SPECIAL REPAIR TO BLDG NO. P 5 AND P 43 AT NHO UNDER AGE B R III OF GE CLEMENT TOWN DEHRADUN

Amount

Demolition of cement concrete (Un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, jambs etcand removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section in any position complete all as specified and directed by Engr-in-Charge.

Dismantling of Asbestos cement (corrugated, semi corrugated etc.) sheets as in roof coverings complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Taking down cement plaster of any description on brick work or stone masonry walls including rackingout joints, hacking for key, scrubbing down with water etc and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size n.exc 1.50 Sqm complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size exc 1.5 Sqm and n.exc 4 Sqm complete all as specified and directed by Engr-in-Charge.

Taking down shutter of any description exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed by Engr-in-Charge.

Taking up or down 15mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed by Engr-in-Charge.

Taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete type C2 1:3:6 (using 40mm graded stone aggregate) as in surface channels and drains finished fair and even complete all as specified and directed by Engr-in-Charge.

M&L brick work with sub class "B" old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engr-in-Charge.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa (AZ -150) as in roof covering/cladding to wall, fixed with self tapping screws and washers of 68 mm fine thread for MS Pipe purlin and double threaded for wooden purlins as per sutaible distance as guided by AGE/ GE and finally complete all as Specified & directed by GE/Eng-in-Charge.Make - Tata Durashine , JSW steel India or equivalent in Roffit( Shiv Shakti Fibre Udyog)

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa (AZ- 150) as in ridges, hips, valleys/rain water / roof covering/cladding to wall, fixed with self tapping screws and washers of 68 mm fine thread for MS Pipe purlin and double threaded for wooden purlins as per sutaible distance as guided by AGE/ GE and finally complete all as Specified & directed by GE/Eng-in-Charge.Make - Tata Durashine , JSW steel India or equivalent in Roffit( Shiv Shakti Fibre Udyog) )

S&F mild steel work as in trusses, rafters, purlins etc, and the like made out of MS pipe, flat, angle or hollow sections conforming to Fe-410-W (Gde-E-250) quality-A incl all necessary cleats, gusset plates etc complete all as specified and directed by Engr-in-Charge.

M&L Mild steel framed work such as grills, gratings etc disigned with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings framework of water tanks and similar work confirming to Fe-290 Gde E-165 and making good to disturbed area of Brickwork & concrete surface including plastering with two coats of white wash complete all as specified and directed by Engr-in-Charge.

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L RCC (1:2:4) type B-1 (Using 20mm graded stone aggregate) as in slabs, shelves supported on walls, beams and columns in floor or roof including balconies, canopies, deck slabs or in Chajja/facia projection and the like complete all as specified and directed by Engr-in-Charge.

M&L mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

M&L for use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for fair finished surfaces (Horizontal or sloping) complete all as specified and directed by Engr-in-Charge.

M&L for Vitrified any design and pattern coloured tiles scratch proof and stain resistance double charged (water absorption not more than 0.5%) 9-10mm thick (square/ rectangular) area of each tiles exc 0.42 Sqm but n.exc 1.00 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6 complete. Tiles shall be comfirming to IS-15622.2017, Group B1 complete breaking strength 1300 N (Minimum) all as specified and directed. Note :- Shade of the tiles including Colour, Design and pattern shall be apporved by GE. all as specified and directed

M&L for Vitrified any design and pattern coloured tiles scratch proof and stain resistance double charged (water absorption not more than 0.5%) 9-10mm thick (square/ rectangular) area of each tilesexc 0.42 Sqm but n.exc 1.00 Sqm as in vertical surface such as dado/ skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 to recieve tiles complete. Tiles shall be comfirming to IS-15622.2017, Group B1 complete breaking strength 1300 N (Minimum) all as specified and directed. Note :- Shade of the tiles including Colour, Design and pattern shall be apporved by GE. all as specified and directed.

M&L for Non skid Endura coloured tiles 8-10mm thick (square/rectangular) grade-4, area of each tile exc 0.06 Sqm but not exc 0.11 Sqm over and including 15mm thick screed bed in Cement mortar (1:6) in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge. (Make : Johnson Endura, Orint) Note :- Shade of the tiles including Colour, Design and pattern shall be apporved by GE.

M&L for Glazed ceramic coloured joint free tiles of any design and pettern, 450x300X7 to 8mm as in dedo vertical surfaces over and including 10mm thick rendering in Cement mortar (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles. Tiles shall be comfirming to IS-15622.2017, Group B III complete all as specified and directed. Note :- Shade of the tiles including Colour, Design and pattern shall be apporved by GE.

M&L for Wall Cladding tile 7-8mm thick area of each tile exc 0.10 sqm but n.exc 0.20 Sqm of any colour and pattern set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering on wall in CM 1:4 and surface finished even & fair Complete all as specified and as directed by Engr-in-charge.

M&L for 18-20mm thick pre polished granite stone slab (apparant density not less then 2700 kg/cum of any colour) as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust to match with marble shade over and including cement screed bed 15mm thick in CM (1:6) complete all as specified and directed by Engr-in-Charge.

S&F 30mm thick factory made flush shutter solid core construction with block board core and ply wood face panels, commercial type both sides complete all as specified and directed by Engr-in-Charge. Make : Kit Ply wood/Green/Century ply.

S&F Factory made 100% Solid WPC Brown door Frame (75mm x 50mm Single Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge. Make : Eco Cell, Floresta, Raj Shree Plastic Wood & Archid Lam

S&F Factory made 100% Solid WPC Brown door Frame (125mm x 63mm Double Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge. Make : Eco Cell, Floresta, Raj Shree Plastic Wood & Archid Lam

S&F 24mm thick Moulded WPC Brown Factory made 100% Solid door (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture and back side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and directed by Engineer-in-Charge. Make : Eco Cell, Floresta, Raj Shree Plastic Wood & Archid Lam

S&F 30mm thick Moulded WPC Brown Factory made 100% Solid door (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture and back side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and directed by Engineer-in-Charge. Make : Eco Cell, Floresta, Raj Shree Plastic Wood & Archid Lam

S&F 30mm thick Factory made Wiremesh SOLID PVC Door Shutter Consisting of frame made out of M.S.tube of 19 guage thickness and size of 19mm x 19mm for stiles and 15mm x 15mm for top, lock & bottom rail. M.S Frame shall have a coat of metal primer of approved make and manufacturer 19mm x 19mm M.S square tubes shall be covered with 5mm thick PVC heat moulded (100% LEAD FREE) plain sheet 'C' channel 75x30x60 out of 10mm shall be heat at 90 deg. towards inner site of both site of both face of the door forming stiles for top, bottom, lock rails shall be fitting of 10mm inner site all rails (T,B lock) shall be covered with 100mm wide PVC sheet S.S wire mesh shall be fixed with 15x15 square tube in side rails with screwing 8x28 heat metal zinc coated screws can be remove or fix again after changing of wire mesh when needed complete all as specified and directed by Engineer-in-Charge.Make : Eco Cell, Floresta, Raj Shree Plastic Wood & Archid Lam

S&F Aluminium powder coated three track sliding windows (with three sliding shutters, (One with and incl stainless steel wire mess and two with and incl 4mm thick sheet glass panes) aluminium sections not less than 1.1kg per meter for bottom track and top track and side track 0.98 kg per metre, bottom shutter frame 0.55 kg per metre, top shutter frame 0.47 kg per metre, shutter sides, 0.47 kg per metre and interlock sides 0.45 kg per metre including suitable nylon beading channel gasket, nylon rollers Maruthi lock with handles etc complete all as specified and directed by Engr-in-Charge.

S&F Aluminium powder coated fixed glazing with aluminium frame of weight not less than 1.2 kg/m with and incl 8 mm thick glass (plain/ tinted) of size as directed by the Engineer-In-Charge including suitable nylon beading channel gasket, etc complete all as specified and directed by Engr-in-Charge. Make- Antelio glass of Saint Gobain

S&F 18mm thick with min density 600 Kg/Cum LEAD FREE PVC Celuka ply of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet siders top and bottom and shelvers inside the cabints complete as per manufacturer's specifications complete all as specific and directed. Make Raj Shree Plastic wood/Sintex/Archid Plywood/ Kumar Arch Tech Ltd, Eco Cell.

S&F 18mm thick with min density 600 Kg/Cum LEAD FREE PVC Celuka ply of singel side rigid laminate of approved colour adn other side plain white colour fixed with ss screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet shutters complete as per manufacturer's instructions complete all as specific and directed. Make Raj Shree Plastic wood/Sintex/Archid Plywood/ Kumar Arch Tech Ltd, Eco Cell.

S&F of 100mm long stainless steel non megnetic butt hinges, medium weight cold rolled complete all as specified and directed by Engr-in-Charge.

S&F 150mm long, stainless steel non megnetic barrel tower bolts complete all as specified and directed by Engr-in-Charge.

S&F 100mm size stainless steel non megnetic handles, all as directed complete all as specified and directed by Engr-in-Charge.

S&F 150mm size Stainless Steel handles, all as directed complete all as specified and directed by Engr-in-Charge.

S&F of 250mm long (Length of bolt) stainless steel non megnetic sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, and fixing bolts and sliding bolt complete all as specified and directed by Engr-in-Charge.

S&F in repair Hydrulic/Auto Self Closing hinges 35mm of crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters stainless steel non megnetic complete in all respect and fixed in position all as specified

S&F in repair door closer aluminium ISI mark (extruded section) body hydraulically regulated, designation No. 3, universal type, complete all as specified and directed by Engr-in-Charge.

S&F in repair of 140mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate complete all as specified and directed by Engr-in-Charge.

S&F Window blind is made up of several long horizontal or vertical slats of various types of hard material, including wood, plastic or metal which are held together by cords that run through the blind slats or roller window blinds made up of thermal fabric with roll up blinds mechanism, plain or printed type, of design and shade as approved by the Engineer-In-Charge complete with all connected fittings and fixtures incl taking down old drapery rods/ pelmets complete all as specified and directed by Engr-in-Charge.

S&F 20mm dia Stainless Steel curtain rod fixed to wall with neccesary brackets and decorative knobs complete all as specified and directed by Engr-in-Charge.

M&L 15mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 15mm thick rendering cement mortar (1:4) mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed by Engr-in-Charge. (WPC shall be paid seperately)

M&L for 10mm thick plaster on roof, chajja, ceiling and roof parapet of CM (1:3) on RCC finished even and smooth without using extra cement etc complete all as specified and directed by Engr-in-Charge.

Supply only liquid water proofing compound ISI Marked complete all as specified and directed by Engr-in-Charge

M&L for preparation of old decorated surface of internal wall by removing existing treatment with mechanical sander (rpm 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers and applying two coats of acrylic distemper using roller all as specified and prescribed by manufacturer of paint and all as directed at site by Engr-in-Charge. Note :- (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per manufacture's instruction before application of distemper. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. (ii) After carrying out preparation of surface the same shall be got approved from GE before application of distemper for each building. (iii) The colour/shade will be all as approved by GE.

M&L for Preparation of old surface on ceiling including brooming down or steel wire brushing scraping down smoke soot, muulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of white wash on old decorated surface complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old decorated surface of exterior wall by removing existing treatment with mechanical sander (rpm 1500-2700) along with dust extraction system for clean environment certified by reputed paint manufacturers, then washing the surface with Bleaching poweder solution for treatment of fungal growth and applying two coats of exterior anti fungal acrylic emulsion paint (wallmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of perfomance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint and as directed at site by Engr-in-Charge. Note :- (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacture instruction before application of distemper. The cost of materials, labour & T&P required for preparation of surface are demand to be included in the rates quoted. (ii) After carrying out preparation of surface the same shall be got approved from GE before application of distemper for each building. (iii) The colour/shade will be all as approved by GE.

M&L for preparation of newly plastered surface on internal walls and applying two coat of acrylic distemper (Oil emuision) over one coat of primer using rollers of approved tint and make all as specified and directed by Engr-in-Charge.

M&L for two coats of white wash to newly plastered surface including preparation of surfaces complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered surface of external wall all as prescribed by manufacture of paint and applying two coats of exterior anti fungal acrylic emulsion paint (walmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint and as directed as site by Engr-in-Charge. Note :- (i) The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacture instruction before application of emulsion paint. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. (ii) The colour/shade will be all as approved by GE. (iii) The cost of scaffolding wherever required are deemed to be included in the rates quoted by the contractor. (iv) After carrying out preparation of surface the same shall be got approved from GE before application of distemper for each building.

M&L for preparing new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint of any tint over one coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

S& F for GI tubing 15mm bore, medium grade ISI marked with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions, including short lengths etc.) ( heavy grade ISI Marked) , fixed to walls, concealed in wall and ceiling or laid in floor complete complete all as specified and directed.

S& F for GI tubing 20 mm bore, medium grade ISI marked with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions, including short lengths etc.) ( heavy grade ISI Marked) , fixed to walls, concealed in wall and ceiling or laid in floor complete complete all as specified and directed.

Refixing of old steel tubing and connections in new or old position with all fittings to floor, wall or ceiling for 15mm bore GI tubing complete all as specified and directed by Engr-in-Charge.

Refixing of old steel tubing and connections in new or old position with all fittings to floor, wall or ceiling for 20mm bore GI tubing complete all as specified and directed by Engr-in-Charge.

Cutting chases, pinning in, making good to facing where required and pointing in Cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water pipe etc and making good, cutting not exc 10cm width or girth complete all as specified and directed by Engr-in-Charge.

S&F in repair 20mm dia gun metal gate valve ISI mark class 150 with iron wheel haeded screwed both ends to iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair 75mm dia PVC (SWR) pipe ISI mark single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and directed by Engr-in-Charge.

S&F in repair 75mm dia PVC (SWR) floor trap with grating including jointing with solvent cement including fixing waste pipe etc complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC vent cowls 75mm complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC connection 15mm bore dia 450mm long with 2 Nos PTMT nuts with washer complete all as specified and directed by Engr-in-Charge.

S&F in repair 20mm dia brass CP tubular towel rail D type 600mm long complete all as specified and directed by Engr-in-Charge.Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make : Jaquar Cat Part No AKP-35711PS, Cera Cat Part No F-5006103, Hindware Cat Part No F-840013

S&F in repair bib tap cast cooper alloy with crutch or butter fly handle, 15mm bore screwed for iron pipe complete with wall flange complete all as specified and directed by Engr-in-Charge.Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make :- Jaquar Cat Part No FUS 29037, Parryware G-2304A1 and Cera F1014151.

S&F in repairs 15mm pillar taps cast coper screwed for iron pipe and fixed complete all as specified directed.Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make :- Cera cat part No QT F2006103, Hindware cat part No F-320001 , Jaquar Cat Part No FUS-29001.

S&F Sinks ISI mark made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm and bowl size 410mm x 330mm x160mm complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm dia brass CP Sink mixer with swinging spout (wall mounted model) with connecting legs and wall flanges screwed down for iron pipe and fixed complete all as specified and directed. Make : Jaquar Cat Part No CQT-CHR-23309B or equivalent quality in perryware or cera.

S&F 15mm Brass CP wash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make : Jaquar Cat Part No FUS 29037, Hindware F280010SCD, Cera F-2013451.

S&F in repair CP health faucet with 1m flexible tube and wall hook complete all as specified and directed.Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make : Jaquar Cat Part No ALD-573, Hindware 160027, Parryware-T-99408.

S&F in repair CP angular stop cock 15mm dia single way and fixed complete all as specified and directed by Engr-in-Charge.Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make :- Jaquar Cat Part No FUS-20953, Hindware Cat Part No F-320006, Perryware-G-4907A1.

S&F in repair CP toilet paper holder fixed to wall with CP brass screws complete all as specified and directed. Make : Jaquar Cat Part No AKP-35751, Hindware Cat Part No F-880003, Parryware-T-6514A1.

S&F in repair Sheet glass shelf assembly/Glass Corner assembly set of three consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr-in-Charge. Make :- Jaquar Cat Part No ACN-1171N, Cera Cat Part No-F-5005301, Parryware-T-6009A-1.

S&F in repair vitreous china WHB size 505x410x185mm with full pedastal, white with flat back including CP waste coupling and all as specified and directed by Engr-in-Charge.Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make :- Jaquar Cat Part No AIS-WHT-101801, Hindware Cat Part No -11032

S&F in repair Vitreous china white wash down couple closet composite type including PVC soft seat cover white complete all as specified and directed by Engr-in-Charge.Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site. Make : Jaquar Cat Part No LYS-WHT-38853S, Hindware Italian Cat Part No 92509 (S-30) Cera Cat Part No S1013132 S.

S&F in repairs Kitchen Plate rack ISI mark with and including shelves and hanging arrangement for utensil for kitchen, made of stainless steelsheet 0.63mm thick size 24"x24"x10" complete all as specified and directed by Engr-in-Charge.

S&F in repairs PVC water storage tank double layer cylindrical, vertical with closed top with threaded cover hoisted and fixed in position tank capacity 500 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 20mm bore of iron pipe and making connection for inlet and outlet including dismantle of old water tank and removing from site complete all as specified and directed by Engr-in-Charge.

M&L for joint free Non-skid ceramic coloured tiles of any deisgn and pattern 7-8mm thick (square/rectangular), area of each tile exc 0.06 sqm but not exc 0.11 Sqm in floor etc, including 15mm thick screed bed in CM (1:6) in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles. Tiles shall be comfirming to IS-15622.2006. Group B II Grade-IV Complete all as specified and directed. Note :- Shade of the tiles including Colour, Design and pattern shall be apporved by GE.

Dismantling and taking down U/S copper / aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified and directed. Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Dismantling and taking down old damaged existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified

Material & Labour for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with contineous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed PVC conduit ,duly concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia (Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover cover plate complete all as specified and directed. Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

One 3pin/5pin 5/6 Amps socket out let on same board with other switches , with cables 1.5 sq mm size , complete all as specified and directed.

One 3pin/5pin 5/6 Amps socket out let on independent board with other switches, with cables 1.5 sq mm size, complete all as specified and directed .

All as per item No 89 above but with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point.

All as per item No 89 above but with 4 Sqmm PVC insulated cable (FRLS )and same size of earth wire for 15 Amps power point.

S & F Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge. Make: Legrand Cat No: 673401/ Indoasian Cat No: 800000 or equivalent make of L&T/Havells.

Supply and fixing switch modular , one-way 16Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge. Make: Legrand Cat No: 673411/ Indoasian Cat No: 800002 or equivalent make of L&T/Havells.

Supply and fixing modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz all as specified and directed by Engr- in-charge. Make: Legrand Cat No: 673452/ Indoasian Cat No: 800020 or equivalent make of L&T/Havells.

Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed by Engr- in-charge. Make: Legrand Cat No: 6734585/ Indoasian Cat No: 800022 or equivalent make of L&T/Havells..

Supply and fixing bell push modular flush type single pole one way 6 Amps, 1 module all as specified and directed by Engr- in-charge. Make: Legrand Cat No: 673404/ Indoasian Cat No: 800007 or equivalent make of L&T/Havells..

Supply and fixing step socket type modular fan regulator 120/280 V , 2 module all as specified. Make -Legrand, Cona/ SSK/Hair,

Supply and fixing bell ding dong AC 230/240 Volts single pole

Supply and fixing ceiling rose surface bakelite 65x25mm dia having three terminals all as specified Cat Part No HSN8536/39072 of Anchor, HSN 8536/2116 of Cona or equivalent in havells.

Supply and fixing batton/angle holder insulated body with back plate, suitable for batten fittings all as specified & directed. HSN8536/38538 of Anchor, HSN 8536/3966 of Cona or equivalent in havells

Supply and fixing in repair energy efficient LED lights fitting, 9 watt , 230 Volt, of 600 mm length,CCT 6000ºK to 6500° K , decorative ultra slim linear LED lighting fixture with extruded aluminium housing heat sink, environmental friendly, energy efficient LED light source more than1200 lumens , wall mounted mirror batten, integrated electronic driver, system efficacy not less than 140 lumens /watt CCT 6000 to 6500°K , surge protection range ≥ 2.5 KV , voltage protection range 120-300 volt AC, power factor > 0.95 total harmonic distortion < 20%, colour rendering index > 80, fixed on site with all accessories including 2 years warranty connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & as directed. Make Shakti/ Havells/Crompton.

Supply and fixing in repair LED lights fitting 1X18 watt ,4 ft with extruded aluminium housing heat sink, environmental friendly energy efficient translucent diffuser with LED light source,2400 Lumens( minimum) coefficient colour temp 6000°K to 6500 °K, surge protection range ≥ 2.5KV, voltage protection range-120-300VAC,2 years warranty ,system efficacy not less than140Lm/Watt for the fitting, power factor >.95,total harmonic distortion< 20% color rendering index>80, fixed on site with all accessories including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose all as specified & directed cat No. Make Shakti/Havells/Crompton

Supply and fixing sheet metal enclosure double door type for MCBs DB TPN 415V AC 4 way with 200 Amps rated bus bar. all as specified and directed .Make- legrand / ABB/ Schnider

Supply and fixing MCB SP 5 to 32 Amp 'B' series 10 KA repturing capacity complete all as specified. Make -Legrand , ABB/ Schnider

Supply and fixing MCB TPN 40 Amps 240 V 10 KA repturing capacity all as specified. Make -Legrand, ABB/ Schnider

Supply and fixing single pole and neutral enclosure with a two pole and earth plug socket complete with 01 No, RCCB 25 Amp, 30 mili amps, DP, 240 Volts, AC Complete all as specified. Make - Legrand, ABB, Schnider. (Note - Cost of cutting chases for enclosure concealed in wall of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 12 way with 200 Amps rated bus bar all as specified and directed .Make- legrand / ABB /Schnider

Disconncetion of existing ceiling fans/ wall fans and refiing the same after complete of repair work

S & F PVC fresh air fan 240 volts Ac 50 Hz 250 mm sweep PVC body including louvers and cutting as required size and shape complete all as directed. Make: Bajaj/Havells/Crompton

S & F exhaust fan 240 volts Ac 50 Hz 300 mm sweep matellic body (RPM will not be more then 900) including louvers and cutting as required size and shape complete all as directed. Make: Bajaj/Havells/Crompton

Supply and install electric water heater storage type geyser (ISI mared) 5 star rated inner container with Stainless steel 1500 watt of capacity 25 Ltr complete grouting on wall with suitable size of nut & bolts washer as srequired at site all as specified and directed. Make:Bajaj/Havells/Crompton

Supply and fixing sub main wiring two single core 4 sq mm PVC insulated unsheathed multi stranded copper conductor cable ( FRLSH ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade surface/ concealed in wall as per existing along with 4.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLSH ) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and as directed Note:- Two runs of multi stranded copper conductor cable and one run of earth wire including PVC conduit will be measured as a one length.

M/S Manmohan Singh Anand