C/O R.M. Sub Yard at Guler Distt. Kangra, H.P. SH- C/O Septic tank, sock pit and W.S. and S.I. Work.

Amount

Excavation in foundations, trenches etc. in earth work in all kinds of earth work including spade work as pick work, jumper work, blasting work including where blasting is prohibited and chiselling / wedging out of rock and their intermediate classification of soil including dewatering whereever required upto all leads & lifts and stacking the excavated soil not more than 3 meteres clear from the edge of excavation and than returning the stacked soil in 15 cms layers, when required into plinths, sides of foundations etc.consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth the dumping site through all mode of transportation including head load animal load or mechanical means alongwith its leveling at dumping site and complete the work by mechanised means and labour (if any required) furtherany loss of the public and private property during the course of execution shall be the absoutely responsibility of the contractor which shall have to duly compemsated by him in all respect as will be decided by the Engineer-in-Charge.

Providing form work with steel plates 3.15mm (three point one five millimetre) thick welded with angle iron in frame 30x30x5mm ,so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden / steel battens and ballies, height of propping and centring below supporting floor to ceiling up to all heights and removal of the same for insitu-reinforced concrete & plain concrete work including carriage of material within all leads and lifts as per direction of Engineer-in-charge in:- Beams, cantilever, girders and lintels:- Side and soffits of beams, beam haunchings, cantilevers bressumersand lintels not exceeding 1meter in depth in all heights from floor.

Edges of slabs and bricks in floors and walls under 20cm wide. including carriage of material within all leads and lifts as per direction of Engineer-in-charge in:-

Flat surfaces such as soffits of suspended floors, roofs, landing and the like.Floors etc. upto 200mm inthickness including carriage of material within all leads and lifts as per direction of Engineer-in-charge in:-

Providing and laying mechanically mixed and vibrated cement concrete Mix 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers in all heights & all floor level. including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and laying Mechanically mixed & vibrated cement concrete 1:6:12 (1: cement :6 sand: 12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of from work in foundation and plinth, including carriage of material within all leads and lifts as per direction of Engineer-in-charge

Random rubble masonry/polygonal rubble masonry (Uncoursed/brought to courses) with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1Cement : 6 Sand : 12 Graded stone aggregate 20mm nominal size) at plinth level in cement mortar 1:6 (1 Cement : 6 Sand) including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

C/o Dry rubble masonry in breast wall and retaining walls revetment walls and parapets etc. including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing mild steel / tor steel reinforcement for R.C.C. work including binding wire, cutting, bending, binding and placing in position complete upto all floors level including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Second class Half brick masonary in common burnt clay building bricks in foundation and plinth in all floor levels in cement mortar 1:4 (1 cement : 4 sand) including carriage of material in all leads and lifts :- Second class brick

Providing and laying mechanically mixed and vibrated cement concrete Mix 1:2:4 (1cement :2 sand :4 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work in foundation and plinth: including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior / exterior plastering upto all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 30cm in girth and finished even and smooth including carriage of material within all leads and lifts in all floor levels as per direction of Engineer-in-charge in Cement mortar 1:3 (1 cement : 3 sand).

Filter material behind retaining wall complete as per drawings & technical specification clause 1204.3.8 with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (medium grade) of Jindal (Hissar) or equlent tube fittings ISI and clamps including making good the wall, ceiling and floor 15mm nominal bore including carriage of material within all leads and lifts as per direction of Engineer-in-charge.15mm nominal bore.

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (medium grade) of Jindal (Hissar) or equlent tube fittings ISI and clamps including making good the wall, ceiling and floor 15mm nominal bore including carriage of material within all leads and lifts as per direction of Engineer-in-charge.20mm nominal bore.

Providing and fixing 75 mm high pressure PVC (Finolex) spigot and socket waste and ventilating pipes ISI marked including fixing with approved adhesive etc. Complete, including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing 110 mm high pressure PVC (Finolex) spigot and socket waste and ventilating pipes ISI marked including fixing with approved adhesive etc. Complete, including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing PVC ( FINOLEX) door bend with oval access door insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. Complete ,with in all leads, lifts of materials as directed by the Engineer-in-Charge.75 mm dia,

Providing and fixing PVC ( FINOLEX) door bend with oval access door insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. Complete ,with in all leads, lifts of materials as directed by the Engineer-in-Charge. 110 mm dia.

Providing and fixing PVC ( FINOLEX) single equal branch (a) with oval access door, ISI marked insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive etc. complete ,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. 110 mm dia

75 mm dia door tee.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete. 110 mm dia with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete. 75 mm dia with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing & fixing cast iron cowl 75mm nominal dia metre with in all leads, lifts of materials as directed by the Engineer-in-Charge

Providing and fixing vitreous China wash down water clost squaatting pan (Indian type W.C. Pan) size 580mm (Earth work bed concrete foot rest and trap to be measured and paid for separately) Orissa Pattern including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing vitreous china bowl pattern urinal Cera/Hindware make or its equivalent including connection the urinal with waste pipe by means of white lead mixed with chopped hemp ( Wast pipe to be measured and paid for separately )flat back type size 430mmx260mmx350mm, within all leads, lifts of materials and other incidentals as per approved drawing design and as directed by the Engineer-in-Charge.

Providing and fixing vitreous china wash basin Hidware make or equivalent with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings flat back 630 mm x 450 mm., with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 600 mm x 450 mm bevelled edge mirror of superior glass mounted on 6 mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws & washre of aproved make with in all leads, lifts of materials as directed by the Engineer-in-Charge.

Providing and fixing 600 mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete of approved make fixed to wooden plugs with C.P. Brass screws.with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws 600mm x20mm, with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge

Providing and fixing chromuim plated brass soap dish with C.P brass bracketsw fixed to wooden cleats with C.P Brass screws with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing PTMT (Paryag make) coloured/white high density polyethylene /poly propylene 10 litres capacity (full flush) European standard control low level flushing cistern ISI marked with fittings with a pair of brakckets with fitings such as lead valve syphon 15 mm nominal size PVC ball valve with polythene float with push button couplings for connections with inlet outlet and over flow pipe 40 mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of materials with in all leads & lifts as per direction / satisfaction of the Engineer-in-charge.

Providing and fixing PTMT Coloured/white automatic flushingl cistern with a pair of PVC/C.I. Or M.S. Bracket complete with fittings including PVC syphonic apparatus mosquito proof lid PVC union and coupling for connections with inlet outlet and over flow pipes including cutting holes and making good the same (over fow pipe to be measured and paid for separately), including carriage of material within all leads and lifts as per direction of Engineer-in-charge. 5 litres net capacity.

Providing and fixing PTMT (Paryag Make) angle valve with Nuts and pipe 15 mm dia including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

providing and fixing 32mm dia lead waste pipes for wash basin and sink including brass checknut.including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing C.P. Brass waste for wash basin or sink 32 mm dia with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing Hot water P.V.C. connection pipe with brass Unions including carriage of materials in all leads and lifts. 45cm length, 15 mm nominal Bore.

Providing and fixing C.P. Brass bib tap of Seiko make or its equivalent with capstan head 15mm dia. with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing C.P. Brass pillar tap of Seiko make or its equivalent with capstan head 15 mm dia with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing division plate for urinals 600mm*300mm vitorious china with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Making connections of galvanised steel distribution branch with galvanised mild steel main 20 mm to 40 mm nominal bore by providing and fixing tee including cutting and threading the pipes complete, with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge

Constructing manhole with R.C.C top slab in 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) :- (i) Inside size 800mm x 800mm and 1000mm deep including C.I cover with frame cover (light duty single seal pattern-1) 455mm*610mm internal diamansion total weight of cover and frame tobe not less than 38kg ( weight of cover 23kg and weight of frame 15kg) with 200mm thick walls of brick masonry using common brunt clay building bricks in cement mortar 1:3 (1 cement 3 sand) complete including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing PVC water storage tank of ISI 12701 marked G.I. inlet and outlet connection 15 mm nominal bore ball valve and mosquito proof PVC cover with locking angement including hoisting up to all heights above ground level 1000 litres net capacity tank .including carriage of materials with in all leads & lifts as per direction / satisfaction of the Engineer-in-charge .

Providing and fixing brass full way valve with wheel / PVC coated lever complete including carriage of material within all leads and lifts as per direction of Engineer-in-charge:- 15 mm nominal boire.

Providinga and fixing brass full way valve with wheel 15 mm nominal bore , with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge

Providinga and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting and making good the wall and floor etc. complete 110 mmx 75 mm with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 100mm size P or S trap for water closet ( squatting pan) including jointing the trap with the pan and soil pipe in cement mortar 1:1 (1 cement 1 sand) vitreous china in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P waste with C.I or M.S brackets painted white including cutting holes and making good the same but excluding fitting. 610*460 mm with bowl depth 200mm all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Sandeep Mehra