C/o Academic spaces for catalyst labs at ground floor and Technology Innovation Hub at first floor in front of ST1 and ST2 at LP1 area of North Campus of IITMandi (including water supply, sanitary installation, drainage and electrical installation...

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Centering and shuttering including strutting, propping etc. and removal of form work for: Foundations, footings, bases for columns as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Shelves (Cast in situ) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 sqm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing S S 304 grade double shed glass door lock glass to glass 100mm padlock for Fully glazzed door including necessary cutting, hole, fixing accessories and making good etc. all complete as per entire specifications, and as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing S S 304 grade door handle set for fully glazzed door including necessary cutting, hole, fixing accessories and making good etc. all complete as per entire specifications, and as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Supplying and installation of moisture resistant/fire resistant 6 mm thick Heavy duty fiber cement board (High pressure steam cured) conforming to IS 14862:2000 of category III type B as per standard sizes fixed with self-drilling / taping screws. Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of length varying from 25 to 45 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Supplying and installation of moisture resistant/fire resistant 8 mm thick fiber cement board (High pressure steam cured) conforming to IS 14862:2000 of category III type B as per standard sizes fixed with self-drilling / taping screws. Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of length varying from 25 to 45 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing in all exterior face panels breathable vapour barrier underneath the cement fiber board as per National Building Code 2009 complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Designing, providing, installing and fixing factory finished custom designed cold form Light Gauge Steel Framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. The steel sheet shall be galvanized (AZ-150gms Aluminium Zinc Alloy coated steel having minimum yield strength 300-550 Mpa) conforming to AISI specifications and IBC 2009 for cold formed steel framing and construction and also as per IS: 875-1987, ISO 800- 1984 and IS:801- 1975. The wind load shall be as per provisions of IS 875 (part -III). LGSFS frame shall be designed as per IS: 801 using commercially available software such as Frame CAD Pro-11.7/ STAAD PRO-V8i/ArchitekV2.5.16/ Revit architecture-2011 or equivalent. Proper usage of Connection Accessories like Heavy Duty Tension Ties, Light Duty Hold-ons, Twist Straps (to connect truss with wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing Sections, L-Shaped Angles for better structural stability. The framing section shall be cold form C-type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple/slot at required locations as per approved drawings. The slots will be along centre line of webs and shall be spaced minimum 250mm away from both ends of the member. The frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. All self drilling tapping screws for joining the members shall have a Type II coating in accordance with ASTM B633(13) or equivalent corrosion protection of gauge 10 & 12, TPI 16 & 8 of length 20mm. The frames shall be fixed to RCC slab or Tie beam over Neoprene rubber using self expanding carbon steel anchor bolt of dia as per approved drawings. design subject to minimum 12mm diameter and 121mm length conforming to AISI 304 and 316 at 500mm c/c with minimum embedment of 100mm in RCC (RCC to be paid separately) and located not more than 300mm from corners or termination of bottom tracks complete in all respects. The item also includes the submission of stability reports duly examined and issued by any NIT/IIT. The rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / pC.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc .complete as per the architectural drawings and the directions of Engineer-in-Charge.(Cost of aluminium snap beading shall be paid in basic item): With frost glass panes of 5.00 mm thickness complete as per architectural drawings and as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing aluminium handles, ISI marked, powder coated (coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. 200mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing aluminium handles, ISI marked, Powder coated aluminium (minimum thickness of powder coating 50 micron) transparent or dyed to required colour or shade, with necessary screws etc. complete.100 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing aluminium tower bolts, ISI marked, powder coated (coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.200 x 10 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing aluminium tower bolts, ISI marked, powder coated (coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.150 x 10 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing bright finished brass hard drawn hooks and eyes : 300 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

P/F dash fastner /chemical fastner for frame work as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25 mm dia nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 15 mm dia nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 75 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°, 75 mm bend as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°, 110 mm bend as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door 75x75x75 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door 110x110x110 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door 75x75x75 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door 110x110x110 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing Nahani Trap 75mm x 110mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing Stainless steel jalli as per entire satisfaction and direction of Engineer -in-charge as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, 15 mm dia CP Brass single hole sink mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colourweighing not less than 88 gms as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in charge as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing toilet paper holder : C.P. brass as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250 mm diameter as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing ball bearing for rolling shutters as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Electrical Item Wiring for circuit/ submain wiring along with earth wire with the 2 x 4 Sq. mm. + 1 x 4 Sq. mm of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Supplying and fixing stepped type electronic fan regulator 2 Module on the existing modular plate switch box including connections but excluding modular plate etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 5/6 A switch modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 15/16 A switch modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 3 pin 5/6 A socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 6 pin 15/16 A socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 3 Module (100mmX75mm) size/ modules, GI / PVC box alongwith modular base & cover plate for modular switches in recess etc as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 12 Module (200mmX150mm) size/ modules, GI / PVC box alongwith modular base & cover plate for modular switches in recess etc as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 6 way , Double door , single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Supplying and fixing 8 way (8 + 24), Double door, Double door, Double door TPN DB horizontal type prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(excluding MCB/RCCB).as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of Single pole, in the existing MCB DB complete with connections, testing and commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of Triple pole and neutral, in the existing MCB DB complete with connections, testing and commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 63 Amp rating, four pole, (three phase and neutral), 415 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required of make Havells , L&T, Schinder as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing 125 Amp FP MCCB 36 KA rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required of make Havells , L&T, Schinder as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Providing and fixing 400 Amp FP MCCB 50 KA rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required of make Havells , L&T, Schinder as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Laying of one number PVC insulated and PVC sheathed I XLPE power cable of 1.1 kV grade of above 185 sq. mm and upto 400 sq. mm direct in ground including excavation and refilling the trench etc. as required, but excluding sand cushioning and protective covering as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of above 185 sq. mm and upto 400 sq. mm size direct in ground in the same trench in one tier horizontal formation including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of Upto 35 sq. mm (clamped with 1mm thick saddle) on wall surface as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and making end termination with brass compression gland and copper lugs for 3½ X 400 sq. mm (82mm) size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and making end termination with brass compression gland and copper lugs for 4 X 16 sq. mm (28mm) size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Wiring for light point/ fan point/ exhaust fan point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed heavy duty PVC casing caping / PVC Pipe, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required Group B, as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Wiring for circuit/ submain wiring along with earth wire with the 2 x 2.5 Sq. mm. + 1 x 2.5 Sq. mm of FRLS PVC insulated copper conductor, single core cable in surface/ recessed heavy duty PVC casing caping / PVC Pipe as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying, installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying of 3.5 Core 400 Sq. mm of 1.1 KV Aluminium conductor XLPE Insulated, PVC extruded inner-sheathed, round wired GI strip armoured, overall PVC outer-sheathed (as per IS 7098 Part 1) with latest amendments as required of Make :- KEI, Havells, Polycab as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying 4 core 16 Sq. mm XLPE insulated armoured copper cable as per IS7098 (Part 1) 1988 as required of Make :- KEI, Havells, Polycab as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and erection of 8 SWG dia G.I. wire including binding etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 125 amp 36 KA FP MCCB enclosure Double door suitable to accommodate 95 sq. mm 3.5 core Al armoured cable , powder painted including earthing etc. as required of Make:- Havells, Schneider, L&T as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 400 amp 50 KA FP MCCB enclosure Double door suitable to accommodate 95 sq. mm 3.5 core Al armoured cable , powder painted including earthing etc. as required of Make:- Havells, Schneider, L&T as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying and fixing 63 amps rating, four pole, 415 volts,MCB in the existing TPN Box complete with connections, testing and commissioning etc. as required as per entire of Make:- Havells, Schneider, L&T as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all lead and lift..

Supplying and fixing 25 A, MCB DBOXXMCB procted Socket (With Sheet Steel Enclosure) plug top, on surface or in recess, for the socket out let and complete with connections, testing and commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying, installation, testing and commissioning of pre-wired 24W Panel Square / Recessed light (CT up to 6500k) LED Light Fixture, complete with all accessories directly on ceiling, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying, installation, testing and commissioning of 230 mm metal body exhaust fan with metal body shutters in the existing opening, including making good the damage, connection, testing, commissioning etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying, installation, testing and commissioning of pre-wired 12 W Round Surface/ recess panel light (CT up to 6000k) LED Light Fixture, complete with all accessories directly on ceiling, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying, Installation, testing & commissioning of 25 Ltr. geyser including making good the damage, connection, testing, commissioning etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Supplying, installing , testing and commissioning of 400 amps (S.C. rating for 1 sec - 15 KA) 6 way, Copper Bus Bar Chamber. Make:- Havells, Schneider, L&T as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts.

Nipani Infra And Industries Pvt Ltd

MGI Infra Pvt Ltd