Construction of Degree College at Hatgamharia in West Singhbhum District under Kolhan University, Chaibasa

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for earthwork in hard soil as per specification and direction of E/I. (vide classification of soil item-B)

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation frenches within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l

Providing designation 75A brick work in CM (1:6) in superstructure with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 125 mm thick reinforced designation 75 A brick work in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l.

Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:6) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 112mm thick reinforced designation 100A brickwork fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:4) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including the cost of screening carriage of material scaffolfing raking out joint to 15mm depth curing taxes and royalty (but excluding the cost of reinforcement ) all complete as per building specification and direction of E/I.

Extra for brick work for each consecutive floor above first floor including watering and scafolding, all complete as per direction of E/l.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor,etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:1½:3 (1 cement:1½ coarse sand:3 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete

Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings)

Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like

Weather shade, Chajjas, corbels etc., including edge

Providing, hoisting and fixing above plinth level up to floor five level precast Reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 50 mm thick

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M30 grade with minimum cement content of 350 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level Concrete of M30 grade with minimum cement content of 350 kg /cum

Add for using extra cement in the items of design mix over and above the spedified cement content therein

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 {only valid for TATA (Tiscon),SAIL,JSPL,Electrosteel Steels Ltd. Bokaro and Vizag(RINL)}

Providing Tor steel reinforcement of 10mm ,12mm & 16mm dia. bars as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.

(a) 10mm TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).

(b) 12mm TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).

(c) 16mm TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).

Providing Tor steel reinforcement of 20mm. 25mm. 28 mm, 32mm dia. bars as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. 20/25mm TMT bar Fe 500 (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Supplying , fitting and fixing callapsible gate of apporoved size and make properly fabricated with vertical double channels 20x10x2 mm. at 100mm. Centres and braced with M.S flat diagonals 20 x 3 mm,with top and bottom rails of T. iron 40x40x6 mm with 38 mm dia steel pulleys complete with bolts nuts, locking arrangements stoppers, handles, including applying a primer coat of led paint carriage hosting and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing M.S. grill gate with M.S. grills made of 20x6mm M.S. flats or 16mm square bars fitted on 25x25x6mm M.S Angle frame including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l. (where steel is not supplied by the deptt.)

Providing designation 75A one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I.

Providing 12 mm cement plaster (1:3) with clean coarse sand of F.M 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curring, taxes and royalty all complete as per building specification and direction of E/l.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. With commercial grade colour 15X15cm Tiles.

Providing and laying Double charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less then 0.08% and conforming to IS: 15622/ISO 13006 of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement:4 Coarse sand0, jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with wite cement and matching pigments etc, complete Size of tiles 600 x 600 mm.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 25 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/l.

Making 6x6mm grooves in plaster surface over walls truely horizontal or verical as specified at regular intervals, at all heights including cleaning, finishing scaffoding and curing with all leads and lifts of water all complete as per building specification and direction of E/l.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l.

Providing two coats of synthetic enamal paint of apporoved shade and make over new wooden surfaceincluding cleaning the surface after removing dirt, scales smokes grease and sand papering , including cost of scaffolding and taxes all complete as per building specefication as direction of E/I

Supplying, fitting and fixing 30mm thick solid core type decorative single leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing rust , dirt, , scales , smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/l. ( Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l.

Providing 150mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Water proofing for old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flextble material brush, roller or spray for water proofing coating per manufacturer Specifications with following steps :-(a)surface preparation .-Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing (loose paint / coating, and cement laitance by cleaning with compressed air water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage leakage. On identification of seepage cement grouting to be done with non shrink expanding admixture of Sika India Pvt.L.td.) MYK Schomberg / Dr Fixiti/ Fosroc or equivallent. Providing and reparing of all Corner and joints such as those between the parapet wall and the roof slab etc shall be chamfered with 150Mrn X 150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic pc?' lymer of Sika/ Fosroc/MYK Schomberg/Dr 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent.,Befor 'Chamfering a prime coat shall be given with the slurry of acrylic polymer Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modified repair mortar-including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.(b)lst Coat :- Apply 1st coat of two component acrylic modified, ready to use, flexible cementitiot.is material on surface saturated dry roof and inside wall of Parapet.Wall upto 600 mm by brush or roller . After 1st coat of application , 45 gsm of Fibre glass cloth to lay when the first layer is still green. 1st coat shOUld be applied @1.50 kg/Sqmt/coat. For the purpose of measurer-11609-1'e entire treated surface will be measured." (c) 2nd Coat :-To apply the 2nd coat of two component acrylic modified read to use, flexible cementtiOus material right angle to the 1st. coat over the glass fibre laid surface: 2nd coat-,should be applied @ 0.7 Sqmt/coat. For the purpose of measurement the entire treated surface will be measured." After three days of drying the 2nd coat , the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it. Water proofing Brand:- Sika Topseal 109hi / Fosroc Brushbond RFXI Dr. Fixit Pidiffin 2K / MYK Aquafin TG . Product Performance - Chemical Base Part A: Acrylic copolymer, Part B: Specially graded cementitious powder - Density 1.6 kg/I (mixed density) at +27°C Tensile Strength -2 Nimm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Siren th -2 f\l/mm2 concrete failure Accordin' to ISO4624) Slant-Shear Bond Strength -4 Nimm2 (According to FIP 5.15) Elongation at Break -35% Without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370) (d) )Protection of treated surface with PCG :- The treated surface should be covered with 25mm/50mm F'CC of M-20 grade (1.1.5:3). with proper slope ( 1:120) towards the rain outlets in alternate panels of 2 mt x 2 mt keeping 6 rnm gap between the panel joint. Integral water proofing admixture conforming to IS 2645 co of 100 ml per bag of of cement to be added in the screed concreie(paid separately.for this items).All corners shall be chamfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface should be packed prorSeqswith ridti:corict'ete and the peripheral mouth to be sealed with,moisture insensitive epoxy putty of. Sika India .Pvt.Ltd. / MYK Schornbefg /Dr Fixit/Fosroc .For the purpose of measurement the entire treated surface will be measured." (e)Groove of PCC surface should be filled with POlysulphide Sealant.(Paid Separately). Be d - Sika India Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc . Warranty for five years.

Covering of treated surface with PCC :-providing 25 mm thick Cement Concrete M20 (1:1:5:3) maintaining slope in alternate 2 mt x 2mt panels With approved quality of stone chips of 20mm to 6 mm size graded and Cleaned sand of F.M.2.5 to 3 including screening, shuttering, and mixing Cement concrete in mixer with admixture of integral water proofing and Placing in position, striking curing, taxes and royalty all complete as per Building specification and direction of E/I. Panels that has been left should Be casted next day. There should be 6 mm gap between panels .brand- Sika _ plastocrate plus, MYK proof WP 10, Fosroc- Conplast X 421 ic Dr Fixit Pidiproof LM+

Providing and mixing liquid integral water proffing compound in conctrete of plaster as manufacturer specification and as per direction of engineer in charge. Brand. Sika plastocrate plus, MYK proff WP 10, Fosroc-Conplast x 4211C, Dr.Fixit, Pidiproff LW+ or Equivalent

Providing and filling of 6 mm thick Groove between 25 mm PCC Panels with Polysuiphide Sealant (Porin.g Grade)as per drawings and technical specificationsi6nd direction of E in Charge. (with 18% GST) B rand Sika Polysulphide, Fosrpc-Thioflex 600 Dr. Fixit Pidiseal PS(42P. MY K Seal PS or Euivalent.

HYDT: of Driling 200mm x 165mm x 125 meter.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including supplying all materials, tools,driling rig,air compressure and equipments as well as fuel, lubricants and cost of transportation of rig machine annd other vehical up to Site(Basic rates)

(a) From 0.00 M - 50.00 Meter

(b) From 51.0 M - 125.00 Meter

Supplying submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 metre submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supplying D.O.L. starterwlth SS Enclosure wlth 380/41S Volt coil 5 to 10 H.P.

Supply fitting and fixing GI pipe 50 mm Dia (TATA or equivalent make) Medium Quaility as per IS:1239 ( part 01 ) 2004

Supplying chemical emulsion in sealed containers including delivery as specified.-Chlorpyriphos emulsifiable concentrate of 20%

Treatment of soil under existing floors using chemical emul?sion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:-With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth

Wall lining butch work upto 1 Om height with Dholpur stone 40 mm thick rough facing on the exposed surface with stone strips of minimum length 300 mm and required width, including embedding every tenth layer and bottom most layer in masonry or concrete after making necessary chases of size 75x75 mm and by providing layer of 75 mm thick strips i/c 12 mm thick bed of cement mortar 1 :3 (1 Cement : 3 coarse sand) i/c ruled pointing in cement mortar 1 :2 (1 white cement : 2 stone dust) with an admixture of pigment to match the shade of stone complete as per direction of Engineer-in-charge.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With 12 mm mild steel U beading

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade pigment using 50% white cement 50% Grey cement

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Udaipur green marble

Extra for pre finished nosing to treads of steps of marble stone.

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with:Second class teak wood

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler 75 mm

Coupler 110 mm each

Single pushfit Coupler 75 mm

Single pushfit Coupler 110 mm

Single tee with door 75x75x75 mm

Single tee with door 110x110x110 mm

Single tee without door 75x75x75 mm

Single tee without doo 110x110x110 mm

Bend 87.5° 75 mm bend

Bend 87.5° 110 mm bend

Shoe (Plain) 75 mm Shoe each

Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :'12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.size of (50x75x6mm)

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 178 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia

Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and placing on terrace (at all floo levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and marking necessary holes for inlet outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass Stop Cock (concealed) of standard designand of approved make conforming to IS 8931 15mm nominal bore, approved brand C.P. fittings.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gm

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour: 15 mm nominal bore, weighing not less than 32 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc

15 mm nominal dia Pipes

20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) and For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer?in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With brass cover plate minimum 1.25 mm thickness

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or any other accreditation body which operates in accordance with ISO/ IEC 17011 and accredits labs as per ISO/IEC 17025 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/ m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- inCharge

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately) 25 mm thick

Providing and fixing Sink Cock with Swinging casted spout

Carriage of materials from source to site work including loading & unloading all complete job as per specification and direction of E/I

Sand-(10 KM)

Aggregate -(22 KM)

Stone Metal-(22 km)

Brick-(1+7)km

Fly Ash Brick -(1+7)km

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) With "P" trap (a)10.0 lit. low level PVC cistern

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) 580 mm long (c) with 10.0 lit. low level P.V.C. cistern

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of "Hindustan" " Parry" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l. (a) Flat back or standing corner (600mmX350mm)

Supplying, fitting and fixing C.P. brass towel rail 20mmX600mm with bracket container

Supplying, materrials and labour for constructing inspection chamber of designation class 75B brick size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Point wiring in PVC conduit, with modular type switch:- Wiring for light poinVfan poinUexhaust fan point/call bell point v/ith 1.5 sq.mm FR PVC insulated copper conductor single core in surface/recessed PVC conduit, with modular sw'itch, modular plate suitable GI box etc as required: Group-A

Point wiring in PVC conduit, with modular type switch:- Wiring for light poinVfan poinUexhaust fan point/call bell point v/ith 1.5sq.mm FR PVC insulated copper conductor single core in surface/recessed PVC conduit, with modular sw'itch, modular plate suitable GI box etc as required: Group-B

Point wiring in PVC conduit, with modular type switch:- Wiring for light poinVfan poinUexhaust fan point/call bell point v/ith 1.5sq.mm FR PVC insulated copper conductor single core in surface/recessed PVC conduit, with modular sw'itch, modular plate suitable GI box etc as required: Group-C

Twin Contol point wiring in PVC conduit, with modular Type switch :- Wiring for tw'in control point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way with modular switch, modular plate suitable GI box etc as required

Power Plug Wiring in PVC conduit (2x4 sq. mm): Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 number 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sqmm + 1x1.5 sqmm earth wire

2x2.5 Sqmm + 1x2.5 sqmm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2x6 Sqmm +1x6 sqmm earth wire

2 X 10 sq. mm + 1 X 6 sq. mm earth wire

4x6 Sqmm + 2x6 sqmm earth wire

4x10 Sqmm + 2x6 sqmm earth wire

Wirilg in Existing conduit :- Supplying and drawing following sizes of FR PVC insulated copper conductor single core cable in existing zurface / recessed steel / PVC loonarit including dismantling as required:2x1.5 sq.ffm

TV cable in Existing Conduit: Supplying and drawing co-axial TV cable RG-6 grade 0.7 mm solid copper conductor, PE insulated,shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with acessories in surface/ recess including cutting the wall and making good the same as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required

5/6 amps, switch one way switch

5/6 amps, 3 pin socket outlet

Supply and fixing of following size PVC/G.I. box on surface /recess with suitable size of phenolic laminated sheet cover in front including painting etc as required. 1 or 2 module (78mm x 78mm x 45mm)

Supply and fixing of following size PVC/G.I. box on surface /recess with suitable size of phenolic laminated sheet cover in front including painting etc as required:4/5 module 78m x 140mm x 50mm

Supply and fixing of following size PVC/G.I. box on surface /recess with suitable size of phenolic laminated sheet cover in front including painting etc as required:8/9 module (78mm x 230mm x 60mm)

S/F light plug point with modular type accessories - Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc. as required . (For light plugs to be used in non residential buildings)

S/F power plug point with Modular type accessories - Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface of in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switch connection, painting etc. as required. (For light plugs to be used in non residential buildings)

S/F Ceiling Rose: Supplying and fixing 2 pin 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

S/F Batten Holder: Supplying and fixing batten/angle holder including connection etc. as required.

S/F Electronic Musical Call bell: Supplying and fixing electronic musical call bell suitable for D.C/A.C, single phase 230 volt, complete as required.

ITC fluorescent fitting with downrod :- installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc, including supplying and fixing ball & socket arrangement , 2 nos down rods of 20mm dia stee.

ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

Supplying and fixing rewireable double pole/ TP&N switch disconnector: providing and fixing following DP/ TP&N sheet metal switch disconnector fuse unit in the existing metal board with rewireable type fuses, including drilling holes in metal board, making connections etc as required.

31 amps, double pole

63 amps , TP&N

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc as required.( but without MCB/RCCB/ Isolator):8 way , Double door for each flat

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc as required.( but without MCB/RCCB/ Isolator).:12 way , Double door

Supplying and fixing the follwing way Three Pole pole and Neutral Sheet steel M.C.B distribution board, 415 volts in recess, completed with tinned copper busbar, neutral bus bar, earth bus bar, din bar, hinged front acrylic cover from MCB Knob detachable gland plate, interconnection including earthing etc. as required(without MCB/RCCB/Isolator).

4 way(4+12) Double door Horizontal type

6 way(4+18) Double door Horizontal type

8 way(4+24) Double door Horizontal type

S/F 'C' series SP MCB: Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

6/32 amps Single Pole

6/32 amps SPN

40 amps SPN

40 amps DP

50/63 amps DP

50/63 amps DP

50/63 amps DP

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600mrn x 600mm x 3mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.

Supplying and laying 25mm x 6mm G.I. earth strip in ground :- Providing and laying earth connection from earth electrode with 6 SWG dia G.L Wire in l5mm dia G.I. pipe from earth electrode, as required.

Providing and fixing earth bus 25mmX5mm GI strip on surface for connections etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing and Fixing Lightning Conductor Finial : P/F of lighting conductor finial, made of 25mm dia 300mm long GI tube, having single prong at top, with 85mm dia 6mm thick GI base plate including holes etc. complete as required.

Providing and Fixing GI lightning conductor tape in horizontal run - Providing and fixing of GI tape 20mm X3mm thick on parapet or surface of wall for lighting conductor etc complete as required. (for Horizontal run ).

Providing and Fixing GI lightning conductor tape in Vertical run - Providing and fixing of GI tape 20mm X3mm thick on parapet or surface of wall for lighting conductor etc complete as required.( for Vertical run )

Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 95 sq.mm. but not exceeding 185 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Layrng of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 185 sq mm but not exceeding 400 sq mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required

Laying of one number PVC insulated and PVC sheathed / XLPE power cable not exceeding 35 sq mm of 1.1 KV grade of direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.:Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 95 sq.mm. but not exceeding 185 sq.mm. direct in ground in the same trench one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size not excecding 35 sq mm directr in ground including excavation and refilling the trench etc as rquired, but excluding sand cushioning and protective covering.

Laying of one number PILCA/PVC insulated and PVC sheathed/ XLPE power cable of grade exceeding l.lKV but not exceeding I 1 KV of size not exceeding 120 sq mm direct in ground including excavation, and cushioning, protective covering and refilling the trench

Erection of metalic Pole of following length in cement concrete 1:3:6 ( 1 cement:3 coarse sand : 6 graded stone aggregate 40mm nominal size) foundation including excavation and refilling etc as required.

S.I.T.C of floowing rating LED Street lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage'1.00-270Y AC,50Hz. Luninarie shall be confirm to IS: 10322 part section-3 and sha-ll be complete with all neccssary accessories as required

S.I.T.C of floowing rating LED Flood lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 1C[.Z70Y AC,50Hz. Luminarie shall be confirm tolS:,1,0322part-5/section-5 and shall be complete with allneccssary accessories as required:90/100W LED Flood light

S.I.T.C of floowing rating LED Flood lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 1C[.Z70Y AC,50Hz. Luminarie shall be confirm tolS:,1,0322part-5/section-5 and shall be complete with all neccssary accessories as required:200W LED Flood light

S.I.T.C of floowing rating reccess/surface mounted LED round/square shape Down light luminarie with pressure die cast housing for single phase supply voltage. Luminarie shall be confirm to IS:10322 part-5/section-2 or IEC:62722with all neccssary accossories as required:18/20W LED Round Down light:6/7W LED Round Down light

S.I.T.C of floowing rating reccess/surface mounted LED round/square shape Down light luminarie with pressure die cast housing for single phase supply voltage. Luminarie shall be confirm to IS:10322 part-5/section-2 or IEC:62722with all neccssary accossories as required:18/20W LED Round Down light

Supply Installation, testing and commissioning of follwing size ceiling fan 3 Blades confirming to13:374,.2019 including wiring the down rods of Standard length (upto 30cm) with l.Ssq.mm. FR PVC insulated, copper wire suitable for 230V 50H2, single phase supply etc. complete as required:1200mm (48") BLDC 5star rating 32W Ceiling Fan

S.I.T.C of floowing rating surface mounted LED tube light fitting suitable for 230V 50H2, single phase supply etc. complete as required:20/22W LED Tube light.

S.I.T.C of following rating approved make LED Bollard fitting with rectangular shape of height 600 to 850mm power input-8/9watt with die Cast aluminium housing opel with PC diffuser, lP:55/54 protection confirming to IS:10322 part 5 eE all complete as required. (excluding plinth charge)

Providing of PVC/ XLPE insulated sheathed heavy duty armoured power cable with aluminium conductor of 1.1kV (confirming to IS-1554 part-1) :25 sq. mm,3.5 core

Providing of PVC/ XLPE insulated sheathed heavy duty armoured power cable with aluminium conductor of 1.1kV (confirming to IS-1554 part-1) :35 sq. mm,3.5 core

Providing of PVC/ XLPE insulated sheathed heavy duty armoured power cable with aluminium conductor of 1.1kV (confirming to IS-1554 part-1) :70 sq. mm,3.5 core

Providing of PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including L100 volts. (Conformsto IS:1554,part-1):120 sq. mm,3.5 core

Providing of PVC/ XLPE insulated sheathed heavy duty armoured power cable with aluminium conductor of 1.1kV (confirming to IS-1554 part-1):185 sq. mm,3.5 core

Providing of PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including L100 volts. (Conformsto IS:1554,part-1:300 sq. mm,3.5 core

Providing of PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including L100 volts. (Conformsto IS:1554,part-1:10 sq. mm,4 core

Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required-4 core × 6 sq.mm.(aluminium)

Supply and fixing 7.0m height Octagonal Hot -dip glavinized pole(BOP-7030) :Supply, installation of 7.0m height OctagonalHot -dip glavinized pole with top dia 70mm, bottom dia 130mm & made of 3mm thick sheet, base plate dimension 200x200x12mm(L X B X T) including suitable sizes of foundation bolt all complete as required.( without arm)

Supply and fixing 11 Mtr. height Octagonal Hot - Dip galvanized pole( BOP - 1133) with top dia 90 mm, bottom dia240 mm & made of 3 mm thick sheet, baseplate dimensions 320 X 320X 16 mm ( L x B x T) including suitable sizes of foundation bolt all complete as reqd.:0.5m single arm suitable for 70mm top pole

Supply and fixing 11 Mtr. height Octagonal Hot - Dip galvanized pole( BOP - 1133) with top dia 90 mm, bottom dia240 mm & made of 3 mm thick sheet, baseplate dimensions 320 X 320X 16 mm ( L x B x T) including suitable sizes of foundation bolt all complete as reqd:0.5m double arm suitable for 70mm top pole

Supply of Metal Exhaust Fan 12"(300mm): Supply of 12"(300mm), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required

Supply of Wallmounted Fan: Supply of 16"(400mm), 230V AC wall/cabin fan including fixing the bracket, making , connection testing, commissioning etc as required.

Supplying and fixing of 9/10 Watt LED Bulb accessories as required.

Supply and fixing of Bulk head fitting with 9/10 Watt CFL/LED.

Supply of 12mtr. High mast in one section Construction 5355 grade as per BIEN 10 025 Top Dia 100mm, bottom dia 360mm, plate thickness 3mm, 12side polygon, galvanisation as per BS EN ISO 1461, base plate dia 520mm, base plate thickness 25mm, GI single spike Ughting protection, maximum wind speed 47m/ s as per IS : 875 (Part-III) with 6nos foundation bols of PCD r145mm TS 600/ 24mm dia/850 mm long. Luminaries carriage : Material for 40 NB ERW Class B - M.S. Pipe, dia of carriage ring 450mm (ID) with 8 arm, welded,2 sections having carryingcapacity upto S luminaries. Trailing Cable : 5 core 2.5sq.mm. PVCflexible copper conductor Winch/Power Tool : Double drum, SWL 350Itg with 0.75HP 6 pole single speed integral motor Rope : Grade AISI1304,7 /19 construction, dia 5mm, BLC 1450 x 2 having 2 nos of continueslrope. Aviation obstruction light: twin dome aviation obstruction lights It CO typu as required. (But excluding Feeder Pillar)

ITC of 12 m High mast: Installation, testing and commissioning of 12m high mast shaft and light fixture with help of suitable tools and plants, wiring of luminaries with all wiring materials like PVC insulated PVC sheathed flexible cable of suitable copper conductor lugs, MCB and all labour & construction of shallow foundation with M25 grade concrete for the high mast considering safe soil bearing capacity of 10T/ sq. m for 12m high mast.

Split type AC 1.5 Tr, 5 star: Supply, installation, commissioning of split type Inverter AC 1.5 Tr capacity, 5 star rating as per IS-1391, part-II.

Split type AC 2.0 Tr, 5 star: Supply, installation, commissioning of split type Inverter AC 2.0 Tr capacity, 5 star rating as per IS-1391, part-II.

SITC of 20 KVA online UPS three phase input and three phase output power system of input Voltage range 110V AC I 5% - 300V AC + 5%, Frequenry range 40Hz - 60H2, Power Factor > 0.90 @ full load, and output Voltage range 200Y /2081220/230/240V AC, Voltage regulation t 1%, Frequency range 50Hz t 0.25H2 or 60Hz t .30H2 Harmonic disbortion - < 2o/" THD (Linear load) : 4% THD (non-liniear load) efficiency- 88/83%

SITC of MS battery rack suitable for 30 to 35 UI€ Battery installation

SITC of Copper tube of size( 1/4)" for split AC

SITC of Drain pipe for split AC

Supplying , Flat flexible submersible cable with ,copper conductor , PVC insulated and PVC sheathed as IS:7098 3 Core 4 Sq mm. Copper wire

SITC of 65 Ah flat type Lead acid battery with 24 month replacement guaranty.IS:1652:1991

Supply and fixing of Winch/ power tool for high mast of single arm

Supply and fixing of twin dome aviation light for highmast

Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required. -3.5 × 50 sq.mm.(aluminium)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required:Bell push

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required: 1 Run CAT6 UTP Cable (for Network only)

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as required

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 35 sq. mm (32mm)

3½ X 50 sq. mm (35mm)

3½ X 70 sq. mm (38mm)

3½ X 120 sq. mm (45mm)

3½ X 185 sq. mm (57mm)

3½ X 300 sq. mm (70mm)

4 X 10 sq. mm (25mm)

Supplying and making indoor cable end jointing with cast resin compound, including lugs and other jointing materials for following size of 3 core cable XLPE aluminium conductor cable of 11kV grade as required.:3Cx120 sq.mm

Supplying and making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials for following size of 3 core cable XLPE aluminium conductor cable of 11KV grade as required.:3Cx120 sq.mm

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable,600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Providing and fixing ,testing and commissioning of butterfly valve (PN 1.6) complete with bronze /gun metal srat duty ISI complete with nuts,bolts,washers,gaskets confirming to IS 13095 of following sizes

80 mm diameter

100 mm diameter

150 mm diameter

Providing and fixing ,testing and commissioning of doubled flanged sluice valve of rating PN 1.6 with non rising spindle,bronze/gun metal seat,ISI Marked complete with nuts,bolts,washers,gaskets confirming to IS 780 of following sizes as required

150 mm diameter

200 mm diameter

Providing and fixing ,testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket,GI bolts,nuts,washers etc as required:

80 mm diameter

100 mm diameter

150 mm diameter

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required:Single Headed Gun Metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red,conforming to IS 884 complete with the following asrequired.20 mm nominal internal dia water hose thermoplastic(Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall.Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket:40 m

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636(type-A) as required :Gun Metal

Providing and fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle confirming to IS 903 Suitalbe for instantaneous connection to interconnect hose pipe coupling as required:Gun metal

Supplying, and fixing of fire brigade connection of cast iron body with gun metal male instantaeous inlet couplings complete with cap and chain as required for suitable dia MS Pipe connection confirming to IS 904 as required : 4 way-150 mm dia M.S Pipe

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

100 mm diameter

80 mm diameter

25 mm diameter

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.

200 mm diameter

150 mm diameter

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required :(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.(b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.(c) M.S. fabricated Common base plate, coupling, coupling guard,foundation bolts etc. as required.(d) Suitable cement concrete foundation duly plastered with anti vibration pads.

2850 lpm at 88 m Head

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following,complete in all respects, as required : (Diesel Driven Pump)Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft,mechanical seal conforming to IS 1520.Suitable HP, 1500 RPM water cooled with radiator,diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer,instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.

2850 lpm at 88 m Head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following,complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure,horizontal foot mounted type with Class-'F' insulation,conforming to IS : 325.M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.

180 lpm at 88 m Head

Excavation in Soil using Hydraulic Excavator and Tippers with Disposal upto 1000 metres.- Excavation for road work in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and tranporting to the embankment location within all lifts and lead upto 1000 m

Excavation in Ordinary Rock using Hydraulic Excavator and Tippers with Disposal upto 1000 metres- Excavation for roadwork in Ordinary Rock with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m

Granular Sub-base with Close Graded Material (Table:- 400-1) By Mix in Place Method (Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) for grading- I Material

Lift Panel : The panel includes 415V, 100A, 3Ph, 35kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium, Earth Bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 2.5 ,4, Sq mm PVC Cu. wire. All incomer MCCB and bus coupler shall be mechanically operated . All 4 pole MCCB with thermomagnetic based release must have following character:Incomer,1 No. 63A/FP/ MCB ,Bus bar -100A, 16kA AL,Outgoing,40A ,4P, 30mA RCCB- 1 no,40Amps, TPN, MCB -1 no 16 Amps, DP MCB -1 no,16 Amps, DP RCCB -1 no

LT Panel : Supplying, designing, manufacturing, installation, testing and commissioning of panel fabricated out of 2mm thick(14SWG) CRCA sheet steel, dust and vermin proof with reinforcement of suitable size iron channel of suitable size with proper lifting arrangement effecting proper connection of all incomer and out going (IP-43) fully compartmentalized cubical type wall mounted, totally enclosed, switch board and suitable for use on 415V, 3 phase, AC Supply, 4 wire, 50 C/S, system having 25 kA fault capacity, housed with incoming and outgoing aluminum bus bars, interconnection, interlocking between feeders etc. with indicating lamps, push buttons, necessary accessories, all out going feeders protection as required.The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs:All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for multi runs aluminum cables for all MCCB. Panel shall have individual compartment with name plate.Panel Size - As per Drawing and shall be provided at the time of work order. The Name Plate for each incoming & outgoing feeder must be in Anodized Aluminium Sheet. BUS BARS SECTIONS:The panel includes 415V, 200A, 3Ph, 25kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The current density of bus bar shall be minimum 0.8 A /sq.mm. Al. Bars up to 63A capacity. Other inter connections shall be made with 2.5 and 4 Sq mm PVC Cu. wire. The above panel consisting of the following:-Incomer :1 no-315 ,415V, 4P/36kA MCCB with thermo-magnetic based released type with O/L, S/C protection with adjustable current with spreader links and extended rotary handle. Indicator,Digital Am-meter, three phase,Digital Volt-meter, three phase,CT 500/5VA-5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Phase indicating light shall be protected by 2 Amps SP MCB's for incomer.,Outgoings:19 nos-60A FP/16kA, MCCB with thermomagnetic release type and shall be with spreader links and front rotary handles. including suitable arrangement for cable connection on one side and Bus bar connection on other side. 63A TPN/10kA MCB-'C-series'- 4 nos 40A TPN/10kA MCB-'C-series'- 3 nos 40A DP/10kA MCB-'C-series'- 3 nos AL. bus bar of continious rating 400A

TOTAL AMOUNT FOR SCHEDULE ITEMS (A)

Non -Scheduled item

Non -Scheduled item

Wallmounted Fan 400mm (Platina BLDC): Supply and fitting of 400mm Platina BLDC wall mounted fan including making connection testing, commissioning etc as required..) for indoor sports hall.

Roof Top SPV Power Plant : Design, manufacture, supply, testing & commissioning of grid connected 40 kWp Solar Rooftop Power Plant without Battery backup including 05(five) years comprehensive maintenance contract on turnkey basis. (JERADA 2023(category "B-1")

Providing , fixing Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Providing and fixing 25 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Providing and Fixing Direct Mounting Pressure Gauge Assemble with Gate/Ball Valve -Nominal Size of the Dial-40mm,Measurement Range-0-400,Material of case-Stainless Steel-Gr 304,Material of Dial Plate-Aluminium,Material for Window cover-Transpartent Acrylic,Overall Dimension-500mmX500mmX50mm

Providing and Fixing Air release Valve 150 mm Dia AIR RELEASE VALVE Double Ball Type PN - 10 - Flanges as per BS:4504 PN 10 FF (Drilled) 15 Bar Hyd. 10 Bar Hyd.Pattern / Type-Double Ball Type,Pressure Rating / Class-PN-10,Body-Cast Iron,End Connection-Flanged End,SUB CATEGORY-CI Air Release Valve

Providing and Fixing MS Structure support for piping,Size: 20 X 20 X 3 mm,Thickness: 3 mm,Shape: L Shaped,Usage/Application: Construction,Material: Mild Steel,Structure: T angle

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

Providing , fixing Stainless Steel Text (Text Height 250 mm ) at Pergola Slab with Grouting all Complete Including matrial & Labour as pet E/I

500 kVA TRANSFORMER AS PER IS:1180:- Supply, fitting, fixing, commissioning and testing of 500 kVA , 11 kV/0.433 kV Sealed ,Deta/Star, vector group DYn11, outdoor, Oil Cooled Type ONAN off circuit Star Rating Transformer with copper wound Transformer and civil foundation work along with required size & length of MS channels as per the norms 500 kVA outdoor transformer with all accessories as per IS- 1180 of 2014, air filled cable box suitable for 11kV , 3CX 120sqmm XLPE Al. armoured cable for 1.1kV, 2Run, 3.5Cx300 sqmm XLPE Al. armoured cable as required.) Apart- from the above standard fittings followings items should be included:-Capacity- 500 kVA,Installation - outdoor,No. of phase-Three,Voltage 11kV/433V,Vectro Group -DYn11,Duty- Continuous Tapping in primary-+/- 5% to -10% in 2.5 steps,Type of Tap changer-OCTC,Cooling - ONAN,Insulation class-A,Temp. rise @ 50 Deg. C. Ambient ,Oil by Thermo Meter :- 50 Degree C. In winding by Resistance :- 55 Degree C.

HT Cable 3Cx120 sqmm(UE):- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 6.6kV (UE)grade

Solar LED Standalone Street Light( 45W LED) with low maintenance lead acid battery for 3 day backup: A LED based solar street lighting system consisting of PV modules, electronics ,lead acid battery, and LED based luminaries all suitably mounted on a 6.0m tubular pole above ground , base plate etc as required included . The battery is charged by electricty generated through the PV module panel (180 i.e 90x2 )during day time and the luminaries provides light from dusk to dawn. Specification of of solar LED Standalone street Light: Poly crystalline silicon solar panels, High lumen LED for max. efficiency with lifetime> 50,000 hrs CRI nominal 70. Pressure die cast aluminium IP66 enclosure. Controller to charge batteries & microcontroller for autonomously determination of sunrise & sunset. Specific deep discharge batteries are used to store the energy. Metal battery box to be fitted at 5.0m height , suitable pole

Chemical Earthing Supply, errection, fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure and HDPE Earth Pit Cover 300mm X 300 mm (Under-floor earth inspection pit) having locking arrangement as earth chamber.The above chemical earthing includes the following items (3 Mtr Earthing) Each chemical earthing shall have following details:- Supply of Pollution free Earthcon Compound 4 bags of 25 Kg each Supply of 17.2 mm dia, 250 micron,molecularly bounded copper coated 3 Mtr long electrode. Tested as per IEC 62561-2. Meets the requirement of IS 3043 & IEC 60364-5-54. Tested for short circuit withstanding capacity. High Tensile strength. (UL Listed). Supply of Stainless Steel "U" Bolt Clamp Supply of HDPE Earth Pit Cover for earth chamber (Capacity of 5 ton)

SITC of POE+ Layer 2 Fully Manageable Network Switch consists of 24 X 1G RJ-45 Copper Ports+2x 1G RJ-45/SFP Combo+ 1G RJ-45/SFP+2x1G SFP uplink upgradable to 10G SFP+ Uplink with Fanless Design and internal Power Supply,1 Console Port, 1 USB Management Port,CPU 800MHz ARM v7,File system flash 1 GB,RAM 1 GB, Switching capacity-92 Gb/S,Throughput-67 Mpps, Operating Tempreture- Min-0°C to 45°C (32°F to 113°F), Humidity(Operating)- 5% to 95% non-condensing, Should support IEEE 802.3af, IEEE 802.3at, or 802.3bt compliant end device, Configurable per-port PoE priority and max power for power allocation, Dynamic PoE allocation: Can be configurable to deliver only the power needed by the powered devices (PD) up to the total power budget for most efficient powern consumption, POE Budget min 375 Watt, CE,FCC,UL, RoHS Certified,Layer-2 switching- Up to 16k MAC addresses, Up to 4000 VLANs, Up to 1.5k total system policies, Latency: < 4 μs, Max frame: 9216 bytes (jumbo),Priority queues: Eight hardware-based queues per port for flexible QoS management,Bandwidth management: Flow-based bandwidth management; ingress rate limiting; egress rate shaping per port, Queue management: Configurable scheduling algorithms — Strict Priority,Queuing (SPQ), Weighted Round Robin (WRR), IGMPv1/v2/v3 snooping to optimize multicast traffic, Multicast Listener Discovery (MLD) v1/v2 snooping, Up to 1000 multicast groups, Network Protocols-DHCP,ARP.UDP, Should support- Virtual Chassis (VFL): Link/activity ; Warranty- 1 year

SITC of 8 RJ-45 autosensing 10/100/1000 POE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 2 fixed Gigabit Ethernet SFP ports 1 dual-personality (RJ-45 or USB micro-B) serial console port, POE Power-67 W

SITC of Gigabit Fiber Module-MM, Support up to 550mtr to be used in the switch for uplink purpose and switch and module should be from the same OEM and should provide the OEM certification for genunity of the product

12 Port LIU Switch : SITC of 12 Port Loaded LIU with SC Unit for 12 MM fiber Multi mode fibres OM3 (1 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 12 Fiber Capacity & 12 Nos. of SC Pigtail - Pigtail 1 Meter MM OM3

24 Port LIU Switch : SITC of 24 Port Loaded LIU with SC Unit for 24 MM fiber Multi mode fibres OM3 (12 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 24 Fiber Capacity & 24 Nos. of SC Pigtail - Pigtail 1 Meter MM OM3

SITC of Fiber Duplex Patch Cords SC-LC MM-OM3 Patch Cord 2 mtr.Detailed Specs for Patch Cord, LC SC, Duplex, MM OM3, Bend Insensitive G651, PC, LSZH,Cable : LC/SC-SC/LC 50/125μm MM OM3 Multimode Duplex Patch Cord Length : 2mtrs,Connectors : The optical fiber patch leads shall comprise of Multi mode 50/125μm fiber with 2XLC type fiber connectors terminated at one end of fiber patch cord and 2xSC type connector at other end of the fiber patch cord Insertion loss should be better than ≤ 0.30 dB,Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2 Attenuation: 50/1300 : 3.0/1.0 dB/KM,Connector Loss : 0.30dB(max) Operating Temperature : -40°C to +75°C

SITC of 6-Core OM3 MM Armoured Fibre Optics Cable in Mtrs: Detailed Specs for Outdoor F/O Cable, Loose Tube, MM OM3 – 1x6 Fibers, Central Steel rod with CST, PE,The fiber should be optimized for operation at 850 nm and at 1300 nm.Should fulfill the requirements of ISO.IEC 11801 - 2nd Edition, type MM OM3, ITU-T REC G 651D spec IEC 60794-1-2 F5,No of Cores : 6/12,Max. Attenuation: At 850 nm <= 3.0 dB/km, At 1300 nm <=1.0 dB/km Modal Bandwidth: At 850 nm: ≥1500 MHz.km, At 1300 nm: ≥500 MHz.km,Fibre/Tube Identification : Single Tube,Fibre protection (Tubes) : Polybutylene Terephthalate (PBT),Armouring : CST,Outer Sheath : HDPE >2.0 mm,Pheripheral Strength Member: CST,Cable Diameter (D) : 8.8 ± 0.3 mm,Mass (Nominal) : 82 kg/km,Min. Bending Radius (during Installation) : 20 D;D-Outer Diameter,Max. Tensile Strength-Short Term : 1500N,Max. Crush Resistance-Short Term : 2200N,Operating Temperature range : -40°C to +70°C

SITC of 24 port UTP jack panel (24 port RJ-45 Loaded CAT-6 UTP 19" rackmountable patch panel preferbaly with 6 blocks)Detailed Specs for 19" 1U 24 port unsheilded Patch Panel ,Patch panel should be modular design, populates up to 24 UTP keystone-type jacks in 1U Patch panel should be Enhanced with cable strain relief with retention tray; It should be single metal both front panel and rear tray,Material: sub-rack made of MS Steel with dimension 44.4 mm : 482.6 mm : 105 mm (h:w:d) tray,Information Outlet or connectin module should comply with the specification mentioned above in 2 Standard : Conforms to IEC-60603-7 (603-7) for keystone-type, snap-on apertures Should be RoHS complied

SITC of Straight LAN Patch Chord-1 Mtr Detailed Specs for Patch Cord, U/UTP 4P, Cat.6, length 1/3 Metre,Standardization: Compliant with Cat.6, Class E requirements: ISO/IEC 11801 2nd Edition Compliant with Cat.6 component standards IEC 60603-7-4 and 60603-7-5 ,Cable shield: U/UTP,Number of conductors : 8,Stranding: 7 x 0.20 mm (24 AWG),Cable jacket characteristics: cable, metal-free Cable overall diameter: 6.5±0.2 mm,Tube / Wire type: stranded conductor,Insulation: solid polyolefin, 0.97±0.02 mm diameter Plug: Feature cable retension, with enhanced pull strength. Cat 6 patch cord plug to have round cable holder and strain relief boot to avoid bending,Jacket: PVC with 8 different color options Plug should have high repeatability cross talk performance

Splicing of Armoured SM/MM Fibre Optics Cable: Splicing, testing and commissioning of supplied, OFC cable of 6-Core Armoured Fibre Optics

SITC of Fully Loaded 15U 19" 600*600 Wall Mounted Rack with all required accessories -2 Nos. of Fan,6A 6 Plug PDU-1 Nos. ,Cable Manager-2 Nos., Mounting Screws-20 Pcs ;

SITC of 5MP Fixed Lens Network Bullet Camera with following Technical Specifications;Feature Specification Image Sensor: 1/2.7'' Progressive Scan CMOS Min. illumination: Color: 0.003 Lux @ (F1.4, AGC ON), B/W: 0 Lux with IR,Preferred recording Resolution: 5MP (2592x1944) or better Day & Night: IR Cut Filter,Shutter speed: 1/3 s to 1/100,000 s Digital Noise Reduction: 3D DNR,WDR: 120dB True WDR or better Lens: 4mm,IR range: 40m IR or higher,Streaming Type: Should Support quad video streams or better,Video Compression: H.265,H.264, H.264+,H.265+,MJPEG and Main stream supports H.264+/H.265+,Audio,Compression:G.711ulaw/G.711alaw/G.722.1/G.726/MP2L2/PCM/MP3,Image Enhancement: BLC, HLC, 3D DNR, EIS, Defog,ROI(5 fixed regions for main stream and sub-stream). Image settings: Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser Day/Night Switch: Day, Night, Auto, Schedule Network Protocol: TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, NTP, UPnP, SMTP, IGMP, 802.1X, QoS, IPv4, IPv6, UDP, Bonjour, SSL/TLS, PPPoE, ARP, SNMP,Open Network Video Interface (PROFILE S, PROFILE G, PROFILE T),ISAPI. Simultaneous Live View: 6 channel,User Host: 32 users. 3 user levels: administrator, operator and user,Security: Password protection, complicated password, HTTPS encryption, IP address filter, Security Audit Log, basic and digest authentication for HTTP/HTTPS, TLS 1.2, WSSE and digest authentication for Open Network Video Interface, memory card encryption.Edge base Recording storage: Built-in memory card slot, support microSD card, up to 256 GB Preferable analytics features: Motion detection, video tampering alarm, Line crossing detection, intrusion detection,scene change detection, video quality diagnosis. Event Alarm: Notify surveillance center, trigger recording, trigger capture, send email, audible warning,network disconnected, illegal login. Ethernet Port: 1 x RJ45 10M/100M Ethernet port Audio interface: 1x input, 1x output Power Supply: DC12V, PoE (802.3af) Operating Conditions: -30° C ~ + 60° C Ingress Protection: IP67 Certifications: CE, FCC, UL,BIS.

SITC of 5MP Fixed Lens Network Dome Camera with following Technical Specifications;Feature : Specification Image Sensor: 1/2.7'' Progressive Scan CMOS Min. illumination: Color: 0.003 Lux @ (F1.4, AGC ON), B/W: 0 Lux with IR,Preferred recording Resolution 5MP (2592x1944) or better Day & Night: IR Cut Filter,Shutter speed: 1/3 s to 1/100,000 s Digital Noise Reduction: 3D DNR,WDR: 120dB True WDR or better Lens: 4mm,IR range: 40m IR or higher,Streaming Type: Should Support quad video streams or better,Video Compression H.265,H.264, H.264+,H.265+,MJPEG and Main stream supports H.264+/H.265+,Audio Compression: G.711ulaw/G.711alaw/G.722.1/G.726/MP2L2/PCM/MP3,Image Enhancement: BLC, HLC, 3D DNR, EIS, Defog,ROI (5 fixed regions for main stream and sub-stream). Image settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser Day/Night Switch: Day, Night, Auto, Schedule Network Protocol: TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, NTP, UPnP, SMTP, IGMP, 802.1X, QoS, IPv4, IPv6, UDP, Bonjour, SSL/TLS, PPPoE, ARP, SNMP,Open Network Video Interface (PROFILE S, PROFILE G, PROFILE T),ISAPI. Simultaneous Live View: 6 channel,User Host: 32 users. 3 user levels: administrator, operator and user,Security: Password protection, complicated password, HTTPS encryption, IP address filter, Security Audit Log, basic and digest authentication for HTTP/HTTPS, TLS 1.2, WSSE and digest authentication for Open Network Video Interface, memory card encryption.Edge base Recording storage: Built-in memory card slot, support microSD card, up to 256 GB Preferable analytics features: Motion detection, video tampering alarm, Line crossing detection, intrusion detection,scene change detection, video quality diagnosis. Event Alarm: Notify surveillance center, trigger recording, trigger capture, send email, audible warning,network disconnected, illegal login. Ethernet Port: 1 x RJ45 10M/100M Ethernet port Audio interface: 1x input, 1x output Power Supply: DC12V, PoE (802.3af) Operating Conditions: -30° C ~ + 60° C Ingress Protection: IP67 Certifications: CE, FCC, UL,BIS.

SITC of PTZ Camera: Sensor :-1/1.9’’ Progressive Scan CMOS,Optical Zoom:-Minimum 23x or better,Digital Zoom:-Minimum 12X or better,Resolution:-Minimum 1920 X 1080 or better,Min. Illumination-Color: 0.002 lux @ (F1.5, AGC ON), B/W : 0.0002 lux @ (F1.5, AGC ON), 0 lux with IR,Lens:-5.9-135.7mm, 23x,Wiper-Wiper Support,Video Compression:-H.264/MJPEG,Wide Dynamic Range-120dB,Multi Streaming-Camera should support Multi streaming,Supported Protocols:-IPv4/IPv6, HTTP, HTTPS, 802.1X, QoS, FTP, SMTP, UPnP, SNMP, DNS, DDNS, NTP, RTSP, RTP, TCP, UDP,IGMP, ICMP, DHCP, PPPoE,Network Interface:-10Base-T / 100Base-TX, RJ45 connector,Network Interface:-10Base-T / 100Base-TX, RJ45 connector,PAN & TILT Range:-Pan:360° endless; Tilt: -20°~90°,Simultaneous Live View-Up to 20 users,Protection Level:-IP66, IK10, TVS 6,000V lightning protection, surge protection,Alarm Trigger-Smart tracking when patrol between multiple scenarios,Face detection, intrusion detection, line crossing detection, audio exception detection, region entrance, region exiting detection,Smart detection-Face detection, Intrusion detection, Line crossing detection, Audio exception detection, Region entrance detection, IR Range:-Upto 150 Meter or Better,Certification:-FCC,CE,UL,Housing:-Vandal Proof ( IK 10 or better),ONVIF-Camera should be ONVIF Compiled,Enhancement-3D DNR,HLC, EIS, Defog,Power:-High-PoE&24 VAC, Max.60W,Humidity:90% or better,Temperature:-Minimum -40°C ~ 65°C (-40°F ~ 149°F)

SITC of 8 TB Surveillance Grade Hard Disk for NVR for 30 Days Back up of specification:Form Factor 3.5,Capacity (TB) 8 terabyte,Cameras supported :64,Number of USB 2 Ports: 0,Interface :SATA 6 Gb/s,Workload Rating (TB/year) :180,OS Supported: Windows,NVR-Ready :Yes,Bay Count Support :8,Cache (MB): 256,Water Resistant: No,Shock Resistant: No,Dimension (W x H x D) (mm x mm x mm) -Weight (Grams): 780 gram,Wattage (Watts) 9,Standard Accessories to be supplied :NA,Operating Temperature Range (Degree C) :5-70,Operating Humidity (% RH) :90,Availability of Test Reports from Central Govt / NABL approved / ILAC acredited lab to prove conformity to the specification (Test reports are to be furnished when demanded by buyer): Yes

Supplying of 55" 4k LED Panel of specification: Type/Category/Class of TV set:Smart TV(2),Display Type/Technology:LED (Light Emitting Diode),Nominal Screen Size Range (Inches):more than 55 inch -upto 80 inch,Audio Power (minimum):20W x 2,Maximum Resolution (Pixels) supported:4K Ultra HD (UHD): 3840x2160,Typical Brightness (Nits):400 - 499,BEE Star Rating:2 star,Comprehensive Standard Warranty(Years) Comprehensive Standard Warranty(Years):1 Warranty on Display only (Years):2

Supply, fitting, fixing, commissioning and testing of 35 Sq. MM Copper Conductor Multi strand PVC Sheilded FRLS Wire with suitable Copper LUGS for Battery Interconnection and suitable 50 Sq. mm copper wire of 4 length of 10 mtrs each for UPS to Battery excluding cable from PANEL to UPS and UPS to panel.

Chemical Earthing Supply, errection, fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure and HDPE Earth Pit Cover 300mm X 300 mm (Under-floor earth inspection pit) having locking arrangement as earth chamber.The above chemical earthing includes the following items (3 Mtr Earthing) Each chemical earthing shall have following details:- Supply of Pollution free Earthcon Compound 4 bags of 25 Kg each Supply of 17.2 mm dia, 250 micron,molecularly bounded copper coated 3 Mtr long electrode. Tested as per IEC 62561-2. Meets the requirement of IS 3043 & IEC 60364-5-54. Tested for short circuit withstanding capacity. High Tensile strength. (UL Listed). Supply of Stainless Steel "U" Bolt Clamp Supply of HDPE Earth Pit Cover for earth chamber (Capacity of 5 ton)

Supplying & Placing Dual Desk, PLPB Edge Banded Top, Seat & Back,Powder Coated Pipe Frame, Top Size - 1050 X 400 X 18mm Thick Overall Size - 1050 X 980 X 750 Material of Desk Top +/- 2 mm (For shelf / storage +/- 4 mm) 20 mm thick MDF Board of grade SBG II conforming to IS 12406 laminated with minimum 0.6 mm thick on Top side of type S, P or F having index 3.2.3 conforming to IS 2046 and minimum 0.5 mm thick balancing laminate on the other side Material of Support Structure or Side Pannel Mild Steel square Section of size 25x25 mm and wall thickness minimum 1.6 mm Height of Desk Top in mm (±5 mm) 750 Width of Desk Top in mm (± 5 mm) 450 TYPE OF DESKING INTEGRATED DESK CUM SEATING WITH SHELF / STORAGE UNDER DESK Desking Configuration TWO SEATER Length of Desking, Seating and Backrest (if provided) in mm (±10 mm) 1050 Material of Seat and Backrest (if provided) (+/- 2 mm (For back rest +/- 4 mm) 20 mm thick MDF Board of grade SBG II conforming to IS 12406 laminated with minimum 0.6 mm thick on Top side of type S, P or F having index 3.2.3 conforming to IS 2046 and minimum 0.5 mm thick balancing laminate on the other side Material of Support Structure Mild Steel square Section of size 25x25 mm and wall thickness minimum 1.6 mm Material of Seat Cushion WITHOUT CUSHION Width of Seating in mm (±10 mm) 300 Height of Seat in mm (±10 mm) 460 Width of backrest if provided in mm (± 5 mm) 200 Back Support for Seating of Same materail as Seating Provided without cushion

Supplying & Placing Three Seater Desk, PLPB Edge Banded Top, Seat & Back, Powder Coated Pipe Frame, Top Size - 1500 X 400 X 18mm Thick Overall Size - 1500 X 980 X 750 Material of Desk Top +/- 2 mm (For shelf / storage +/- 4 mm) 18 mm thick prelaminated Particle Board Material of Support Structure or Side Pannel Mild Steel Pipe of diameter 25 mm and wall thickness 1.1 mm minimum Height of Desk Top in mm (±5 mm) 750 Width of Desk Top in mm (± 5 mm) 400 TYPE OF DESKING INTEGRATED DESK CUM SEATING Desking Configuration THREE SEATER Length of Desking, Seating and Backrest (if provided) in mm (±10 mm) 1050 Material of Seat and Backrest (if provided) (+/- 2 mm (For back rest +/- 4 mm) 18 mm thick prelaminated Particle Board Material of Support Structure Mild Steel Pipe of diameter 25 mm and wall thickness 1.1 mm minimum Material of Seat Cushion WITHOUT CUSHION Width of Seating in mm (±10 mm) 450 Height of Seat in mm (±10 mm) 460 Width of backrest if provided in mm (± 5 mm) 200 Back Support for Seating of Same materail as Seating back support not provided

Supplying & Placing 1200 mm x 610 x Excutice computer table Type of Computer Table Computer table with key board drawer and table top Construction of Computer/Printer Table Gable end and modesty panel Colour of Top As per Buyer's Choice Material of table top,keyboard and drawer Three layer prelaminated particle board(Wood Product) of grade II type II of IS 12823/Latest Gable end and Modesty panel material Three Layer prelaminated particles board(wood product) of grade II type III of IS 12823/Latest Leg Material NO LEGS Table top thickness ±2mm 19 millimeter Thickness of gable end and modesty panel ±2mm 19 Dimension of leg(mmXmm) ±5mm No legs Length of table in mm (±15 mm) 1200 millimeter Depth of table in mm (±10mm) 610 millimeter Height of table in mm (±10mm) 760 millimeter Type of keyboard tray Wooden keyboard tray Material of footrest No footrest Material thickness of footrest ±2mm No footrest Product having BIFMA certification YES OEM of offered product is ISO 9001:2015 certified YES OEM of offered product is ISO 14001:2015 certified YES OEM of offered product is ISO 18001:2007/45001:2018certified YES

Supplying and PlacingWriting Board 1200mm x 3000mm Purpose : Writing Mounting type : Wall mounts Frame (All round framing) : With, Writing board placed Top Surface materials (Usedfor white board surface) : Porcelain Top surface material thickness : 0.7 mm to 0.8 mm Frame material :Anodized extruded aluminum alloy hollow section conforming to IS 733

Supplying and Placing Wooden Podium Design Gable end and modesty panel and top material teak wood with all complete finishings and specifications: Mode of supply:Assembled Ready To Use,Understructure of podium:Gable end and modesty panel,Storage:Open Storage,Shelves:2 - shelves,Reading surface:Flat surface,Top position:Fixed,Paper stop:No,Wire management:without,Number of socket box:0,In built sockets for LAN / Internet:No,Type of socket box:No socket box,Podium top Material:Commercial Block Board MR Grade Conforming to IS 1659,Gable end and modesty panel material:Commercial Block Board BWP grade Conforming to IS 1659,Leg Material:NO LEGS,Podium top plain sides:CP Teak Wood Lipping Gable end and modesty panel plain side:CP Teak Wood Lipping,Thickness of podium top ±2mm:19 millimeter,Thickness of gable end and modesty panel ±2mm:19 millimeter,Length of podium top ±10mm 650 millimeter,Depth of podium ±10mm:500 millimeter,Height of podium ±10mm:1175 millimeter,Presenter side height ± 10mm:1100mm,Dimension of leg (mmXmm) ±5mm:No legs,Width of shelves ±10mm:500mm,Depth of shelves in mm (±10mm):400mm,Length of footrest ±10mm:600mm,Depth of footrest ±10mm:350mm,Height of footrest (front / back) ±10mm:125mm/75mm,Material thickness of footrest ±2mm:19mm,Podium top finish:Teak laminate/ply with polish Table top shade,As per Buyer's choice,Warranty period in number of years:2,Test reports to be furnished to buyer on demand:NO

Supplying & Placing Executive Table, Particle Board Top W1600 X D1600 X H750 Structure /Frame of table Gable end and modesty panel The type of Storage provided One side E.R.U unit Keyboard tray Not provided Footrest Not Provided Tabletop Material Commercial Block Board MR Grade Conforming to IS 1659 Thickness of table top material (± 1 mm) 36 mm Gable end material Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest The thickness of the gable end NA Modesty panel material Perforated MS sheet The thickness of the modesty panel material 0.9 mm (for metal sheet) Leg Material Mild Steel (MS) ERW The thickness of the Leg material 1.2 mm Width of tabletop ±10 mm 1500 mm Depth of table ±10 mm 915 mm Height of table ±10 mm 750 mm Size (L x W) /diameter of leg material ± 5 mm NA ERU unit consists of 3 drawers Total Number of drawers /storage in Pedestal units Four drawers Table top finish Laminate in color with swede finish 0.6-0.8mm thickness of type S, F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on another side Tabletop shade Oxford cherry Table /ERU /Pedestal Panel Plain Side Edge to be banded with PVC tape 2 mm thick with the help of hot melt glue

Supplying & Placing Medium Back Chair, Chrome Plated Pipe PU Arm, Gas Lift, Chrome Base, Mesh Back & Seat Net Tapestry Chair mechanism Tilt working with torsion bar mechanism Type of locking Upright locking Number of arm movement N.A Pedestal Base Chrome plated MS Armrest Material Polypropylene Seat material Pressed and moulded with PU foam Backrest is made of One piece hot pressed plywood with PU foam Density of PU foam used in seat KG per Cu Meter (± 3) 40 Density of PU foam used in backrest in KG per Cu Meter (±3) 40 Backrest upholstered with 100% Polyester Fabric Seat upholstered with 100% polyester fabric GSM/Thickness of fabric ±5%(Gram/Square meter) 220 gram Overall width (±10 mm) 650 mm Backrest Height ±15 mm 690 mm Backrest Width ±10 mm 440 mm Seat Height ±10 mm 440 mm Seat Width ±10 mm 480 mm Seat Depth ±10 mm 480 mm Thickness of MS Plate Joining the under structure with Seat 5 mm Thickness of Plywood used in Seat ±1(mm) 12 mm Thickness of Plywood used in Backrest ± 1(mm) 12 mm Pedestal Size (Diameter in mm) ±10 mm 600 mm Thickness of Polyurethane Foam Used in Seat in mm (±2 mm) 30 mm Thickness of Polyurethane Foam Used in Backrest in mm((±2 mm) 35 mm

Supplying & Placing Visitor Chair, Cushion Arm, PU Moulded Seat Back, Chrome Plated Pipe stand Leatherette Tapestry Chair Type Non-Revolving and Non-Tilting chair with Armrest Chair frame type Legs Armrest type Continuous armrest Seat type Padded Backrest type Padded Frame Material Configuration Two Piece Frame material Stainless Steel (SS 202) Seat material Moulded Plywood Seat material thickness 30 mm Density of Polyurethane foam used in seat (±2 Kg/Cub Meter) 40 Seat upholstered with PU sheet GSM of seat cover (± 3 GSM) 390 GSM Backrest material Moulded Plywood Density of Polyurethane foam used in Backrest ( ±2 Kg/Cub Meter) 32 Backrest upholstered with PU sheet Seat Depth (± 5 mm) 430 mm Seat Width (± 5 mm) 460 mm Seat height from floor surface (± 5 mm) 475 mm Backrest width (± 5 mm) 450 mm Backrest height from seat (± 5 mm) 460 mm Paint Type Chrome Paint Polish Type N.A Colour of Paint N.A Availability of Test Report from Central Govt/NABL/ILAC accredited lab to prove the conformity of product to the Specification Yes Test reports to be furnished to buyer on demand Yes

Supplying & Placing workstation table in completely knock down conditions with an overall size 4000mm X 1260mm X 1200mm that is to be assembled at site. The worktop shall be made up of back to back 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in sharing base rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The top shall be supported on particle board base gable end. The end wall of the top shall be topped by gable end. It should be made up of 25mm thick Pre-laminated particle board and the profile shall be in linear shape with appropriate PVC edge banding. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in front side of user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with 40-60µ thick. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways & 4 ways (L-cover for corner, T-cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) provided at front of the user. Laminated bottom tile shall be situated below the work top. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. Fixed pedestal shall be provided with an overall size 400mm X 450mm X 725mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 4 nos. of drawer having same size. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A nylon castor based CPU unit shall be provided with an overall size 470mm X 286mm with 18mm thick Pre-laminated particle board. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Supplying & Placing Medium Back Chair, PP Arm, Gas Lift, Nylon Base, PU Moulded Seat & Back, PP Seat & Back Cover, Fabric Tapestry Chair mechanism Centre pivot mechanism Type of locking Tilt limiter Number of arm movement N.A,Pedestal Base Chrome plated MS Armrest Material Polypropylene Seat material Pressed and moulded with PU foam Backrest is made of One piece hot pressed plywood with PU foam Density of PU foam used in seat KG per Cu Meter (± 3) 45 Density of PU foam used in backrest in KG per Cu Meter (±3) 40 Backrest upholstered with 100% Polyester Fabric Seat upholstered with 100% polyester fabric GSM/Thickness of fabric 5%(Gram/Square meter) 290 gram Overall width (±10 mm) 590 mm Backrest Height ±15 mm 600 mm Backrest Width ±10 mm 480 mm Seat Height ±10 mm 460 mm Seat Width ±10 mm 460 mm Seat Depth ±10 mm 410 mm,Thickness of MS Plate Joining the under structure with Seat 0.3 mm Thickness of Plywood used in Seat ±1(mm) 12 mm Thickness of Plywood used in Backrest ± 1(mm) 12 mm Pedestal Size (Diameter in mm) ±10 mm 600 mm Thickness of Polyurethane Foam Used in Seat in mm (±2 mm) 30 mm Thickness of Polyurethane Foam Used in Backrest in mm((±2 mm) 30 mm

Supplying & Placing Conference table in completely knock down conditions with an overall size 3600mm X 1200mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall have the size 1800mm X 1200mm made up of 2 nos. of 50mm thick pre-laminated particle board of grade II of IS 12823 with one side laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edgebander machine at 200 0C. The table top shall be supported by particle board base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall have the size 1050mm X 695mm with 49mm thick and 100mm X 695mm with 18mm thick. The gable end shall be made up of Pre-laminated particle board with appropriate PVC edge banding and covered both side by Aluminium section. The table shall be clad with 18mm thick modesty panel which provide structural support for the desk. The modesty panel shall have an overall size 1200mm X 400mm with 18mm thick pre-laminated particle board connected with both end. There shall be buffers provided to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturershall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Supplying & Placing 3 Seater Sofa With SS Arms & Legs, Perforated Seat & Back, Powder Coated Beam Size in mm - 1750(L) X 710(D) X 755(H) SS 304 Style with arm and backrest Seating Capacity (Nos) 3 Material of Main Frame SS 304 Material of Seat and Backrest SS 304 Material of Arms SS 304 Material of Legs SS 304 Material of Side Bar Bracket made up of chrome plated solid steel Overall Length in mm (±10 mm) 1800 Overall Depth in mm ( ±5 mm) 665 Overall Height in mm (±5 mm) 760 Conforming to International Standard for Public Seating (*BIFMA X 5 dot 4 or equvalent) YES All steel component to be epoxy powder coated 60 micron thick

Supplying & Placing Modular table in completely knock down conditions with an overall size 2650mm X 2200mm X 750mm that is to be assembled at site. The worktop shall have the size 2200mm X 1000mm x 76mm thick made up of Medium Density Fibre-board with approved veneer laminate and PU polish accordingly. The table top profile shall be in rectangle shape with round corners and full round post forming edges. The table top shall be supported on MDF board based gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 76mm thick medium density fibre-board and profile shall be in moulded construction with full round post forming edges and duly deco painted. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick medium density fibre-board in linear shape with appropriate PVC edge banding and veneer laminate. There shall be buffers provided at the base to avoid scratches on the floor. The table shall have side unit for storage purpose with an overall size 2200mm x 600mm X 600mm. It shall have 2 nos. of drawer, 1 nos. of filling space with door and 1 nos of open space . The drawer shall be operated with profile handle and easily close & open with the assistance of sliding channels to enable smooth operation and sliding rail track and concealed crank hinge. Drawer facai, sides and all other shall be made in 18mm thick and drawer base shall be 9mm thick. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. The complete structure shall be supplied with approved veneer laminate, PU polish and deco painted. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.

Supplying & Placing High Back Chair, SS Wooden Arm, Synchro Knee Tilt, Gas Lift, Die Cast Aluminium Base Pure Leather Chair mechanism Knee tilt Synchronic mechanism Type of locking 5-Position Locking Number of arm movement N.A Pedestal Base Aluminium die cast Armrest Material MS chrome plated Seat material Pressed and moulded with PU foam Backrest is made of One piece injection moulded frame Density of PU foam used in seat KG per Cu Meter (± 3) 35 Density of PU foam used in backrest in KG per Cu Meter (±3) 35 Backrest upholstered with Pure Leather Seat upholstered with Pure leather GSM/Thickness of fabric ±5%(Gram/Square meter) N.A Overall width (±10 mm) 550 mm Backrest Height ±15 mm 500 mm Backrest Width ±10 mm 440 mm Seat Height ±10 mm 480 mm Seat Width ±10 mm 460 mm Seat Depth ±10 mm 430 mm Thickness of MS Plate Joining the under structure with Seat 0.3 mm Thickness of Plywood used in Seat ±1(mm) 18 mm Thickness of Plywood used in Backrest ± 1(mm) 12 mm Pedestal Size (Diameter in mm) ±10 mm 620 mm Thickness of Polyurethane Foam Used in Seat in mm (±2 mm) 35 mm Thickness of Polyurethane Foam Used in Backrest in mm((±2 mm) 40 mm

Supplying & Placing Visitor Chair, Wooden Frame, Chrome Cushion Arm, Chrome Plated Pipe Stand Pure Leather Chair Type Non-Revolving and Non-Tilting chair with Armrest Chair frame type Cantilever Armrest type Moulded T armrest fitted with seat bottom Seat type Padded Backrest type Padded Frame Material Configuration Two Piece Frame material Stainless Steel (SS 304) Seat material Moulded Plywood Seat material thickness 18 mm Density of Polyurethane foam used in seat (±2 Kg/Cub Meter) 45 Seat upholstered with Leather GSM of seat cover (± 3 GSM) 250 GSM Backrest material Moulded Plywood Density of Polyurethane foam used in Backrest ( ±2 Kg/Cub Meter) 55 Backrest upholstered with Leather Seat Depth (± 5 mm) 470 mm Seat Width (± 5 mm) 520 mm Seat height from floor surface (± 5 mm) 455 mm Backrest width (± 5 mm) 510 mm Backrest height from seat (± 5 mm) 580 mm Paint Type Chrome Paint Polish Type As per Buyer’s Requirement (to be indicated during bid creation)

Supplying & Placing 3 Seater Sofa With Wooden Frame, Powder Coated Leg, Twin Colour Leatherette Tapestry Size in mm - 1930 (L) X 790 (D) X 850 (H) Total Number of Seats in the Sofa Set 3 Number of Single Seater Units (Nos) No Single Seater Unit Number of Two Seater Units (Nos) No Two Seater Unit Number of Three Seater Units (Nos) 1 Number of Four Seater Units (Nos) No Four Seater Unit Frame Covering Fully Upholstered Sofa Set is Foldable to use as bed No Backrest Cushion Material Foam Density of Cushion of Backrest Material (Kg/Cubic M) 32 Covering Material for Seat and Backrest Genuine Leather Frame Structure Material and size (±1 mm) 19 mm thick Commercial board Seat Cushion Material Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M) 40 Type of Spring in the Base / Seating Eight way hand tied spring Length of Single Seater Units in mm (±5 mm) 508 Length of Two Seater Units in mm (±10 mm) 1100 Length of Three Seater Units in mm (±10 mm) 1850 Length of Four Seater Units in mm (±10 mm) 2640 Depth of Sofa Units in mm (±10 mm) 775,Sofa Height (Without Back Cushion) ±5 (mm) 430 millimeter Sofa Height (With Back Cushion) ±5 mm 845 millimeter Seat Cushion Length ±5 (mm) 525 Seat Cushion Width ±5 (mm) 710 Seat Cushion Thickness ±3 (mm) 210 Backrest Cushion Length ±5 (mm) 530 Backrest Cushion Width ±5 (mm) 530

Supplying & Placing Centre Table, 12mm Toughened Glass, MS Powder Coated 1200 X 600 X 450 Understructure Number of storage under top No storage Top material Tempered glass Frame material Other wood Dimension of Top (Length X Breadth, or Diameter) ±20mm 1194mmX584mm Height of centre table ±10 mm 460 millimeter Thickness of top material (+/-2 mm) 12 millimeter Thickness of frame material (+/- 1 mm) 12 millimeter

Supplying & Placing Back Storage Unit, 18mm PLPB, Extruded Aluminium Profile W2250 X D450 X H2200 Material of Construction ISI Marked, three layer Prelaminated particle Board conforming to Grade II Type III of IS 12823/2013 laminated with 0.6-0.8 mm thick lamination conforming to IS 2046/1995 and balancing lamination of 0.5 mm thick on the back side Number of Shelves (Nos) 4 Number of Doors (Nos) 4 Height in mm (±10 mm) 2100 Depth in mm (±5 mm) 450 Width in mm (±10 mm) 1830 Thickness of Top in mm (±2 mm) 18 Thickness of Sides in mm (±1 mm) 18 Thickness of Back in mm (±1 mm) 10 Thickness of Bottom in mm (±1 mm) 18 Thickness of shelf in mm (±1 mm) 18 Thickness of Door in mm (± 1 mm) 18 Type of Doors Hinged doors of equal width hung with auto closing hinges of 0 cranking overlay type ,Sliding Type Doors

Providing, supplying and placing in position News Paper / Magazine Stand of Overall Dimensions shall be 900mm(W)x450mm(D)x1850mm(H). Rigid Knockdown construction ,Panels shall be made from CRCA 0.8 mm thick. The front frame shall be made from CRCA 0.8 mm thick . CRCA D grade as per IS 513 . Each unit shall be 5 Retractable Display Metal Tray fixed at an angle for easy viewing. Display tray shall be suitable for fullscape size magazines,periodicals, aesthetically appealing metal tray at an angle for easy viewing . Receding facility to access the storage behind . Sliding on plastic rollers . Behind storage shelving each of 5 level has a behind storage shelf . Uniformly Distributed Load capacity per each shelf is 40 kg . Leveler shall be screw type with hex plastic base and finish shall be epoxy polyester powder coated to the thickness of 50 microns .

Supplying & Placing Steel Almirah, 2 Doors, 4 Adjustable Shelf, Thickness 0.8mm W900 X D 450 X H1830Geeken Technical specification of Almirah steel Generally conforming to BIS specification IS: 3312:2021 (with latest amendment) Type of Almirah steel Almirah Steel shelving cabinets Number of door 2 Number of drawers required No Drawer Number of shelves 4 Colour of finish As per Buyer’s Requirement (to be indicated during bid creation) Steel sheet material CRCA sheets conforming to grade CRI of IS 513(part-1):2016 (with latest amendment) Sheet rounds and flats Conforming to grade E250 of IS 2062 Almirah height(excluding the height of pedestal) ± 5 mm 1980 mm Almirah width ± 5 mm 900 mm Almirah depth ± 5 mm 450 mm Side sheet thickness 0.8 mm Back sheet thickness 0.8 mm Top sheet thickness 0.8 mm Bottom sheet thickness 1 mm Shelves sheet thickness 0.9 mm Shelves supporting bracket thickness 1.6 mm Hinges sheet thickness 1.25 mm(double folded) Hanging rod wall thickness N.A Mirror frame sheet thickness N.A Mirror frame border width N.A Width of stiffener N.A Stiffener sheet thickness N.A Number of glass sheet fixed N.A Handle size 12 cm Steel Almirah lock/locker lock Six lever lock Material of lock Brass and Steel finish Finish coat with enamels Conforming to IS:151 Powder coating Conforming to IS: 13871

Providing, supplying and placing steel almirah. The overall size of the Almirah shall be 900mm (W) X 450mm (D) X 1830mm (H). The Almirah shall be supplied with 2 nos. of glass door and 2 nos. of steel door with adjustable shelves. The door shall be operated with aesthetically appealing snap fit ABS plastic handle and concealed crank hinge. The glass shall be used 4mm thick clear. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength. The entire body panel, shelf shall be made of high yield strength 0.8mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. To protect the ball from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-60µ thick.

Supplying & Placing Lab Table Double Side with Reagent Shelf and Sink 3680(L) X 1540(D) X 900(H) Geeken Model Number LAB 7 or eq. CABINATE DESIGN Faciliting future equipment retrofits and full reconfigure without requiring and masore modification ti the structure with sink and water supply and drain pipe and fittings. Ground Clearance 25 mm amterial of frame Galvanized (zinc coated) GI steel sheet double skin pass Thickness of Frame 1.1 mm Cabinets body (casing material GI Sheet Side Cover 1.2 mm Hinges made up of SS 304 5 Digital Knuckle Butt Hinges Service Pipe Support L Type Support duly perforated , Service Pipe Support made up of 32 mm x 2 mm thick GI flats slotted at a perticular pitch epoxy coated, work yops Acid resistant granite 18 mm trhick colour of work top as per buyer's choise, worktop placed on 4 mm thick neoprene rubber stop back placed between table tops and table frame work with provided with one number of 3 module plate having 5/15 amps combined switch and 1 set of sockets all coplete with fitting as per engineer in charge.

Supplying & Placing Revolving Stool, Cushioned Top, Stainless Steel Structure, Height Adjustable (510mm - 690mm) Adjustable Height No Normal Height (mm) 510 Min. Height (mm) 510 Max. height (mm) 690 Stool Top base Thickness (mm) 1.6 Cushioning in the stool Top with Cushion No of Legs in the under structure 4 Foot rest Without Material of Top Stainless Steel Painting Powder coating Type of Stool Revolving Back rest Without

Supplying & Placing Dining/study Table, Powder Coated Pipe Frame, PLPB Edge Banded Top, 25 mm Thick, Size in mm - 1800 X 900 Shape of Table Rectangular Seating Capacity 6 Material of top Prelaminated board Material of understructure Powder Coated MS Material of top finish Mica Length of table ±10mm (Diameter in case of Round) 1800 mm Depth of table ±10mm 900 mm Thickness of top in mm (+/- 5%) 25 mm

Supplying & Placing Café Chair, Chrome Plated Pipe Frame, Leatherette Tapestry Chair Armrest Without Type of seat Ply Seat Cushion With Back Rest Cushion with Upholstery Leatherite Material of frame SS 304 Chair height (overall) ±10mm 880mm Backrest width ±10mm 425 Width of seat ±10mm 400 Depth of seat in mm (+/- 10 mm) 400 Height of seat in mm (+/- 5 mm) 400 Seat Finish Cushioned Exposed Wooden / Metal Parts Finish N.A

Supplying & Placing Steel Library Rack (Double Face), Thickness 0.8mm W940 X D600 X H2110 Type CLOSED FROM SIDES ONLY Number of Shelves/Compartments (Top / Ceiling Shelf - not to be counted) 4 Shelves Material 0.8 mm Thick MS Sheet Conforming to Commercial Quality CR-1, Grade 340 of IS 513 Depth in mm (±5 mm) 600 Width in mm (±5 mm) 915 Height in mm (±5 mm) 2000 Paint Powder coated

Supplying & Placing Drinking water palteform Approximate External Dimensions (WXDXH) 750 x 690 x 1420 mm Input Voltage 230 V AC (50 Hz) Power Rating (Max) 850 ± 10% Water Storage Tank Capacity 120 Litre Cooling Capacity 60 LPH Output Water Temperature 15°C±1°C Refrigerant HFC R 134 a Thermal Insulation for Storage Tank PUF No. of Faucets 3 Cold No. of Stages for Filter cum Purifier 7 Active Copper Zinc Booster Yes % of Purified Water Recovery 25% % Rejection of TDS 90% (Approx) Permeate (Purified Water) Production Capacity 50 LPH Storage Tank & Drain Tray Material SS 304 Outer Body Material rest CRCA Powder Coated Steel Front Panel SS 304 and Type of Product Construction Concealed Type of Installation Indoor Net Weight 92 Kg Operating Input Water Pressure 1.0 to 2.0 Kg/cm² Operating Temperature 10°C to 40°C Recommended Total Dissolved Solids in Input Water(TDS) 500 to 2000 ppm.(Max) Recommended Hardness in Input Water 300 ppm(Max) Recommended pH of Input Water 6.5 to 8.5 Allowable Chlorine Input Water 0.2 ppm (Max) Allowable Iron in Input Water 0.3 ppm (Max) Turbidity <5 NTU

Supplying & Placing Conference table in completely knock down conditions with an overall size 4500mm X 1500mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix, dowels, pins and brackets. The worktop shall have the combination of PLPB board and MDF board. The main top should be made up of back to back 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and the base top shall be made up of 25mm thick Medium density fibre-board with deco matt finish. The table top profile shall be boat like shape with round corners. The edges edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius and the base top shall be with half round post form with grooves. Single sided Flip-up box should be enclosed at table top that houses video, audio, data and power connection discretely. Wire carrier shall be provided below the table top for power connection made of 0.8mm thick high yield strength CRCA sheet of grade 'D' confirming to IS:513. The table shall be supported on particle board base gable end. The end wall of the table on the side and mid shall be topped by gable end. It should be made up of 36mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick Pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Add 18% GST

Add 1% Labour cess 1%

M/s Raj Construction

Tribeni Constructions ltd

Bidder Name

Tribeni Constructions ltd