SPECIAL REPAIR OF BLDG NO T-11 AND T-04 AT RAJOURI UNDER GE 862 EWS

Amount

B&R PORTION:- Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, all as specified.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

Rolled mild steel Joist,channel angle or tee sections fixed independently without connecting plates etc (cut to ordinary lengths i.e with in 20mm of the length indicated) confirming FE 410 W Gde E 250 quality complete all as specified.

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, valley gutter, ridge & similar works fixed with self tapping screws complete all as specified.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

Walling of random rubble stone masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

Description all as per item No.07 above, but except stone complete all as specified and directed

Extra over stone walling of random rubble walling, uncoursed or brought for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified.

Raised pointing in cement mortar 1:4 to random or polygonal rubble, uncoursed or brought upto courses, complete all as specified.

Taking down cement plaster of any description on stone or brick walls etc. including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

20mm thick rendering in CM 1:4 on other than fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each, complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5Sqm each, complete all as specified.

Factory made Pressed steel frames of size 125x60mm made out of PBI sheet 1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinge,lock strike plate etc.complete including bottom of each chowkat to be welded with 02 Nos 25x25x3mm thick angle iron projecting 10cm on either side & PCC 1:3:6 type C-0 in back filling of chowkats & tarring back of chowkats and holdfasts complete all as specified & directed.

35mm thick 2nd class hard wood plain, framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of 12mm thick veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed.

35mm thick 2nd class hardwood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete, all as specified.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

Factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, hold fast etc., complete with glazing bars, dovetailed or welded, complete all as specified.

Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, hold fast etc., complete without glazing bars, dovetailed or welded, complete all as specified.

Mild steel work conforming to Fe-290 (Gde E-165) as in grills, gratings etc. with ends of bars shouldered and/ or rivetted or forged into spikes; framed guard bars, and similar works, complete all as specfied.

Galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified.

Sheet glass ordinary quality, 4mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified.

PCC 1:2:4, type, B-1 (using 20mm graded crushed stone aggregate), as in coping, benching, plinth band, bed block, PCC blocks for hold fast including rounded or chamfered angle as directed including necessary form work etc., complete all as specified and directed.

Mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified.

Aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

Extruded aluminium alloy handles, fabricated type, anodised of size 125mm and fixed, complete all as specified and directed.

300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section of cast aluminium alloy and fixed, all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets all as specified & directed.

4mm thick fibre cement E-board designer pattern (classic) ISI Marked IS-14862-2000 of size 600x600mm as in false ceiling fixed with screws as per manufacturers instructions (Make : everest or equivalent as approved by GE) all sections shall be coated white. The frame shall comprise of GI frame work grid of size as GI Tee of size 38x24x4mm as main runner, 28x24x3mm thick GI Tee as cross runner and GI angle of size 24x24x4mm as the wall perimeter including GI adjustable suspender 4mm wire of required length hange with ceiling with accessories spread at 1200mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4mm dia to be fixed with approved rawl plugs, level adjusters and screws etc. The last hanger at the each end of main runner shall not be greater than 450mm from adjuscent wall, flush fitting of 1200mm long cross tee with double stitching to be interlocked between main runners, complete as specified and as directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11Sqm but n exc. 0.18Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:4), complete all as specified and directed.

Glazed ceramic coloured tiles (450x350mm) / (450x300mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

Vitrified ceramic tiles 10 mm thick (square/rectangular) area of each tile exceeding 0.36sqm but not exceeding 0.42sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:4), complete all as specified and directed.

Plain cement concrete 1:3:6 type C-1(using 20mm graded crushed stone aggregate) as in surface channels and drains including necessary form work, complete all as specified.

Hard core of broken stone/boulders of gauge n exc 63mm deposited spreed and leveled in layers n exc 15cm thick watered and rammed to a true surface, complete all as specified.

75mm thick PCC 1:3:6 Type C-2 (using 40mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection laid in slope 1:12, finished the surfaces even & fair, including filled the joints with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight to through out joints of 6mm thicks, complete all as specified.

Dismantling PVC water tanks and removing to storing of capacity exc 250 ltr but not exceeding 500 ltr complete all as specified.

Rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 500 Ltrs incl with 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and as directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, Complete all as specified and directed.

Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified.

Steel water tubing 20mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceiling or laid in floors, complete all as specified.

Bib tap 15 mm bore with flange, Brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repairs, complete all as specified. Make:- Jaquar cat part No CON-047KN or equivalent cat part of make as specified in P.S..

15mm bore Stop valve cast copper alloy chromium plated fancy type with long shank and cup (concealed type) screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union, fixed in repairs, complete all as specified. Make:- Jaquar cat part No CON-069KN or equivalent cat part of make as specified in P.S.

20mm bore Gun metal, globe or gate valves (ISI Marked), with iron wheel head, screwed both ends for iron pipe. Fixed in repairs, complete all as specified.

32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed in repairs, complete all as specified.

PVC flexible waste pipe, 80cm long including coupling suitable for 32mm dia coupling for WHB/Sink, fixed in repairs complete all as specified.

Tubular towel rail 60mm long 20mm dia D type aluminium anodised incl necessary brackets, fixed in repairs, complete all as specified and directed.

Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), suitable for floor taps fixed in repairs, all as specified and directed.

PVC connection 15mm size with PTMT nuts on both ends of length 450mm fixed in repair, complete all as specified.

PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in trenches/floors as soil pipe, fixed in repair, complete all as specified and directed.

PVC (SWR) bends any radius 110mm bore fixed, complete all as specified.

Vitreous china squatting pan (Orissa pattern) size 680 x 470 mm, snow white, with 'P' or 's' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. fixed in repairs including lime concrete bedding, complete, all as specified.

Vitreous china wash hand basin, white, flat back, size 550x400 mm excluding taps, waste, chain & plug and porcelain stopper but including brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc fixed in repairs, complete all as specified.

Preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of Ist quality over a coat of pink primer,complete, all as specified.

Preparation of old painted wooden or wood based surfaces of any description not otherwise described, over 10cm width or girth including knotting and stopping as required and applying one coat of synthetic enamel paint, complete all as specified.

Preparation of new or previously untreated steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer, complete all as specified and as directed.

Preparation of old painted steel surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint in camouflage pattern/single shade, complete all as specified.

Preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of distemper oil emulsion over and including chalk whiting primer, complete as specified and directed.

Complete removal of existing treatement from wall plaster including cornices pilaster etc and applying two coats of distemper oil emulsion over and including chalk whiting primer, complete as specified and directed.

Complete removal of existing treatement from wall plaster including cornices pilaster etc and applying two coats of cement base paint over and including chalk whiting primer, complete as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified.

75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring/path etc, complete all as specified and directed.

Chequered cement concrete tiles 300x300x 25mm thick of any colour as approved by GE, set & jointed in neat cement slurry in floors and pointed with grey cement mixed with pigments, laid over and including 20mm thick screed bed in CM 1:6 including dismantling old unsv tiles with cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed, complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopper ends etc complete all as specified.

E&M PORTION:- Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

Point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with sunken galvanised pressed steel box of thickness not less than 1.12mm of appropriate sizes copvered with 3mm thick phenolic laminated white sheet cover with all requisite accessories such as PVC elbow, Tee, collars, bends etc. for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light / fan point controlled by one way switch 6 Amp complete all as specified.

One 3 pin socket outlet 6 amp on same board complete all as specified.

One 3 pin socket outlet 6 amp independent board complete all as specified.

One bell point controlled by one way switch 6 Amp complete all as specified.

Description all as per srl item No 69 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 1.5 Sqmm as in continuous earth wire.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified.

Switch piano flush type 16 Amp single pole one way, (ISI marked), complete all as speciied.

Socket outlet multipurpose combination 2 in 1, 5 pin, 6 Amp flush type universal,complete all as specifed.

Socket outlet multipurpose combination 2 in 1, 3 pin, 6 and 16 Amp flush type universal,complete all as specifed.

Switch bell push flush type 5 Amp single pole one way (ISI marked) complete all as specified.

Electric bell ding dong type 230 volts AC supply 50 Hz complete all as specified and directed by Engineer-in-Charge.

Ceiling rose, 3 phase PVC/poly carbonate, insulated body, compete all as specified.

Taking down ceiling fans of any type and size after disconnecting from existing ceiling rose to connector and clamp hooks during re-wiring / any repair work and refixing the same in position after repair work and re-connecting with trhee core cable of required size, complete all as specified

Ceiling fans of 12mm sweep AC single phase 230/240 volts 5 star rating with all accessories & fixing arrangement, complete all as specified.

Stepped type electronic fan regulator flush type fixed on the existing phenolic laminated sheet etc. for 1200 / 1400mm sweep, complete all as specified.

Heavy duty exhaust Fan 300mm sweep 1400 RPM, single phase 240 Volts AV 50Hz including all connecting accessories, complate all as specified and directed.

Tube light fitting with LED 1 x 18W tube Rod with end cap complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting fixed, complete all as specified and directed. Make:-Havells Cat Part No:- LUMILINEBS18WLED865SPCWH or Equivalent cat part of make as specified in Appx 'A' here in after.

Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 8 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning fixed in repairs, complete all as specified. Make:- Havells cat part No-DHDPSHODPW08 or Equivalent cat part of make of Legrand / Indoasian / L&T

MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series fixed in repair, complete all as specified. Make:-Havells cat part No-DHMGCSPF006-032 or equivalent cat part of make-Legran / INDOASIAN / L&T

MCB double pole 6 to 32 amps 240 volts 10 KA 'C' series fixed, complete all as specified. Make:-Havells cat part No-DHMGCDPF006-032 or equivalent cat part of make-Legran / INDOASIAN / L&T

Sub main wiring with single core cable 2 x 4 sq mm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 2.5 Sq mm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-2 wire of 4sqmm, 1 wire of 2.5 sqmm and one run of pvc casing caping shall be measured as one unit.

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 8mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing, complete all as specified and directed.

1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, two single core cable flat or circular of size 6Sqmm, complete all as specified and directed.

LED street light fittings 25 Watt made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening seperate driver compartment complete with hosing with all accessories pre wired with and including 32mm dia GI pipe bracket of 1.2 mtr made to shape as required fixed on wall or pole with FI clamp of required shap & 40x6mm siize, nut, bolts, washers and making connection with copper flexible cable of suitable size to light fitting fixed, complete all as specified and directed. Make:-Havells Cat Part No:-ENDURAPEARLSL25WLED757SASYTOPCMP or Equivalent cat part of make as specified in Appx 'F' here in after.

Supply laying in replacement and testing XLPE, insulated screened, PVC bedded galvanized steel strip or wire armoured, electric power cables, heavy duty, with aluminium conductor, 1100 volts grade, 2 core, cross sectional area 10 Sqmm, all as specified and directed.

GI pipe light grade 40 mm bore for cable protection fixed on poles or laid in trenches, under floor, ducts etc with fixing clamps of required size, nuts, bolts, washers etc. fixed, complete all as specified.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation etc for shafts, wells,cesspits, man holes, pier holes etc not exceeding 10 sqm on plan and not exceeding 1.5m depth and getting out in any type of soil, complete all as specified.

Returning, filling, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in any soft distintegrated soil, complete all as specified and directed.

Removal of excavated material to a distance not exc 50m and depositing where directed at a level not exceeding 1.5mtr above starting point complete all as specified and directed

Dry sand cushioning to UG cable 8 cm thick before laying and 15cm thick after laying complete all as specified and directed. Note:- 1.Dry fine sand of best available quality shall be used. 2.Punned thickness shall be made and paid.

Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

SATVIR GUPTA ENGINEER and CONTRACTOR

M/S RAHUL GUPTA

M/S Ashok Kumar Gupta