PROVN OF TWO AC POINTS, ONE WALL FAN IN KITCHEN, ONE ADDITIONAL WATER HEATER(GEYSER) IN BATHROOM, TWO NOS EXHAUST FANS IN TOILETS AT OFFRS MD ACCN AT VADODARA

Amount

M&L for Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC surface conduit 20 mm dia and conduit accessories fixed on wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), in modular boxes sunken in wall ( with earth dolly) with Modular switch cover for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site as given in Item (NOTE: Modular Switch and socket, modular sunken boxes modular switch cover inner and outer to be measured and paid for separately:- Make of Cable :-Plaza,Finolex,Anchor,Havells,Nicco,Polycab,RPG /Gloster/RR Kabel/KEI Make of PVC Condute:_Anchor,Modi,Presfit,Precision,Astral

One Exhaust fan point controlled by one 5/6 amp switch.

M & L Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper FRLS conductor 2.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC surface conduit 20 mm dia and conduit accessories fixed on wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), in modular box suken in wall with and including PVC insulated multi-stranded copper conductor 2.5 Sq mm nominal cross sectional area single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the one 3/5 pin 15/16 amps socket outlet independent. NOTE: Modular Switch and socket, sunken boxes modular switch cover inner and outer to be measured and paid for separately. (for water heater(Geyser). Make of Cable :-Plaza,Finolex,Anchor,Havells,Nicco,Polycab,RPG /Gloster/RR Kabel/KEI Make of PVC Condute:_Anchor,Modi,Presfit,Precision,Astral

Material and labour for Sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two/four/three single core 1100 v grade PVC insulated unsheathed FRLS cable with stranded copper conductor of nominal cross section area as under drawn into and including PVC non metallic rigid conduit 25 mm on surface as per SSR Part-I with and incl PVC insulated unsheathed FRLS stranded copper conductor of nominal cross section area as under continous earth continuity wire complete all as specified .

Two runs of 4.0 Sq mm as current carrying conductor and one runs of 4.0 Sq mm as earth conductor, Make of Cable :-Plaza,Finolex,Anchor,Havells,Nicco,Polycab,RPG /Gloster/RR Kabel/KEI Make of PVC Condute:_Anchor,Modi,Presfit,Precision,Astral (Note Two runs of 4.00 Sqmm and one run of 4.00 run earth conductor shall measured as one run

Supply and fixing square cover plate with frame suitable for fixing modular type switch/switch sockets/ fan regulator etc of one module all as per Cat No. 575700 of legrend or equivalent in Crabtree,Wipro, L&T or Anchor.

Supply and fixing square cover plate with frame suitable for fixing modular type switch/switch sockets/ fan regulator etc of two module all as per Cat No. 575710 of legrend or equivalent in Crabtree,Wipro, L&T or Anchor.

Supply and fixing modular Metal flush box 1/2 module suitable for fixing modular cover plate with frame to mount/fixing switch/switch sockets/ fan regulator etc of two module all as per Cat No. 689007 of legrend or equivalent in Crabtree,Wipro, L&T or Anchor.

Note for Item No. 4 to 6 : Make of square plate frame & sunken boxes should be of same Make of switch, socket /Regulator etc

Supply and fixing Modular type switch 1 way 6A, 1module, 230 V,AC 50Hz ISI Marked with valid CML No. complete all as per Cat No.573400 of Legrand or equivalent in Crabtree, Anchor Roma/Havells/Polycab

Supply and fixing Modular type switch 1 way 20A, 1module, 230 V,AC 50Hz ISI Marked with valid CML No. complete all as per Cat No.573410 of Legrand or equivalent in Crabtree, Anchor Roma/Havells/Polycab

Supply and fixing Modular type socket outlet multipurpose having provision for 3 pin 16A and 3 pin 6A, 2 module, 230 V,AC 50Hz ISI Marked with valid CML No. complete all as per Cat No.573471 of of Legrand or equivalent in Crabtree, Anchor Roma/Havells/Polycab

Supply and fixing ceiling rose suitable for 230V AC surface bakelite suitable 2/3 for batten fitting complete all as specified.Make- Anchor/Crabtree/Leader/Legrand/Havells/C&S

Supply and fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp IS:3854 marked with valid CML No. complete all as specified. Make- Legrand/Schneider/L&T/ABB/Siemens/Havells

Supply fixing and testing exhaust fan electric single phase AC 240 Volts 50 HZ supply metal body fans of 230 mm sweep size , aluminium pressure die cast motor powder coated paint finished , light weight heavy duty , double ball bearing ,with louvers and connecting including provision 3 core flexible PVC insulated multi stranded copper conductor of size 0.5 Sqmm from ceiling rose/connector to fan incl making suitable hole in existing 230mm thick wall, making good disturbed surgace, four Nos of nuts,bolts and washers for fixing the frame complete all as specified. Model No. Ventil Air - DS 230mm" Make- Havells or equivalent model in Bajaj/CROMPTION/USHA/KHAITAN/Polycab/Almonard

S & F 25 litre Digital storage water heater with five star rating, rated power consumption 2000W, current leakage protection device, multi functional safety valve, high precision thermostat control, preset thermal output, high working pressure 0.8MPa ideal for high rise building, vertical mounting, Power consumption not more than 2000watts, Operating voltage 230 volts. complete rust proof and leak proof including inner tank including all fittings complete & provision of flexible three core PVC insulated multi-stranded copper conductor cable all as directed by Engineer in Charge., Make :- Bajaj/Racold/USHA/Venus/Jaguar/V Guard

S&F Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed 15 mm bore. Make-Soma,Leader,Zoloto,JAQUAR

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed 15 mm bore, Make-Soma,Leader,Zoloto,JAQUAR

Supply and fix Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed fancy type for size 15 mm (1/2”) dia pipe, Make-Soma,Leader,Zoloto,JAQUAR

Supply and fix Stop valves, cast copper alloy, screwed down, high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or forunions and fixed facy type for size 15 mm (1/2”) dia pipe, Make-Soma,Leader,Zoloto,JAQUAR

Supply and fix pipe galvanized, “Medium class”, including fittings 15 mm (1/2”) dia including all fitttings, Make- Tata/Prakash /Jindal/Swastik/Zenith

Supply and fix PVC connections 15mm size with PTMT nuts of length 450mm, Make-MLD/Viking/Khodal or equivalent ISI marked

Supply , installation & commissioning MCB Load Distribution board Vertical type TPN double door, for mounting DP/ SP/TP/ MCBs/MCCBsas Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DP/SP/TP MCB shall be of same make as DB. DB shall also be provided with label marking indicating the incoming and outgoing circuits on all way as specified. The DBs shall be of IP 54 - IK 09 with metal door complete all as specified and directed at site .

DB VTPN 6 way, Cat part No.507746 of Make- Legrand or equivalent in Schneider/L&T/ABB/hAVELLS

S & F MCBs DB TPN 4 way factory made IP 42 protection class metal double door with 200 Amp rating bus bar 240/430V complete all as directed by Engr-incharge. , Cat part No.507670 of Make- Legrand or equivalent in Schneider/L&T/ABB/Havells/Siemens

Supply and Fix only MCCB TPN,100 Amps 4-Pole, 415 volts, breaking capacity16 KA complete all as specified.Cat part No.420015 of Make- Legrand or equivalent in Schneider/L&T/ABB/Siemens

Supply and Fix only MCB TP,63 Amps 4-Pole, 415 volts, breaking capacity16 KA complete all as specified. Cat part No.408661 of Make- Legrand or equivalent in Schneider/L&T/ABB/Siemens /Havells

Supply and Fix only MCB TPN,63 Amps 4-Pole, 415 volts, breaking capacity16 KA complete all as specified.Cat part No.408683 of Make- Legrand or equivalent in Schneider/L&T/ABB/Siemens /Havells

Supply and Fix only MCB TPN,40 Amps 4-Pole, 415 volts, breaking capacity16 KA complete all as specified.Cat part No.408681 of Make- Legrand or equivalent in Schneider/L&T/ABB/Siemens /Havells

MCB , SP ( 6 upto 32 Amp) 240 Volt single pole, breaking capacity 10KA with "C" Charactristic complete all as specified.Cat part No 408587 to 408595 of Make- Legrand or equivalent in Schneider/L&T/ABB/Siemens /Havells

Material and labour for Sub main wiring with approved colour coding as per IS (Red, Yello,Blue and Black for 3 Phase circuit with 2 Single core Green for Earthing) single core 1100 v grade PVC insulated unsheathed FRLS cable with stranded copper conductor of nominal cross section area as under drawn into and including PVC non metallic rigid conduit 32 mm as per SSR Part-I with and incl PVC insulated unsheathed FRLS stranded copper conductor of nominal cross section area as under continous earth continuity wire complete all as specified .

Four runs of 10 Sq mm as current carrying conductor and two runs of 10.0 Sq mm as earth conductor.Make of Cable :-Plaza,Finolex,Anchor,Havells,Nicco,Polycab,RPG /Gloster/RR Kabel/KEI Make of PVC Condute:_Anchor,Modi,Presfit,Precision,Astral (Note Four runs of 10.00 Sqmm and Two run 10.00 of earth conductor shall measured as one run.

Earthing complete with galvanized steel plate electrode 60 cm x 60 cm x 6 mm surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25 meter below ground level with top edge of the earth plate at a depth of not less than 1.50 meter below ground level connected to galvanized iron or steel earth wire, 4 mm dia (No. 8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron, earth wire protected by galvanized steel pipe 15 mm dia (Light grade) & connected to main switch or main control board all as shown in electrical plate No. 5 of SSR-1991 Part I & including necessary excavation and earth work. The rate also include charcoal and salt in alternate layers 20 mm dia pipe (Light grade) for watering, protection pipe, funnel, wire mesh, PCC chamber in cement concrete (1:3:6) type C-I, 40 mm thick RCC (1:2:4) type B-1 cover and CI frame etc. NOTES: - (i) The unit rate includes earthing wire and protection pipe up to 7.5 metre. (ii) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe bends elbow shall be deemed included in the rates.

Labour only for disconnecting power supply from energy meter by carefully opening connection from terminal and depositing into stores for safe custody

Supply and Installation of Three Phase AMR(Automated Meter Reading) system Enabled Bi Direction smart meter with the following specifications:- • AC Three Phase Four Wire, Tamper Proof, Static Meter of Accuracy Class 1.0,3X 240 V, 50 Hz, current 10 A-60A E10conforming to IS-13779 and relevant IEC standards E10 demand display, billing data generation facility, anti-tamper features, Microprocessor and LED based circuitry. Meter Should support the following data :- • Meter should have load limiting switch with the load setting operable from remote software+A2 • Meter should support Tamper event and Power outage detection and reporting to remote software on regular basis • Meter should has In Home display or IHD which shows all electric parameter of energy consumption

• With inbuilt Low Power Radio Frequency (LPRF) communication facility in 865-867 MHz frequency band with Mesh network by default//any other similar suitable communication facility and on demand display, billing data generation facility, anti-tamper features, Microprocessor and LED based circuitry. • 30 minutes instantaneous data for voltage, current, power factor, power, cumulative energy, cumulative apparent energy and frequency, • 30 load survey data for energy, monthly billing survey for Cumulative Energy and Max Demand • Optical port for local communicatin, micro USB, Meter should have connect / disconnect functionality operable from remote software.

• Smart Meter system operate on Low Power Radio Frequency (L.P.R.F)/any other similar suitable communication facility should have a load limiting switch with the load limit operable from the remote software • Provide suitable numbers of Repeater units/convertors(any part of manufacturer for same function) with inbuilt Low Power Radio Frequency (L.P.R.F) communication facility/any other similar communication facility and capable of communicating within mesh network with inbuilt power suppy • Provide suitable numbers of Data Concentrator Units (DCU)/Modems (any part of manufacturer for same function) compatible for remote AMR (Automated meter Reading) system capable of communicatiing with Smart meters in corresponding Low Power Radio Frequency (L.P.R.F) communication facility and with data server(Central Control Unit) through GPRS and should have minimum data transfer rate of 9600 bps. Internal memory to store date of suitable modules for 06 month periods. Should be based on capable of communicating within mesh network within suitable meter range as per site requirement. Including GSM SIM card with suitable recharge value for DCU/Modem unit .

Note : (i) Rate deemed to be included for cost of SIM charges and data hosting charges(cost of data on cloud) or whichever parts required for communication in LPRF mesh type network system/any other similar suitable wireless communication. Data of all 145 AMR smart meters communicated to central unit located at a place as directed connected through GPRS) to generate bills,communication at user end,data collection, control AMR Smart meter. (Existing Married Accomodation divided in to Blocks of 04 Qtrs, 03 Qtrs, 02 Qtr and single bungalows/Qtr - distance range differ from 30 to 100 Mtrs within block and located in two pockets(Outram lines,Lancer Lines) distance 10 KM ). .Make- L&T/Secure/Jaipuria Meters/Elmeasure/Benlo/Havells (ii) Repeater and DCU unit shall be measured and paid sepretally under item No 31&32

Supply only Repeater/convertor(As per Manufacturer design)

Supply only Data concentrator Units(DCU)(As per Manufacturer design)

Supply and configuration of handheld unit alongwith associated base software t collect the data via direct connecting to each meter as required with optical port and collect the data. The HHU unit would provide the LCD graphical display with the memory size of 512 MB or above.Make:- SANDS,ANALOGIC,CRESCO

Supply and Installation of Min 20 Inch Monitor display and Dell PowerEdge T440 or euqivaloent server with the following specifications

• Intel Xeon Bronze 3106 1.7G, 8C/8T, 9.6GT/s , 11M Cache, No Turbo, No HT (85W) DDR4-2133 • Chassis with up to 16, 2.5" Hot Plug Hard Drives, Tower Configuration • 2666MT/s RDIMMs • 2 16GB RDIMM, 2666MT/s, Dual Rank • iDRAC9,Enterprise • 2 1TB 7.2K RPM SATA 6Gbps 512n 2.5in Hot-plug Hard Drive • PERC H730P+ RAID Controller, 2GB NV Cache, Adapter, Full Height • Standard Heat Sink for Less = 150W • DVD +/-RW, SATA, Internal • Dual, Hot-plug, Redundant Power Supply (1+1), 1100W • Jumper Cord,10A,4M,C13/C14 (India BIS) • Deskside Power Cord, GType, 230V,2M (Nepal, Sri Lanka, India) • Trusted Platform Module 2.0 • Dual-Port 1GbE On-Board LOM • Casters, T440 • RAID 1 • Performance BIOS Settings

S& F Color LaserJet Printer performing Print, Copy and Scan, Duplex of Print speed up to 28 ppm (black) and 28 ppm (color). Model HP Color LaserJet Pro MFP M479 dw or other equvalent model of Canon/Epson

S&F for UPS APC SMART-UPS RC 1000VA 230V suitable computer. Make APC,Tata-Liebert,APLAB,Luminous,Sukam

Supply and Configuration of the Web based MDM AND BILLING SOFTWARE Software with following modules:

(i) Meter Data Management Module The meter data management module would be responsible for collecting the data from the concentrator and make the data available to the billing system. The meter data management system would capture and provide the following functionalities: (a) 30 min instantaneous data from all the meters for seven parameters – Cumulative Energy, Cumulative Apparent Energy, Power, Current, Voltage, Power Factor and Frequency (b) Monthly and quarterly billing survey data for cumulative energy and max demand (c) Meter and Meter template setup (d) Data validation and alert set-ups (e) Daily and monthly consumption calculations (f) Energy accounting calculations

(ii) Prepaid / Postpaid Disconnect Billing Module (for single phase and three phase smart meters) The billing module would collect the data from the meter data management module, calculate the energy consumption, calculate billing determinant and calulate the final bills. It should support the following funtionalities: (a) Tariff Set-up including slabs and exemption (b) Billing product set up (mapping consumer ith the tariff) (c) Bill execution (d) Bill dispatch via print, email and sms (e) payment collection from private and other consumers (f) Auto diconnect on meter of payment default

(iii) Occupation and Vacation Module - The system should support occupation and vacation of the officers as well as of other private consumers in the system

(iv) Customer Portal - The ocupatnt officers / customers should be able to view energy data and billing data on web portal as well as in android and IOS apps.

(v) Communication - Email and SMS communication to users and consumers

(vi) User Administration

(vii) MES User Training

(viii) Website setup

(ix) Capable to connect Smart AMR meter upto 3000 Nos of Make:- cresco/inalogics

Taking down old unservisible Distribution boards all as directed by Engineer- in- Charge.

Taking down old unservisible MCCB/MCB TP/TPN all as directed by Engineer- in- Charge.

Taking down old unservisible MCB SP all as directed by Engineer- in- Charge.

Taking down old unservisible Sub main wiring all as directed by Engineer- in- Charge.

Taking down old unservisible earthing all as directed by Engineer- in- Charge.

COMPRENHSHIVE MAINTENACE(AMC)

Comprehensive Maintenance for AMR Meter alongwith all system as specified below:- The AMC shall be start after two year of the defect liability period . The AMC shall be include extended warranty of the hardware supplied, PC, DCU GPRS/Internet(SIM) Charges and data pack of sim for entire duration of AMC, broad band connection for entire duration of AMC including bill payment of brad band connection , data hoisting charges,Software AMC, reconfiguration of the replaced meters, DCU, stationery, cartage of printer, cable of computer and printer,consumabe items , and any minor items are requred during AMC. (Total =145 meters )

JAI ENTERPRISES

City Light