REPAIR TO TOILETS BATH SUNKEN PORTION SANITARY PLUMBING IN MD ACCN IN ZONE-A AT DEFENCE LAB JODHPUR

Amount

Demolition of floor, hearth or wall tiling including cement mortar bedding or backing coat, removing rubbish off the premises, removal and depositing where directed and leaving the more clean of any plastering complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete unreinforced in ground floors, kota stone, granite flooring, tiles flooring and pavings not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer in charge.

M&L glazed ceramic coloured tiles of size 350 x 250mm x 7mm /450mmx350mmx7mm/450mmx300mmx 7mm thick on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick backing coat in CM (1:4) complete all as specified and directed by Engineer-in-charge.

M&L non-skid ceramic coloured tiles of 7 to 8mm thick, (square / rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15 mm thick in CM (1:6) complete all as specified and directed by Engineer-in-charge.

M&L Water proofing treatment to RCC sunken slab of toilet as under firstly demolish all PCC and flooring of sunken portion of toilt portion ,cleaning the surface with steel wire brush / coil bresh and remove all loose particle of concrete and provide 15 mm plaster in CM 1:3 with water proofing compound on vertical surface of sunken portion, creating fillet covering of 50x50 mm with polymer modified mortar on the junction of slab and wall after apply first coat of two component modified polymer coating on horizontal and vertical surface and laid glass fibre mesh immediately above coating apply second coat of two component modified polymer coating after 72 hrs and fillng sunken portion with PCC 1:4:8 type D-2 to required level jointing the sanitary pipes with the water proofing tape having bridging ability of more than 1.50 mm ,filling the gap between wall and sanitory pipe with non shrink cementious grout complete treatment shell be carried out by authorised applicator of water proofing manufacturer like Dr Fixit/ Fosroc /BASF /STP etc Note:-The plan area of floor shall be considered for payment and WPC shall be measured and paid separately.

Supply only integral water proofing compound (ISI marked) all as specified & directed by Engineer-in-charge.

Taking down cement or cement lime plaster, any description on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed by Engineer-in-charge.

M&L 15 mm thick , plaster in cement mortar (1:4) on stone masonry wall surfaces or surfaces other than fair faces of brick work or one side of lathing and finishing the surface even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L rendering 10 mm thick plaster in cement mortar (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frames not exceeding 1.5 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-charge.

S&F solid PVC door frame of size 50 x 47mm made out of 5mm plain colour PVC sheet re-inforced with M.S. square tube supplying and fixing in opening as per specification and drawing in SSR Part II, complete all as specified and directed by Engineer-in-charge.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strips of 20mm width stuck inside with solvent cement for tiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed the stiles and rails with suitable PVC Sheet beading and jointed together with solvent cement supplying and fixing in the frame at site all as per specification and drawing in SSR Part-II , complete all as specified and directed by Engineer-in-charge.

S&F 100mm size,PTMT butt hinges with steel screws complete all as specified and directed by Engineer-in-charge.

S&F 150 mm size PTMT barrel tower bolts with steel screws complete all as specified and directed by Engineer-in-charge.

S&F 150mm size PTMT door handles with steel screws complete all as specified and directed by Engineer-in-charge.

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-charge.

Taking up or down 20mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-charge.

S&F GI tubing (ISI marked) 15mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors (concealed tubing) complete all as specified and directed by Engineer-in-charge.

S&F GI tubing (ISI marked) 20mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors (concealed tubing) complete all as specified and directed by Engineer-in-charge.

Fixing only GI tubing (ISI marked) 15 mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors (concealed tubing) obtained from taking down complete all as specified and directed by Engineer-in-charge.

Fixing only GI tubing (ISI marked) 20 mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors (concealed tubing) obtained from taking down complete all as specified and directed by Engineer-in-charge.

S&F in repairs vitreous china squatting pan "Orissa" pattern, size 580 x 440mm white, with integral foot rest (Excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe,lime/cement concretebedding and making good to the floor complete all as specified and directed by Engineer-in-charge.

S&F in repair vitreous china wash down water closet pan/ padestal(EWC) including plastic water closet seat,black,closed pattern with flat bottom,and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engineer-in-charge.

S&F in repairs 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, complete all as specified and directed byEngineer-in-charge.

S&F in repair vitreous china wash basin white, flat back of size 550 x 400 mm white including waste fittings, brass chromium plated , coupling,pvc waste pipe32 mm size, brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe complete all as specified & directed by Engineer-in-charge.

M&L 75 mm size cast iron floor, trap, with grating including jointing to waste pipe fixed in cement conrete (1:2:4) type B-1 including taking down old un-serviceable floor trap complete all as specified & directed by Engineer-in-charge.

S&F in repairs CP grating for Nahani trap/ floor trap of size 100/75 mm bore complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC connections 450 mm long, 15mm size with PTMT nuts for WHB, flushing cistern, geysers etc complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC connections 600 mm long, 15mm size with PTMT nuts for WHB, flushing cistern, geysers etc complete all as specified & directed by Engineer-in-charge.

S&F, in repair, 32 mm dia, 600/750 mm long PVC waste pipe for wash basin, sink etc complete all as specified & directed by Engineer-in-charge.

S&F in repairs, brass chromium plated, fancy type, bib taps, with crutch or butter fly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

S&F in repairs stop cock, fancy type, chromium plated, with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15 mm bore iron pipe or for union complete all as specified & directed by Engineer-in-charge.

S&F in repairs pillar taps, cast copper alloy, with half turn handle type, chromium plated, screwed down high pressure, with or without lettered 'Hot' & 'Cold' with long screwed shanks and fly nuts, screwed for 15 mm bore iron pipe complete all as specified & directed by Engineer in charge.

S&F in repair fancy type, chromium plated brass wall mixer with over head shower screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

S&F in repairs Brass CP wash Basen Mixer for mixing hot & cold water with capstan head screwed, down for iron pipe of 15mm bore complete all as specified & directed by Engineer-in-chage.

S&F in repairs sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes: including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified & directed by Engineer-in-charge.

Dismantling of old unserviceable PVC water tank of 1000 Ltrs capacity complete all as specified and directed by Engineer-in-charge.

S&F 1000 ltrs capacity rotational moulded polythene water storage tanks white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I including PTMT ball valve heigh pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms complete all as specified and directed by Engineer-in-charge.

S&F in repairs, 110mm bore PVC (SWR) single socketed in any length with rubber ring joints & fixed to walls complete all as specified and directed by Engineer-in-charge.

S&F in repairs, 110 mm bore (SWR) PVC bends any radius complete as specified and directed by Engineer-in-Charge.

Dismantling cast iron work of any description and in any position complete all as specified & directed by Engineer-in-charge.

Dismantling of 100mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar/lead joint and taking out of trenches if required /walls including fittings, complete all as specified & directed by Engineer-in-charge.

S&F 100 mm bore cast iron P or S trap complete all as specified & directed by Engineer-in-charge.

S&F 100 mm bore CI branch piece, single, (equal or unequal) ordinary or inverted (spigot or socket type) or with paralled branches with ovel access door including jointing in CM (1:1) complete all as specified & directed by Engineer-in-charge.

S&F, in repairs 100mm dia, cast iron nahani trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate all as specified and directed by Engineer-in-charge.

S&F 100 mm bore cast iron bends, (any radius) with duck's foot or heel rest complete all as specified & directed by Engineer-in-charge.

S&F 100mm bore (sand cast pipe) soil, waste and vent pipes in any length with or without ears and jointing with lead & fixed to walls complete all as specified & directed by Engineer-in-charge. Note:-lead joint will be measured and paid saperately

S&F 100mm bore (sand cast pipe) soil, waste and vent pipes in any length with or without ears and jointing with lead & laid in trenches or in floors complete all as specified & directed by Engineer-in-charge. Note:-lead joint will be measured and paid saperately

S&F 100mm bore cast iron cowl (sand cast) complete all as specified & directed by Engineer-in-charge.

M&L Lead joints for 100 mm bore cast iron (sand cast pipe) and fittings complete all as specified & directed by Engineer-in-charge.

M&L preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion paint of approved tint over a coat of primer complete all as specified & directed by Engineer-in-charge.

M&L preparation of new plastered surfaces of ceiling and applying two coats of white wash complete all as specified & directed by Engineer-in-charge.

vinayandsons

SNEH CORPORATION

Amrita Builders and Consultants