SPL REPAIR OF BLDG NO. T-13 AND TOILET BLOCK OF APS KANDRORI, SPL REPAIR OF ROOFING IN LIEU OF ASBESTOS SHEET IN SCHOOL AND LIVING ACCN AT KANDRORI/ MIRTHAL BLDG NO. T-112, T-256 AND T-291, PROVN OF TOILET BLOCK WITH 02 WC, 04 WASH HAND BASINS AND 4

Amount

Surface dressing n. exc 15 cm deep in soft and loose soil, complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundations etc. n.exc 10 sqm on plan and getting out in any type of soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm, complete all as specified and directed.

Removing excavated materials( soil) obtained from excavation to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point, complete all as specified and directed.

Surface excavation n exc 30 cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40mm graded aggregate) in foundation, filling, mass concrete, complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, rafts raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or batter, finished rough surfaces of concrete, complete all as specified and directed.

M&L for Formwork to sides of square or rectangular pillars, posts, struts, columns etc., complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams,, splays between floor and beams etc., complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), complete all as specified and directed.

M&L for Formwork to edges of concrete flats , window cills, floor and roofs n exc 20cm wide, complete all as specified and directed.

M&L TMT bars 5mm dia and over upto and incl 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including bending, cranking etc. and binding with and including MS wire (annealed) not less than 0.9mm dia, complete all as specified & directed.

M&L TMT bars 10mm dia and over cut to length, bent to shape required including bending, cranking etc. and binding with and including MS wire (annealed) not less than 0.9mm dia, complete all as specified & directed.

M&L for Reinforced cement concrete M-25 as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed.

M&L for Reinforced cement concrete M-25 as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for RCC M-25 as in columns, pillars etc., complete all as specified and directed.

M&L for 25mm thick Damp proof course in cement concrete 1:2:4, type B-0, to horizontal or vertical surfaces including necessary formwork all as specified and directed.

M&L for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M&L for rendering 15 mm thick in cm 1:4 on other than faces of block masonry /brick work surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M&L for Rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for Rendering 5mm thick in cement mortar 1:3 on ceiling of brick work or concrete surfaces finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick plain cement concrete type C-2 1:3:6 (using 40mm graded crushed stone aggregate) as in flooring/sub base, complete all as specified and directed.

M&L for cement concrete type C-1, 1:3:6 (using 20mm graded aggregate) as in plinth protection 75mm thick finished even and fair incl making joints at every 2.5m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight, complete all as specified.

M&L for preparation of new plastered surfaces of wall including cornices plasters and applying two coats of cement base paint over a coat of white wash on newly plastered surface of wall and curing after applying each coat, complete all as specified & directed by Engr-in-Charge.

M&L for preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and directed.

M&L for broken stone or boulder hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and directed.

M&L for liquid water proofing treatment to RCC roof slab incld dismantling of existing treatment of any description in following procedure : (a) Laying 10mm thick rendering in Cement mortar 1:4 mixed with WPC 3% by weight of cement on fair faces of concrete roof surfaces , finished even and fair to receive treatment on roof Complete (b) Applying first coat fiber reinforced elastomeric liquid water proofing membrane formulated with PU hybrid polymers and reinforcing acrylic fibers with sun reflective index (SRI) of 100-110, having minimum elongation of 350%, tensile strength 2.9 Mpa and shall have reack bridging ability upto 2.5mm and shall resist 10 bars of hydrostatic pressure reduce surface temperature upto 10 degree celsius with 3.3% dilution as priming coat (c) laying of fiber mesh 0.3mm thickness weave in leno pattern having weight 4.5 gm/ Sqm and pasting it properly with overlap of 50mm and allow it to dry (d) Applying second coat undiluted @ 0.45 ltr/ sqm as directed by Engr-in-Charge (e) Applying third and final coat undiluted @ 0.45 ltr/ sqm as directed by Engr-in-Charge. (The rate includes for filling cracks in existing roof with cement putty using suitable bonding agent (shalcrate 42) before laying cement plaster)

Supply only water proofing compound, complete all as specified and directed.

S&F mild steel, chromium plated Soap Dish fixed with and incl CP screws all as specified and directed.

S&F of 110mm bore, PVC (SWR) 'S' or 'P' trap complete all as specified and directed.

S&F of 75mm bore, PVC (SWR) floor trap complete all as specified and directed.

S&F in repair 32mm bore 60cm long with coupling corrugated PVC waste pipe, complete all as specified and directed.

S&F of 75mm bore, PVC rainwater (SWR) drainage pipes single socketed, in any length with rubber ring joints, fixed to walls with sufficient number of Iron stack clamp complete all as specified and directed.

S&F, 110mm bore, PVC rainwater (SWR) drainage pipes single socketed, in any length with rubber ring joints, fixed to walls with sufficient number of Iron stack clamp complete all as specified and directed.

S&F grating round 100mm size of PTMT (minimum weight 25gms), complete all as specified and directed.

M&L for Providing precast cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) louvers and jallies, 40mm thick (measured solid), including all mouldings but excluding frame, set in CM 1:4 complete all as specified and directed.

S&F 150mm long aluminium, anodized barrel tower bolts of extruded section ISI marked, complete all as specified and directed.

S&F 100mm long butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11, complete all as specified and directed including necessary welding if required.

S&F bib taps, long body, fancy type, chromium plated, cast copper alloy ISI marked with crutch or butter fly handle high pressure screwed down screwed for iron pipe of 15mm bore, complete all as specified and directed.

S&F in repair bib taps, long body, fancy type, chromium plated, cast copper alloy ISI marked with crutch or butter fly handle high pressure screwed down screwed for iron pipe of 15mm bore, complete all as specified and directed.

S&F 15mm bore Angle valve fancy type chromium plated with long shank and cup (concealed type) ISI marked with crutch or butter fly handle high pressure screwed both ends for iron pipe or for union and fixed complete all as specified and directed.

S&F 15mm bore Angle valve fancy type chromium plated ISI marked with crutch or butter fly handle high pressure screwed both ends for iron pipe or for union and fixed complete all as specified and directed.

S&F Hand Shower (Health Faucet) with 8 mm dia,1.2 m long Flexible Tube Chrome Finish & Wall Hook for Water closet complete all as specified and directed.

S&F vitreous china wash hand basin oval shape any size including cutting for and pining in ends of brackets or erecting stand, waste coupling and PVC waste pipe, 32mm dia to be fixed in MS brackets complete all as specified.

M&L for 18- 20 mm thick Granite (table rubbed and polished) of any type work on cooking platform and like in cement mortar (1:4) including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

S&F Vitreous China wash down water closet pan (Pedestal pattern) including P or S trap, fixing bolts & connecting to drain pipe including plastic seat cover with flat bottom cover and mild steel chromium plated hinging device and connection to flush pipe, anti symphonic pipe complete, all as specified and directed.

M&L Glazed ceramic coloured tiles of size 450 x 350 x 7mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar 1:4, complete all as specified and directed.

M&L for Non skid ceramic colour tiles 7 to 8 mm thick (sq/ rect) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F 10 litres PVC low level flushing cistern( white colour) syphonic action type with inlet ball valve float and push type handle including bracket, PVC 32mm dia flush pipe with coupling and fixed complete all as specified and directed.

S&F in repair 10 litres PVC low level flushing cistern( white colour) syphonic action type with inlet ball valve float and push type handle including bracket, PVC 32mm dia flush pipe with coupling and fixed complete all as specified and directed.

S&F 15mm bore GI tubing medium grade galvanized ISI marked with all fittings, fixed on walls and ceiling or laid in floors as required complete all as specified and directed.

S&F 20mm bore GI tubing medium grade galvanized ISI marked with all fittings, fixed on walls and ceiling or laid in floors as required complete all as specified and directed.

S&F stop valve 20 mm dia cast copper alloy screwed on high pressure with crutch or butterfly handle screwed bolts ends, for iron pipe or for union and fixed complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top hoisted fixed in position all as specified in SSR part-I, capacity of tank 500 litre incl inlet and outlet connection 20mm dia and 15mm dia GI pipes medium grade respectively 20mm GI pipe medium grade over flow pipe 15cm long and PTMT valve 20mm high pressure with polyethylene float and fly nuts complete all as specified and directed.

S&F of UPVC underground drawings pipe (UDS) type 'B' 160mm dia with wall thickness 4mm (min) and pressured 4 KN /Mtr Sq jointed in cement solvent complete including providing 100 mm thick cement concrete (1:4:8) type D-2 using 40mm graded crushed stone agg as in bed for 160mm bore pipes incl packing under and huaunching against the sides of pipes after they are laid tested including necessary excavation in trenches complete all as specified and directed .

S&F Vitreous china urinal half stall complete incl providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and incl 60mm long brass screws, pointing around urinal in back in cement; fixing automatic cistern with brackets, flush pipe, grating and union for discharge pipe, complete all as specified and directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (Minimum weight 60gms) complete all as specified and directed.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm prelam PVC sheet used instead of Plain colour PVC sheet and edges will be painted to match with prelam sheet reinforced with MS Square tube, supplying & fixing in opening as per specification and drawing. Note : Door frame shall be water proof, termite proof, elegant and should have excellent screw holding strength to fix hinges and hold doors properly for long life.

S&F Factory made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles) with 5 mm thick moulded prelam PVC sheet on the front face and 5 mm prelam PVC sheet on back face, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms), complete all as specified and directed.

M&L for septic tank for 50 usres designated to carry sewage and sludge water, including excavation in any type of soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC Slab covers including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame Vent shaft and sludge chambers etc, complete all as specified, shown on drawings and directed.

M&L for Chequered cement concrete coloured tiles 300mm x 300 mm x 25 mm thick set and jointed, pointed in neat cement slurry with grey cement and no pigment as in floor, Screed bed or bedding layer of 15 mm thick CM (1:6) as in floor, complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in copings, bed plates including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed

S&F GI tubing medium grade Galvanized of size 25 mm bore laid in trenches or ground/ in wall surfaces with and including all fitting complete all as specified and directed.

M&L for cutting existing GI/CI pipe line of size 40/25 mm dia pipe making new connection for GI pipe including short pieces , inserting tees, bends ,sockets, union etc with existing water line, complete all as specified and directed

S&F stop valve 25 mm dia cast copper alloy screwed on high pressure with crutch or butterfly handle screwed bolts ends, for iron pipe or for union and fixed complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F Prepainted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength 550 Mpa as in roof covering/cladding to walls, fixed with self taping screws complete all as specified and directed.

S&F pre painted galvalume aluminum zinc coated GI based plain steel sheeting 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to walls, fixed with self taping screws complete all as specified and directed.

S&F roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee angle, channel or flat sections) including distance pieces, cleats etc Fe 410-W (Gde E-250) complete all as specified and directed.

Demolition of brick work stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc, complete all as specified and directed.

M&L for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4, complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces any description including raking out joints hacking for key scrubbing down with water complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying 1mm thick wall care putty and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

M&L for applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/L and UV resistance as per IS 15489:2004 alkali and fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 L/10 Sqm and including priming coat of exterior primer applied @ 0.90L/10 Sqm over new surfaces complete all as specified and directed by Engr-in-Charge. Note : - Tint/Shade shall be approved by Engr-in-Charge.

M&L for washing rubbing down and scrapping of distempered and painted surfaces and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/L and UC resistance as per IS 15489:2004 alkali and fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 L/10 Sqm and including priming coat of exterior primer applied @ 0.90L/10 Sqm over old plastered surfaces complete all as specified and directed by Engr-in-Charge. Note : - Tint/Shade shall be approved by Engr-in-Charge.

S&F Mild steel framed work such as grills, gratings using square/round bar with ends of bars shoulders/welded drilling holes for fixing of guard bars, complete all as specified and directed.

S&F steel window/ventilator with tubular frame factory made of size 79mm x 39mm, 16 gauge rectangular tubular frame with side hung shutter both for glazed and wire gauge with glazing bars 12x3mm flat iron incl projecting type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100mm long and 10mm square bar grills complete, including two coats of synthetic enamel paint over one coat of red oxide primer all as specified & as shown on drg No CEPZ/TD-245/01 and 246/02 sheet ½ & 2/2 (excluding glass & wire guage).

S&F galvanized mild steel wire cloths 0.46mm nominal dia and average width of aperture 1.18mm & fixed with tint tacks or galvanized wire staples complete all as specified and directed.

S&F 3mm thick sheet glass ordinary and glazing with oil putty in square n exc 0.50 Sqm in each pane all as specified

M&L for complete removal of existing treatment internally surface of wall and applying min 1.0 mm thick wall care putty on the surfaces and making surface smooth and applying one coat of primer (as per manufacturer’s recommendations) on the surfaces and applying two coats of distemper oil emulsion without any brush marks on the surface in any tint including necessary scaffolding if required, all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

M&L for vitrified ceramic 10 mm thick light shade ( sq/ rect) polished, area of each tile not exceeding 0.36 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed in cement mortar 1:6 including dismantling of floor tiling incl cement mortar bedding (but not backing)removing serviceable tiles to a store and rubbish off premises, complete all as specified and directed.

Providing and fixing tiled false ceiling of size 595x595 mm incl of ceiling tiles in true horizontal level suspended on inter locking matrix 32 mm metal grid of hot dipped galvanized steel sections (galvanized @120gms per sqm both side incl) consisting of 3600mm long main "T" of size 24x25mm and 0.30mm thick and PPGI sheet wall angle of size 24x24mm and 0.40mm thick. Bottom exposed capping of width 24mm of all T sections shell be 0.25mm thick. PPGI wall angle is fixed align the perimeter of ceilings to walls, partition or columns etc. with rawl plug and wooden screws at 300mm denters. Main T runners are than suspended from ceiling using GI slotted cleats of size 27x37x25x1.6mm fixed to ceiling with 12mm dia and 38mm long dash fastners, 6 mm threaded rod with bolt for hanging arrangement of ceiling at max 1200 mm center to center along main T and not more than 150mm with slipped joints, the last hanger at the end of each main runner should not be greater than 600mm from adjacent wall. than 1200mm long cross T is interlocked between the main T at 600 mm center to center to form at grid 1200x600mm and than secondary cross of length 600mm is interlocked at middle of 1200x600mm grid to form grids of 600mmx600mm . cross T at the ends having length more than 600mm are to be supported independently. Finally PVC laminated with aluminium foil back board tiles of size 600x600x7 to 8mm thick tiles having light refectors of >=75% are placed in the grid incl dismantling of wall and ceiling board (fiber, pulp, insulation, etc.) or insulation boards/ slabs/ blanket, any thickness complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) not exceeding 1.50 Sqm each including taking out hold fast embedded in PCC, complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) exceeding 1.5 Sqm and n.exc 4 Sqm each, complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm and not exc 2.00 Sqm each, complete all as specified and directed.

S&F pressed steel frame for door made out of MS sheet 1.25mm thick of size 105mmx60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. including filling of concrete 1:3:6 type C-1 back of chowkats complete all as specified and directed.

S&F pressed steel frame for door made out of MS sheet 1.25mm thick of size 125mmx60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. including filling of concrete 1:3:6 type C-1 back of chowkats complete all as specified and directed.

S&F 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated, fitted to chowkats complete all as specified and directed.

S&F 35mm thick 2nd class hard wood in glazed and Skelton factory made shutters open rebated and prepared to receive glass/wire gauge etc. with sash bars edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass/wire mesh etc. sizes of members as per clause 8.20(a) of SSR Part-I complete all as specified and directed.

S&F 100mm long butt hinges medium weight cold rolled ISI marked mild steel complete all as specified and directed including necessary welding if required .

S&F 150mm extruded aluminium alloy handle fabricated anodized ISI marked, complete all as specified and directed.

S&F floor door stopper of overall length of cover plate 140mm or 150mm aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor complete all as specified and directed.

M&L for Preparation of new painted wooden surface of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for Preparation of new painted steel surface of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismantling boarding, any decription, fixed in any position with nails in cluding wooden fillets complete all as specified and directed.

S & F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. with Powder Coating (minimum thickness of powder coating 50 micron & min weight not less than 0.55 kg/Rm), complete all as specified and directed.

S & F Powder coated Anodised aluminium door shutters, aluminium section weighing not less than 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. including powder coating of any colour (Thickness or powder coating not less than 50 micron), complete all as specified and directed.

S&F cast iron body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and directed.

S&F in repair 20 mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed by Engr-in-charge.

S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted fixed in position all as specified in SSR part-I, capacity of tank 500 ltr incl inlet and outlet connection 20mm dia and 15mm dia GI pipes medium grade respectively 20mm GI pipe medium grade over flow pipe 15cm long and PTMT valve 20mm high pressure with polyethylene float and fly nuts including dismantling water tanks (capacity of tank exc. 250 ltr but n. exc. 500 ltr) and removing from site complete all as specified and directed.

S&F brass chromium plated tubular towel rail 20mm dia D type 60cm long between flanges, complete all as specified and directed.

Taking up or down GI pipe 15mm bore and connections, including cleaning for refixing or removal unserviceable pipe, complete all as specified and directed.

S&F Vitreous china urinal half stall complete incl providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and incl 60mm long brass screws, pointing around urinal in back in cement; fixing automatic cistern with brackets, flush pipe, grating and union for discharge pipe, complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section inc old wooden trusses, purlins, rafter of any description complete all as specified and directed.

Dismantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified and directed.

S&F in repair vitreous China squatting pan Orissa pattern size 580 x 440mm white with integral foot rest (excluding flushing cistern and flush pipe), including connection to trap, and to flushing pipe, anty syphonage pipe etc. and including 110mm bore PVC 'P' or 'S' trap complete incl making good to floor complete all as specifed and directed.

S&F pillar tap, cast copper alloy, chromium plated, fancy type with capstan heads screwed down high pressure with or without lettered hot or cold with long screwed, shanked and fly nuts screwed for iron pipe 15mm dia complete all as specified and directed.

S&F in repair vitreous china wash hand basin (flat back or angle back type) coloured of bowl size 550mmx400mm including waste and waste pipe PVC 32mm dia to be fixed over marble slabs or iron brackets complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block 60 mm thick (Factory made rubber moulded) with grey cement and pigment any shape and size conforming to IS-15658-2006 of 60mm thickness, M-35 Grade fixed all as specified and directed .

M&L for Sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

M&L 100mm thick plain cement concret type C-2 1:3:6 (using 40mm graded crushed stone aggregate) as in flooring/Sub base/Plinth protection complete all as spd and directed.

M&L for preparation of old plastered or unplastered surfaces of wall including cornices plasters by brooming down with steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent salt and trading oil & greasy spots etc. and applying two coats of oil bound distemper on wall, complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall including cornices plasters and applying two coats of oil bound distemper over a coat of primer on wall, complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed

Taking down distribution boards/wooden board ,switch fuse units,steel enclosures for MCB of any type and removing from site complete all as specified and directed.

Taking down existing unserviceable submain wiring of any size and making good the disturbed surface complete all as specified and directed.

M&L in replacement of Sub main wiring in two single run FRLS PVC insulated cable 6 Sqmm (Nominal dia) copper conductor (multistrand) and drawing in and including new PVC concealed non metallic conduit pipe ISI marked including one run 6 Sqmm multistranded copper conductor FRLS PVC green colour insulated unsheathed cable for earth continuity complete all as spd and directed.

M&L for modular point wiring with 1.5 sqmm (nominal area) PVC insulated FRLS and unsheathed multistranded copper conductor cable 1100 volts grade drawn through and including PVC rigid concealed conduit not less than 1.8 mm thick (ISI marked) with all accessories including suitable modular plate (Inner + Outer) and modular metalic boxes of suitable sizes including 1.5 sqmm PVC FRLS insulated unsheathed copper conductor multistranded cable for continuous earth conductor connected to common earth dolly, complete all as specified & directed for the following :- Note:- Proper colour coding is to be followed as per IS Specification.

All as per item No. 123.00 here-in-before but for one light point controlled by two switch 6 Amp SP, two way, 240 Volts.

All as per item No. 123.00 here-in-before but for one 5 pin 6 Amp socket outlet point on same board

All as per item No. 123.00 here-in-before but for one 5 pin 6 Amp socket outlet point on independent board controlled by one way switch SP, one way 6 Amp, 240 Volts

All as per item No 123.00 here-in-before but using 4.00 Sqmm (nominal area) multistranded copper conductor cable for geyser sheet metal plug socket outlet/metal plug top including 4.00 Sqmm size FRLSH PVC insulated and sheathed copper conductor cable as earth conductor (green colour) connected to common earth dolly for geyser on independent point complete all as specified and directed.

M&L in replacment for Modular switch 1 way 16A, 1 module 240 volts with polycarbonate body.

M&L in replacment for Modular socket 6A/16A, 2/3 pin combined, 2 module 240 Volts with polycarbonate body.

Supply, fixing, stringing and drawing submain wiring with 2 run of single core, 4 sqmm PVC insulated and unsheathed, multi stranded copper conductor cable FRLS using colour code for phase red and neutral black with and including 4 sqmm PVC insulated and unsheathed FRLS conductor multi stranded cable in green colour connected to common earth point and connected to earth dolly drawn through PVC rigid conduit 20 mm bore, heavy grade (ISI marked) with and including all accessories, fixed to surface / recessed for Geyser connection complete all as specified and directed.

S&F Modular switch 1 way 6A,1 module single, ( ISI marked) complete all as specified and directed.

S & F Socket, 6A - 2/3 pin combined 2 module, (ISI marked) complete all as specified and directed. .

S&F ceiling rose surface bakelite 65 x 50mm, three terminals ISI(Marked) all as specified and directed.

S&F LED lights fitting 1x 20W,minimum 3.5 feet 220V, AC decorative box type with driver, holder including LED tube light connecting up with flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F in replacement of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F exhaust fan, steel body AC single Phase. 230V of size 300 mm sweep with, blades, and frame and louvers complete all as specified and directed.

S & F SPN 8 way sheet metal enclosures factory made DB double door 230 V AC, 50 Hz AC 200 Amp rated bus bar complete all as specified and directed

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

S&F 240V, 10 KA 'B' curve miniaturecircuit breaker (MCB) of single poles and neutral current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cmX60cm X6mm thick buried directly in ground (earth plate not less than 2.25 mtr deep below the normal ground level) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth lead wire of 4.0mm dia by means of nuts bolts, washers, check nuts of iron or steel including PCC pits and RCC cover in PCC 1:2:4 (type B-1) and necessary earth work in any type of soil medium grade GI watering pipe 20 mm dia with funnel and wire mesh and 15mm bore GI pipe light grade protection pipe upto test point etc including excavation and charcoal, common salt surrounded with 15cm all around the plate all as specified and shown in EP-3 of SSR Part-I. all specified

Supply and laying in replacement of cable XLPE insulated armoured heavy duty electric cable with extruded insulation aluminium counductor, 1100 volts grade of cross sectional area 10 Sqmm 2 Core, complete all as specified and directed.

M & L for good quality dry sand cushioning to under ground electric cable on layer of 8 cm thick before laying the cable and second layer of 15 cm thick after laying the cable all as specified and directed. Note: Punned thickness of sand shall be measured.

Supply and laying sub class 'B' bricks of old size (230x115x75 mm) or of size locally available , laid along alignment of cable as protection to cable in trenches complete all as specified and directed by Engineer-in-Charge

S&F of 5 star rated BLDC (Brush less direct current motor) ceiling fan 230 volts, single phase of 1200 mm Sweep with regulator double ball bearing type with minimum air delivery 210 CFM with service value shall not less than 6.0 B.E.E including blade, down rod, canopy cover white colour etc, connecting 3 core flexible copper contuctor cable and dismantling of old unserviceable ceiling fans and depositing to MES store yard, complete all as specified and directed by Engr-in-Charge

S&F exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers and complete all as specified and directed.

Supply and fixing LED security light fittings 35 watt, IP 65 having pressure die cast aluminium alloy housing, prismatic polycarbonate cover complete including making connection with 3 core copper flexible cable of suitable size including galvanised iron pipe bracket 0.90 mtr long of 25 mm dia and fixing with bldg for fixing of street light fitting all as directed.

Supply and fixing in repair wall mounted fan 400mm sweep energy saving, copper wounded motor, three speed control complete suitable for operation on AC 220-240V AC, 50 Hz, PF >0.95, Air delivery approx 230cum/min including dismantling old unsv fan and depositing to MES store yard.

Note: (i) In case the tenderer quotes different rates for similar item then lowest rate shall only be applicable for payment and contractor shall not have any claim on this account. (ii) The Schedule of Credit amount shall be deducted from the total of this schedule (BoQ) to arrive at Contract Sum.

M/S BASOTRA BUILDERS (BID ID -3320076)

kay gee construction co (BID ID -3319577)

ADVAIT CONSTRUCTION CO (BID ID -3318851)

satpal and brothers (BID ID -3320083)

jagdambe traders (BID ID -3320207)

M/S OM SAI RAM BUILDERS (BID ID -3319989)

Jay Ann Construction Company (BID ID -3320250)

M/s. Jaswant Singh Govt Contractor (BID ID -3320108)