SPECIAL REPAIR OF BLDG NO 4/J/8 (165 TO 168) OF CERTAIN LOCATION AT BINNAGURI MIL STN UNDER GE (S) BINNAGURI

Amount

Dismantling Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified.

Supply and fix 0.50mm thick prepainted galvalume polyester coated (SMP coating) coloured metal roofing sheet trapezoidal profile having tensile strength 550Mpa as in roof covering/wall cladding fixed with self drilling screws with EPDM washer etc complete all as specified.

----Ditto--- all as per item No 2.00 above but for plain sheets.

Taking down tarfelt incl cement mortar bedding from roof surfaces and lowering and removing the same to a distance exc. 50m and n. exc. 100m incl roughening of old concrete surface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified.

M&L for 10mm thick screed bed or bedding layer in cement mortar (1:4) mixed with WPC over existing roof surfaces finished even and smooth without using extra cement complete all as specified and as directed

M&L for waterproofing Coating with polyurethane-based water proofing liquid membrane to be applied by brush with multi coats with minimum dry film thickness of 1mm and shall be cured by reaction with atmospheric moisture to give a tough elastomeric waterproof membrane complete all as specified and as directed. Note: The above treatment will be carried out by authorised applicator of approved firm/ company.

Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation boards any thickness including cover fillets and removal off the site.

Supply and fixing aluminium anodised snap grid false ceiling to support the boards / tiles with aluminium Tee section 35 mm x 25 mm x 1.40 mm cross Tee 23.50 mm x 23.50 mm x 1.40 mm and aluminium angle 25 mm x 25 mm x 1.40 mm as on edge / sides including hanging proper hanging arrangement with 4 mm dia anodized galvanised iron wire and adjuster complete as specified.

S&F 4mm thick (E-Boards) Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws in ceiling complete all as specified and as dirceted.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for non skid coloured joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but n. exc. 0.18 Sqm, in floors etc. set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed in whiter or coloured cement to match as in floor complete all as specified and directed.

M&L of coloured Non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floor etc set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed in whiter or coloured cement to match as in floor complete all as specified.

M&L for non skid coloured joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18Sqm but n. exc. 0.38 Sqm, vertical surfaces, in skirting etc. set and jointed in neat cement slurry and pointed in whiter or coloured cement to match as in floor complete all as specified and directed.

M&L for 10mm thick rendering in CM (1:4) as in vertical surfaces of wall as in skirting/dado etc complete all as specified and directed.

M & L for glazed ceramic colour tiles 300X 450 X 7 mm thick as on cup board vertical surface of wall such as skirting, dado, riser etc. in Bath, WC and Kitchen set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, Jambs, pillars, window cills, cooking platforms,corner shelf,Flat shelf and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 15 mm thick cement screed bed (1:4) including rounded the exposed surfaces of granite complete all as specified.

All as per item no 15 but as in skirting ( 12 to 15 mm thick) laid over 10 mm thick backing coat in cement mortar (1:3) complete all as specified and as directed.

Dismantling water tanks and removing from site of capacity 1000 ltrs.

Material and labour for hoisting and fixing rotational moulded polyethylene(double layer) water storage tanks 1000 lit capacity (Cylinderical vertical), ISI marked(IS-12701:1996) hoisted and fixed in position including inlet, oulet, over flow connection, ball valves etc complete all as specified.

M & L for Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) in water tank platforms,filling and mass concrete.

S&F in repair 20 mm dia PVC ball cock (PVC float valves) complete high pressure with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut.

Taking up or down GI 15mm bore pipe and connection including cleaning for refixing or removal from site as directed.

Taking up or down GI 20mm steel tubing and connections incl cleaning for refixing or removal to store.

S&F 15mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified and as directed.

S&F 20mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified and as directed.

Taking down cement plaster on wall & ceiling of any description including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed.

Material and labour rendering 20 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete work surfaces in two layers 10mm each layer and top 10mm layer mixed with integral water proofing compound all as per manufacturer's instruction and as specified. Make: 'Plastocrete Plus' of Sika/ 'Pidiproof LW' of Pidilite for water proofing compound. Note: WPC shall be measured and paid for separately as 'Supply only'.

Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed

M&L for applying two coats of Acrylic smooth exterior anti-fungal paint of shade as approved by GE over a coat of primer over and including 1mm thick (average thickness) finished putty surfaces of wall complete all as per the manufacturer's instructions and as specified. Note: Application of new finishes to be carried out mechanically by authorised applicator and as per the manufacturer's instructions for Smart Painting.

M&L 15mm thick rendering in cement mortar 1:6 on other than fair face of brick work or concrete surface finished fair and even (without using extra cement) complete all as specified and directed.

M&L for applying two coats acrylic-based distemper of shade as approved by GE over a coat of primer over and including 1mm thick (average thickness) finished putty surfaces of wall complete all as specified and as directed by the Eng-in-Charge and as per the manufacturer's instructions. Note: Application of new finishes to be carried out mechanically by authorised applicator and as per the manufacturer's instructions for Smart Painting.

M&L for rendering 5mm thick plastering in CM (1:3) on ceiling, soffits of slabs, chajjas, columns and beams etc and finished the plastered surface even and smooth without using extra cement.

M&L preparing newly plastered or unplastered surface of ceiling and applying three coats of white washing complete all as specified and directed.

Demolition of brick work built in cement mortar including quions, arches, pillars etc but excluding ashlar facing and dressed stone work including removal of rubbish off the site complete all as directed

M&L brickwork with sub class B bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete.

Supply and fixed in repairs sinks without drainage board made of stainless steel (SS304 grade)1mm thick sheet plugs, washers and waste pipe, including a pair of cantilever brackets embedded in wall with suitable size of PCC (1:3:6) type C-1 blocks and connecting union to pipe of overall size 510mm x 430mm x 203mm and bowl size 430mm x 380mm x 203mm all complete as specified. Make: Prayag Model No 1318D or equivalent as in the list of makes.

S&F in repair Vitreous China wash basin Pedestal pattern, white, flat back size 560 x 415 x 820 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipeincluding brackets, complete all as specified and as directed. Make: Prayag Model No ROLLIN or equivalent as in the list of makes.

S&F 15 mm fancy type pillar taps brass chromium plated screwed for iron pipe 15mm bore.

S&F of in repair vitreous china squatting pan "Orissa" pattern size 580x440mm white with integral foot rests(excluding flushing cistern and flush pipe) with 'P' or 'S" trap from or back inlet etc including connection to trap and flushing pipe and provision of lime concrete bedding complete all as specified.

S&F in repair 10 ltr capacity dual type PVC flushing cistern low level white colour incl PVC connection PVC flush pipe of reqd length complete all as specified and directed.

S&F in repairs Bib taps long body fancy type brass chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule all complete as specified.

S&F in repairs stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type) for 15mm bore pipe, screwed both ends including necessary fittings such as sockets for pipe or for union all complete as specified and as directed.

S&F in repair 20mm bore Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all complete as specified and as directed

S & F in repair 15mm bore PVC Connection with PTMT nut of length 600 mm complete all as specified and directed.

S&F in repair for brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed. Make: Prayag Model No GBA-131 or equivalent as in the list of makes.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chomium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F in repair of Stainless Steel soap dish of approximate size of 160x160x90mm fixed to the wall with SS screws complete all as specified and directed.

S&F in repair brass chromium plated towel ring complete all as specified and directed. Make: Prayag Model No GBA-111 or equivalent as in the list of makes.

S&F in repair 0.85mm thick stainless steel plate rack (SS304 grade) of size 31"x30"x10" complete all as specified. Make: Prayag Model No P-346 or equivalent as in the list of makes.

S&F in repair 75 mm dia swivel shower of CP with shower arm 150 mm size for fixing with 15 mm bore GI pipe complete all as specified and as directed

S& F in repair for 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

Taking down CI/PVC/AC soil pipe with fittings from wall, treches of any description including fittings complete all as specified and directed.

Supply and fix PVC (SWR) pipes 110mm dia type 'A', single socketed, conforming to IS-13592:1992 in any length with rubber ring joints laid in trenches or in floors complete all as specified.

S&F 110mm dia PVC bends of any radius with acess door complete all as specified and directed.

S&F 110mm dia PVC (SWR) branch piece single (single 'Y'/T) equal or unequal with acess door complete all as specified and directed.

S&F 110mm dia PVC SWR vent cowl complete all as specified and directed.

Supply and fix PVC (SWR) pipes 75mm dia type 'A', single socketed, conforming to IS-13592:1992 in any length with rubber ring joints laid in trenches or in floors complete all as specified.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and directed.

Taking down chowkat with shutter (without) taking of shutter from the frame, area exc 1.5 sqm but not exc 4.00 sqm.

S&F for pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 125 x60 mm complete all as specified and directed.

S&F for pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 105 x60 mm.

M & L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

S&F 35mm flush shutter, solid core construction, with block board core and plywood face panel, commercial type on both side etc complete all as specified and directed.

S&F of 35mm thick factory made Skeleton Shutter partly glazed and partly panelled i.e. upper panel will be wire mesh fitted externally in the clear space & lower panel will be plain colour PVC sheet 5mm thick complete all as specified and as directed.

S& F of 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F 100 mm butt hinges stainless steel complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section 200 mm long all as specified and as directed.

S&F aluminium handles 150mm size cast type anodised complete all as Specified.

S&F for sliding door bolt of 300mm long plate Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as Specified.

M&L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as Specified.

Taking down chowkat with shutter n. exc. 1.5sqm each complete all as specified and directed.

S&F Solid PVC door frame of size 50x47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplied and fixed incl fixing of hold fast as per specification and drawing complete all as Specified and as directed.

S&F Factory Made Solid PVC panel Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 4mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification with Wood free EPS complete all as Specified.

S&F 150 mm long Aluminium anodised barrel tower bolts complete all as specified and directed.

S&F in repair of 25mm dia curtain rod, chromium plated with fixing brackets etc. complete as specified and as directed.

M & L for providing & fixing factory made solid PVC cup board frame of size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5 mm thick prelam/plain colour PVC sheet reinforce with 19mm x 19mm MS square tube of 19 gauge thickness throughout the frame and metre cut at two corners and jointed with 2 nos of 150mm long brackets of 15mm x 15mm MS square tubes.The door frame shall be fixed to the wall using 100mm long MS screws through the frame by using PVC fasteners. A minium 4 nos of screws to be provided for each vertical memberand minium 2 nos of screws to be provided to the horizontal mmember etc.complete all as specified and dir by Engineer in charge incl dismantling of existing of cupboard.

M & L for providing & fixing factory made solid PVC cup board shutter (Flush type) of 24 mm thick made from co-extruded 3 layer regid PVC foam sheet (single extruded) with density not less than 600kg/cbm outer layer (.8-1mm) thick should be of rigid PVC with density of not less than 1400kg/cbm manufactured byan ISO 9001-2015 certfied company. Door should be water proof, turmite proof, fire retardant and having good screw holding capacity complete all as specified incl taking down the ext cupboard.

M&L in repair for providing and fixing factory made PVC shelf/partitation of required size consisting of 20mm thick solid PVC sandwich with 1mm thick plain PVC sheet on both sides suitably fixed in complete all as specified and directed.

S & F 75mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S & F in repair stainless steel wire cloth 0.36 nominal dia wire & average width of aperature 1.40 mm fixed with stainless steel wire staples complete all as specified and directed.

S&F Powder coated aluminium window sliding type three track (2 glazed & one gauze shutter ) aluminium sections weighing not less than 1.67kg/m for frame and 0.55 kg/m for shutter including necessary jointing cleats, glazing cleats, rubber packing , screws, handle, locking arrangement and 4 mm thick plain/tinted glass and aluminium mosquito proof gauge including taking down of old existing steel window and making good disturbed surface of wall complete all as specified and as directed.

S&F Powder coated aluminium louvered ventilators of size n exc 0.50 Sqm area with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazing cleats, rubber packing , anodised aluminium snap beading,screws, anodised aluminium fittings and 5.5mm thick tinted glass fixed in panels with suitable locking arrangements including taking down of old existing steel ventilator and making good disturbed surface of wall complete all as specified and as directed.

S&F Framed work such as grills,gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framedguard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

Demolition of cement concrete (unreinforced) in ground floors & paving n.exc. 15cm thick (below or above ground level) and removal of rubbish off the site complete all as directed.

M&L for 75mm thick PCC (1:3:6) type C-2 with using 40mm graded stone aggregates as in plinth protection laid in panels and finished even and fair including necessary form work complete all as specified and as directed. Note: Joints 12mm wide joints to full depth of PCC shall be provided at every 3 meters interval and at every change of direction and shall be filled with mixture of bitumen and sand in 1:3 by weight . Cost of joints shall be deemed to be included in quoted rate of this item complete all as specified and directed.

S&F in repair 0.56 mm thick plain aluminium sheeting bend to shape fixed with pins to door shutter to prevent water splashing,ridges, hips,valley gutters, drip and straight flashings over crumple joints complete all as specified and as directed.

M &L for water proofing treatment to sunken floor with the following course of treatment/ specification: (i) Cleaning top surface of floors /slabs and laying 50 mm thick (avg) PCC of grade M10 (Nominal mix) , mixed with WPC as per manufactrrer's instruction laid in slope 1:20 towards spouts including coveting corners (ii) 15 mm thick plastering in CM (1:4) on sides mixed with WPC as pe rmanufacturer's instruction. (iii) Applying 1st layer of slurry @ 0.488 kg / sqm mixed wth acrylic based polymer modified cementious compound @ 0.253 kg /sqm This layer shall be allowed to air cured for 4 hrs. (iv) applying 2nd layer of slurry @ 0.242 kg/sqm mixed with acrylic based polymer modified cementenous compound @ 0.126 kg/sqm.This layer shall be allowed to air cured for 4hrs followed with water curing for 48 hrs.(v) Applying a coat of industrial bitumen 85/25 penetration @ 1.50 kg/sqm on plastered and concrete surfaces (vi) Providing 150 micron thick polyutethene paint in two coats (each of 75 micron measured dry on dry surface over a coat of PU primer including preparation .

Contd item No 88.00 (Make of PU primer - Dek guard EP -302 of M/S Fosroc or equivalant approved brand.Make of PU paint - Dek guard PUor equivalant approved brand. (vii) 2 Nos 32mm bore GI medium grade 450mm long spout ,to be provided through external wall to drainout accumulated water.(vii) Sunken floor shall be tested for water tighness by filling water for 72 hrs before and after treatment work is carried out and ensure that no leakage /seepage exists (ix) Sunken portion shall be filled with lean concrete of grade M7.5 stone agreegate complete all as directed by Engr-in-Charge.

M&L for preparation of new orpreviously untreated steel and Iron surface of any description, not otherwise described over 10 cm width or girth and applying two coats of Synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L for cement concrete type C-2 1:3:6, 40mm graded aggregate as in surface channel complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick, for staircase steps (treads) in single piece (of length not more than 1200mm), laid over & including 15mm thick (average thickness) cement mortar (1:6) screed bed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) including provn of two Nos 3x3 mm grooves at tread of each step complete all as specified and as directed.

M&L for machine cut kota stone slab 15-20mm thick on vertical surfaces like riser of steps, skirting, in single piece (of length not more than 1200mm) over & including 15mm thick (average thickness) cement mortar (1:4) screed bed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and as directed.

S&F in repair MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

Removing & Hacking of existing concrete Carefully by low impact high frequency hammer OR by manual chipping without damaging the existing concrete or control sand blasting including cleaning the surfaces by air jet etc. complete.(Mode of measurement- per sqmt of breaking area of concrete )

Supply and applying a bond of Fosroc Nitobond SBR Latex, or Equivalent SBR Latex based bonding agent admix with cement as per manufacturer recommended ratio complete all as specified and directed.

Patch Repair Work by Polymer modified mortar : Repair of concrete surface with single component, fibre reinforced shrinkage compensated, polymer modified structural grade repair mortar like Fosroc Renderoc SP 40 or equivalent at a thickness of 25 mm. The repair mortar should have a compressive strength 45 N/mm²,flexture strength 7 N/mm² and tensile strength 2.5 N/mm² at 28 days.

M & L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed.

M & L 80 mm thick M-30 grade factory made vibratory compacted cement concrete rubber moulded, interlocking paver block any shape and size confiroming to IS 15658-2006 with grey cement and pigment as approved laid over and incl 50 mm thick consolidated sand cushion and joints filled with sand complete all as specified and directed.

M & L for PCC 1:2:4 type B-1 ,(using 20 mm graded stone aggregate) as. in coping /benching to sides of foot path fininished fair and even including necessary formwork etc complete all as specified and directed.

Demolition & breaking up drain pipes( salt glazed ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 150mm

Excavation in trenches n.exc 1.5 in deep and n.exc 1.5 m wide for foundation etc not exc 10 sqm on plan and getting out in soft / loose soil

Demolition of precast block masonary / Brick work or precast concrete article built in cement mortar

Demolition of reinforced cement concrete of any description and in any position such as precast manhole cover or cover slabs of septic tank etc (reinforcement cut as required to facilitate demolition)

Material and labour for precast reinforced cement concrete (nominal mix) Type A1 1:1.5:3 (20mm graded stone aggregate) as in manholes, well staining, well kerbs etc complete all as specified. Note: Reinforcement shall be measured and paid for separately.

Supply and fix PVC (SWR) pipes 160mm dia type 'A', single socketed, conforming to IS-13592:1992 in any length with rubber ring joints laid in trenches or in floors complete all as specified.

S&F for PVC (SWR) bends any radius fixed to PVC Pipes/Steel Gutters etc complete all as directed by Engr-in-Charge (Bore of bend 150mm)

M&L for mild steel TMT bars 6mm to 8mm dia cut to length , bent to shape required, including cranking , bending and binding with MS wire , not less than 0.9 mm dia or securing with clip.

M&L PCC 1:3:6 type C-2 (40mm graded aggregate) as in foundations, filling and mass concrete

M&L for 15 mm thick plastering in cement mortar 1:3 on fair faces of brick or concrete surface finished even & smooth without using extra cement

M&L for 20mm thick plastering in cement mortar 1:4 on other than fair faces of brick or concrete surface finished even and smooth with using extra cement

M&L PCC 1:3:6 type C-2 concrete bed to drain pipes including packing under & haunching against the sides of pipes after they are laid & tested dia of pipe 150mm

Returning ,filling in , including spreading , levelling , watering and well ramming in layer not exceeding 25 cm thick in soft/ loose soil complete all as specified.

Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L cutting into existing manhole for connecting new drains making good to pipe and rendering cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished & reforming benching as required dia of pipe 150mm

M&L for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

M&L for point wiring with 1.5 sqmm single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with multistranded copper conductor with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI Marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI Marked) with proper colour coding as earth continuity conductor connected to common earth dolly, modular sheet steel sunken terminal box of appropriate size suitable for modular switch/ fittings concealed in walls, with modular back plate, top cover fixed flush to wall for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles all as specified and as directed for the following :- (a) One light point controlled by one way switch 5/6 amps.

(b) As per Item No 118 above but for One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps.

(c) As per Item No 118 above but for One socket out let 5/6 amps point on the independent board

(d) As per Item No 118 above but for One socket out let 5/6 amps point on the same board

(e) As per Item No 118 above but for One bell point controlled by one way switch 5/6 amps.

(f) As per Item No 118 above but for One light point controlled by two way switch 5/6 amps.

All as per item No 118 above but for above but wiring with 2.5 sq mm single core multistranded copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and directed

S&F of Modular switch, single pole, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular switch, single pole, Two way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular switch, single pole, one way, 16 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 5 Pin, 6 Amp, 2 Module, 230 volts, ISI marked complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 6 Pin, 6/16 Amp, 2 Module, 230 volts, (ISI marked) complete all as specified and as directed.

S&F of Modular bell push, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of stepped type modular electronic fan regulator 120 watt 2 module suitable for 1200/1400 mm sweep energy saving fans,ISI marked complete all as specified and directed.

S & F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and directed.

S&F in ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed.

S&F IP 20, class I, LED light 1X18 W (or nearest next higher wattage) (4feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified and as directed.

S&F IP 20, Class I, LED Mirror light fitting 1 x 10 W, (or nearest next higher wattage) 5700 K, wall /Surface mounted with aluminium housing 2 feet long, integrated type, with high efficiency PMMA diffuser, integrated high efficiency electronic driver & surge suppressor of 2 KV or more, luminaire efficacy > 95 lumens/Watt, power factor >/ 0.90, operating range – 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/square blocks, screws etc complete including 01 No 10 W LED lamp with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size including necessary taking down the old unserviceable fitting complete all as specified and as directed.

S&F of Bulk head luminaire suitable for 10 Watt LED (or nearest next higher wattage) light IP66 grade, luminaire efficiency not less than 120 lumens/watts with and including 10 watt LED (or nearest next higher wattage) lamp and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor from ceiling rose to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified and as directed.

S&F of Decorative wall light fixture made up of polycarbonate suitable for 15 Watt LED retrofit of type B-22 base, IP66 grade, with and including 15 watt LED (or nearest next higher wattage) lamp and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified. Make - Havells , CAT No - LHFOECE1TZ1B014 or equivalent to Crompton/Surya/Philips.

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 35 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete incl removal of old unsv fitting complete all as specified and as dirceted.

Taking down carefully Ceiling fan from its original position and refixing / hanging after B/R plaster work complete all as specified and directed.

Material and labour for concealed sub-main wiring alongwith earth wire of size of 2 x 4.0 sq. mm + 1 x 4.0 sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits & making good to walls, floors etc complete, including taking down old unsv aluminium submain wiring complete all as specified and as directed. NOTE : Two runs of 4 sqmm conductor for main and one run of 4 sqmm conductor as earth wire with proper colour coding including one run run of PVC conduit shall be measured as one unit length. Connections of cables wit MCBs or bus bar shall be done through appropriate size brass/ copper thimbles

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, Triple pole & neutral with 200 amps rated bus bar, 415Volt IP-20 protection suitable for fixing MCB"S/lsolators with and including taking down old one complete all as specified and directed.

S&F MCB distribution boards (DBs) with sheet metal enclosure, double door, IP 43 protection, 240 Volts, 8 way, single pole and neutral, with 200 Amps rated copper bus bar (as per OEM), neutral link, ertth link earthing studs, suitable for fixing MCBs, without MCBs fixed flush to wall/other surface complete all as specified and as directed.

S&F MCB, Triple pole & neutral 63 amps, 240 volts, ‘C’ curve, 10KA complete with and including taking down old unsv one as complete all as specified and as directed.

S&F MCB, Single pole & neutral, 32 to 63 amps, 240 volts, ‘C’ curve, 10KA all complete with and including taking down old unsv one complete all as specified and as directed.

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete with and including taking down old unsv one complete all as specified and as directed.

M & L for sheet metal enclosure fabricated out of 2.0 mm thick CRCA sheet, totally enclosed type, dust & vermin proof, with suitable sized supporting MS angles & suitable openings at top & bottom for entry of outgoing / incomming cables, fixed with nuts & bolts & front side openable with hinged shutter with suitable locking arrangement duly painted with 2 coats of powder coated paint over a coat of red oxide primer (spray paint) with minimum dimensions (90 x 75 x 20 cm ) flush to wall for incorporating 01 No TPN DB, 04 Nos electronic meters etc complete all as specified and as directed.

Material and labour for earthing complete with galvanized steel plate electrodes of size600x600x6mm thick burried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised wire 4.00 mm earth lead by means of nuts, bolts, checknuts and washers including 15 mm bore galvanized iron pipe, medium grade for protection of earth lead upto the length of 7.5 meter towards test terminal and 20 mm bore galvanized iron pipe, medium grade for watering, and providing of charcoal and common salt in alternate layers, includig necessary earth work in any type of soil and including PCC pit in PCC 1:2:4 with provision of wire mesh and funnel, complete all as shown in electrical plate No 5 of SSR Part- I including testing on completion all as directed and as specified.

M/S East India Traders

SS SHARMA

R K AGARWAL

SHRI R S YADAV

Shri Amarnath Sah

M/S MOHAN KUMAR BANSAL

SINGH & CO

M/s. RAMPHAL GARG