all as specified and directed

On Load Changeover switch 200 Amp, 4 Pole, 415 volt, 50 Hz, sheet steel enclosure with front handle to be fixed on wall with flat iron 32x6mm including thimbles, nuts, bolts, washer etc complete, including taking down old unserviceable change over switch, complete all as specified and directed.

On Load Changeover switch 315 Amp, 4 Pole, 415 volt, 50 Hz, sheet steel enclosure with front handle to be fixed on wall with flat iron 32x6mm including thimbles, nuts, bolts, washer etc complete, including taking down old unserviceable change over switch, complete all as specified and directed.

Topping up/replacement of transformer oil of transformer chamber and conservator with new transformer oil upto a required level of 50 KV di-electric strength to withstand for one minute in any type and for capacity of transformer 250 KVA complete all as specified and directed.

MCCB, 3 Pole, 100 Amps rating, rupturing capacity 16 kA, 415 Volt grade, AC, 50 Hz, thermal Magnetic protection unit and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete all as specified & directed.

MCCB, 3 Pole, 125 Amps rating, rupturing capacity 16 kA, 415 Volt grade, AC, 50 Hz, thermal Magnetic protection unit and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete all as specified & directed.

MCCB, 4 Pole, 200 Amps rating, rupturing capacity 36 kA, 415 Volt grade, AC, 50 Hz, thermal Magnetic protection unit and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete all as specified & directed.

MCCB, 4 Pole, 250 Amps rating, rupturing capacity 36 kA, 415 Volt grade, AC, 50 Hz, thermal magnetic and making connections using suitable size copper lugs/thimbles and crimping tool, including disconnecting & taking down old unserviceable MCCB, complete all as specified and directed.

MCB, SPN, 63 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 240 Volt grade, AC, 50 Hz and making connections using suitable size copper lugs/thimbles, including disconnecting & taking down old unserviceable MCB, complete all as specified & directed.

MCB, TP, 63 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 415 Volt grade, AC, 50 Hz and making connections using suitable size copper lugs/thimbles, including disconnecting & taking down old unserviceable MCB, complete all as specified & directed.

MCB, TPN, 63 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 415 Volt grade, AC, 50 Hz and making connections using suitable size copper lugs/thimbles, including disconnecting & taking down old unserviceable MCB, complete all as specified & directed.

Supply only MCB, Single Pole, 32 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 240 Volt grade, AC, 50 Hz and making connections using suitable size copper lugs/thimbles complete all as specified & directed.

Supply only MCB, SPN, 32 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 240 Volt grade, AC, 50 Hz and making connections using suitable size copper lugs/thimbles complete all as specified & directed.

Supply only MCB, TPN, 32 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 415 Volt grade, AC, 50 Hz and making connections using suitable size copper lugs/thimbles complete all as specified & directed.

Sub main wiring with 2.50 sqmm, Single Core, PVC insulated unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 volts grade conforming to IS 694 including 2.50 Sqmm Single Core PVC insulated unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 Volt grade as continuous earth wire in green colour drawn through in existing surface/ recessed steel /PVC/steel rigid conduit including taking down old unserviceable submain wiring complete all as specified. Note : Two run of 2.50 sqmm cable and one run of 2.50 sqmm cable as earth wire continuity conductor shall be measured & paid as one unit.

Sub main wiring with 4.00 sqmm, Single Core, PVC insulated unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 volts grade conforming to IS 694 including 4.00 Sqmm Single Core PVC insulated unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 Volt grade as continuous earth wire in green colour drawn through in existing surface /recessed steel/PVC/steel rigid conduit including taking down old unserviceable submain wiring complete all as specified. Note : Two run of 4.00 sqmm cable and one run of 4.00 sqmm cable as earth wire continuity conductor shall be measured & paid as one unit.

Sub main wiring with 6.00 sqmm, Single Core, PVC insulated unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 volts grade conforming to IS 694 including 6.00 Sqmm Single Core PVC insulated unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 Volt grade as continuous earth wire in green colour drawn through in existing surface /recessed steel/PVC/steel rigid conduit including taking down old unserviceable submain wiring complete all as specified. Note : Two run of 6.00 sqmm cable and one run of 6.00 sqmm cable as earth wire continuity conductor shall be measured & paid as one unit.

Surface and wall mounted LED tube light fittings of capacity 20 watt, Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver including taking down old unserviceble LED fittings complete all as specified and directed.

Surface and wall mounted LED tube light fittings of capacity 9 watt, basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver including taking down old unserviceble LED fittings complete all as specified and directed.

Surface and wall mounted 10 watt LED bulk head fitting in engineering plastic housing with clear prismatic diffuser complete with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 including taking down old unserviceble LED fittings complete all as specified and directed.

Ultra modern designed architectural, LED Recessed full open 2X2 Tile, Glare free uniform illumination with longer life and less maintenance, luminaire of capacity 36 watt which provides soft-light and suitable for armstrong/grid ceiling including taking down old unserviceable LED light fittings complete all as specified and directed.

Sheet metal enclosure powder coated single phase DB TPN 4 ways and neutral 415 Volts, AC, 50 Hz, with 200 Amps rated bus bar Double Door (IP-43) suitable for fixing of MCBs including fixing of lugs in main incomming and outgoing line and fixing of cable glands of suitable size including grouting flush in the wall by means of nuts, bolts, angle iron and making good disturbed surfaces including taking down old unserviceable complete all as specified and directed.

Sheet metal enclosure powder coated single phase DB SPN 4 ways and neutral 240 Volts, AC, 50 Hz, with 200 Amps rated bus bar Single Door (IP-43) suitable for fixing of MCBs including fixing of lugs in main incomming and outgoing line and fixing of cable glands of suitable size including grouting flush in the wall by means of nuts, bolts, angle iron and making good disturbed surfaces including taking down old unserviceable complete all as specified and directed.

Sheet metal enclosure powder coated single phase DB SPN 8 ways and neutral 240 Volts, AC, 50 Hz, with 200 Amps rated bus bar Single Door (IP-43) suitable for fixing of MCBs including fixing of lugs in main incomming and outgoing line and fixing of cable glands of suitable size including grouting flush in the wall by means of nuts, bolts, angle iron and making good disturbed surfaces including taking down old unserviceable complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No. 3 of SSR Part-I and connection to main switch board/Test point/ panel/ equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exceeding 50 metre, charcoal and salt in alternate layer 15cm thick all around the earth plate electrode, Mild Steel Funnel with wire mesh, 20mm bore, GI pipe medium grade, 1.50 metre long for watering and 15mm bore, GI pipe light grade, 7.50 metre long for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:2:4) type B-1, using 20mm graded stone aggregate with angle iron 40x40x5mm frame 60mm thick RCC cover with 6mm steel bars 100mm centre to centre both ways etc including dismantling & taking out old existing unserviceable earthing complete all as specified & as directed. Note : (i) PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) If earth resistance of earthing is not found satisfactory it will be redone by the contractor on his risk and cost.

Point wiring for one light point controlled by one way switch with 1.50 sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 Volt grade including 1.50 sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS, terminated & including suitable size module boxes for housing of modular switches, sockets, regulators including taking down old unserviceable point wiring complete all as specified & directed. Note: (i) Unit rates quoted by contractor shall be deemed to included for cutting chases in walls, ceilings and making good surfaces in cement and sand mortar (1:3) and finishing the surfaces to match with existing surfaces. (Make : Hylem/Anchor/Formica including machine screws and washer etc for fixing switches sockets etc including 1.5 sqmm copper conductor, standard (green colour earth), PVC insulated unsheathed earth wire to commen earth and connected to earth dolly as specified and directed.

Point wiring for one light point controlled by one way switch with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS, terminated & including suitable size module boxes for housing of modular switches, sockets, regulators including taking down old unserviceable point wiring complete all as specified and directed. Note : (i) Unit rates quoted by contractor shall be deemed to included for cutting chases in walls, ceilings and making good surfaces in cement and sand mortar (1:3) and finishing the surfaces to match with existing surfaces. (Make : Hylem/Anchor/Formica including machine screws and washer etc for fixing switches sockets etc including 1.5 sqmm copper conductor, standard (green colour earth), PVC insulated unsheathed earth wire to commen earth and connected to earth dolly as specified and directed.

All as per serial item No. 32.00 here-in-before but for one fan point controlled by one switch and regulator.

All as per serial item No. 32.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5/6 Amp switch on same board.

All as per serial item No. 32.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5/6 Amp switch on independent board.

All as per serial item No. 32.00 here-in-before but for one bell/ buzzer point controlled by one bell push.

Switch piano, flush type, Single Pole, one way, 6 Amp, 240 Volts (ISI Marked) in repair complete all as specified and directed.

Switch piano, flush type, Single Pole, one way, 15/16 Amp, 240 Volts (ISI Marked) in repair complete all as specified and directed.

Switch piano, flush type, Single Pole, two way, 5/6 Amp, 240 volt (ISI Marked) in repair complete all as specified and directed.

Bell push, flush type, Single Pole, 5/6 Amp, 240 volt (ISI Marked) in repair complete all as specified and directed.

Bell Multi Music Type, AC supply, Single Pole, 240 volt (ISI Marked) in repair complete all as specified and directed.

Socket outlet 2 in 1, 5 pin, 15/16 Amps, flush type, 240 Volts (ISI Marked) in repair complete all as specified and directed.

Socket outlet, 2 in 1, 3 pin, 5/6 Amp, flush type, 240 Volts (ISI Marked) in repair complete all as specified and directed.

Ceiling rose surface bakelite with two or three terminal PVC/Polycarbonate, isolated body (ISI Marked), 240 volts in repair complete all as specified and directed.

Lamp holder, PVC / Polycarbonate type (angle/batten) with back plate suitable for batten fittings in repair complete all as specified and directed.

Dismantling/taking down old unserviceable electrical fiitting fixture and day to day complaint of electrical like bulb, switchs, Fan, socket, tube light, Plug top, MCBs, LED light, Bulb head light etc replace/repairs including minor repair/loose connection and testing complete with replace the following item/part complete all as specified and directed.

Supply only switch piano, flush type, Single Pole, one way, 6 Amp, 240 Volts (ISI Marked) complete all as specified and directed.

Supply only switch piano, flush type, Single Pole, one way, 15/16 Amp, 240 Volts (ISI Marked) in repair complete all as specified and directed.

Supply only socket outlet 2 in 1, 5 pin, 15/16 Amps, flush type, 240 Volts (ISI Marked) complete all as specified and directed.

Supply only socket outlet, 2 in 1, 5 pin, 5/6 Amp, flush type, 240 Volts (ISI Marked) complete all as specified and directed.

Supply only Plug top, 3 Pin, 5/6 Amp, 240 Volts (ISI Marked) complete all as specified and directed.

Supply only Plug top, 3 Pin, 15/16 Amp, 240 Volts (ISI Marked) complete all as specified and directed.

Supply only stepped type electronic fan regulator, flush type and connecting up, 100 watt, 240 volt (ISI marked) complete all as specified and directed.

Supply only LED Adore 10 watt base capacity B22, STAR Lamp lumen output 950, color temp 6500K complete all as specified and directed.

Supply only LED Adore 15 watt base capacity B22, STAR ball Lamp lumen output 1425, color temp 6500K complete all as specified and directed.

Supply only Lamp holder, PVC / Polycarbonate type (angle/batten) with back plate suitable for batten fittings in repair complete all as specified and directed.

Supply only PVC rectangular block for flush mounting box switches/socket with 3mm thick plastic sheet cover of size 200mm x 150mm x 50mm complete all as specified and directed.

Supply only PVC rectangular block for flush mounting box switches/socket with 3mm thick plastic sheet cover of size 100mm x 100mm x 50mm complete all as specified and directed.

Supply only PVC rectangular block for flush mounting box switches/socket with 3mm thick plastic sheet cover of size 100mm x 100mm x 50mm complete all as specified and directed.

Supply only 1.50 Sqmm, 90 metre roll, Single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 volt grade conforming to IS 694 complete all as specified and directed.

Supply only 2.50 Sqmm, 90 metre roll, Single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 volt grade conforming to IS 694 complete all as specified and directed.

Supply only 4.00 Sqmm, 90 metre roll, Single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 volt grade conforming to IS 694 complete all as specified and directed.

Supply only starting capacitor 2.50 MFD suitable for Air Conditioner/Ceiling Fan/Exaust Fan complete all as specified and directed.

Rewinding of ceiling Fan, 1200mm sweep, 240 volts, 50 Hz, AC supply including removal of existing burnt winding wire carefully from the slots, propper cleaning the slots thoroughly with necessary cleaning agent, applying slot insulation and rewinding the same with super enmelled copper winding wire of same gauge, same weight and same number of turns as that of existing and connecting the coils suitable to operate, capacitor type, tying the windings and applying air dry insulating varnish and drying the windings including replacing the defective components such as bearing, gun metal bush, rubber bush/bolt, capacitor, flexible cord, shaft and painting including assembling after lubricating movable components complete and testing including taking down and fixing the same position after repairing of ceiling fan complete all as specified and directed.

Rewinding of Exhaust Fan, 300mm sweep, 240 volts, Singple Phase, 50 Hz, AC supply including removal of existing burnt winding wire carefully from the slots, propper cleaning the slots thoroughly with necessary cleaning agent, applying slot insulation and rewinding the same with super enmelled copper winding wire of same gauge, same weight and same number of turns as that of existing and connecting the coils suitable to operate, capacitor type, tying the windings and applying air dry insulating varnish and drying the windings including replacing the defective components such as bearing, gun metal bush, rubber bush/bolt, capacitor, flexible cord, shaft and painting including assembling after lubricating movable components complete and testing including taking down and fixing the same position after repairing of exhaust fan complete all as specified and directed.

Rewinding of Exhaust Fan, 450mm sweep, 240 volts, Singple Phase, 50 Hz, AC supply including removal of existing burnt winding wire carefully from the slots, propper cleaning the slots thoroughly with necessary cleaning agent, applying slot insulation and rewinding the same with super enmelled copper winding wire of same gauge, same weight and same number of turns as that of existing and connecting the coils suitable to operate, capacitor type, tying the windings and applying air dry insulating varnish and drying the windings including replacing the defective components such as bearing, gun metal bush, rubber bush/bolt, capacitor, flexible cord, shaft and painting including assembling after lubricating movable components complete and testing including taking down and fixing the same position after repairing of exhaust fan complete all as specified and directed.

PVC canopy suitable for 1200mm sweep complete all as specified and directed.

MS clamp with mild steel nuts, bolt, quarter pin complete suitable for 1200mm sweep complete all as specified and directed.

Down rod 600mm long for ceiling fan complete all as specified and directed.

Ball bearing suitable size for exhaust fan of any sweep complete all as specified and directed.

Painting and numbering of ceiling fan complete by using synthetic enamel paint by spraying including filling cavity with filler and applying one coat of synthetic enamel paint after proper cleaning/craping etc., complete all as specified and directed

JAI ENGINEERING COMPANY

SS SODHA ENTERPRISES

M/s Shree Construction Company

shiv construction & Engineers

M/S SHRI HARI CONSTRUCTION COMPANY

M/S AUTOMATION AND SWITCHGEAR CONTROL

S.D. And Company