SMART MAINTENANCE REPAIRS TO LEAKAGE SEEPAGE TANK CLEANING SUNKON PORTION ROOF TREATMENT IN OFFRS MD ACCN ADM OFFICES, MESSES VIP BLDGSN AND CERTAIN REPAIR AT ASCON NODES OF NSR IN THE AREA OF AGE B R I UNDER GE ARMY NO 1 JODHPUR

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed.

M&L 40 mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in flooring/hard standing laid in alternative bays using glass dividing strips including finishing cement concrete surface even and smooth without using extra cement complete all as specified & as directed. Note:- Glass dividing strip shall be measured & paid separately.

Supply only 38mm wide and 3mm thick glass dividing strip complete all as specified & directed

M&L PCC 1:4:8 type D-2 using 20mm graded crushed stone aggregate, as in sub base of floor incld. compaction properly & universal and laid to level, complete all as specified and directed.

M&L 50 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight in 2 mtr interval, complete all as specified and directed.

Dismantling, stone slab, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as directed.

M&L for 25 mm thick cement concrete 1:2:4, type B-0 (using 12.50 mm graded crushed stone aggregate), to receive floor finishes, complete all as specified & directed.

M&L for joint free non skid ceramic coloured tiles (premium quality) of size 6 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including M&L 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

All as per item No. 8.00 here-in-above, but size of tile exceeding 0.11 Sqm but n.exc. 0.18 sqm .

All as per item No. 8.00 here-in-above, but size of tile exceeding 0.18 Sqm but n.exc. 0.38 sqm .

M&L for glazed colour ceramic tiles (premium quality) of size 250X450X6-7mm / 300X450X6-7 mm, as in vertical surface such as i.e. dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including M&L 15mm thick backing coat in CM (1:6) complete all as specified and directed.

M&L for dark shade vitrified ceramic tiles, 10 mm thick (square/ rectagular) polished, area of each tiles not exceeding 0.36 sqm, (size & shape, shade and pattern as approved by GE), as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles, over & including M&L 15 mm thick screed bed in cement mortar 1:4, complete all as specified and directed.

All as per item No. 12.00 here-in-above, but as in skirting over & including M&L 10 mm thick rendering in CM 1:4 complete all as directed.

Taking down cement plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed.

M&L for 10 mm thick Rendering in CM 1:3 on fair faces of brick work or conc surfaces as in ceilings/chajja/facia & finished even & smooth w/o using extra cement, complete all as specified and as directed.

S&F wire netting galvanised steel wire cloth 0.9 mm nominal dia and 12 mm mesh lathing and fixed to ceiling including all laps, cutting and waste fixed with nails on ceiling complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished surface fair and even without using extra cement, complete all as specified and as directed.

M&L for 15 mm thick rendering in CM 1:6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished surface even and smooth without using extra cement, complete all as specified and as directed.

Racking out joints/ pointing to squared rubble or polygonal rubble un-coursed or brought up to courses masonry built in cement mortar or cement lime mortar, coursed or un-coursed in walls not less than 12mm deep, washing the joints, removing rubbish off the premises and keeping the surface to pointed or plastered wet for two days prior to re-pointing or plastering complete all as specified & directed.

M&L keyed pointing in cement mortar (1:3) to squared rubble masonry regular coursed or un coursed complete all as specified & directed.

Preparing new plastered or unplastered surfaces and applying with wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over & including M&L one coat of primer on walls complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and as directed.

M&L for preparation of new plastered or un-plastered surfaces of walls and applying two coats of colour wash over & including M&L one coat of white wash on walls, complete all as specified and as directed.

M&L for preparation of old decorated wall surfaces plastered or unplastered, by brooming down or steel wire brushing, scrapping down moulds, moss and efflorescent salts and trading oil & greasy spots, including cornices etc and applying one coat of white wash on wall, complete all as specified and directed.

M&L for preparation of old decorated ceiling surfaces including cornices pilasters by brooming down or steel wire brushing, scraping down,smoke shoot,moulds,moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash on ceiling, complete all as specified and directed.

M&L for preparation of old decorated wall surfaces plastered or unplastered, by brooming down or steel wire brushing, scrapping down moulds, moss and efflorescent salts and trading oil & greasy spots, including cornices etc and applying one coat of colour wash on wall, complete all as specified and directed.

Complete removal existing preparing old decorated plastered or un-plastered surfaces of wall, pillasters, cornices etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spot and washing down with water including complete.

M & L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over & including M&L single coat of pink primer complete all as specified and as directed.

M & L for preparation of old painted wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint of any tint complete all as specified and as directed .

M&L preparation of new or previously untreated steel surface of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over & including M&L single coat of red- oxide, zinc chrome primer complete all as specified and as directed.

All as per item No. 28.00 here-in-above, but steel surfaces.

Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area not exc 1.5 Sqm each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area exc 1.5 Sqm but not exceeding 4 Sqm each, complete all as directed.

Taking down shutters of any description area exceeding 1.0 Sqm but not exceeding 2 Sqm each complete all as specified and as directed.

M&L mild steel work as in door frame and similar work fixed with angle cleates, confirming to Fe 410 Grade E - 250 Quality A, complete all as specified and as directed.

M&L for framed brackets for cooler stand as shown in Drg No CEJZ/TD/72/2015 sheet1/1 of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') and used for step/stairs, complete all as specified and as directed.

M&L for rolled mild steel sections like angle, channel, flat, square etc as in framed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars ,barred iron doors; ladders ;framed balusters walk ways railings framed work of water tanks and similar work confirming to Fe-290Gde E-165 complete all as specified and as directed.

M &L for fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet & with frame 1.25 MM thick bent to shape incl two coats of syn enamel paint on int surfaces & two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc complete all as per drg no CEBZ/TD/12/2008 sht 1/3 to 3/3,complete all as specified and as directed.

M&L for 35mm thick factory made 2nd class hard wood glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a) complete all as specified and directed.

S&F35 mm thick factory made second class hard wood plain framed panelled shutter (Two panel) with lock rail and pannel of 9 mm thicks BWP commercial ply or 12mm veneered particle board with commercial veneered on both faces the size of rails and style as per IS-1003 (Part-I) kiln seasond and chemicadly pressue treated all as specified and directed.

M&L factory Made flush shutters, 35 mm thick solid core with particle board core construction as per IS 2202(part-I, 1999) . The stiles & rails shall be with out any joint and made with non- coniferous timber hard wood (Hillock/ Mirantee/ Bosum/ Benteak) with moisture content not less than 12% as per IS. The face panel comprising of ply wood or cross band and face veneers shall be glued by hot pressed process. The over all finished thickness of face panel shall not be less than 35mm while the thickness face veneer shall not be less than 0.6 mm complete all as specified and directed.

S/F of factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of MS tubes for top & bottom rail. MS frame shall be covered with heat moulded plain color pvc ‘C’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain color pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted to the MS Frame/sealed to the stiles & rails with suitable PVC sheet beading, and joined 30mm thick (style) consisting of frame made of MS tubes for top & bottom rail. MS frame shall be covered with heat moulded plain color pvc ‘C’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain color pvc sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail paneling of plain colour PVC sheet to be fitted the MS Frame/sealed to the stiles & rail with suitable PVC sheet beading, and joined together with solvent cement, all as specified.

M/L for solid PVC door frame of size 50x47mm made out of 5mm thick pvc sheet reinforced with MS square tube all as specified.

Taking down steel window/ventilator complete.

S&F factory made box type windows (steel) (BWM) with side hung shutter including cooler opening as shown in Drg No CEJZ/TD/20 sheet1/3 to 3/3 complete with glazing bars, dovetailed or welded, complete all as specified and as directed. Note : Both shutter (wherever applicable) will be jointed internally with flat iron of size 40 x 4mm and quoted rate deemed to include the cost component of the same.

All as per item No. 45.00 here-in-above, but without glazing bars, complete all as specified and directed.

All as per item No. 45.00 here-in-above, but without cooler opening, complete all as specified and directed.

All as per item No. 46.00 here-in-above, but without cooler opening, complete all as specified and directed.

S&F of Box type steel ventilator with top hung shutter including hinges with steel handle, and steel peg stay, complete with glazing bars, complete all as specified and as directed.

All as per item No. 49.00 here-in-above, but without glazing bars, complete all as specified and directed.

Repair to steel window including taking down, replacement of unserviceable hinging devive box type , handles, making them in serviceable condition and re-fixing in same opening including making soffits and jambs in CM 1:4 complete all as directed.

S&F of stainless steel tower bolt 200 mm long complete all as specified and directed.

S&F stainless steel handle of size 150mm long complete all as specified and directed.

S& F of stainless steel sliding door bolt woth hasp and stalpe (bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 16mm dia and 300mm long, complete all as specified and directed.

S & F butt hinges 100 mm long,extruded aluminium alloy with mild steel hinge pin anodised type C- 21 for PVC door complete all as specified and directed.

S & F of stainless steel butt hinges 100 mm size complete all as specified and directed.

S & F in repair of mild steel butt hinges 100 mm size including welding fixed to frame complete all as specified and directed.

S & F 100mm size single action door spring hinge complete all as specified and directed.

S & F in repair 100mm size single action door spring hinge including welding fixed to framecomplete all as specified and directed.

S & F floor door stopper of alluminium alloy body and toungue anodised with hard drawn steel spring 140mm long complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame incld punching or drilling out old glazing pins/ spring clips and provding and fixing new ones, complete all as specified and as directed.

S&F for 4 mm thick figurred, pin headed glass ordinary quality & glazing with oil putty in square n exc 0.50sqm ineach pane, complete all as specified and as directed by Engr-in-Charge.

S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.00 mm complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.00 mm complete all as specified and directed.

S&F in repiar SS wire cloth 0.56mm nominal dia of wire and average width of aperature 1.00 mm as in necessary weilding complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in coping/ benching, DPC, pier caps, bed blocks, for hold fast etc., including mixing with WPC and necessary form work, complete all as specified and as directed. Note:- WPC shall be measured and paid separately.

S&F flat iron for hold fast and similar work confirming to Fe-290 Gde-E-165 fixed with welding and necessary item, complete all as specified and as directed.

S&F in repair shelf of PTMT fixed with and including chromium plated brass screws and wooden cleats (Min weight 300 gms), complete all as specified and as directed.

S&F in replacement decorative type curtain rod stainless steel finish of pipe 22 to 25mm dia with best quality knob metal with double fitting type including stainless steel brackets fixed to walls complete with two nos decorative stainless steel knobs at each end, complete all as specified and as directed.

S&F in repair soap dish of PTMT fixed with screws complete all as specified and directed.

S&F in repair PTMT towel rail 450 mm long fiexd to wall with chromium plated brass screws and woodn cleats Min weight 170gms complete all as spcified and directed.

S&F in repair MS chromium plated peg set of five fixing with wall complete all as specified and directed.

S & F in repairs stainless steel kitchen sink without drainage board, made of stainless steel 1 mm thick, with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe, over all size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

S & F in replacement white vitreous china squatting pan "Orissa pattern" of size 580 mm X 440 mm with integral foot rests and PVC 'P' or 'S' trap, including M&L brackets, flush HDPE pipe of 32 mm dia and PVC connection 15mm size, 450 mm long with PTMT nuts & fixing arrangement of cistern, including provision of cement concrete bedding 1:5:10 type E2 complete all as specified and as directed.

S&F in replacement vitreous ware wash down water closet [Pedestal Pattern], white [ETWC] including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap connecting to drain pipe and flushing pipe etc., complete all as specified and directed.

S & F for vitreous china ware wash hand basin, white, flat back of size 400 mm X 550 mm including 32 mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe,PVC connection15mm size with PTMT nuts of length 300mm long complete all as specified and as directed.

S & F in repair 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S &F in repair 20 mm dia stop valves, cast copper alloy with screw down high pressure with crutch or butter fly handle screw both ends for iron pipe or for union & fixed of 20mm bore pipe all as specified specified.

S &F in repair 25 mm dia stop valves, cast copper alloy with screw down high pressure with crutch or butter fly handle screw both ends for iron pipe or for union & fixed of 25mm bore pipe all as specified specified.

S&F in replacement angular stop valves, chromium plated, brass (ISI marked) screwed down high pressure fancy type screwed both ends for 15mm bore of iron pipe or union, complete all as specified and as directed.

S& F as in repairs 15 mm dia stop cock regular body with adujstable wall flange with chromium plated brass, fancy type, with (concealed type) all as specified.

S&F in replacement of bib cock with flange 15mm dia, chromium plated, brass, fancy type, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F in replacement 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia complete all as specified and as directed.

Taking down existing flushing cistern and replace of internal kit washer/syphon replaced with ISI marked as per direction of Engr-in-Charge and make the same in serviceable condition complete all as specified. Note :- The internal flushing kit/syphon use as per the existing make.

S&F in replacement Rotational moulded polythene water storage tanks of 500 ltrs capacity, white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I with PTMT ball valve heigh pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms including dismantling old tanks complete all as specified and as directed.

S & F in repair 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

M&L 50 mm thick plain cement concrete, 1:2:4 type B0 using 12.5mm graded stone aggreage, as in coved fillets of radius provided at junction of roof and parapet / vertical surfaces, padding concrete to achieve slope as required , platform for water tank on roof slab etc., including necessary form work complete all as specified and directed.

Demolition of cement concrete reinforced in manhole covers in any position not other wise specifically provided complete all as specified and as directed.

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in landings, cover slabs (for man holes etc) chullah hoods,chajjas,water troughs,shelves and similar articles with plain faces complete all as specified and as directed .

M&L for TMT bars 6 to 8mm dia and over, cut to length , bent to shape required including cranking, bending & binding with MS wire (annealed ) not less than 0.9mm dia or securing with clips, as in stirrups also & all as specified.

M&L stone slab 5 cm thick dressed true and square, in one length not less than 60cm and n. exc 200cm in copings, window cills, chajjas, sunshades, etc., punched dressed on exposed faces and self faced on the embedded unexposed beds and joints, exposed edges rounded or chamfered as directed, set, jointed and pointed in cement mortar 1:4 complete all as specified and as directed

M&L for 20 to 22 mm thick (telephone black shade) granite stone, as in WHB counter top, machine cut, (table rubbed and polished) best quality as per sample, over & including 20 mm thick screeding in CM1:3 including rounding & double mouldlng with jointless finish of the edges, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed.

S & F continuous (PIANO) hinges, mild steel, bright finish or electrogalvanised, 30 mm width of flaps (when open), complete all as specified and as directed.

S & F in repair 18 / 19 mm thick pre-laminated particle board exterior grade, pre-laminated one side with decorative choice of lamination and other side balancing white lamination as in cup board shutter fixed with screw teak wood beading all round / exposed faces, complete all as specified and as directed.

S & F in repair 32 mm bore low density polythene pipe (LDPE) of pressure rating 6 kgf / Sqcm for WHB and sink complete all as specified and directed.

S & F in repair 40 mm bore low density polythene pipe (LDPE) of pressure rating 6 kgf / Sqcm for WHB and sink complete all as specified and directed.

M& L for precast cement concrete Type B-0 1:2:4 (12.50mm graded aggregate) as in louvres and jallies, cement grill any type model of Zafri 25/40mm thick (measured solid), set in cement mortar 1:4 fixed with PCC post, incld. all mouldings complete all as specified and directed.

S & F Precast cement concrete1:2:4, type B-0 by using 12.5mm graded stone aggregate as in pillars to provide support of RCC jallies & similar work, jointed with neat cement slurry complete all as specified and as directed.

S&F in replacement Rotational moulded polythene water storage tanks of 1000 ltrs capacity, white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I with PTMT ball valve heigh pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms including dismantling old tanks complete all as specified and as directed.

S&F in repair high quality looking mirror 5mm thick with fancy type beading fixed to wall with chromium plated screw area n exc 2.0 sqm, complete all as specified and as directed

S&F in repairs EWC (one piece) of size 390X645X845 mm, Rimless bowl with cistern for coupled WC with UF soft close slim seat cover, hinges conversion bend, dual flush cistern fitting, fixing accessories and accessories set complete set with S trap, complete all as specified and as directed

S & F for vitreous china ware wash hand basin, counter top, white, of size 390 X 525 mm including 32 mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe,PVC connection15mm size with PTMT nuts of length 300mm long complete all as specified and as directed.

S&F in repair of chromium plated, brass, fancy type, shower rose 100mm dia round/square shape complete all as specified and directed complete all as specified and directed.

S&F 15mm bore CP brass, central hole basin mixture pop um waste system with 450 mm long copper pipe and brass, fancy type, nuts ISI Marked sitable for over head counter, complete all as specified and directed.

S&F in replacement CP brass fancy type wall mixer with telephonic shower arrangement ,connecting legs and wall flanges, including overhead shower, crutch and telephone shower complete all as specified and as directed.

S & F in repair 15 mm bore pillar taps, brass, with capstan heads, chromium plated, fancy type, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in replacement of two way bib cock with flange 15mm dia, chromium plated, brass, fancy type, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F bath Cabinet with Mirror approved type standard size 300x450mm all as specified and directed.

S&F stainless steel plate rack of size 1200mm X 1000mm X 200mm of approved pattern made out of stainless steel sheet 1 mm thick with round 8mm dia rods complete all as specified and directed.

M&L for rolled mild steel confirming Fe-290 (Gde E-165) in door or gates of angle (35x35x5 mm) or other section with gusset plate, rail braces etc complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (inclding of steel, sheeting or other covering ) and hanging also fastening and fixing complete all as specified and as directed.

Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges as in roof covering complete.Note:- Opening of existing wind tie where required for taking down of AC sheet is included in the rate quoted against this item.

S & F Fibre glass reinforced translucent 2 mm thick corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof ,wall etc complete all as specified and as directed.

M&L for prepainted Galvalume Aluminium Zinc Coating GI based corrugated Steel Sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and as directed .

Taking up or down 25mm bore steel tubing and connections including cleaning for refixing or credited to contractor complete all as specified and directed.

All as per item No 116.00 here-in-above, but size of pipe 20 mm bore.

All as per item No 116.00 here-in-above, but size of pipe 15 mm bore.

Refixing old GI water tubing of 25 mm bore, medium grade including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

All as per item No 120.00 here-in-above, but size of pipe 20 mm bore.

All as per item No 120.00 here-in-above, but size of pipe 15 mm bore including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc., complete all as specified and as directed.

S&F of water GI tubing medium grade, galvanized, with all fittings fixed to wall, ceilings or laid n floors, complete all as specified and as directed. (a) 25 mm bore,

All as per item No 122.00 here-in-above, but size of pipe 20 mm bore.

All as per item No 122.00 here-in-above, but size of pipe 15 mm bore including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc., complete all as specified and as directed.

Demolition of cement concrete as removing existing roof treatment and preparing surfaces to the entire satisfaction of Engr-in Charge /GE including taking down existing plaster, padding,cleaning of all foreign material such as grass roots dust etc and roughening the concrete surfaces by wire brushes and washing down to remove dust etc . flushing at junction of parapets complete and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed.

M&L for neat cement slurry @ 3.00 kg/Sqm and screeding / bedding layer of 10 mm thick in CM 1:3 mixed with water proofing compound as per manufacturer instructions over the RCC roof slab for laying of water proofing treatment including providing the following as roof treatment complete all as specified and as directed : - (a) FIRST COURSE: Applying a coat of bituminous primer @ 0.4 litre / Sqm manufactured by the same agency that of APP with a density 0.87 to 0.89 Kg/litre at 25 degree celsius on prepared plastered surfaces. (b) SECOND COURSE: Applying one coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.20 Kg/Sqm (c) THIRD COURSE : Provide a layer of APP modified polymeric membrane centre core of 100mm micron HMHDPE, outer film 20 micron each, thickness 3.00mm having weight not less than 3.00 Kg/Sqm, mineral gravel finish on top, using torch application method with minimum 10cm side lap and 15cm end lap complete . (d) FOURTH COURSE : Applying one coat of bonding material using blown type bitumen conforming to IS- 702 grade 85/25 @ 1.20 Kg/Sqm. (e) FIFTH COURSE : 40 mm thick plain cement concrete 1:2:4 (using 20 mm stone crushed aggregate) as in roof padding, including WPC as per manufacturer instruction. NOTE :- 1. A Information Tablet will be put up in the front side wall of the buildings where this work will be done. All building/structure shall be provided with plaque (tablet) furnishing the information as per PS clause, in plaster engraving in and painted as directed by GE 2.WPC shall be measured and paid separately under respective item.

Supply only Integral water proofing compund

Complete removal of folliage/vegitation growth on building and in over accessible/ non accessible roof ,chajjas. Wall and simillar surfaces etc. and making good the surfaces, area of each job not exceeding 1.00 Sqm and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed. (Note:- Appx height of the buildings 7.00Mtrs)

M&L for plain cement concrete 1:2:4, type B-0 (using 12.50mm graded crushed stone aggregate), as in roof padding over roof for making good depression / undulation to make the existing as filling in depression of roof slab, complete all as specified & directed.

M&L plain cement concrete (1:2:4) type B-1using 20mm graded crushed stone aggregate as in roof kerbs or mud steps, weathering, rounded or chamfered on edge, fixing of holdfast etc complete all as specified & directed

M&L for PCC (1:5:10) lean cement concrete type E2 using 40 mm graded stone aggregate in mass concrete after carrying out satisfactory testing of CI pipe/ PVC pipe joints and slab /wall by filling water for 72 hours. Sunken portion of Nahani/ floor trap and pipe joints shall be embedded in PCC 1:3:6 type C1 complete all as per specidfied and directed.

S & F 32 mm bore light grade galvanised tubing, provided 30 cm beyond wall surface between to drain out if any leakage, the mouth of GI pipe shall have greval to avoid chocking, top of sunken portion of RCC slab to be finished such that its slope towards spout, complete all as per specidfied and directed.

M&L for cleaning and removing all scale dirt etc from mouths of circulating pipes of water tanks of capacity up to 500 litres complete all as specified and as directed.

M&L for cleaning and removing all scale dirt etc from mouths of circulating pipes of water tanks of capacity exceeding 500 litres and not exceeding 1000 litres complete all as specified and as directed.

Disconnecting existing tanks setting aside [or lowering if required] for repairs,cleaning etc., and hoisting if required reconnecting and refixing in position of water tanks of capacity up to 500 litres complete all as specified and as directed.

Disconnecting existing tanks setting aside [or lowering if required] for repairs,cleaning etc., and hoisting if required reconnecting and refixing in position of water tanks of capacity exceeding 500 litres and not exceeding 1000 litres complete all as specified and as directed.

M&L Jodhpur stone slab tile 20-25mm thick machine cut, factory polished, pink colour, as in wall cladding, and like bedded and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the shade of granite stone over & including 10 mm thick screeding in CM1:3 complete all as specified and directed.

Note:- All painting work shall be done by authorized applicator and mechnical means (spray machine) only.

M/S SUMAN ENTERPRISES

M/S KARNINCONSTRUCTION COMPANY