Construction of Administrative building of Thana/Barrack at Bhuta in Distt. Bareilly.

Amount

Excavation in foundation in ordinary soil, loame, clay or sand including lift upto 1.5 m & Iead upto 30m Including filling watering & ramming of excavated earth into the trenches or into the space between the building & the sides of foundation trenches or in to the plinth removal & disposal of surplus earth as directed by the engineer in charge upto a distance of 30m from the foundation trenches. (Excluding Royalty). SOR-251

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2. (Carted earth lead 2 Km)

Cement concrete with 4 cm. (1½") gauge approved stone, ballast, approved coarse sand and cement in the proportion of 8:4:1 including supply of all materials, labour and T&P etc. required for proper completion of the work Sor no -281.

Sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8 km. from the site of work & including watering,dressing etc. Rate includes cost of all materials, labour and T&P etc. required for proper completion of the work.(including royalty) SOR-255

Providing and injecting chemical emulsion for preconstructional antitermite treatment and creating and chemical barrier under and around the columns pits, wall trenche basement excavation top surface if plinth filling junction of wall and floor along the external per meter of binding expension joints surrounding of pipes and conduit ete. Complete (Plinth area of the building at ground floor only shall be measured as per I.S.6313(part ii 1981). Aldrine emulsificable concentrate of any other approved material such as Hepthachlor or chlordance will be used. The rate of application of chemical emulsion shall be as follows. i)Treatment for masonry and foundatrion 5 litres per sqm ii)Back fill in immediate contact with foundation 7.5 liters/sqm. iii)Treatment of top surface of plinth filling 5 liters per sqm iv)Treatment junction of soil along extemal per meter building 7.50 litre/sqm. v)Treatment of soil under apron along extemal perimeter 5 Iiter/ sqm. CH-8

R.C.C. work with cement approved coarse sand and 2 cm (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 in in slabs excluding supply of reinforcement and its binding but including its fixing and binding the same with 24 B.W.G.G.l. binding wire and includuing Necessary centering and shuttering etc.and also including supply of all materials, labour and T&P etc. required for proper completion of the work. Binding wire cost being included in the item. SOR 284A

R.C.C. work with cement approved coarse sand and 2 cm (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 in in lighter beams having span up to 6.00 m excluding supply of reinforcement and its binding but including its fixing and binding the same with 24 B.W.G.G.l. binding wire and includuing Necessary centering and shuttering etc.and also including supply of all materials, labour and T&P etc. required for proper completion of the work. Binding wire cost being included in the item. SOR-285

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

R.C.C. work with cement approved coarse sand and 2 cm (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 in R.C.C Column excluding supply of reinforcement and its binding but including its fixing and binding the same with 24 B.W.G.G.l. binding wire and includuing Necessary centering and shuttering etc.and also including supply of all materials, labour and T&P etc. required for proper completion of the work. Binding wire cost being included in the item. SOR-289

First class brick work in 1:6 cement and coarse sand mortar in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of the work. SOR NO 303

Painting in D.P.C. with two coats of airblown bitumen 85/50 or 85/25 @ about 1.7 kg./sqm including cost of fuel if any. NEW ITEM-1

First class brick work in 1:6 cement and coarse sand mortar in super structure including supply of all materials, labour and T&P etc. required for proper completion of the work. but in super-structure, including necessary cutting and moudling of bricks as required and including honey comb brick work, thickness of wall 1 brick thick . Sor item no. 303+309+310

First class brick work in 1:6 cement and coarse sand mortar in super structure including supply of all materials, labour and T&P etc. required for proper completion of the work. but in super-structure, including necessary cutting and moudling of bricks as required and including honey comb brick work, thickness of wall ½ brick thick . SOR item no. 303+309+310a

Mild steel or iron in plain work such as reinforced concrete or reinforced brick work (when not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of all steel and wastage and over lapping & hooks. SOR NO 504

15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand) DSR-13.5.1

12 mm thick plaster with Kankar lime over brick work minimum thickness not to be less than 3/8" (10 mm) thick including supply of all materials, labour and T&P etc. required for proper completion of the work. but with cement and fine sand of 1.25 F.M. mortar in 1:6. SOR-586+584i-584+596

12 mm cement plaster of mix. 1:6 (1 cement: 6 fine sand) including supply of all materials T&P etc required for proper completion of the work. SOR NO- 586+584i-584

12 mm cement plaster of mix. 1:3 (1 cement : 3 fine sand). including supply of all materials T&P etc required for proper completion of the work. On ceiling and soffits of stairs upto floor two level SOR 583

Forming groove of uniform size from 12x12mm and upto 25x15mm in plastered surface as per approved pattern using wooden battens nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specification sna direction of the Engineer-in-charge. SOR-13.76

Laying of 25mm thick KOTA Stone of size 45 x 45cm and above flooring over previously prepared base with 2cm thick 1:3 cement and sand mortar including filling of joints with cement mixed with pigment required for matching the shade of floor as per direction of E/l including cutting polishing with wax polish including supply of all materials T&P etc required for proper completion of the work.NEW ITEM No. 1

Supply & fixing 6 mm (1/4") China white glazed in flooring or skirting dado laid with 1:3 cement and approved coarse sand mortar finished white cement slurry jointing and polishing complete including supply of all materials, labour and T&P etc. required fo proper completion of the work. SOR NO 628

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate. SOR NO -605

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick. DSR 11.6.1

2.5 cm (1 thick 1:2:4 plain cement concrete floor with cement, approved coarse sand and 2 cm.(3/4")graded approved stone shingle laid in panels finished with 3 mm.(1/8")floating coat of neat cement or cement and marble dust in 5:1 as specified over & including 8cm.(3") 'thick. base concrete consisting of cement ,local sand and brick ballast 4cm.(1½") gauge in the proportion of 1 :4:8 and removing any over lapping mortar at the joints of Panels if any and giving them a uniform finish including supply of all materials, labour' and T&P etc. requierd for proper completion of the work. As in item no. 601 above but without base concrete. SOR NO-601a

Providing and fixing ISi marked flush door shutters conforming to IS 2202 (Part 1) non-decorative typo, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters SOR-470ii (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

(b) Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). SOR-470ii+470iv

Mild steel or iron work of small size and sections such as holding down bolts, hold fast, tie roads, gratings etc. (when not included in an over all rates) wrought to required form, including of supply of steel, boalts nuts and wastage etc. and there fixing required for proper completion of work.SOR-502a

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws. DSR 9.20.3

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. . DSR 9.51.1 (with second class teek beding 62mm x 19mm.

Distemper two coat with oil bound distemper of approved brand manufacture and required shade on decoreted wall surfaces to give an even shade over and including a priming coat with cement primer of approved brand and manufacture such as of british, shalimar, asian paints after throughly brushing surface free from mortar droppings and other foreign matter and also including preparing the surface even also sand prepared smooth including cost of all materials. but for every coat after the first coat. (SOR No. 649 + 650)

Finishing walls with Acrylic Smooth exterior paint of required shade. New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). DSR 13.47.1

Finishing wall with water proof cement paint of approved make and quality on new wood with two coat to give an even shade including supply of all materials, labour, tools and plant etc. required for proper completion of the work. PWD - 660+661

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete. (DSR No. 14.34

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete. 250x16 mm. (SOR No. 9.6.20)

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete. 250 x 10mm (SOR 9.74.1)

200 x 10mm (SOR 9.74.2)

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete. 125 mm. DSR 9.66.1

Providing and laying "Brick Coba" 12mm thick laid with M-150 class brick bat coba 7.50 cm thick with gap of 15 mm to each other, over 20 mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with aerelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand mortar finished smooth & top mashed false square 30 cm. x 30 cm. and side wall parapet shall be mono tythic plaster wall upto 30 cm. higher and junction and corner shall be rounded by brick ballast cement and coarse sand masonary Coba with top finished plaster mixed with acetic water proofing compound @ 2% by weight & including S/o all material, labour T & P etc. complete for proper completion of work. (SOR Ch. 11 New Item)

Apply priming coat over new steel and other metal surface after and including preparing the surface throughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes ,fine steel /wood scrappers sand papering and knotting including cost of all materials, labour abd T&P etc required for proper completion of the work.Painting first coat over priming coat(but excluding cost of priming coat) on wood or steel snd other metal surface with superior synthetic enamel standard make brushing to give an even shade and finish and includjng cleaning the surface of all dirt dust and other foreign matter sand papering and stripping including cost of all materials ,labour ,T&P etc required for the proper complition of the work. (SOR 1 + 2 + 4(ii))

Apply priming coat over new wood work and on plastered surface after and including preparing the surface throughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes ,fine steel /wood scrappers sand papering and knotting including cost of all materials, labour abd T&P etc required for proper completion of the work.Painting first coat over priming coat(but excluding cost of priming coat) on wood or steel snd other metal surface with superior synthetic enamel standard make brushing to give an even shade and finish and includjng cleaning the surface of all dirt dust and other foreign matter sand papering and stripping including cost of all materials ,labour ,T&P etc required for the proper complition of the work.(iii) Superior quality but on new wood (SOR 1(b) + 2 + 4(iii))

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with. 4.0 mm thick glass panes. DSR 10.30.1

Cement concrete with 4 cm. (1½") gauge approved stone, ballast, approved coarse sand and cement in the proportion of 6:3:1 including supply of all materials, labour and T&P etc. required for proper completion of the work. As in item (279) above but in the proportion of 6: 3: 1. SOR 280

First class brick work in 1:6 cement and coarse sand mortar in super structure including supply of all materials, labour and T&P etc. required for proper completion of the work. but in super-structure, including necessary cutting and moudling of bricks as required and including honey comb brick work, thickness of wall ½ brick thick . SOR item no. 303+309+310a

12 mm thick plaster with Kankar lime over brick work minimum thickness not to be less than 3/8" (10 mm) thick including supply of all materials, labour and T&P etc. required for proper completion of the work. (with cement and fine sand of 1.25 F.M. Mortar in 1:4) SOR SI NO 584

Providing and glass strips ,joints of floor skirting dado at time of laying floors flush with floor lavel including supply of all matareial labour and T&P etc. required for proper completion of work . Same as above but 3.5 cm. Depth (SOR No. 331(b))

Providing & laying of light cinder filling under floor of toilets & other suken roofs.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. DSR 22.5

Providing & fixing of Polycarbonate sheet on truss for sky light opening

Supplying and fixing rolling shutters of approved make of 80x125 mm (3 x 3½") gauge cold rolled M.S laths inter locked throughout their entire length and joined together at the end by end locks and mounted on specially designed pipe shaft with brackets side guides and arrangement for inside and outside locking with push and pull operations complete but excluding the cost of top cover and spring. (SOR No. 520)

Providing and fixing 27.5 cm. long wire spring grade no. 2 for rolling shutters. (SOR No. 521)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) (DSR No. 5.3)

Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design. With 20x20mm square bar. DSR 19.15.1

Providing and fixing top cover for rolling shutters. 18 guage Service Block (SOR No. 522)

Providing & fixing ball bearing for rolling shutters Service Block (SOR No. 523)

Finishing walls with water proof cement paint of approved make and quality on new work with two coats to give as even shade, including supply of all materials, labour and T&P etc. required for proper completion of the work. Boundry Wall (SOR No. 660 + 661)

Providing & fixing of 75mm dia vent pipe (DSR No. 17.35.2.1) Septic Tank

Providing and fixing terminal guard : Sand cast iron S&S as per IS - 1729 (DSR No. 17.56.2.1) Septic Tank

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Circular shape 500 mm internal diameter (DSR No. 19.19.2.2) Septic Tank

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Circular shape 450 mm internal diameter (DSR No. 19.19.1.3) Septic Tank

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5 (DSR No. 19.32.1) Septic Tank

Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design. With 20x20mm square bar. DSR 19.15.1 RWH

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. M.D. -10-Circular shape 500mm internal diameter. DSR 19.19.2.2 RWH

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-incharge, upto 90 metre depth below ground level. Drilling of 300mm dia bore hole manually. DSR 23.1.1.1 RWH

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in- charge. 150 mm nominal size dia. DSR 23.4.2 RWH

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR 23.5 RWH

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR 23.6 RWH

Supplying, filling, spreading & leveling coarase sand of size range 1.5 mm to 2mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in- charge. DSR 23.7 RWH

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge. DSR 23.8 RWH

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing bymix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specificatin Clause 401. Road Work

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 4.7-405(2) Road Work

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 4.7-405(3) Road Work

Providing and laying of factory made 80 mm thick Interlocking cement concrete tiles (30mpa) including 25mm thick compacted bed of fine sand compacting and proper embedding/ laying of Interlocking tiles leveling and dressing of surface to required level and slope, filling joints with fine sand including the cost of material, labour T&P etc.required for proper completion of work as directed by Engineer-in-Charge. (SI.No. Ch. 20 New item No. 1)

Providing and applying prime coat with Bitumen emussion (ss-2) on prepared surface of granular base including cleaning of road surface and spraying primer @0.70kg per sqm using mechanical means as per techinical specification clause 502 Road Work

Providing and applying tack coat with Bitumen (VG-10) using emulsion distributor at the rate of 0.35 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 5.2-503(iii) Road Work

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of Type as per Technical Specification Clause 5.9-508. Road Work

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C as per Technical Specification Clause 5.12-510. Road Work

Construction of subgrade and earthen shoulders with approved material obtained from boeeowpits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300-2 (Carted 2.00 Km) Road Work

Providing and fixing white vitreous china pedestal type water closet (European Type WC pan) with seat and lid, 10 litre low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and Doors wherever required. W.C. pan with ISI marked white solid plastic seat and lid DSR. 17.2.1 Sanatary Fitting

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white PVc. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and taking good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid DSR. 17.1.1 Sanatary Fitting

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS: 2556, C.IL trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required: Range of two half stall urinals with 5 litre P.V.C. automatic Flushing cistern. DSR 17.5.2 Sanatary Fitting

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P brass pillar tap DSR 17.7.4 Sanatary Fitting

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing. Rectangular shape 1500x450 mm. DSR 17.32.4 Sanatary Fitting

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer- in-charge. DSR- 17.22 Sanatary Fitting

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C,1. brackets and stainless steel plug 17.10 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required. Kitchen sink with drain board. 510 x1040 mm bowl depth 225 mm. DSR 17.10.1.2 Sanatary Fitting

Providing and fixing toilet paper holder C P brass. DSR 17.34.1 Sanatary Fitting

Providing and fixing single towel Rail 600mm long stainless steel-NSR RA-4 Sanatary Fitting

provideing and fixing over head ShowerRose 180 mm dia round shape single flow (ABS BODY Crome Plated with Grey Face Plate with rowit cleaning system NSR-Ra-6 Sanatary Fitting

Providing and fixing dish holder NSR-8 Sanatary Fitting

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:24 mix (1 cement: 2 coarse sand 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. Sanatary Fitting For 100 mm dia pipe. DSR 17.37.1

For 75 mm dia pipe. DSR 17.37.2

For 150 mm dia pipe. (NSR)

Providing and fixing soil, waste and vent pipes Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 DSR 17.35.1.2 Sanatary Fitting 100 mm dia

Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 75mm dia DSR 17.35.2.2

Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside 150 mm dia IS 15905. (NSR)

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe Sanatary Fitting Providing and fixing collar 100 mm dia Sand cast iron S&S as per IS - 1729 DSR 17.57.1.1

Providing and fixing collar 75 mm dia Sand cast iron S&S as per IS - 1729 DSR 17.57.2.1

Providing and fixing collar 150 mm dia Sand cast iron S&S as per IS - 1729 NSR-RA14

Providing and fixing terminal guard. 100mm dia. Sanatary Fitting Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 DSR 17.56.1

75 mm dia Sand cast iron S&S as per IS - 3989 DSR 17.56.2.2

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. Sanatary Fitting 100 x100x100 mm. Sand cast iron S&S as per IS-1729. DSR 17.43.1.1

75 x75x75mm. Sand cast iron S&S as per IS-3989. DSR 17.43.2.2

Providing and fixing single equal plain junction of required degree Sanatary Fitting 100 x100x100 mm. Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905. DSR 17.44.1

75 x75x75mm. Sand cast iron S&S as per IS-3989. DSR 7.43.1.2. Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905. DSR 17.44.2.2

Providing and fixing plain bend of required degree. Sanatary Fitting 100 mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS: 15905 DSR 17.39.1

75 mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS: 15905. DSR 17.39.2.3

Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. Sanatary Fitting 100 mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS 15905 DSR 17.38.1

75mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS 15905 DSR 17.38.2

Providing and fixing trap of self cleansing design with crewed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors Sanatary Fitting 100 mm inlet and 100 mm outlet. Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905. DSR 17.60.1

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Sanatary Fitting Semi rigid pipe. 32 mm dia. DSR 17.28.1.1

Flaxible. 40 mm dia. DSR 17.28.2.2

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. DSR 18.7 Sanatary Fitting 15 mm nominal outer dia Pipes. DSR 18.7.1

20 mm nominal outer dia Pipes. DSR 18.7.2

25 mm nominal outer dia Pipes. DSR 18.7.3

32 mm nominal outer dia Pipes. DSR 18.7.4

40 mm nominal outer dia Pipes. DSR 18.7.5

50 mm nominal outer dia Pipes. DSR 18.7.6

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, ic fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc Sanatary Fitting 15 mm nominal outer dia Pipes. DSR 18.8.1

20 mm nominal outer dia Pipes. DSR 18.8.2

25 mm nominal outer dia Pipes. DSR 18.8.3

Making connection of GI distribution branch with G.I. main of 18.13 following sizes by providing and fixing tec, including cutting and threading the pipe etc. complete Sanatary Fitting 25 to 40 mm nominal bore. DSR 18.13.1

50 to 80 mm nominal bore. DSR 18.13.2

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) Sanatary Fitting 25 mm nominal bore. DSR 18.17.1

32 mm nominal bore. DSR 18.17.2

40mm nominal bore. DSR 18.17.3

50mm nominal bore. DSR 18.17.4

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : Sanatary Fitting 15 mm nominal bore. DSR 18.18.1

20 mm nominal bore. DSR 18.18.2

25 mm nominal bore. DSR 18.18.3

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 Sanatary Fitting 15 mm nominal bore. DSR 18.53.1

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 Sanatary Fitting 15 mm nominal bore. DSR 18.49.1

Providing and fixing uplasticised PVC connection pipe with brass unions: Sanatary Fitting 45 cm length. 15 mm nominal bore. DSR 18.21.2.1

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. Sanatary Fitting 40 mm nominal outer dia Pipes. DSR 18.9.5

50 mm nominal inner dia Pipes. DSR 18.9.6

62.50 mm nominal inner dia Pipes. DSR 18.9.7

Providing and fixing gun metal gate valve with a wheel of approvedquality (screwed end) Sanatary Fitting 40 mm nominal bore. DSR 18.17.3

50 mm nominal bore. DSR 18.17.4

65 mm nominal bore. DSR 18.17.5

Providing and fixing CI sluice valve (with cap) complete with bolus, nuts, rubber insertions at. (the tail pisces if required will be paid separately) Sanatary Fitting 100 mm diameter. Class II. DSR 18.31.1.2

Providing & Fixing 600 X 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. DSR 17.31 Plumbing Works

Providing & fixing stainless steel AISI 304 (18/8) kitchen sink with out pard as per IS 13983 with CI brackets and stainless steel plug 40 mm including painting of fittings and brackets cutting and making good the walls wherever required. 610 x 460 bowl depth 200 mm. The following items include providing, fixing and testing in position of ISI marked (IS: 1729) sand cast iron soil, waste, vent pipes and fittings cut to required lengths, fixing at wall, ceiling or on floor including connections to all required fittings complete in all respects. DSR 17.10.2.2 Plumbing Works

Providing & fixing pipes. Plumbing Works 110mm dia u.PVC Pipe. DSR 7189

Providing & fixing pipes. Plumbing Works 75mm dia u-PVC Pipe. DSR 7188

UPVC pipes (working pressure 4 kg/cm') Rubber (Seal) Ring Plumbing Works 110mm dia. DSR 7191

75mm dia. DSR 7190

UPVC pushfit coupler (single) Plumbing Works 110mm dia. DSR 7195

75mm dia. DSR 7194

10 UPVC single equal Tee (without door) Plumbing Works 110 x 110 x 110 mm. DSR 7197

75x75x75 mm. DSR 7196

11 UPVC bend 87.5 Plumbing Works 110 mm bend. DSR 7209

75 mm bend. DSR 7208

UPVC pipe clip Plumbing Works 110 mm bend. DSR 7215

75 mm bend. DSR 7213

Providing & fixing UPVC trap of self cleaning design grating with or without ventar complete, including cost of cutting & making good the walls and floors 100 mm inlet & 75 mm outlet (MR) Plumbing Works

Providing & fixing snad cast iron S&S coller. Plumbing Works 100 mm dia. DSR 17.57.1.2

75 mm dia. DSR 17.57.2.2

Providing and fxing on wall face unplasticised Rigid PVC rain water pipes Conforming to IS 13502 Tynn A including jointing with seal ring conforming 302 leaving 10 mm gap for thermal expansion - Single socketed pipes. 110 mm dia. DSR 12.41.2 Plumbing Works

Providing and fixing on wall face unplasticised - PVC moulded fittings accessories for unplasticised - Rigid PVC rain water pipes conforming to IS Type A including jointing with seal ring conforming to IS 5382 leaving 10 mm gap for thermal expansion. Bend 87.5. 110 mm bend. DSR 12.42.5.2 Plumbing Works

Providing and fixing unplasticised- PVC pipe clips al approved design to unplasticised - Rigid PVC rain water pipes by means of 50x50x50 mm hard wood plug screwed with MS screws of required length including cutting brick work and going in cement mortar 14 (1 cement 4 coarse sand) and making good the wall etc complete. 110 mm. DSR 12.43.2 Plumbing Works

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. DSR 12.44 Plumbing Works

Providing and fixing ball valve (brass) of approved quality complete. (High or low pressure with plastic floats) 15 mm nominal bore DSR 18.18.1 Plumbing Works

Providing & fixing 15 mm nominal bore 45 cm long unplasticised PVC connection pipe with brass unions. DSR 18.21.2.1 Plumbing Works

Providing and fixing 15 mm norninal bore C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. DSR 18.50.1 Plumbing Works

Providing & fixing 15 mm nominal bore C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS: 8931. DSR 18.52.1 Plumbing Works

Providing & fixing 100 mm dia C.P brass shower rose with 15 mm inlet. DSR 18.22.1 Plumbing Works

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fitting and base support for tank DSR 18.48 Plumbing Works

Providing and fiing square mouth S. W. Gully trap grade 'A' complete with C.I grating brick masonry chamber with F.P.S bricks and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4,50 kg and frame to be not less than 2.70 kg as per standard design. 150 x 100 mm size P type.DSR 19.4.2.2 Plumbing Works

Providing & fixing PTMT towel rail complete with C.P brass brackets foxed to wooden cleats with CP. brass screw 450mm. Long with total length of 495mm, width 78mm and effective height of 88mm. DSR 17.73.1 Plumbing Works

Providing & foxing is marked (IS 778) brass gate valve (class 1, PN MPa) with wheel of approved quality (screwed end) Plumbing Works 15 mm nominal bore

20 mm nominal bore

Electric works Wiring point for light with 1.5 sqmm FRLSH and 1 no 1.5 sqmm FRLSH as earth wire pvc insulated multistrand single core Cu conductor cable in pvc conduit partly laid in slab and partly concealed in wall.complete in all respect.

Wiring point for two way light with 1.5 sqmm FRLSH and 1 no 1.5 sqmm FRLSH as earth wire pvc insulated multistrand single core Cu conductor cable in pvc conduit partly laid in slab and partly concealed in wall.complete in all respect.

Wiring point for Fan/Fresh air fan with 1.5 sqmm FRLSH and 1 no 1.5 sqmm FRLSH as earth wire pvc insulated multistrand single core Cu conductor cable in pvc conduit partly laid in slab and partly concealed in wall.complete in all respect.

Wiring point for Plug /computer/TV/Aquaguard with 1.5 sqmm FRLSH and 1 no 1.5 sqmm FRLSH as earth wire pvc insulated multistrand single core Cu conductor cable in pvc conduit partly laid in slab and partly concealed in wall.complete in all respect.

S/F of LED tube light with batten suitable for upto 1X22watt LED tube light complete including tube etc.on surface.complete in all respect.

S/F of power plug with 20 Amp/250 V flush type modular switch and 5 pin 20Amp/250V socket on concealed M.S. Box.complete in all respect.

Construction of recessed distribution board with cutting of bricks and plastering with all material. size 600x480x200mm

S/F of factory fabricated MS bpx in existing sunk with Godrej type Almirah with handle etc. Size 600x480x200 mm

S/F of surface/flush mounting 4 way SPNDB with additional metal door without MCB complete in all respect. As directed at site by engineer in-charge.

S/F of surface/flush mounting 6 way TPNDB with additional metal door without MCB complete in all respect. As directed at site by engineer in-charge.

S/F of surface/flush mounting 8 way TPNDB with additional metal door without MCB complete in all respect. As directed at site by engineer in-charge.

S/F of 6 A to 32 A SPMCB(10KA) C curve.

S/F of 40 A 4 pole MCB(10KA)

S/F of 63 A 4 pole MCB(11KA)

S/F of Single Pole MCB blanking plate

Supply and wiring of Submain 2 no.4 sqmm & 1 no.2.5 sqmm earth wire FRLSH PVC insulated 1100 V grade multistrand Single core copper conductor cable in PVC conduit partly laid in slab and partly concealed in wall

Supply and wiring of Submain 4 no.10 sqmm & 2 no.6 sqmm earth wire FRLSH PVC insulated 1100 V grade multistrand Single core copper conductor cable in PVC conduit partly laid in slab and partly concealed in wall

Supply and wiring of Submain 4 no.16 sqmm & 2 no.10 sqmm earth wire FRLSH PVC insulated 1100 V grade multistrand Single core copper conductor cable in PVC conduit partly laid in slab and partly concealed in wall

S/L of 400 sqmm 3.5 core Al conductor pvc insulated armoured served sheathed cable 1100 V grade. Complete in all respect.

S/L of 16 sqmm 4 core Al conductor pvc insulated armoured served sheathed cable 1100 V grade. Complete in all respect.

S/L of 6 sqmm 2 core Al conductor pvc insulated armoured served sheathed cable 1100 V grade. Complete in all respect.

S/F of compression gland 400 sqmm 4 core

S/F of compression gland 16 sqmm 4 core

S/F of compression gland 6 sqmm 2 core

S/F of lug 400 sqmm

S/F of lug 16 sqmm

S/F of lug 6 sqmm

Supply & Errection of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN ACB(65 KA,4Pole Elect draw out , Micro Processor Release ) Switches and instrument chamber etc.complete in all respects. etc. Incoming 630 A/415 V MCCB-1 no Outgoing 100 A MCCB-05 no &63A MCCB-2nos

Providing and laying unplastisized rigid PVC Pipe Dia 150 mm confirming to IS:13592 type A including jointing,cutting and making good the walls & floor as per requirement

S/F of electronic fan regulator 120-280 V ISI marked

S and burying of 600mmx600mmx6 mm GI plate earthing

S/F of one no 8 SWG GI Wire in 15 mm dia GI pipe for earthing

S/L of 25mmx3mm GI strip for earthing. complete in all respect

S/F and making connection of ELCB of Din/RCCB rail mtg complete in all respect 25A 2 Pole

S/F of Single light wall bracket fixed on matching M.D.F.E.G. Board base etc.

S/F of Single LED Light wall bracket 3 to 6 w on matching MDFEG board base etc. complete in all respect.

S/F of recess/surface mounting round 24 W LED Down light.complete in all respect.

S/F of recess/surface mounting round 6 to 8 W LED Down light.complete in all respect.

E & T of exhaust fan

E & T of ceiling fan and regulator

S/F of Hexagonal Fan Box with hexagonal side of approx 80 mm in length fabricated from 16 SWG MS sheet in corporating 10 mm dia MS round bar duly bend for supporting fan hanger duly painted etc. Complete in all respect.

S & errection of AC 1200mm,230/250V 50Hz ceiling fan decorative type with regulator complete in all respect.

S & errection of AC 230/250V 50Hz Exhaust fan 300mm. complete in all respect.

S/F of GI pipe complete with accessories .complete

Fire fighting works Part-A Hydrant System SITC of M.S Black Pipe "C" Class (IS:1239/3589 Including Cutting, welding etc. & providing suitable flanges alongwith necessary fittings viz. bends, tees, reducers etc. & anti-corrosive treatment. 150 mm dia.

100 mm dia.

SITC of Single headed Hydrant comprising of 80 mm dia. Flanged bend 63 mm dia. SS oblique pattern landing valve complete with blank and Cap .

SITC of First aid Hose reel drum with 20 mm dia, 30 m long rubber pipe shut off nozzle, 25 mm dia., gate valve complete conforming to IS: 884/444.

SITC of RRL Hose 63 mm dia x 15 m long complete with SS coupling conforming to IS: 636.

SITC of SS Branch Pipe & Nozzle IS: 903.

SITC of Hose Box of 18 SWG M.S Sheet with glass Fronted door to accommodate 2 nos. RRL Hose & 1 nos. SS Branch Pipe with nozzel.

SITC of cast iron double flanged Non Return Valve complete with nuts, bolts and washers conforming to IS 5312. 150 mm dia.

SITC of Air Cushion Tank assembly 200 mm dia. 1.5m long with Air Release Valve pressure gauge & accessories.

SITC of GM Fire Brigade 4 Way inlet connection 63 mm dia.

SITC of sluice valve complete 100 mm dia

Terrace PVC Tank having Capacity of 5000 Liter (Rs. 10/Ltr.)

SITC of 10 HP 900 LPM capacity Terrace Pump with mimimum pressure of 2 kg including all accessories such as bend, socket, flange and other required material. Complete in all respect.

STIC of Starter Panel for Terrace Pump suitable 10 HP. Complete in all respect.

Part-B Alarm System SITC of 10 Zone Fire Alarm main control panel Microprocessor based with Public Address System. complete in all respect.

SITC of lonization Smoke Detector as per specifaction including making connections with wire.

SITC of Heat Detector ROR Type as per specification including making connection with wire.

SITC of Responsce indicator pul stanting type suitebul for including connection.

SITC of Electronic LMT Hooter, housed in MS housing suitable for wall mounting/ceiling, including making connection.

SITC of Manual Call point Break Glass type housed in MS sheet, including connection.

Supply and wiring of submain with 3 no.1.5sq mm pvc insulated 1100 volt grade single core copper conductor cable in 20 mm dia heavy gauge rigid steel conduit on surface complete in all respect.

SITC of control modules for Hooters strobes etc.

SITC of Fault Isolator

SITC of Monitor Module

S/F of Fire Extinguisher ABC type 4.0 capacity ISI marked.complete in all respect

Supply & fixing of Co2 type Fire Extinguisher 4.5 kg Capacity. Complete in all respect.