Construction of Additional Accommodation at Govt. Sr. Sec. School Mundhi in Distt. Kangra

Amount

Excavation in foundation, trenches etcetera in earth work involving all classification of soil such as pick work, pick jumper work, blasting work, soft or hard rocks including chiseling/wedging out of rocks where blasting work is prohibited or any other mixed variety of intermediate soil, dewatering and removal of slush if arrisen during course of construction and lifts upto all heights including stacking the excavated soil not more than three meters clear from the edge of the excavation and then returning the stacked soil in 15 cm (fifteen centimeter) thick layers when required into plinths, sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus excavation earth within all leads,lifts by any mode of transportation and other incidental, as per the direction and entire satisfaction of Engineer-in-Charge. Any loss to the private and public property during course of construction shall be absolute responsibility of the contractor. Rate inclusive royalty, malkana, toll tax, GST and other taxes imposed by the government.

Excavation in drains and channels etcetra in earth work in all classification of soil, such as pick work, jumper work, pick jumper work, blasting work, hard and soft blasting, saturated soil including chiseling or any other mixed variety of soil, lift upto any heights, stacking the excavated soil for all heights from the edge of excavation and then returning the stacked soil in 15cm (Fifteen centimeter) layer when required into plinths sides of foundations etcetra Consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as directed by the Engineer- Incharge, within all leads, lifts of material and other incidentals. Rate is inclusive of royalty, malkana, toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etcetra, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation, Footings, bases of columns and mass concrete. The rate is inclusive of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etcetra, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etcetra including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams, cantilevers, girders, lintels, sides, and soffits of beams haunchings, cantilevers bressumers and lintels upto all depths in all floor including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etcetra, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillars , posts and struts, square, rectangular, polygonal in plain in all floor level including of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing in all floor including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimetre) so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surface such as walls up to any thickness / any height including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls up to any width including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:4:8 (One cement isto four sand isto eight aggregate) graded crushed stone aggregate 40mm (forty millimeter) nominal size mechanically mixed and curing complete, excluding cost of form work in foundation and plinth as per approved specification, drawing including entire carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:3:6 ( one cement isto three sand isto six graded, crushed stone aggregate 40mm (forty millimetre) nominal size) mechanically mixed and curing complete excluding cost of form work in foundation and plinth including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete as per PWD specification. The rate is inclusive of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of royalty, malkana, toll tax, GST and any other taxes imposed by the government.

Stone filling tightly dry hand packed under flooring including ramming and consolidation complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidental . The rate is including of octroi, royality, Malkana, toll tax , sales tax or other taxes imposed by the government.

Supplying and filling broken/ crushed stone/ brick bats of hard stone of 40 mm (Forty millimetre) size complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidental . The rate is including of octroi, royality, Malkana, toll tax , sales tax or other taxes imposed by the government.

Providing and laying cement concrete work of grade M20 mix design to obtain the minimum compressive strength 20N/mm2 ( twenty newton per square millileter) with cement contents not less than 330 kg/ cum (Three hundred thirty Kilogram per cubic metre) with mechanically mixed and vibrated curing complete excluding cost of form work and reinforcement for reinforced concrete work in foundation and plinth as per approved specification, drawing and design including entire carriage of material with in all leads, lifts and other incidentals and further as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of octroi, Royality, Malkana, sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work of grade M20 mix design to obtain the minimum compressive strength 20N/mm2 ( twenty newton per square millileter) with cement contents not less than 330 kg/ cum (Three hundred thirty Kilogram per cubic metre) with mechanically mixed and vibrated curing complete excluding cost of form work and reinforcement for reinforced concrete work in foundation footing, base of colums, and the like mass concrete as per approved specification, drawing and design including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work of grade M-20 (M-twenty) design mix to obtain the minimum compresive strength 20N/mm2 (Twenty newton per square millimeter) with cement content not less than 320 kg/cum (Three hundred twenty Kilogram per cubic metre) and curing complete and mechanically mixed and vibrated as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in suspended floor roofs, landing and shelves and their supports balconies, beams, girder, bressumers and cantiliver upto any floor level including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work of grade M-20 (M-twenty) design mix to obtain the minimum compresive strength of 20N/mm2( twenty newton per square millimetre) with cement content not less than 320 kg/cum (Three hundred twenty Kilogram per cubic metre) mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design excluding cost of form work and reinforcement for reinforced concrete work in coulmn, pillars posts and struts upto any floor level including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work of grade M-20 (M-twenty) design mix to obtain the minimum compresive strength of 20N/mm2( twenty newton per square millimetre) with cement content not less than 320 kg/cum (Three hundred twenty Kilogram per cubic metre) mechanically mixed and vibrated including curing complete as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in stair cases (except spiral stair cases) excluding landings, but including preparing of top surfaces and finishing of nosing upto all floor levels including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work of grade M-20 (M- Twenty) design mix to obtain the minimum compressive strength of 20N/mm with cement contents not less than 320 kg/ cum (Three hundred twenty kilogram) per cubic metre, mechanically mixed and vibrated including curing complete in reinforced concrete Chhajjas for all thickness up to floor two levels up to all heights including finishing the exposed surface with cement mortar 1:3 (One cement isto Three sand) to give a smooth and even surface including centering/ form work and curing complete but excluding the cost of reinforcement for reinforced concrete work . including of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work of grade M-20 (M-twenty) design mix to obtain the minimum compresive strength 20N/mm2 (twenty newton per square millimetre) with cement content not less than 320 kg/cum (Three hundred twenty kilogram) per cubic metre, mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design including cost of form work but excluding cost of reinforcement for reinforced concrete work in moulding as in cornies, window sills etcetra not exceeding 15cm in girth upto all floor levels including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work of grade M-20 (M-twenty) design mix to obtain the minimum compresive strength of 20N/mm2 (twenty newton per square millimetre) with cement content not less than 320 kg per cubic meter mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in wall any thickness but not less than 0.10 M( Zero point ten)meter including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete grade M-25 (M-Twenty five) design mix with minimum compressive strength 25N/mm2 with cement contents not less than 360 Kg (Three hundred sixty kilogram per Cubicmetre) mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design excluding the cost of form work and reinforcement for cement concrete work in suspended floor roofs, landing and shelves and their supports balconies, beams, girder, bressumers and cantiliver upto any floor level including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in cement mortar 1:6 (one cement isto six sand) including curing complete as per approved specification, drawing, design and curing complete including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Random rubble masonry with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement isto six sand isto Twelve graded stone aggregate) 20 mm (Twenty millimetre nominal size) at plinth level in cement mortar 1:6 (one cement isto six sand ) including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Applying cement slurry on Reinforcement Cement concrete slab or cement concrete work using 2.75 kgs (Two point seventy five Kilogram) of cement per square meter of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete as per HP. PWD specifications excluding cost of centring and shuttering including carriage in all leads,lifts and as per the direction of Engineer in charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying tor steel of TataTISCO, SAIL reinforcement for reinforced cement concrete work including bending, binding and placing in position complete in all respects as per approved drawing, design, and specification in all floor levels including the cost of binding wire and dewatering if arrisen during placement of reinforcement as per PWD specification and approved, drawing design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying Damp Proof Course 100mm (One Hundred millimetre) thick with cement concrete 1:2:4 (one cement isto two sand isto four graded crushed stone aggregate 12.5mm (Twelve decimal five millimetre nominal size) mechanically mixed including cost of form work and curing complete, as required at site as per H.P.P.W.D. specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rate is including octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government.

Applying a coat of hot bitumen (mexphalt) 80/100 (Eighty by hundred) or VG-10 using 1.70 kg (one decimal seven) kilogram per square meter on damp proof course after cleaning the surface with a piece of cloth lightly socked with kerosene as per PWD specification including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.

Second class brick work using common burnt clay building bricks in cement mortar 1:6 (one cement isto six sand) in super structure upto all floor levels as per PWD specification, drawing and design and curing complete including scaffolding and cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Second class brick work using common burnt clay building bricks in cement mortar 1:4 (one cement isto four sand) in super structure upto all floor levels as per PWD specification, drawing and design and curing complete including scaffolding and cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Second class half brick work using common burnt clay building bricks with hoop iron in cement mortar 1:4 (one cement isto four sand) in super structure as per PWD specification, drawing and design and curing complete including scaffolding and cost, carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S. channels in doors, windows clerestory windows frames manufactured from M.S. channel section 75x40x4mm (Seventy five into Forty into four millimetre) with M.S. flat 75x4mm (Seventy Five into Four millimetre) combination as per specifications design, drawing including hinges, jambs, beeds if required thrashold of M.S. angles 50x25mm (Fifty into Twenty five millimetre) welded or rigidly fixed by mechanical means lugs, with split ends tails to each jambs including steel butts hinges 2.5mm (Two decimal five millimetre) thick with a provision of locking arrangements, shock observers as specified and applying a coat of approved steel primer after pretreatment of the surfaces as directed by the Engineer-in-Charge. The rate is inclusive for carriage of material with in all leads, lifts and other incidentals including sale tax, toll tax, GST or all type of other taxes imposed by the Government.

Providing and fixing factory made double shutter for steel windows side hung (one glazed and other wire gauged) of standard rolled steel section jointing mitred and welded with manufactured to relevant ISI standard specification with 16x3.15mm (Sixteen into three decimal fifteen millimetre) lugs10cm (Ten centimetre) long with steel plugs and screws or rawl plugs screws or with fixing clips or with bolts and nuts as required and iron fitting, including providing and fixing of glass pans with special putty of glazed side of shutter and wire gauge of IS designation 85G with metal beading on other side complete including priming coat of red lead paint as directed by the Engineer-in-Charge. The rate is inclusive for carriage of material with in all leads, lifts and other incidentals including sale tax, toll tax, GST or all type of other taxes imposed by the Government.

Providing and fixing angle iron door frames (single rebate) manufactured with frame for steel section of 35x35x4mm (Thirty five into thirty five into four milimetre) and M.S. flat 50x5 mm (Fifty into five milimetre) in combination as per Drawing and design including hinges jambs, locks, mild steel M.S. angle 50x25mm (Fifty into twenty five millimetre) welded or rigidly fixed by mechanical means lugs with split and tails to each jamb including steel butt hinges 2.5mm (Two point five millimetre) thick with provision of locking arrangement and shock observers as specified and applying a coat of special steel primer as directed by the Engineer-in-Charge. The rate is inclusive for carriage of material with in all leads, lifts and other incidentals including sale tax, toll tax, GST or all type of other taxes imposed by the Government.

Providing and fixing Factory made PVC door frame of size 50x47mm (Fifty into forty seven millimetre) wall thickness of 5mm, made out of extruded 5mm (Five millimetre) rigid PVC fram sheet mitred at comer jointed with 2 Nos. (Two numbers) of 150mm (One hundred fifty millimetre) long brackets of 15x15mm (Fifteen into fifteen millimetre) M.S. squares tobe the vertical door with profiles to be reinforced with 19x19mm (Nineteen into ninetenn) M.S. Square metre to be of 19 (nineteen) gauge E.P.D.M rubber gasket weather seal to be provide through out the fram the door to be fixed to the wall using M.S. screws of 100mm size complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing to existing door frames, 30mm thick factory made PVC panelled door shutter consisting of frame made out of M.S. tubes of 19 gauge( Ninteen gauge) thickness and size of 19mm x19mm ( Ninteen into ninteen millimeters) for styles and 15mmx15mm ( fifteen into fifteen millimeters)for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm( five millimeters) thick heat moulded PVC "C" channel of size 30mm( thirty millimeters)thickness, 70mm( Seventy millimeters) width cut of which 50mm ( fifty millimeters)shall be flat and 20mm ( twenty millimeters) shall be tappred in 45 ( forty five)degree angle on either side forming style and 5 mm( five millimeters) thick, 95mm ( ninety five millimeters) wide, PVC sheet out of which 75mm shall be flat and 20mm( twenty millimeters) shall be tapered in 45 ( forty five)degree on the inner side to form top and bottom rail and 115mm( one hundered fifteen millimeters) wide PVC sheet out of which 75mm (seventy five millimeters) shall be flat and 20mm ( twenty millimeters) shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm( ten millimeters) thick, 20mm( twenty millimeters) wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails jointed mitred and jointed with solvant cement adhesive including fixing of PVC shutter with existing frame with MS butt hinges/riveted with necessary screws of code No. 9.120 of Rajshri including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S. plain grills 10x10mm (Ten into ten millimetre) square bar in combination of 20x4mm (Twenty into four millimetre) M.S. flat as per design required pattern in wooden frames of windows etc. with M.S. round headed bolts and nuts or by screws including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing Factory made Century/ Alpro/ Duro Ply/ Green Ply No. IS-2202 or equivalent 35mm (Thirty five millimetre) thick flush door shutters both side commercial including non decorative phenol bonded termite resistant and bailing water proof core of block board constructed with Ist class frame of hard wood and well matched commercial 3 (Three) ply veneer with vertical grains of cross bands and both faces of flush door EPDM gasket. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 5mm (Five millimetre) thick glazing in aluminium for windows, ventilators with glass pan of Modiguard / Saint Gobain Dormer shutters with PVC / neoprens gaskets complete weight not less than 12.50 kg/ m2 (Twelve decimal five zero kilogram per square metre) as per the approved Drawings, design and specification and the direction of the Engineer -in Charge, (Cost of aluminium snap beeding shall be paid in basic item) including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 5mm (five millimetre) thick Frosted Glass panes of Modiguard/ Saint Gobain in aluminium for toilet window and ventilator with PVC / neoprens gaskets complete weight not less than 12.50 kg/ m2 (Twelve decimal five zero kilogram per square metre) as per the Architectural Drawings approved specification and design and the direction of the Engineer-in Charge, (Cost of aluminium snap beeding shall be paid in basic item) including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm (Twenty into ten into two millimetre) and braced with flat iron diagonals 20x5mm (Twenty into five millimetre) size with top and bottom rails of T.iron 40x40x6mm (Forty into forty into six miilimetre) with 38mm (Thirty eight millimetre) dia steel pulley complete wityh bolts and nuts locking arrangements stoppers, handles, including applying a priming coat of red lead paint including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 40x3mm (Forty into three millimetre) flat iron hold fast 40cm (Forty centimetre) long including fixing to frame with 10mm (Ten millimetre) diametre bolts, nuts and wooden plugs and embeding in cement concrete block 30x10x15cm (Thirty into ten into fifteen centimetre) 1:3:6 (One Cement isto Three Sand isto Six graded stone aggregate 20mm (Twenty millimetre)) including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing the complete box of cup board shall be made of 19mm (Nineteen millimetre) thick water proof termite resistant commercial board of Uniply / Green ply/ IS marked including shelves.Back side of board shall have 6 to 8 mm (Six to eight millimetre) thick water proof ply all the cut portion of board shall have 6 mm (Six millimetre) thick hard wood edging. The shutter from all side shall be finished with 1mm thick lamination ISI Marked of approved shade of Century / Greenlam /Action Tesa and 19 mm (Nineteen millimetre) thick water proof comercial board of uniply / Greenply for shelves including hinges and handle complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government. (The area of cup board shutter shall be measured saperately).

Providing and fixing Megnetic Catcher for cup boards shutter with necessary screws complete including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 65x35mm (Sixty five into thirty five millimetre) special quality bright finished brass cup board lock with six leavers including necessary screws etc complete (Indian make) including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 25mm (Twenty five millimetre) diametre stainless steel curtain road brackets, plugs etcetra complete including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 300x16mm (Three hundred into sixteen millimeter) size coloured / anodized aluminum sliding door bolt, anodized transparent or dyed to required colour and shade with bolts and nuts, screws etcetra complete. The rate is inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 250x10mm (Two hundred fifty into ten millimetre) size coloured anodized aluminum tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetra complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 100x10mm (One hundred into ten millimetre) size M.S. tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetra complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 125mm (one hundred twenty five millimetre) size coloured / anodized aluminum handle anodized transparent or dyed to required shade or colour with necessary screws etcetra complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 100mm (One hundred millimetre) size M.S. handle anodized transparent or dyed to required shade or colour with necessary screws etcetra complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 250 mm (Two hundred fifty millimetre) oxidised M.S. hooks and eyes complete including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax toll tax, GST and any other taxes imposed by the government.

Providing and fixing Aluminium oxidized hydraulic door closer ISI Marked with necessary screws complete including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 100mm (One hundred millimetre) bright finished brass floor door stopper with rubber cushion screws etcetra to suit shutter thickness complete including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying 600x600 mm (Six hundred into six hundred millimetre) double charge / Ultra Charge vetrified tiles of Resitile/ Nitco/ Kajaria/Rak/Johnson/Bell water proof stain and impact resistent heavy duty vitrified tiles of approved shade and colour in flooring laid over 12mm (Twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as per required complete as per specifications, approved drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying 600x600 mm ( six hundred intosix hundred millimeters) full body matt finish vetrified tiles of restile/ Nitco/ Rak/ Simpolo/ Kajaria/ Johnson as per approved shade in flooring and laid over 12 mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as per approved specification, drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying Precast terrazzo tiles 300x300x25mm (Three hundred into three hundred into twenty five millimetre) thick automatic Hydraulic compressed and polished Terrazzo tiles of NTC in flooring and skirting ISI marked No IS: 1237 top layer in (50%) (Fifty Percent) white and 50% (Fifty percent) in white yellow dark green and maroon chips of size 0,B and 2B size with marble chips of specified sizes laid in floors, treads of steps and landings laid on a bed of 25mm (Twenty five millimetre) average thickness of cement mortar 1:6 (one cement isto six sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (where ever required) including rubbing and polishing complete as per specifications, approved drawing and design including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying Precast terrazzo tiles 300x300x25mm (Three hundred into three hundred into twenty five millimetre) thick automatic Hydraulic compressed and polished Terrazzo tiles of NTC in flooring and skirting ISI marked No IS: 1237 top layer in (50%) (Fifty Percent) white and 50% (Fifty percent) in white yellow dark green and maroon chips of size 0,B and 2B size with marble chips of specified sizes laid in floors, treads of steps and landings laid on a bed of 25mm (Twenty five millimetre) average thickness of cement mortar 1:6 (one cement isto six sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (where ever required) including rubbing and polishing complete as per specifications, approved drawing and design including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying 300x300 mm (three hundred into three hundred millimetre) Antiskid Cermic Tiles of Premimum quality of Nitco/ Kajaria/ Johnson / Orient Bell in flooring & skirting laid over 12mm (Twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete upto all floor level in all heights as per approved specifications, drawing and design and entire carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in- Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying 300x300 mm (three hundred into three hundred millimetre) where as required Cremic Glazed tile of Kajaria/ Nitco/ Simpolo/ Somany/ Jonson/ Orient Bell in skirting, riser of steps and dado laid over 12mm (Twelve millimetre) thick cement mortar 1:3 ( one cement isto three sand) and jointed with white cement slurry mixed with pigment to match the shade of tiles as required complete upto all floor level in all heights as per approved specification, drawing and design and entire carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in- Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying 300x450 mm (three hundred into four hundred fifty millimetre) where as required Cremic Glazed tile of Kajaria/ Nitco/ Simpolo/ Somany/ Jonson/ Orient Bell with one border matching contrast at top laid over 12mm (Twelve millimetre) thick cement mortar 1:3 ( one cement isto three sand) and jointed with white cement slurry mixed with pigment to match the shade of tiles as required complete upto all floor level in all heights as per approved specification, drawing and design and entire carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in- Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying 19 mm (Nineteen millimetre) thick polished Grey/black granite stone in work counter / top heaving semiround noising, moulding and laid over 20 mm ( twenty millimetre) thick base of cement mortor 1:3 (one cement isto three sand) and jointed with cement slury mix pigment to match the shade of granite stone including rubbing polishing, moulding and nousing complete as per approved specification, drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Kota stone slab 25 mm (Twenty five millimetre) thick in Single slab with round noising for treads and riser of stairs approved shade 20mm (Twenty millimetre) average thick base of cement mortar 1:3 (One cement isto three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing as per approved specification, drawing and design and entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying 300x300x25mm (Three hundred into three hundred into twenty five millimetre) labrador design(Rainbow series of NTC/ Atlantic slab flooring 40mm (forty millimetre) average thick on 20mm (twenty millimetre) average thick fixed on floor, Ramp cement Mortar 1:3 (One cement isto three sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rbbing and polishing, cutting and moulding complete including carriage of materials within all leads, lifts and other incidentals. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 50 mm ( fifty millimetre) dia hollow stainless steel hand rail pipe hand rail slip resistance with rounded ends at two level at 75 cm and 90 cm ( Seventy five centimetre and ninety centimeter) high and extended 30 cm ( thirty centimeter) beyond top and botton of ramp as per detail and 25 mm ( twenty five millimetre) dia SST bullasters welded to 50 mm ( fifty millimetre) dia SST pipe embended in cement concrete @ 600 mm (six hundred millimetre) center to center as per detail drawing, design and specification including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax toll tax, GST and any other taxes imposed by the government.

Providing and Fixing 50mm (Fifty millimetre) diametre hollow stainless steel knock down railing of kich AISI 316 of fixed over 35mm (Thirty five millimetre) diametre S.S flat baluster in combination with 15x20mm diametre baluster (Design code DT-53-2 - 163 ) placed at 1200mm (Twelve hundred millimetre) daimetre centre to centre along with 3 (Three) Numbers @ 16mm (Sixteen millimetre) mid rail connected at the side of baluster with fixture. The baluster would be fixed on to floor with casted base plate of minimum 6mm (Six millimetre) thickness. Base plate shall be concealed with suitable S.S 316 grade cover cap. Railing height to be taken 85 cm (Eighty five centimetre) from floor level complete in all as per specifications, approved drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing pre-painted steel sheet ridge or hips of TATA Durashine/ Sail 60cm (sixty centimetre) over all with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheets with top coat of regulat modified polyster organic coating of 20 (twenty) microns over 5 (Five) microns primer coating + back coating of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetre) dia prepainted bitumen washers complete in all respect as per approved specifications, drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing pre-painted sheet valleys 90cm (Ninety centimetre) over all with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet of TATA Durashine/ Sail in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (Five) microns coating + back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with J or L hooks, bolts and nuts 6mm (Six millimetre) dia with prepainted limpet and bitumen washers complete in all respect as per specifications approved drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 0.60mm (sixty millimetre) thick prepainted steel sheet (IS marked Z-120) of TATA Durashine/ sail over steel trussed in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating of back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (six millimetre) diametres with prepainted limpet, rubber washers complete with all accessories as required as per specification, drawing and design including carriage of materials with in all leads, lifts and other incidentals as per the direction and entire satisfaction of Engineer-in-charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 30cm (Thirty centimetre) wide 25cm (Twenty five centimetre) deep plain G.I. sheet gutter of 0.60mm (zero decimal six zero millimetre) thick sheet fixed with bolts, nuts and washers etcetra having dome shape gratting including making necessary connections with rain water pipe complete including cost and carriage of material with in all leads, lifts and other incidentals as per specifications, approved drawing and design, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S. B.P. sheet 2 mm (two millimetre) thick of TATA/SAIL for eaves board/Facia/Soffit/Ceiling including cutting, fixing and jointing with gas/electric welding with steel roof member and applying a coat of red lead primer complete as per PWD specification, approved drawing and design (frame work is to be measured and paid for separately) including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing water proof treatment in depressed slab shall be done with fixit pidilite proof coating shall be done in two coats apply first coat of Dr. fixit fast flex to clean the saturated surface maintaining coverage of 6.70 Square feet ( six point seven zero square feet)( 0.60 Sqm) ( Zero point sixty suqare metre) per kilogram to achive 1 mm ( one millimetre) thickness. The coating shall also be extended upto 300 mm (thirty hundred millimetre) vertically. The second coat shall be applied in opposite direction after 4 to 6 hours of application of Ist coat then sprinkle sand on top surface of applied Dr. fixit fast flax white steel tacky over the second coat then apply cement mortor 1:4( one cement : four sand) admixure with 200 ml (two hundred milliletre) of pidi proof LW @ 200 ml/50Kg towards drain pipe, while the second coat Dr. Fixit still tacky as per specifications, and approved drawing and design.The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing flushing 38cm (Thirty eight centimetre) overall with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet of Tata/sail with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetre) dia meter & prepainted G.I. limpet & bitumen washers complete including of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 110 mm (One hundred ten millimetre) diametre high pressure P.V.C spigot and socket soil, waste and ventilating pipe of Supreme/Finolex/Prince working pressure 4.6 kg/cm2 (Four decimal Six kilogram per square centimetre) I.S.I Marked including fixing with approved adhesive etcetra complete including carriage of material within all leads, lifts and other incidentals. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing on wall face PVC (D-plast) rain water pipes of Finolex/Supreme/ Prince of working pressure not less than 4.00/6.00 kg (four to six kilogram) per centimetre square including filling the joints with approved adhesive complete including of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110mm (one hundred ten millimetre) dia PVC plain bend

110mm (one hundred ten millimetre) dia PVC shoe

Providing and fixing steel Clamps ISI Marked of approved design with steel screws and rawal plug etcetra complete within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

110 mm (One hundred ten millimetre) diametre

75 mm (Seventy five millimetre) diametre

Providing and fixing aluminium composite panel (ACP) ceiling 600x600x15mm (Six hundred into six hundred into fifteen) including prepainted G.I. channel framing at the rate of 600mm (Six hundred millimetre) centre to centre complete within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Steel work welded in built up sections of Tata/Sail composed in beams, joists, channels, angles, tees flats with connecting plates or angles, cleats as in trusses and trussed purlins, main and cross beams, hips, jack rafters, purlins connect to common rafter and like work including cutting hoisting fixing in position & applying a priming coat of red lead paint complete including carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Painting two coats(excluding priming costs) on new steel and other metal surfaces with enamel paint of Asian/ Nerolac to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters complete as per PWD specification including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Applying a priming coat over new wood and wood bases surfaces after and including preparing the surface by thoroughly cleaning, oil, grease, dirt and other foreign matter, sand papering and knotting with ready mixed paints of Asian/ Nerolac brushing wood primer pink as per PWD specification including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint of Asian/ Nerolac brushing to give an any shade including cleaning the surfaces of all dirt, dust and other foreign matters sand papering and stopping as per PWD specification including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

6mm (six millimetre) cement plaster 1:3 (one cement isto three sand) in ceiling complete including curing complete as per PWD specification including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (fifteen milimeters) thick cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimetre) in girth, in rough side with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (fifteen milimeter) thick cement plaster in single coat on the fair side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimetre) in girth, in rough side with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (fifteen milimetre) thick cement plaster in single coat on the fair side of brick/concrete/stone walls for exterior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth, with cement mortar 1:5 (one cement isto five sand) complete including curing as per PWD specification including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (fifteen milimetre) thick cement plaster in single coat on the fair side of brick/concrete/stone walls for exterior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth, with cement mortar 1:4 (one cement isto four sand) complete including curing as per PWD specification including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying 20mm (Twenty millimetre) thick Cement plaster with grove in two coats,backing coat 15mm (Fifteen millimetre) and finishing coat 5mm (Five millimetre) thick on rough side of brick/stone masonry walls for exterior plastering upto floor all level including arrises,internal rounded angles,chamfers or rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth complete including curing as per PWD specification including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 2400x1200 mm (Two thousand four hundred into one thousand two hundred millimetre) green chalk board/Black board shall be made of steel of thikness 0.3 to 0.4 mm (zero decimal three to zero decimal four millimetre) It shall have vitreous Enmal coating of 0.095 mm (zero decimal zero nine five millimetre) minimum thickness on top and 0.3 mm (zero decimal three) on the back. top shall be free from waviness and shall show excellient ability. The core material shall be 9mm (Nine millimetre) thik MDF board heaving bluk density of 750kg/cum (Seven hundred fifty kilogram per cubic metre) and grade-1 as per IS : 212406-203 edition 2.2 the backing material sheet shall be min. 0.25mm (zero decimal two five millimetre) thick electro galvanised steel sheet conforming to is: 277-2003. The board shall be fixed on the wall with specially designed J clamps and Sq. clamps with help of Nylon sleves and screws as per site requirement the Government.

Applying Birla white wall care putty over plaster surface after throughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters and sand papered smooth to give final matt finish to the surface complete including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Finishing wall with Apex weather proof exterior emulsion of Asian paint/ Nerolak Suraksha paint/ Berger paint/Dulux paint of approved brand and manufacture and of required shade on undecorated wall surfaces (Two or more coats) to give an even shade after thoroughly brushing the surface to remove all dirt, dust and remains of loose powdered material including cost and carriage of material with in all leads, lifts and other incidentals as per specificatins, approved drawing as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Wall painting (two coats) with Premium emulsion paint of Asian paint / Nerolac Suraksha Paint/ Berger paint / Dulux paint of approved shade for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty required for matting the surface including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Distempering (two or more coats) with acrylic washable distemper of Berger/Nerolac/Asian Paint and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings & other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer as PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Applying two coats of Interior emulsion of Asian paints / Berger paints/ Dulux paints/Nerolac paints (above Dado/skirting) of approved shade for interior painting with brushes plain smooth finish composed of acrylic polymere in emulsion inorganic,/special pigment siliceous aggregate anti fungicides anti-rusting & foaming in two coat including necessary putty to give smooth even surface, sand papered smooth complete as per Architectural drawing ,design and specifications. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Distempering with dry distemper of Asian Paints with white colour of approved brand and manufacture(Two coats)and of required shade on undecorated wall surface to given an even shade over and including primer coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth. as per Architectural drawing ,design and specifications. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing plinth protection with 40 mm (Fourty millimetre) thick interlocking tiles/ cement concrete paver block with 23 cm ( twenty three centimetre) dia half round RCC pipe for drainage purpose laid over 10cm (ten centumetre) concrete 1:4:8 ( one isto four isto eight) in bedding/ haunching complete including cost and carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying 60 mm (Sixty millimetre) thick heavy duty precast cement concrete interlocking paver blocks of NTC with vibro compacted upto M-50 grade including border or kurb block grey or coloured over sub-base of concrete laid over 25mm( twenty five millimetre) thick average thickness of cement mortar 1:4 (one cement isto four sand) and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing & polishing complete (Sub base concrete floor to be measure sepertely including of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and Fixing decorative screen in corridor / verandah manufactured from 19x19mm (nineteen into nineteen millimetre) hollow square pipes welded with M.S. hollow section of size 50x50mm (Fifty into fifty millimetre) supported on brackets made of 25x3mm (Twenty five into three millimetre) M.S flat frame covered with M.S black Sheet as per architectural drawing, design and specifications including of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Forming 15mm (Fifteen millimetre) wide 15mm (Fifteen millimetre) deep groove of uniform size in top layer of plaster as per approved pattern using wooden battens, nailed to under layers including removal of wooden battens, repair to the edges of panels and finishing the grooves complete as per specifications. including of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing polythene aluminium polythene ( PE-AL-PE) composite pressure pipe U.V. stabilized with carbon of KITEC confirming to IS 15450-2004 for water supply including clamps at one meter spacing, cutting fixing and making good the wall etcetra but excluding the cost of fitting internal work pipe exposed on wall complete including entire carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Making connection of galvanised mild steel distribution branch with galvanised mild steel main 20mm (Twenty millimetre) to 40 mm (Forty millimetre) including carraige of materail within all leads, lifts of material and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing high pressure P.V.C spigot and socket soil, waste and ventilating pipe of Supreme/Finolex working pressure not less than 6.0 kg/cm2 (Six kilogram per square centimetre) I.S.I Marked including fixing with approved adhesive etcetra complete including carriage of material within all leads, lifts and other incidentals. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

110 mm (One hundred ten millimetre) diametre

75 mm (Seventy five millimetre) diametre

Providing and fixing PVC ISI Marked clamps with necessary fittings inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre) diametre

75 mm ( Seventy five millimetre) diametre

Providing and fixing PVC ISI Marked heal rest confirming to ISI No.-14735.99 inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre) diametre

75 mm ( Seventy five millimetre) diametre

Providing and fixing P.V.C. of supreme / Finolex/ Prince plain bend Confirming to IS no-14735-99 including filling the joints with approved adhesive. complete inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre) diametre

75 mm ( Seventy five millimetre) diametre

Providing and fixing ISI marked PVC of supreme / Finolex/ Prince collar complete upto all floor level including fixing with approved adhesive complete inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre) diametre

75 mm ( Seventy five millimetre) diametre

Providing and fixing P.V.C cowl of supreme / Finolex/ Prince ISI marked including finishing with approved design with steel screws and rawal plugs etc complete inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre) diametre

75 mm ( Seventy five millimetre) diametre

Providing and fixing PVC Floor Trap ISI marked self cleaning design including fixing with approved adhesive cost of cutting and making good the wall and floor complete.within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110x90 mm ( one hundred ten into ninety millimeters)

110x75 mm ( one hundred ten into seventy five millimeters)

Providing and fixing 110mm (One hundred ten millimetre) size ‘P’ or ‘S’ trap for water closet (squatting pan) including jointing the trap with the pan and soil pipe in cement mortar 1:1 (one cement isto one sand) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing orisa Pan No 20090 of size 53x41 cm ( fifty three into forty one centimeter) vitreous china water closet squatting pan (Indian Type W.C. Pan) of Cera/hindware/ Jaguar of star white/ snow white shade with low level PVC cistern (earth work, bed concrete, foot rest PVC cistern and trap to be measured and paid for separately) including entire carriage of material within all leads, lifts and other incidentals as per direction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing vitreous China wash down water closet (European type W.C. pan) of Constellation No. S No. 20087(S-10) size 57x35x39cm (Fifty seven into thirty five into thirty nine centimetre) with PVC Cistern (Sleek plus) and fixed with jet pressure of Hindware /Cera/ Jaquar of star white / snow white shade with intergal P or S trap including jointing the trap with soil pipe in cement mortar 1:1 (One cement isto one sand) (seat cover and jet spray to be measured and paid for separately) and further as per Architectural drawing ,design and specifications including entire carriage of material within all leads, lifts and other incidentals as per direction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing to wall ceiling and floor high density polyethylene / poly propylene 10 (ten) litres capacity (Dual flush) European standard control low level flushing cistern (Sleek Plus) of Hindware/cera/Jaquar of star white / snow white shade with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm (Fifteen millimetre) nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet,outlet and over flow pipe, 40mm (Forty millimetre) diametre C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) as per Architectural drawing, design and specifications including entire carriage of material within all leads, lifts and other incidentals as per direction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing G.I. inlet connection pipe for each flush pipe with W.C. pan as per Architectural drawing, design and specifications including entire carriage of material within all leads, lifts and other incidentals as per direction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing plastic seal (solid ) and cover of Hindware/ Jaguar/ Cera for wash down water closet with C.P. brass hinges ad rubber buffers (solid type) white plastic seat and cover complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing vitreous China wash basin 55x40cm (Fifty five into forty centimetre) Delta No.10010 of HINDWARE/CERA/JAQUAR of star white/ snow white shade with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing vitreous China urinal flat Back (large) No. 60002 of size 59x37.5x39cm (Fifty nine into thirty seven decimal five into thirty nine centimetre) with auto cistern of make Hindware/Cera /Jaguar of snow white colour including connection with urinal and waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately complete complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing heavy quality stainless steel kitchen sink of approved standard ISI marked with drain board of Diamond/ Unik with C.P. waste pipe, C.I. or M.S. brackets painted white i/c cutting holes and making good the same of size 610x460 (six hundred ten into four hundred sixty millimetre) with bowl depth 200 mm ( two hundred millimetre) including entire carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 32mm (Thirty two millimetre) nominal size diameter rubber plug for wash basin, sink including carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing PVC connection pipe ISI marked 450 mm length 15mm diametre including fitting within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing Mixer for kitchen sink with casted swinging spout at top complete including fitting within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 32mm (Thirty two millimetre) diametre PVC Waste pipe for wash basin or sink including brass check net with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing two hole basin mixing Faucet complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 100mm (One hundred milimetres) nominal size diametre CP grating of ESS/JAL/Kingston for nalhni trap of approved shade complete, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying 150mm (One hundred fifty millimetre) nominal bore/diameters.(to level or slopes) PVC pipes grade 'A' and jointing with approved adhesive including testing of pipes and joints complete, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 600x450mm (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass 6mm (six millimetre) thick of Modiguard/ Atul/ Golden Fish mounted on 6mm (six millimetre) thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. screws and washers including entire carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. brass towel rail size 600x20mm (Six hundred fifty into twenty millimetre) of continental series of Jaguar/Classic of Hindware/ floral series of Cera/Hindon series of Jal with C.P. brass brackets fixed to wooden plugs with C.P. brass screws including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing as per as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing liquid soap container with C.P. Brass lid of Jal//Jaguar/Ess Ess and brackets fixed to wooden plugs with C.P. Brass screws (Plastic container) complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing as per as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing chromium plated brass toilet paper holder of Jal//Jaguar/Ess Ess of approved brand and manufacture complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing as per as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. (Chromium Plated) jet sprey of continental series/clasic series/floral series of Jaguar/ Hindware/ Cera for Europen seat of approved quality and colour with 1.5m (One decimal five metre) tube including carriage of material within all leads, lifts and other incidentals as per specifcations, approved drawing as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm (Fifteen millimetre) diameters C.P. brass bib tap of continental series of Jaguar/ Classic series of Hindware/ Floral series of Cera/ Hindon series of Jal complete as per specifications including carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm (fifteen millimeter) dia CP brass stop cock of OPAL PRIME (Single Lever) series of Jaquar/Fluid (Single Lever) series of Hindware/Ruby (Single Lever) series of Cera/or Oran (Single Lever) series of Kerovit complete as per specifications including carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. brass pillar tap of Continental/Classic/ Florall series of Jaguare/Hindware/Cera 15mm (fifteen millimetre) dia (Heavy duty makes ISI marked No. 8931 & 8934) complete as per specifications including entire carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing PTMT Push cock tap including necessary screws complete as per specifications including entire carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm (fifteen millimetre) C.P. Brass Angle valve of Continental Series of Jaguar contess plus series /Hindware / Ocean series of Nintage series of Kerovite/ hindon series of Jal/ Cera/ Jal as per specifications with nuts & bolts including carriage of material within all leads, lifts, and other incidentals. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. brass full way valve with wheel of continental series/ clasic series/ floral series of Hindware/Jaguar/Cera within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm nominal bore C.P. brass valve (Horizontal plunger) type High pressure with polythene plastic floats of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindson series of Jal with necessary fittings complete including entire carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing PVC connection pipe brass union 450 mm (Four hundred millimetre) length 15mm (Fifteen millimetre) dia ISI marked of including fitting within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 32mm (Thirty two millimetre) diametre C.P. brass waste (Heavy duty make) ISI marked NO-8931 & 8934) of continental series of Jaguar/ Classic series of Hindware/ Floral series of Cera/ Hindon series of Jal for wash basin or sink with in all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing PVC single Equal Branch with oval access door ISI Marked of Supreme/ Finolex with insertion rubber washer 3 mm (Three millimetre) thick bolt and nuts complete including fixing with approved adhesive etcetra Complete including carraige of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre) diametre

75 mm ( Seventy five millimetre) diametre

Providing and fixing PVC Double Equal Branch with oval access door ISI Marked of Supreme/ Finolex with insertion rubber washer 3 mm (Three millimetre) thick bolt and nuts complete including fixing with approved adhesive etcetra Complete including carraige of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre) diametre

75 mm ( Seventy five millimetre) diametre

Providing and fixing PVC door bend with oval access door ISI Marked of Supreme/ Finolex with insertion rubber washer 3 mm (Three millimetre) thick bolt and nuts complete including fixing with approved adhesive etcetra Complete including carraige of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre) diametre

75 mm ( Seventy five millimetre) diametre

Providing and fixing PVC offset 45° ISI marked of supreme / Finolex/ Prince including fixing with approved adhesive etc. complete including fixing with approved adhesive etc. complete including carraige of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimetre) diametre

75 mm ( Seventy five millimetre) diametre

Providing and placing water tank of PVC (Poly venyl chloride) Sintex/Supreme/Finolex (Triple layer) ISI marked having capacity 1000 ( One thousand) litres each with necessary fitting including over flow pipes, scour pipe, ball valve and with cover locking arrangement of good quality including providing pads of sizes as required good quality all complete as per specifications including entire carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:4:8 (One Cement isto Four Sand isto eight) graded stone aggregate 40mm (Forty millimetre) nominal size for bedding of pipes of the 150 mm (One hundred fifty millimetre) internal diameters, necessary form work and curing complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:3:6 (One Cement isto three Sand isto six) graded stone aggregate 40mm (Forty millimetre) nominal size for haunching of pipes of the 150 mm (One hundred fifty millimetre) internal diameters, necessary form work and curing complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 600x120mm (Six hundred into One hundred twenty) glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing Tooth brush and Tumbler holder (Vitreous China) complete with C.P. Brass screws within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Construction manhole with R.C.C. top slab in 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size), foundation concrete 1:4:8 (One cement: Four sand: Eight graded crushed stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm (Fifteen milimetres) thick with cement mortar 1:3 (One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetres) 500mm(Five hundred milimetres) deep, including C.I. cover with frame (light duty single seal pattern–I) 450x610mm (Four hundred fifty into six hundred and ten milimetres) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs(twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 300mm (Three hundred milimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Construction manhole with R.C.C. top slab in 1:2:4 (One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size), foundation concrete 1:4:8 (One cement: Four sand: Eight graded crushed stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm (Fifteen millimetre) thick with cement mortar 1:3 (One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetre nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetre) 1000mm(One thousand millimetre) deep, including C.I. cover with frame (light duty single seal pattern–I) 450x610mm (Four hundred fifty into six hundred and ten milimetres) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs(twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 300mm (Three hundred milimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Constructing brick masonry chamber for under ground CI inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (one cement : five sand) cover with frame (light duty) 355mmx6mm internal dimensions total weight of cover with frame to be not less then 38Kg. (weight of cover 23Kg. and weight of frame 15Kg) RCC top slab with 1:2:4 (one cement : two sand : four graded stone aggregate 20mm nominal size) foundation concrete 1:5:10 (one cement : five sand : ten graded stone aggregate 40mm nominal size) in side plaster 15mm thick with cement mortar 1:3 (one cement : three sand) finished smooth with floating coat of neat cement on wall and bed concrete etc. complete. Inside dimension 455x610x450mm deep single pipe line. The rates are including cost and carriage within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing composit end seal compression fitting as per IS-15450-2004 for water supply including Tee, Albows, reducers/ connectors copluers and clamps with jointing testing and fitting complete including cutting and making good the walls etcetra complete including entire carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Equal Tee (1620)

Equal Tee (2025)

Female Elbow (1620x15mm thread)

Female Elbow (1620x20mm thread)

Female Elbow (2025x25mm thread)

Female Branch tee (1620x1620x20mm thread)

Female Branch tee (2025x2025x25mm thread)

Male thread connector (1620x15mm thread)

Male thread connector (2025x25mm thread)

Reducer tee (1620x all branches)

Reducer tee (2025x all branches)

Coupler (1620)

Coupler (2025)

Reducer tee (1620x1216)

Reducer tee (2025x1216)

Reducer tee (2025x1620)

Providing and fixing composite end seal compression fittings of Kitec as per IS-15450-2004 for hot water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc complete including entire carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Equal Tee (1620)

Equal Tee (2025)

Female Elbow (1620x15mm thread)

Female Elbow (1620x20mm thread)

Female Elbow (2025x25mm thread)

Female Branch tee (1620x1620x20mm thread)

Female Branch tee (2025x2025x25mm thread)

Male thread connector (1620x15mm thread)

Male thread connector (2025x25mm thread)

Reducer tee (1620x all branches)

Reducer tee (2025x all branches)

Coupler (1620)

Coupler (2025)

Reducer tee (1620x1216)

Reducer tee (2025x1216)

Reducer tee (2025x1620)

Providing and fixing Division Plate for urinals 600x300 mm ( Six hundred into three hundred millimetre) of viterous china of Jaguar/ Hindware/ Cera including carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing vitreous China under counter wash basin ISI No.2556 having size 550x400mm (Five hundred fifty into four hundred millimetre) including carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm nominal bore chromium plated urinal spreader complete including carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying to galvanized mild steel tubes (medium grade) 15mm (fifteen millimetre nominal bore/ diametre) including all tube fittings wall sealing and floor of Jindal/TATA Steel nipples, elbows, unions, tees and clamps and within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 20 mm (Twenty millimetre) nominal bore/ diametre to wall ceiling and floor galvanised mild steel tubes of TATA steel/jindal (Hissar) (Medium grade) tube in trenches fittings and clamps including making good the wall, ceiling and floor. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing 40mm (Forty millimetre) thick Cement concrete flooring 1:2:4 (one cement isto two snad isto four aggregate) graded/crushed stone aggregate 20 mm (tewenty milimeter) nominal size mechanically mixed including curing complete as per PWD specification, laid in one layer finished with a floating coat of neat cement. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 455x610mm (four hundred fifty five into six hundred ten millimetre) light duty rectangular C.I. manhole cover with frame cover weight 38KG (thirty eight kilogram) (single seal pattern-I) including entire carriage of material within all leads, lifts and other incidental, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing & Fixing water lifting pump ( Tolu pump ) of Havells / Usha / Crompton / Kirloskar 1.00 H.P centrifugal head range 6 - 25 (Six to Twenty) meter 20mm (Twenty millimetre) nominal bore making necessary connection, fittings and accessories as required including carraige of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing 200 mm (Two hundred millimetre) wide cast iron rugs with chequered or rubbed non slip surface including fixing in man holes with 200x200x100 mm (Two hundred into two hundred into one hundred millimetre) cement concrete 1:3:6 (one cement isto three sand isto six graded /crushed stone aggregate) 20 mm (Twenty millimetre) nominal size complete including carraige of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Mahesh Sharma

vikas parmar