MAD/NM/15th finance fund/MT/PM/SEPT.02/2024-25

Amount

Technical Specification of Movable Toiler

TRAILER CHASIS WITH TOWING ARRANGEMENT: THE TRAILER CHASIS WILL BE MADE FROM ISMC125x65 WITH CROSS MEMBER. THE SIZE OF CHASIS WILL BE 9FT IN LENGTH & 6 FT IN WIDTH (APPROX). THE TOTAL HEIGHT OF TOILET WILL BE 10 FT(APPROX) FROM GROUND LEVEL. A TYPE FIXED DRAW BAR WILL BE PROVIDED AND SPRING LOADED EYE HOOK.PARKING STAND WILL BE PROVIDED. WHEEL & AXLE: FOUR NOS TYRE WITH TUBE OF SIZE 7.50 X 16 OF REPUTED MAKE WILL BE PROVIDED.AXLE WILL BE MADE FROM 65MM SQ BAR OF EN8 MATL. DULY ULTRASONICALLY TESTED.RIM & HUB WILL BE OF REPUTED MAKE. SEMI CIRCULAR LEAF SPRING OF 9 SECTION WITH U BOLT & OTHER ACCESSORIES FOR FITTING OF LEAF SPRING WILL BE PROVIDED.TAPER ROLLER BEARING 30209 OF SKF MAKE WILL BE PROVIDED WITH AXLE. CABIN & DOORS: CABIN & DOOR WILL BE MADE FROM STAINLESS STEEL PLATE OF GRADE AISI 304. DOOR WILL BE PROVIDED WITH S.S HANDLE & LOCKING ARRANGEMENT FROM BOTH INSIDE & OUTSIDE. CLEAN WATER TANK: CLEAN WATER TANK WILL BE PROVIDED ON ROOF TOP WITH FILLING & OVERFLOW ARRANGEMENT. OVERHEAD TANK WILL BE MADE FROM IS 2062 Gr.B EPOXY PAINTING. INSIDE FOR PREVENTION OF RUST. CAPACITY OF TANK WILL BE 1000 LTRS WITH PIPING ARRANGEMENT IN EACH CABIN.A LADDER AT THE REAR END WILL BE PROVIDED FOR EASE OF WATER FILLING AT TOP. BIO DIGESTER TANK: SLUDGE ANK WIL BE KEPT UNDER CHASIS AND WILL BE MADE FROM 1S2062GRB MATERIAL WITH EPOXY COATING INSIDE TANK: WILL HAVE PARTITIONS WITH BACTERIAL TRAP INSIDE BIO METHANE ESCAPE GAS ROUTE WILL BE PROVIDED AT THE REAR FOR THE CLEANING OF TANK VALVE WILL BE PROVIDED WITH CAMLOCK ARRANGMENT FOR SUCTION OF THE WASTE THROUGH CEASEPOOL LEVELINDICATOR WILL BE PROVIDED WITH THE TANK CAPACITY WILL BE 1000 LITERS APPROX. BACTERIA WILL BE CHARGED ON THE BIO DIGESTER TANK AT THE BACTERIAL ENCLOUSER. ROOF STRUCTURE: ROOF STRUCTURE WILL BE OFF HUT TYPE WITH SLOPES ON BOTH SIDES. THE OVERHEAD TANK TOP WILL ACT AS A ROOF STRUCTURE AND WILL BE MADE FROM IS2062GR.B MATERIAL WITH EPOXY PAINTING. TOILET ACCESSORIES: EACH TOILET CABIN WILL BE FITTED WITH COMMODE WITH SISTERN, HAND SHOWER, EXHAUST FAN, WASH BASIN, MIRRIOR, SOAP HOLDER. FLOORING: THE FLOOR OF EACH TOILET CABIN WILL BE COVERED WITH WATER PROOF PVC CLOTH WHICH CAN BE CLEANED WITH SOAP AND WATER. ENTRY TO TOILET: TWO BALCONY WILL BE PROVIDED ON EACH SIDE WITH FOLDABLE STAIR FOR ENTRY TO THE TOILET. WATER LIFTING PUMP: EACH MOBILE BIO TOILET WIL BE PROVIDED WITH WATER LIFTING PUMP OF 0.5 HP 220V- AC WITH PIPING ARRANGMENT WHICH WILL LIFT WATER FROM THE WORK SITE AND FILL THE OVERHEAD TANK WHENEVER NECESSARY. ELECTRICAL SYSTEM: MOBILETOILET WILL BE PROVIDED WITH BOTH SOLAR AS WELL AS CONVENTIONAL POWER SYSTEM OF220V-AC EACH CABIN WILL BE ILLUMINATED WITH LED LIGHT AND WILL RUN FROM BOTH SOLAR AND 220V-AC. EACH CABIN WILL BE PROVIDED WITH EXHAST FAN RUN BY 220V-AC ONLY. THE SOLAR PANEL WILL BE KEPT ON THE ROOF TOP WITH CONTROLLER AS WELL AS SOLAR BATTERY WILL BE KEPT UNDER CHASIS. BOTH PATHWAYS WILL ALSO BE ILLUMINATED BY LED LIGHT .

Technical Specification of Prime Mover

Tractor Engine Capacity (cc) 2900 CC, Type of Fuel: Diesel, Vehicle Emission Compliance: Bharat Stage TREM-IV/TERM-III, Max Engine Power (HP): 40, Engine HP (KW): 29.8-35, Cylinder: 3/4, Air Filter: Dry type, Dual element, Engine RPM at Max Power: 2100-2300, PTO: Standard PTO, Power Take Off Type: Independent, 6 Spline, RPM at Maximum PTO Power: Standard -540 @2100 ERPM, Engine Cooling System: Coolant cooled, Gear Level Position: Side Shift, Fuel Tank Capacity (Ltrs): 60-65 liter, Length of Tractor Body (mm): 3410 milli meter and above, Wheel Base (mm): 1970 milli meter and above, Size Of Front Tyre (mm): 6*16 (0.15 X0.41m), 8 PR, Size Of Rear Tyre (mm): 13.6*28 (0.34 X 0.71 m), 12PR, Tractor Transmission System: Constant Mesh Collar Shift, Number of Forward Gears/Setting: 8 Forward + 4 Reverse, Type of Wheel drive: Two Wheel Drive, Drive Axle: Rear, Type of Steering: Power Operated, Tractor Brake: Oil Immersed Disc Brake, Type of Clutch: Dry Clutch, Clutch Operation: Single, Lifting Capacity (Kg): 1600 kilogram, Warranty: 5 Years/5000 Hrs, Accessories: Hood, Hitch, Bumper, Tools. Special Features Piston Cooling Spray /Jet Pump for colling engine cylinder.Hood Lock for safety of Battery.Single Piece Hood for easy work maintenance. Top Shaft Lubrication for better Lubrication of Transmission Shaft.Rear Fitted Disel Tank for low slippage. Rate: Registration, Insurance, Tax and Number Plate.

INCLUDING ALL TAXES AND GST (SL01 & 02)

SATNAM INDUSTRIES (BID ID -5657118)

FUTURE AUTOMOBILE AGENCY PVT. LTD (BID ID -5665121)

B S TRACTORS PVT LTD (BID ID -5606853)