REPAIR TO JOINERY, ANTI TERMITE TREATMENT AND CERTAIN B/R WORKS IN NORTH SIDE OF RUNWAY AT AF STN JODHPUR

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 sqm but not exceeding 4 sqm each and removing from site complete all as specified & directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each and removing from site complete all as specified & directed by the Engineer-in-Charge.

Taking down shutters of any description exceeding 1 sqm but not exceeding 2 sqm each and removing from site complete all as specified & directed by the Engineer-in-Charge.

Taking down shutters of any description not exceeding 1 sqm each and removing from site complete all as specified & directed by the Engineer-in-Charge.

Material and labour for resecuring or easing & adjusting without taking down the shutter of any description exceeding 1 sqm but not exceeding 2 sqm each complete all as specified & directed by the Engineer-in-Charge.

Material and labour for resecuring or easing & adjusting without taking down the shutter of any description not exceeding 1 sqm each complete all as specified & directed by the Engineer-in-Charge.

Material & labour for MS Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing of Fe.290.Gde-E-165 complete all as specified & directed by the Engineer-in-Charge.

Material & labour for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wind ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe.290.Gde-E-165 complete all as specified & directed by the Engineer-in-Charge.

Material & labour for PCC 1:2:4 type B1 (using 12.5 mm graded stone aggregate) as in bed blocks etc for embedding hold fasts complete all as specified and directed by Engineer-in-Charge

Material & labour for hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engineer-in-Charge

Supply & fixing Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing complete all as specified and as directed by Engineer-in-Charge. Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

Supply & fixing Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm coloured PVC Sheet on back face, with wood free EPS and fixing in opening complete all as specified, shown in product drawing and as directed by the Engineer-in-Charge.

Supply & fixing 35 mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a), fitted to chowkats complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing Second class hard wood plain, solid, straight chowkhat and frames, wrought, framed, rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing factory made prelaminated flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels, and decorative type on both side of approved colour and pattern complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing Second class hardwood Plain fillets, square, rectangular or triangular in section, clean sawn, secured with mills or brads, sectional area exceeding 3 Sqcm and not exceeding 6 sqcm complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repairs stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repairs sheet glass 4 mm thick, ordinary quality and glazing with oil putty or wooden beads in square not exceeding 0.5 sqm in each pane complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing mild steel butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repairs mild steel butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 125mm stainless steel hasp and staple of safety type with mild steel hinge pin including bolt of hinge plate and fixed with screws complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 150 mm long stainless steel, barrel tower bolts of extruded section and fixed (ISI Marked) complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 100 mm long stainless steel, barrel tower bolts of extruded section and fixed (ISI Marked) complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 300 mm long stainless steel, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of stainless steel (ISI Marked) complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing stainless steel handles, fabricated type, anodized of size 150 mm (ISI Marked) complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 300 mm, mild steel, ordinary helical springs including roller and roller plate complete complete all as specified & directed by the Engineer-in-Charge.

Supply and fixing in repairs of 150 mm aluminium handles cast type anodised complete all as specified & directed by the Engineer-in-Charge.

Supply and fixing in repairs of 300 mm aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing factory made Box type Ventilators (primer coated), ERW Box made from 1.25 mm thick CRC sheet, & ERW hollow P sections of size 60mm X 25mm including grill using 10 Sqmm bar double riveted both gauge and glass shutter comprised gauged, glazed skelton shutters ERW section 50mm X 20mm and 1mm thick with two openable leafs consisting 2 nos sash bar of T section 20mm X 3mm complete welded to frame with one vertical mullion of ERW box type T section of size 60mm X 25mm and 1.25 mm thick including cutting holes and making good dismanteled portion with PCC 1:2:4 type B1 four numbers of each window including following fittings welded to frame shutter :- (a) MS Hold fast, 150 mm long of 12mmX3mm made to shape 04 nos per ventilator (b) MS handle of Z section 20mmX25mm, 100 mm long -01 no per leaf (c) MS tower bolt 150mm long - 02 Nos per leaf (d) Z section 20mmX25mm,100 mm long stopper -01 nos per leaf (e) Cleat 55mm long of hollow square 15mm X20mmX63mm welded to hinge -01 Nos per Leaf (f) MS Box type hinges of size 75mmX12mm- 02 Nos per leaf including stainless steel wire cloth, 0.25mm to 0.36mm nominal dia of wire and average width of aperture 1.40mm to 2mm and fixed with aluminium wire staples and glass pan 3mm thick fixed with MS pin and oil putty including two coates of synthetic enamel paint complete all as specified and directed NOTE :- During fixing of ventilator surface shall be make good in plumb with existing finishes like cement plaster, similiar wall tile, floor tile etc and as per site requirement .

Supply & fixing factory made Box Type Steel windows (primer coated), ERW Box made from 1.25 mm thick CRC sheet, & ERW hollow P sections of size 60mm X 25mm including grill using 10 Sqmm bar double riveted both gauge and glass shutter comprised gauged glazed skelton shutters ERW section 50mm X 20mm and 1mm thick with two openable leafs consisting 2 nos sash bar of T section 20mm X 3mm complete welded to frame with one vertical mullion of ERW box type T section of size 60mm X 25mm and 1.25 mm thick including cutting holes and making good dismanteled portion in PCC 1:2:4 type B1 four numbers of each window including following fittings welded to frame shutter :- (a) Hold fast, 150 mmlong of 12mmX3mm made to shape 04 nos per window (b) handle of Z section 20mmX25mm, 100 mm long -01 per leaf (c) Mild steel tower bolt 150mm long - 02 Nos per leaf (d) Z section 20mmX25mm, 100 mm long stopper -01 nos per leaf (e) Cleat 55mm long of hollow square 15mm X20mmX63mm welded to hinge -01 Nos per Leaf (f) MS pintal hinges of size 75mmX12mm- 02 Nos per leaf including stainless steel wire cloth, 0.25mm to 0.36mm nominal dia of wire and average width of aperture 1.40mm to 2mm and fixed with aluminium wire staples and glass pan 3mm thick fixed with MS pin and oil putty including two coates of synthetic enamel paint complete all as specified and directed. NOTE :- (i) During fixing of window surface shall be make good in plumb with existing finishes like cement plaster, similiar wall tile, floor tile etc and as per site requirement.

Supply & fixing Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified & directed by the Engineer-in-Charge.

Material & labour for preparation of new steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome primer of same make of paint complete all as specified & directed by the Engineer-in-Charge.

Material & labour for preparation of new wooden surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint one coat of wood primer of same make of paint complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing of 150 mm floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 40 mm dia cupboard knobs fixed with nut screw and washer of mild steel bright bolt complete all as specified & directed by the Engineer-in-Charge.

Material & labour for welding in repairs not exceeding 2.5 cm in length, thickness of metal to be welded not exceeding 6 mm complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing Aluminium Anodized powder coated (Thickness of powder coating not less than 50 micron) aluminium frame for doors , windows, ventilators, partition wall with one or more rebates including joining cleat for fixing etc complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing anodised aluminium door shutters, powder coated (Thickness or powder coating not less than 50 micron), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc.complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing anodised aluminium, powder coated of any colour (Thickness of powder coating not less than 50 micron), window and ventilator shutter side hung type without sashbar, aluminium sections weighing 0.55kg/m incl necessary joining cleat glazing clips, rubber neoprene packing, alumimium anodised snap beading, screws , peg stay 150mm long -1 No, hinges type B-21 100mm long -2 Nos, suitable handle -1 No complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing sheet glass 5.0 mm thick, ordinary quality and glazing with oil putty or wooden beads in square exceeding 0.5 sqm in each pane complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 5.0 mm thick froasted glass panes and glazing with oil putty or fix in aluminium door / widnow complete all as specified & directed by the Engineer-in-Charge.

Material & labour for repairs to Aluminium doors exceeding 1.50 Sqm but not exceeding 5.00 Sqm by replacement of necessary joining cleat, glazing clips, rubber neoprene packing handles 2 Nos in each doors, hinges anodised aluminium snap beading screw etc including chowkhat and refix in the same opening after complete repair except glass complete all as specified & directed by the Engineer-in-Charge.

Material & labour for repairs to aluminium doors not exceeding 1.50 sqm by necessary replacement of joining cleat, glazing clips, rubber neoprene packing handles 2 Nos in each doors, hinges anodised aluminium snap beading scrw etc and refix in the same opening after complete repair except glass complete all as specified & directed by the Engineer-in-Charge.

Supply and fixing in repairs Aluminium (extruded) body Door closer hydraulically regulated, designation No 1, universal type, suitable for door shutters upto 700 mm in width & of weight not more than 35 kg complete all as specified and as directed by Engr-in-Charge .

Dismantling of boarding any description fixed in any position with nails complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 18 mm solid PVC ply of 1st quality of approved colour, fixed with screw and solvent cement/adhessive complete all as specified and directed by Engineer-in-charge.

Supply & fixing 18 mm solid PVC ply of 1st quality of both side white colour, fixed with screw, solvent cement/adhessive complete all as specified and directed by Engineer-in-charge.

Supply & fixing 12 mm solid PVC ply of 1st quality of both side white colour, fixed with screw, solvent cement/adhessive complete all as specified and directed by Engineer-in-charge.

Supply & fixing Continuous (piano) hinges, stainless steel, bright finish or electrogalvanised, Width of flaps (when open) not less than 30mm, complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repairs 8 mm thick sheet glass shelf assembly with Stainless steel backets as approved of size not exceeding 0.25 Sqm complete all as specified and directed by Engineer-in-charge.

Supply & fixing four lever brass Locks for cupboard/Glass doors, grade I, size 50mm complete all as specified and directed by Engineer-in-charge.

Supply & fixing magnetic catcher for Wardrobe, Cub-boards Etc complete all as specified and directed by Engineer-in-charge.

Supply & fixing sliding channels for holding glasses in wardrobes complete all as specified and directed by Engineer-in-charge.

Supply & fixing stainless steel Pivot hinge of size not exceeding 75 mm for glass doors complete all as specified and directed by Engineer-in-charge.

Supply & fixing in repairs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified & directed by the Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for and removing from site complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing rolled mild steel work Fe-410-W (Gde-E-250) quality -A in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified & directed by the Engineer-in-Charge.

Dismantling of old unserviceable, rusted, broken (corrugated/semi corrugated, etc.) roofing sheets any type in ridge and roof coverings complete all as specified & directed.

Supply & fixing Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing Pre-painted galvalume aluminum zinc coating GI based plane steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing Mild steel, plain black sheet 0.8 mm thick in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; waters tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified & directed by the Engineer-in-Charge.

Demolition of cement concrete (Unreinforced) in ground floor & paving not exceeding 15 cm thick (below or above ground level) complete all as specified & directed by the Engineer-in-Charge.

Material & labour for 100 mm thick,PCC 1:4:8, type D-2, (using 40 mm graded crushed stone aggregate), as in sub base or flooring complete all as specified & directed by the Engineer-in-Charge.

Material & labour for 10 to 12 mm thick vitrified unglazed and unpolished, scratch resistant, matt finished coloured tiles (square/rectangular) of size not less than 300mm x 300mm as in parking /hardstanding etc including set, jointed in cement slurry and pointed in white or coloured cement to match the colour/ shades of tiles over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified & directed by the Engineer-in-Charge.

Material & labour for Cement concrete Type B-2, 1:2:4 (using 40 mm graded stone aggregate) in foundations, filling and mass-concrete complete all as specified and as directed by Engr-in-Charge .

Material and labour for providing post construction Anti termite treatment and injecting along the external wall in plinth protection using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed by Engr-in-Charge .

Material and labour for providing post construction Anti termite treatment at points of contact of wood work by chemical emulsion @ .5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and as directed by Engr-in-Charge .

Material and labour for providing post construction Anti termite treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as specified and as directed by Engr-in-Charge .

Material & labour for Venetian blinds, vertical type, 100 mm wide with polyster fabric of approved colour and pattern with aluminium fittings, and top rail and nylon buttons / loops etc fixed cuttings and alteration if necessary whereever AC/ coolers exists including dismantling old unserviciale venetian blinds complete all as specified and as directed by Engr-in-Charge .

Supply and fixing in repairs 7mm thick aluminium grill of make ' Deco grill DG-104 model fitted in to suitable aluminium channel and fixed to windows / ventilators including channel complete all as specified and as directed by Engr-in-Charge .

Supply and fixing in repairs stainless steel curtain rod of dia 20-25 mm complete all as specified and as directed by Engr-in-Charge .

Supply and fixing Stainless steel bracket for holding curtain rods and curtain rod end finials of dia 20-25 mm as approved complete all as specified and as directed by Engr-in-Charge .

Supply and fixing in repairs brass mortice lock vertical type of size 100 mm complete all as specified and as directed by Engr-in-Charge .

MAA CHAMUNDA CONSTRUCTION & SUPPLIER

DEV INDUSTRIES

VIKAS CONSTRUCTION CO.

Om Trading Corporation