Construction of Library-cum-Reading Room at Ganderbal.

Structural Estimate

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil :

P/L, of dry stone soling duly hand packed for foundation and backfilling with ramming, dressing, and compacting all inclusive leads, lifts, loading, un-loading, cost and carriage of material involved complete.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) complete.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete

Boring, providing and installing bored cast-in-situ reinforced cement concrete pile of M30 grade concrete mix, diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embeded in the pile cap etc. all complete including removal of excavated earth with all lifts and leads(Length of pile for payment Shall be measured from top of shoe to the bottom of pile cap) By percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, 450 mm dia piles

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/ Anchor pile method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer-in Charge. Initial test (Test Load 2.5 times the safe capacity)

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/ Anchor pile method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer-in Charge. Routine test (Test Load 1.5 times the safe capacity)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-incharge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately. All works upto plinth level complete.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-incharge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately. All works above plinth level upto floor V level complete.

Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

Centering and shuttering including strutting, propping etc. and removal of form work for:Columns, pillars, piers, abutments, posts and struts.

Centering and shuttering including strutting, propping etc. and removal of form work for:Suspended floors, roofs, landings, balconies and access platforms, Shelves (cast-in-situ) all complete.

Centering and shuttering including strutting, propping etc. and removal of form work for:S Lintel, beams, plinth beams, girders, bressumers and cantilevers all complete.

Centering and shuttering including strutting, propping etc. and removal of form work for:Edges of slabs and breaks in floors and walls Under 20 cm wide all complete.

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete. all complete.

Filling available excavated earth including royalty (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. all complete.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.Welded

Providing and fixing of Bolts incl. all necessary nuts, washers all complete Job (Anchor Bolts).

Architectural Estimate

Providing and laying autoclaved aerated cement blocks masonry with150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge.(The payment of RCC band and reinforcement shall be made for separately).

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : 1:6 ( 1 cement : 6 coarse sand) including Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level.

Half brick masonry wih common burnt class (non Modular) bricks of class designation 7.5 in foundations and plinth inculding curing in: Cement mortar 1:4 ( 1 cement : 4 coarse sand) and Extra for half Brick masonry in superstructure above plinth level upto floor V level and Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry all complete.

15mm Cement plaster on the rough side of single or half brick wall of mix:1 : 6 ( 1 cement : 6 fine sand) all complete.

12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 coarse sand) all complete.

Providing 10cm/7.0cm thick and 5cm/5.7cm projected string course with bricks of class designation 7.5 in cement mortar 1:4 (1 cement: 4 coarse sand) and curing complete.

Extra for plastering done on moulding cornices or architraves including neat finish to line and level : In two coats all complete.

Providing and applying ornamental moulding in cementing plaster vertical post with mix of 1 cement and 1 fine sand(1:1 mix) including material scaffolding shuttering etc complate job as per architectural drawing and approved by consultant/client.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position incl. SS expansion fasteners for bricks/concrete work incl. cost of material incl. all leads, lifts, carriage etc upto site of work complete wood as per the directions of consultant/ as per the drawings enclosed: Second class kail wood

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws 35mm thick complete.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class Kail wood 35mm thick .

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : 35mm thick Second class Kail wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) all complete.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick 4 mm thick glass pane (weighing not less than 10 kg/sqm) .

Providing and fixing of hardware fittings of approved brand and manufacture of required type type as approved by EIC as per specifications (Brass Heavy duty) all complete. Modular door lock SS finish Handle 10" with dual locking system inside & Outside (Godrej) heavy Duty.

L-Drop

Tower Bolts 100mm (Window)

Handle 100mm (window)

I-Hooks 150mm

Tower Bolts 150mm (Doors)

Handle 125mm (Doors)

Butt Hinges of 100x63x3.2mm

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work .

Applying priming coat:With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm complete.

Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) all complete.

Kota stone slab 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average) thick cement mortar 1:3 (1 cement:3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing, polishing and curing complete.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.In all colours, shades, except White, Ivory, Fume Red Brown.

Providing and fixing Ist quality ceramic glazed wall tiles of approved make, in all colours, shades(of 7-8 mm thick of different sizes) as approved by Engineer- in-Charge, in walls, skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade incl. all carriages etc complete.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm . This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry all complete..

Providing and fixing of KHATAM BANDI ceiling of first class budloo/fir wood excluding the cost of frame work which is to be paid separately.Chaar Gul

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in-charge (Frame work shall be paid for separately). 12mm thick commercial ply conforming to S : 1328 BWR type all complete.

Providing, fixing and applying Plaster of Paris (POP) false ceiling consisting of frame work made with 50mm sq M.S. tubes of 18 G thickness as main runner at 600 mm c/c both ways, suspended/ supported with M.S. flats 25x4 mm from existing R.C.C. slab, finished smooth to line and level including necessary supports, scaffolding etc. as required and also including applying a coat of red oxide zinc chromate primer over the M.S. frame work and suspenders complete. Including providing and fixing expanded metal of size 5.25 mm x 1.25 mm thickness welded to main runners and applying POP (calcium sulphate semi hydrate variety) to the expanded metal of thickness not less than 10 mm

French spirit polishing, Two or more coats on new works including a coat of wood filler complete.

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.2 mm thick complete.

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work all complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mmnominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete

Providing and fixing plained eaves boarding of size 300x40 mm (nominal size) second class kail wood fixed with necessary screws, incl. all necessary fittings/fixtures etc complete.

Providing and fixing 20mm thick wooden planks ceiling (frame work for base to be paid for separately) with M.S. screws 2nd class kail wood all complete.

Providing/Fixing of CGI Colour coated (Hi-Rib) profile sheets for roofing including vertical/curved surface fixed with Polymer coated J or l hooks, bolts and nuts 8mm diameter with bitumen and G.I Limpet washers or with G.I Limpet washers filled with white lead, including overlapping of sheets complete (upto any pitch in horizantal/ vertical or curved surface) excluding the cost of purlins, rafters (0.50mm thick) etc incl ridges hips/ valleys 60cm vide of colour GI sheets sheets including cost of screws/ washers all complete and cost and carraiges of materials complete.

Providing and fixing thermal insulation of ceiling (under deck insulation) with specified glass wool conforming to IS: 8183, 50mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3mm) @ 60cm c/c and wire mesh of 12.5mm x 24g wire for top most ceiling of building. With resin bonded rock wool with density 48 kg/cum all complete.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : Budloo / Fir wood

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm all complete.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing of 50mm dia Coated steel hand rails installed horizontally in walls including cutting, welding, granding to required shape and size by required dash fastners, nuts, bolts, screws etc all complete job Grade 304 pattern and design as per approved by EIC.

Providing and fixing of stainless steel nevel post (Ornamental) incl. top ballof AISI 304 grade of required height duly anchored to floor with dash fasteners. Height of the nevel post shall not be less than 1050mm above the finished skirting level all complete as per architectural complete.

Providing and Fixing of Aluminum work for doors, windows, ventilators and partitions incl glazing with glass panes of 5mm thickness and 12 mm thick decorative pre-laminated particle/MDF boardboth side laminated w'th extruded build up tubular sections/appropriate Z sections and other sections of approved make conforming to IS 733 and IS 1285, fixed with rawiplugs and crews indl necessary filling up of gaps at junctions, at tops, bottoms and sides with required PVC/Neoprene felt etc. all complete as per directions Of Engineer 1/C for fixed portion,' Electro coated aluminum, complete as per approved drawings and sample to be approved by the Engineer-in-charge

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Carriage of Material:- Sand/Stone agg. For an avg. lead of 10 Kms

Carriage of Bicks avg. lead of 40 Kms.

(Internal Electrification)

Wiring for Light point/Exhaust point with (P+N+E) 3x1.5 sq.mm FRLS-H/HFFR PVC insulated Multi strand Copper conductor single core cable (Polycab / Finolex / Anchor/ Salzer/ Havells Make) in existing surface/recessed Conduits (Including Cost of Conduit) laid in slabs with 01 No.of 6 Amp Modular Switch,Modular Plate,Cover in front & suitable GI box etc ISO/IEC Certified Anti-Bacterial Series ofHavells(Crab Tree)/ Legrand/ L&T/ Siemens/ ABB/ Equivalent Make & shall be approved before execution of work.

Supplying and Fixing of Indicator as required, ISO/IEC Certified Anti-Bacterial Series ofHavells(Crab-Tree)/Legrand/L&T/Siemens/ABB/Equivalent Make & shall be approved before execution of work.

Wiring for Fan point with (P+N+E) 3x1.5 sq.mm FRLS-H/HFFR PVC insulated Multi strand Copper conductor single core cable (Polycab/Finolex/Salzer/Anchor/Havells Make) in existing surface/recessed Conduits (Including Cost of Conduit) laid in slabs with 01 No.of 6 Amp Modular Switch,Modular Plate,Cover in front & suitable GI box etc ISO/IEC Certified Anti-Bacterial Series of Havells(Crab-Tree)/Legrand/L&T/Siemens/ABB/Equivalent Make & shall be approved before execution of work.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required,ISO/IEC Certified Anti-Bacterial Series ofHavells(Crab Tree)/ Legrand/ L&T/ Siemens/ ABB/ Equivalent Make & shall be approved before execution of work.

Wiring for Power Plug with (P+N+E) 3 x 4 sq.mm FRLS-H/HFFR PVC Insulated Multi strand Copper Conductor single core cable in surface/Recessed Conduit (Polycab/Finolex/Anchor/Salzer/Havells Make)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required, ISO/IEC Certified Anti-Bacterial Series ofHavells(Crab-Tree)/Legrand/L&T/Siemens/ABB/Equivalent Make & shall be approved before execution of work.(Including Inverter Input/Output)

Wiring for 6Amp Plug(Computer Point) with (P+N+E) 3 x 2.5 sq.mm FRLS-H/HFFR PVC Insulated Multi strand Copper Conductor single core cable in surface/Recessed Conduit (Polycab/Finolex/Salzer/Paraflex Make)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including proving and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings), ISO/IEC Certified Anti-Bacterial Series ofHavells(Crab-Tree)/ Legrand/ L&T/ Siemens/ ABB/ Equivalent Make & shall be approved before execution of work.

Wiring for Sub main Wiring along with earth Wire with the following Sizes of FRLS-H/HFFR PVC insulated copper conductor, single core Cable in surface/Recessed medium class PVC conduit (Polycab/Anchor/Finolex/Salzer/Havells Make) & shall be approved before execution of work.

2x10 sq.mm+ 1x6 sq.mm (P+N+E) for Power point Sub main in One run from Main Panel to Distribution Boards.

2x6 sq.mm+ 1x6 sq.mm (P+N+E) for Lighting/Inverter/AC Point Sub main in One run from Main Panel to Distribution Boards.

2x2.5 sq.mm+ 1x2.5 sq.mm (P+N+E) for Lighting/Inverter Circuit in One run from switch boards to Distribution Boards.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required of Havells(Crab-Tree)/ Legrand(Myris)/Anchor Rooma Plus/ Schneider(Zencelo)/ABB/Equivalent Make

Supply/Fixing/Testing and Commissioning of 6Amp to 32Amp Rating SP,240v,*C* Curve 10K, Miniature Circuit Breaker suitable for inductive load of following poles in existing MCB . DB Complete with connections.(L&T/Siemens/Legrand/ABB /Schneider/BCH Make)

Supply/Fixing/Testing and Commissioning of Supplying and fixing following rating, double pole,(single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. (L&T/Siemens /Legrand/ABB/Schneider/BCH Make)

Supplying and Fixing of 8-Way single pole & neutral (SPN), sheet steel, Double Door Distribution Board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc, as required. (L&T/Siemens/Legrand/ ABB /Schneider/BCH Make)

Supplying and Fixing of MCB 8-Way (4+24) horizontal typed , sheet steel, Double Door Distribution Board, TPN 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc, as required. (L&T/Siemens/Legrand/ ABB /Schneider/BCH Make)

ENVIRONMENTALLY SAFE MAINTENANCE FREE COPPER ROD EARTHING SYSTEM Necessary soil treatment is to be made by the contractor in order to improve the Pit resistance Value.Supply,Installation and Testing of 75 mm copper Pipe Filled with Crystalline conductive Mixture with Eco friendly GEM Backfill Compound 2No. Bags also having Earth pit chamber (300mm x 300mm) with man- hole cover for the above. Including cost of 20mm Wide copper strip as required in one run fitted with of brass nut bolt & spring washer from EARTHING ROD up to MAIN Control PANEL through suitable DWC High Density Poly ethylene Pipe having Corrugation complete job.

Supply and fixing of 18 Watt LED Powder coated die cast/Extruded aluminum Body including trim with Aluminum Reflector(System lumen efficacy ≥ 120 lm/Watt ) Recess/surface mounted (Commercial type) downlighter having following specficafications .The luminaire should have a colour temperature of 6500°K, CRI≥80 and SDCM≤5. Luminaire shall be designed to emit initial system lumen output of greater than 2150 lumens .The downlighter shall be back-lit & not side-lit. The driver shall have THD≤10% (@full Load) and PF ≥ 0.95 (@full load). The luminaire housing /body should made of pressure die-cast aluminum. The fixture should comply with the parameters as per IS10322. The luminaire shall have impact resistance of IK02 & ingress protection of IP20. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The luminary shall have average life of 50000 hrs operating temperature -10 C to + 45 C The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab & BIS certificate for LED Luminaire & Driver. The Agency / firm must submit the Technical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty from OEM for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out what so ever reason.Approved Make: Signify (Philips)/LightingTechonology/Endo/Regent /Trilux /Wipro/Equivalent make.

Supplying, installation, Testing & Commissioning of Panel light 1x2 ft of 22-24 Watt(System lumen efficacy ≥120 lm/Watt) of Powder coated Extruded aluminium/CRCA Body and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6000°K / 6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.) Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS,PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 3 year OEM warranty. LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C).The Agency / firm must submit the Technical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. Approved Make: Signify (Philips)/Lighting Techonology/Endo/Regent /Trilux /Wipro/Equivalent make.

Supplying, installation, Testing & Commissioning of Panel light 2x2 ft of 34-36 Watt(System lumen efficacy ≥120 lm/Watt) of Powder coated Extruded aluminium/CRCA Body and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6000°K / 6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.) Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS,PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 3 year OEM warranty. LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C).The Agency / firm must submit the Technical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. Approved Make: Signify (Philips)/Lighting Techonology/Endo/Regent /Trilux /Wipro/Equivalent make.

Supplying, installation, Testing & Commissioning of 100 Watt (System lumen efficacy ≥120 lm/Watt) Flood Light, powder coated pressure die cast aluminum body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, freq 50/60 hz, Operating temp range -15 deg to 50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2 , P. F.≥0.95, IP-66,IK-10, CRI >80 , under voltage and over voltage protection, EMIEMC as per CISPR -15 , lenses for beam angle 30 deg-120deg as per the application and the project requirement deg., suitable tilt able fitting, life time (LED,Driver & electrical circuitary) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 lm/Wattoutput . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). The Agency / firm must submit the Technical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty from OEM for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out what so ever reason. Approved Make: Signify (Philips)/Crompton/Lighting Techonology/Surya/Wipro make.

Supply/Installation/Testing and Commissioning of BLDC 1200 mm sweep, ceiling fan with 03 No. blades, 30 cm long down rod, 02 No. canopies, shackle kit, Power Factor not less than 0.9, Service Value including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase Supply, etc. complete as required. USHA/Halonix/Polycab/Orient Make.(5-Star)

Supply/Installation/Testing and Commissioning of upto 400mm Shutter Typed,320 Cu.m/Hr.AC 220-240 Volts, 50 Hz Exhaust fan made out of ABS Plastic Material with inbuilt thermo cut-off Protection and Noise Level not exceeding 37dB o including connection etc USHA/Anchor/Polycab/Orient/Halonix Make.

Supply/Installation/Testing and Commissioning of ABC type Fire Extinguisher 4.Kg. Capacity ISI Mark(IS:15683) and dully certified.

Supply/Installation/Testing and Commissioning of CO2 Type Fire Extinguisher 4.5 Kg. Capacity ISI Mark(IS:15683) suitable for 'B' and 'C' class fires - inflammable liquids, gaseous fires like L.P.G,acetylene and electrical fires.

Supply and Fixing of single pole blanking plates on existing MCB boxes, excluding cost of Boxes.

Providing and fixing of bakelite hylam sheets of required size including cutting, filing with S/F screws etc.

Supply and Fixing of Modular 25-32Amp industrial Socket outlet having fitted with 25-32 Amps DP MCB and Top with Modular Plate,Cover in front & suitable GI box etc for AC Points of Legrand/Anchor/Seimens/L&T/ Equivalent Make.

Supply/Installation/Testing and Commissioning of 9-15 Watt. LED Mirror Light (decorative type) fitting with Aluminium Body of Philips/Bajaj/ Wipro/Jaguar/Panasonic/Havells/Equivalent Make including making of necessary connections including cost of Ceiling Rose,Silken wire also with round plates etc complete.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required of Legrand/Panasonic/Anchor/Schneider/Equivalent Make

Supply/Installation/Testing/Commissioning of 2-3KVA/24 V Pure Sinewave Solar Inverter With ISOT Technology, Intelligent Load Sharing & BIS Certified (with 2-Year Warranty), 02 No. of 200Ah,12V Tubular battery (with 36 Months Warranty) & Suitable Trolley Support for Inverter resting & resting of Tubular Battery etc Luminious/EXIDE/AMRON Make.(For Each Floor) & CCTV Control Room.

Supply/installation/testing and commissioning of CPRI-approved (IS/IEC:61439) panel Wall/floor-mounted compartmentalized, 415 volts TPN MCCB Main Distribution panels, fabricated out of sheet steel of 16 gauge dust-protected, painted incl earth terminal with all necessary accessories as required for panel with internal wiring of panel. The Panel is to be provided and fitted with the following adjustable-type controlling/protection switchgear devices: ​1. Normal Incoming: ​200 Amp TPN MCCB with breaking capacity of 36 KA with extended thimbles of Legrand/Siemens/ABB//LK make = 1 No.,400 Amp Bus bar Al Strips(3+1) = 1 Set, MultiFunctional Meter =1 No., phase indicators =1 set 2. Generator Incomer: 100 Amp Four Pole Change over Switch of Legrand/Siemens/ABB//LK make = 1 No., 200 Amp Bus bar Al Strips(3+1) = 1 Set, Digital Voltmeter =1 No., Digital Ammeter = 1 No., CT coils for Ammeter 300 / 5A = 1 set, phase indicators =1 set ​3. Bypass Switch: 100 Amp 4-Pole Bypass Switch for bypassing 25 KVA AVR ​Outgoing: ​(1) 63 Amp DP MCB (10 KA) of Legrand/Siemens/ ABB/Schinder /L&T make = 06 No for normal heating sub main ​(2) 40 Amp DP MCB (10 KA) of Legrand/Siemens/ ABB/Schinder /L&T make = 12 No for Sub main lighting/ACs ​(3) 32 Amp DP MCB (10 KA) of Legrand/Siemens/ ABB/Schinder /L&T make = 03 No for Sub main invertor The Panel manufacturing unit should be CPRI Registered and the Contractor has to submit the test certificate of main switch gear and Drawing of panel (Showing claerly dimensions of panel with spacing of switchgear as per IE Standards) is to be approved by Engineer Incharge before manufacturing.

Supply/Installation/Testing & Commissioning of 3-phase 25 KVA,50 Hz Oil cooled unbalanced type Voltage Stabilizer SERVO control of Approved brand COPPER wound of AE/Chinar/Cosco Make ISI/1SO/IEC certified for smooth functioning/constant voltage supply having Technical Specifications : Input voltage(Ph-N) ranging from 120 Volts to 240 Volts and a balanced output Voltage of 230 Volts, ±2% Buck Boost Transformer Copper wound 99.9% ,OIL Immersed COOLING OIL, High cut/Low Cut /Time delay/Over Cut through Micro Controller and Spike Protection.(For Lighting & Machine Points Only)

Providing and Laying of shock proof rubber mats of 2mx1mx12mm thick in size of Standard Make.

Supply/Laying/Testing and Commissioning of 3.5- Core 95 mm sq. Al armored XLPE Insulated,PVC cable Havells/Polycab/RR Kabel/Paramount/KEI Make. Including Supply/Laying of HDPE Pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation where required and refilling the trench of standard make as approved.The cable shall include end termination lugs with its crimping /taping.

(CCTV-Network)

Supply/Installation/Testing/Commissioning of 5MP IP Network TDN Low-Light IR Fixed Lens Dome Camera, 1/2.7" CMOS or better, 5MP (2880 x 1620)@ 25fps or better, triple stream at various resolution & Frame Rates, Min.Illumination required 0.007 lux (color), 0 Lux IR On, 2 IR LEDs, Smart IR with upto 30m IR distance, Auto ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio 50db, Shutter Speed 1/2-1/100000S,Adavance Video Compression technology such as H.265, H.264 & MJPEG, Fixed Lens 2.8mm, Field of View FoV H:90°, V:50°, BLC, HLC, WDR, 3DNR, White Balance - Auto/Manual, Minimum Edge Intelligence Video Analytics, 4 Privacy Mask, 8 Region Of Intreset, Defog, HTTPS, IP Filter, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption, 2-Way Audio Full Duplex Line IN/Out, 256GB SD card support, Alarm: 11n/1out, PoE (802.3 af) and 12V DC, Max 5W, IP 66/67 & IK10 with Die Cast Aluminium Housing, Having Operating temp range: -40°C to 60° C. Certifications: ONVIF Profile S/G/T Compliant, CE, FCC, EN, RoHS & NDAA Section 889 compliant having STQC of Matrix/Equivalent Make & sample needs to be approved from department. Including cost of Camera PVC Boxes.

Supply/Installation/Testing/Commissioning of 5MP IP Network TDN Low-Light IR Fixed Lens Bullet Camera, 1/2.7" CMOS or better, 5MP (2880 x 1620)@ 25fps or better, triple stream at various resolution & Frame Rates, Min.Illumination required 0.007 lux (color), 0 Lux IR On, 2 IR LEDs, Smart IR with upto 30m IR distance, Auto ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio 50db, Shutter Speed 1/2-1/100000S,Adavance Video Compression technology such as H.265, H.264 & MJPEG, Fixed Lens 2.8mm, Field of View FoV H:90°, V:50°, BLC, HLC, WDR, 3DNR, White Balance - Auto/Manual, Minimum Edge Intelligence Video Analytics, 4 Privacy Mask, 8 Region Of Intreset, Defog, HTTPS, IP Filter, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption, 2-Way Audio Full Duplex Line IN/Out, 256GB SD card support, Alarm: 11n/1out, PoE (802.3 af) and 12V DC, Max 5W, IP 66/67 & IK10 with Die Cast Aluminium Housing, Having Operating temp range: -40°C to 60° C. Certifications: ONVIF Profile S/G/T Compliant, CE, FCC, EN, RoHS & NDAA Section 889 compliant having STQC ofPelco/Matrix/Honeywell Make & sample needs to be approved from department. Including cost of Camera PVC Boxes.

Supply, Installation, Testing & Commissioning of 32 Channel NVR with 4K Support and 2 HDD Slot. 32 IP Channel Inputs; HDMI. 12MP, 8MP, 5MP, 4MP, 3MP, 2MP, 720p, D1 and CIF Recording Resolution .2x 4K/8x 1080p/16x 720p/ 36x D1 @ 30FPS Local Decoding. 2 SATA HDD Support (Maximum 18TB Capacity Support). Save Storage Space with Adaptive Recording and Camera-wise Recording Retention. SMS & Email Notification, Video Pop-up and Alarms. Throughput- 1024 Mbps - 512Mbps Uplink, 512Mbps Downlink, ONVIF and Major Camera Brands Support. NAS Support: 2 NAS (CIFS, NFS). Mobile Viewer Application Should Support Calling from Mobile App Feature Where a Mobile Number Can be Added Per Camera in the Device and The User Can Directly Call a Concerned Person by Just One Click on Camera View from Mobile(without any SIM card in NVR). The device should be capable of acting as a Master device and should be able to Add,View,Playback and Configure at least 18 other connected slave devices (NVRs) camera's from the Local View via HDMI, without need of any Server/workstation. BIS, FCC of Matrix/Equivalent Make.

Supply, installation, testing and commissioning of 10TB Survillance HDD of WD/Seagate/Toshiba/ Consistent/Equivalent Make & Shall be approved not less than SDO.

Supply/Installation/Testing & Commissioning of high quality smart UN-managed 16 Port PoE with 2 uplink port, power adaptor included. D-link/Cisco/Alcatel/Netgear/ Juniper/WD Make sample needs to be approved from department.

Supply/Laying/Testing & Commissioning of UTP CAT 6 23 AWG solid ETL/ ROHS certified. , shielded, outdoor type cable with 25mm dia conduit Pipe of reputed Make: Dlink/Cisco/Equivalent Make.(For CCTV+Networking)

Supply & Installation of IP-20 & IK-08, UL Listed Wall mounted Double Section Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, Vertical Mounting Rail 1.6 MM with 'U'Marking, with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19" angles with wall mounting provision on wall. Accessories like: 1 No of 19" 1U Horizontal Cable manager, 1 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware, 1 No of 19" 1U, mountable socket strips with 5 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with Suitable Anchor fastner etc as required.All as per pre approved by Engineer in charge For additional technical parameters of products/ work, refer Annexure "A" attached with this BSRof D-Link or Equivalent Make Including Supply of power extension cord etc:- 9 U Rack with Width 600 mm & Depth 400 mm + 100 mm

Supply/Installlation/Testing & Commissioning of LED TV of Samsung/Sony/L.G Make & Shall be approved not less than SDO, Display Size: Shall not be less than 43 inches, Brightness: Minimum 300 Nits or Better, Contrast Ratio Static: 1200:1 or better, Video Processing: The display shall integrate a multi-core AI-assisted 4K engine capable of real-time content up-conversion, dynamic tone mapping, and support HDR10 / HLG,HDR & Dynamic Mapping: Shall support high dynamic luminance rendering with bit-depth interpolation up to 10-bit HEVC decoding at 60 fps, enabling precise gradation control under variable lighting, Audio System : Dual down-firing transducers (10 W × 2), AI-based equalization, and support multi-channel Dolby Atmos, Acoustic: Intelligence Shall support responsive acoustic calibration, automatic volume normalization, and adaptive sound field correction for spatial uniformity, Broadcast Compatibility: Embedded multi-standard tuner section shall accommodate DVB-T/T2, DVB-C, DVB-S/S2, and analog PAL, Connectivity Interface: 3 or more HDMI, USB (v2.0/v3.0), SPDIF optical digital output, dual RF ports, and RJ-45 Gigabit Ethernet , dual-band Wi-Fi and Bluetooth 5.0 or higher, Smart OS Environment: The display shall operate on a secured embedded OS (OEM owned) supporting sandboxed application containers, OTT access, and cloud-service integration without external compute dependency. Shall include an AI recommendation and inference module facilitating contextual content suggestions, voice recognition, intelligent assistant interoperation, and adaptive interface customization, Voice & Assistant Integration: The display shall support voice interface engines compatible with leading ecosystems (such as smart home or hub platforms), Remote Features: Motion sensor based air mouse pointer for cursor control on the screen, making navigation intuitive, move pointer by waving the remote, scroll wheel allows fast navigation on screen, built-in voice command support for hands free operation, remote should be bluetooth connectivity with display, Smartcasting & Device Sync: Wireless screen casting from (Windows, Android, iOS, macOS) using standardized casting protocols Google Cast, Airplay, OTT & Channel: Display shall provide access to major over-the-top streaming ecosystems and more than 100 IP-based infotainment channels, operable without auxiliary media boxes and subscription, Safety Features: USB Cloning, IP Control, App Blocking, Input Locking, Power Consumption: 165W Typ. Or better.

(Networking)

Supply, Installation, Testing & Commissionig of 24-Port Managed Networking switches of Cisco / Juniper / D-Link make Incl making of necessary connections by networking computer Engineer having following specifications Model :- 10BASE-T/100BASE-TX/1000BASE-T: 24 4 100/1000 Mbps GbE/SFP combo ports Performance : :Switching Capacity: 56Gbps :Min. Packet Forwarding Rate: 41.7 Mpps :MAC Address Table: 8K and 4.1 Mbits Packet Buffer. : Static routing: 124 Static routes Static MAC Entries: 256 entries : Power Supply: Internal AC Power Supply, Switch Category :- Gigabit Managed Switches Layer 2 Features : Spanning Tree (SP) 802.1d : RSTP 802.1, 802.1s MSTP : Loopback Detection : Link Aggregation LACP 802.3ad: Minimum 8 groups per device and 8 ports per group ; Port Mirroring : One-to-One / Many-to-One : Jumbo Frame: 10K Bytes : Dual image & Dual configuration : Multicast Filtering

Supply/Installation/Testing & Commissioning of RJ-45 Cat-6 Shuttered NET JACK Modular Series of Modular Switch,Modular Plate,Cover in front,Modular blanking plate & suitable GI box etc ISO/IEC Certified Havells/ Legrand/Panasonic/Anchor Rooma Plus/Schneider/Eq Make & shall be approved before execution of work.

Supply & Installation of IP-20 & IK-08, UL Listed Wall mounted Double Section Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, Vertical Mounting Rail 1.6 MM with 'U'Marking, with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19" angles with wall mounting provision on wall. Accessories like: 1 No of 19" 1U Horizontal Cable manager, 1 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware, 1 No of 19" 1U, mountable socket strips with 5 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with Suitable Anchor fastner etc as required.All as per pre approved by Engineer in charge For additional technical parameters of products/ work, refer Annexure "A" attached with this BSRof D-Link or Equivalent Make Including Supply of power extension cord etc:- 9 U Rack with Width 600 mm & Depth 400 mm + 100 mm

(25-KVA DG Set)

Supply/Installation/Testing and Commissioning of CPCB IV + or better norms along with having Prime Power Rating of 25KVA 3-Phase Silent mode Diesel Generator (DG Power Set) of :FG-Wilson(CATERPILLAR)/Cummins/ASHOKA LEYLAND (CSH)/Kirloskar Make" With Following technical Specifications :- (Air Cooled type) (A) comprising of Diesel engine with 415 AC 50Hz of: (i) Engine Power RATING =25KVA (power factor 0.8)=20 KW (ii) Engine SPEED= 1500RPM (iii) Engine Aspiration = Liquid cooled (Turbo charged) (iv) Engine COOLING= Radiator /Liquid cooler (v) Engine Starting= 12 V DC Electric (vi) Should have Rotary Fuel Pump (vii) Should have Pistons with oil Gallery and Piston Cooling jet (viii) Governor= Electronic AO (ix) Should operate from -45 Degree (B) Alternator:- (i) Alternator Type = Brushless Self Excited and Self Regulated (ii). Alternator Rating =25kva (iii) Voltage =415V, 3-PHASE 4Wire (power factor 0.8)= (iv). Frequency = 50HZ (v) Speed=1500rpm (vi) Protection= IP 23 (vii) Voltage regulation= Automatic voltage regulation of less than ± % (viii). Wave regulation= less than 3% distortion (ix) Voltage regulation =± 1% (iix) Noise level=less than <75DB at 1mt. Distance Also should Common Base Frame Batteries ,Leads and Stand Anti Vibration Mountings Residential type Exhaust Silencer,Exhaust Below,First Fill of Lubricating oil,SOUND PROOF ACOUSTIC ENCLOSURE(CPCB-4) APPROVED) Standard Control panel IP-55,AMF Panel and ENGINE should having 4 Cylinder,Piston with oil Gallery and Piston Cooling jet, powder coated sheet metal fabricated sound proof with Silencer Canopy also adequate capacity 63-100Amp TPN MCCB of Seimens/ABB/Legrand/L&T,12 volt Batteries with Charger including cost all allied accessories ,income taxes,sales taxes,GST loading unloading carriage up to site and first fill 100 litres fuel Diesel for testing Complete.

Supply/Installation/Testing and Commissioningof Maintenance free Chemical EARTHING SYSTEM Sets (Vertically installation of EARTHING SYSTEM) using Earthling copper bonded Earthing Rods of 6ft long with molecular bonding along with 2 bags (11.5 kg each) of Ground Enhancement Gem Material with each Earth Rod to reduce the soil resistivity complete job confirm to relevant international/Indian standard. The rod is to be laid vertically in a bore of required dia/depth duly excavated bore well including cost of excavation of bore well ,making of surface structure in brick/cement concrete material as per drawing annexure safe Earthing electrode.The Earth rod is to be connected with 20mm wide copper strip laid through Weather proof PVC Pipe of Prince make up to DG ENGINE,ALTERNATOR , CONTROL PANEL & CANOPY in one run including cost of COPPER Strips complete jobs Four Separate Earthings for each DG ENGINE,for Alternator ,Control Panel & for Canopy

Construction of DG Set Foundation of 10 ft in L x 5ft in W x 4ft (2ft U/G and 2ft A/G Approximately in Ht. Ft in M20 cement concrete Ratio 50mm thick cement conc. flooring on the top of floor, also plastering in 1:6 mix, including cost of all materials form works, 40x40x5mm angle iron truss with 26 gauge CGI Sheet roofing dully fitted with J-hooks to cover the DG set.The angle iron truss should be rested (erected/Supported) on Posts of G.I or Jindal 6`` dia pipes having 1-½ ft x1-½ ft , 12mm thick Base, side, Top plates fitted with nut & bolts.The truss height should be at least 8 ft Complete job.The Job Shall be Monitored by concerned sub-division site incharge (Civil Engineer)

Supply/Laying/Testing and Commissioning of 3.5 Core 70 mm sq. Al armored XLPE Insulated,PVC cable Havells/KEI/RR Kabel/Paramount Make. Including Supply/Laying of HDPE Pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (100 cm below ground level) including excavation and refilling the trench of standard make as approved.The cable shall include end termination lugs with its crimping /taping.

(Air Conditioner)

Supply/Installation/Testing & Commissioning of 1.5 TON inverter type split Air Conditioning system suitable for operation on AC supply single phase 220 V. The indoor unit fitted on wall by employing suitable clamps and the outdoor unit fitted on the wall by using suitable angle iron stand fitted with nuts/bolts outside the room to avoid noise, including standard length of suitable size copper tubing covered with nitrilic foam, topping up with refrigerant for additional length of piping if required, PVC flexible drain pipe, suitable capacity 3 core sheathed/ pvc insulated coper cable and a battery operated wireless remote unit. the job also includes repairs to walls wherever the same are cut and the AMC of AC for a period of one and a half year from date of successful commissioning. (Mitsubishi/Toshiba/O-General make)olt & stand ,Copper piping etc & all other allied accessories, installation charges,GST, income tax , carriage etc Complete job.The job includes CMC (reckoned from date of successful commissioning) for a period of Two years.(Subjected to site requirement)

FIRE DETECTION

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete asrequired.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/ 1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR)insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supplying,Installation,Testing and Commissioning of CO2 Type Fire Extinguisher 4.5 Kg. Capacity ISI Mark(IS:15683)suitable for 'B' and 'C' class fires - inflammable liquids, gaseous fires like L.P.G. and acetylene, and electrical fires

Supplying,Installation,Testing and Commissioning of MAP 90 ABC Type Fire Extinguisher 4.0 Kg. Capacity ISI Mark(IS:15683)suitable for Class A/B/C Type Fires .

Sanitary and Plumbing

Providing and fixing white vitreous china pedestal type water closet(European type) wall hung including painting of fittings and brackets, cutting and making good the walls and floors wherever required: (For Specially Abled) W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid , 10 liter low level white vitreous china flushing cistern and CP flush bend with fittings and C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing Under Counter wash basin,with 32 mm Waste Coupling and other allied accessories including cutting and making good the walls wherever required:-White Vitreous China Under Counter Wash basin.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040mm bowl depth 250mm.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing mirror of superior glass (of approved quality) and ofrequired shape and size with plastic moulded frame of approved makeand shade with 6 mm thick hard board backing Rectangular shape 1500x450 mm

Providing and fixing toilet paper holder C.P. brass (Heavy Duty) Jaquar/Hindware or equivalent brand all complete.

Providing and fixing C.P Brass Soap Dish (Heavy Duty) Jaquar/Hindware or equivalent brand all complete.

Providing and fixing CP brass towel rail complete with CP brackets fixed to wooden cleats with CP brass screws 600mm long (Heavy Duty) Jaquar/Hindware or equivalent brand all complete.

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 all complete.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

Providing and fixing Stainless Steel Retractable Sink Basin Water Drain Pipe of approved quality & make and as per the direction of Engineer-in-charge. (For Kitchen Sink) (Jaquar/Hindware or equivalent all complete.

Providing and fixing CP Brass Sink Mixer with Regular Swivel Spout of quality & make as approved by Engineer in charge.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing. 110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B.

Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing. 75 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B.

Providing and fixing of Rain Water pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-A

Providing and Fixing of Floor Traps 110 mm with double chrome plated Cover one Grated and one closed and all other fittings required. Makes:- Astral/SFMC/Finolex all complete.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement: 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarsesand (zone- III): 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floatingcoat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 all complete.

Supply, Installation of PVC Gully Trap of Size 110 mm (Heavy Duty) all complete.

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms,lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of P.V.C pipes including bed concrete as per standard design :110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B all complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.(SDR-11) Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.15mm nominal outer dia pipes

20mm nominal outer dia pipes

25mm nominal outer dia pipes

32mm nominal outer dia pipes

Providing and fixing Polyethylene- Aluminum- Polyethylene (PE-ALPE) Composite Pressure Pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature upto 80ºC, including all special fittings of composite material (engineering plastic blend and brass inserts whereverrequired) e.g. Elbows, tees, reducers, couplers and connectors etc.This includes testing of joints complete as per direction of the Engineer-in-charge:Internal work-exposed on wall with clamps at 1.00 meter spacing 25mm nominal outer dia pipes.

32mm nominal outer dia pipes

40mm nominal outer dia pipes

Providing and fixing Polyethylene- Aluminum- Polyethylene (PE-ALPE) Composite Pressure Pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature upto 80ºC, including all special fittings of composite material (engineering plastic blend and brass inserts whereverrequired) e.g. Elbows, tees, reducers, couplers and connectors etc.This includes testing of joints complete as per direction of the Engineer-in-charge:External work including trenching and refilling etc complete 40mm nominal outer dia pipes.

Providing and fixing unplasticised PVC connection pipe with brass unions:45 cm length 15 mm nominal bore

Cutting holes upto 30x30 cm in walls including making good the same with common burnt clay F.P.S.(non modular) bricks

Supplying and Fixing of Elastomeric foam Insulation made from Nitrile Rubber with Density not less than 50 Kg/Cu.m,Thickness 10 mm for a Temp Range of -40 Deg C to 105 Deg C

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 16 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.(Heavy Duty) 65 mm Diameter

40 mm Diameter

50 mm Diameter

32 mm Diameter

Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of class designation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design

Constructing septic tank, of size 5.0 mx 2.5 m x1.80 m approx. height(Height to be fixed as per site requirement i.e. below invert level of last manhole , in B/W, 350/230 mm thick ( minimum) walls Details be given at the time of payment.

Providing and fixing 35 liter capacity water heater Gyser of approved brand of Venus/ Recold/ Jaquar/ Hindware / cera or equivalent brand including its fixing at desired position complete in all respects as per directions of Incharge Engineer..

Providing and fixing 50 liter capacity water heater Gyser of approved brand of Venus/ Recold/ Jaquar/ Hindware / cera or equivalent brand including its fixing at desired position complete in all respects as per directions of Incharge Engineer..

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Supply,Installation,Testing and Commissioning of Open Well Submersible Pump with a Discharge of 6.0 Cu.m/hr @Head of 45 Meters Complete with all accessories including header Pipes, allied materials and automatic Control Panel Details be given at the time of payment..

Passenger Lift

Supply, Installation,Testing and commisioning of 8 Passenger Lift with the following Specifications as per IS:-14665 (2000) Operating Voltage:- 415 Volts 3 Phase Hoistway size :- 1850mm X 1650mm Pit(mm) :- 1600 mm Capacity (kgs) :544 Kg, 08persons Rise (m ) :22m Appx. STOPS: 3 Stops With (all opening on the same side) Drive :Microprocessor Based V3F Drive. Machine : P M Gearless (Located in shaft on top of guide rails) Car Finish : Rear Mid Panel = SS Honey Comb Rear Corner Panels = SS Honey Comb Side Mid Panels = SS Honey Comb Side Corner Panels = SS Honey Comb Front Panels = SS Honey Comb False Ceiling Finish: SS Mirror Finish Hand Rail :Stainless Steel Hair Line Finish Handrails on rear car panel. Ventilation:Cross flow fan Flooring:Granite Flooring Door Operator: DC Door Operator Standard Features : Anti-nuisance Car Call Protection Control System :- Simplex automatic operation Overload Device Nudging Floor Annoucement Syatem with Music Emergency Firemen’s Service Emergency Car Light Unit Infrared Curtain Door Protection Full Car Operating Panel 8 Press & Speak Phone Door Time Protection Emergency Alarm Button Extra Door Time of Lobby & Parking Door Open/Close Button Automatic Rescue Device with Dry Maintenance Free Batteries Auto Fan Cut Off Provision of CCTV Camera Fire Rating of Landing Doors for 2 Hours Floor Annuciator with Music Provision of 3 way intercom with instrument. Indicators in Car and Landings

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Filling and Landscaping

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts

Filling with River / RBM materials, incl. rolling etc. all job complete

Supply, stacking and laying of GSB Naturally occurring gravel close graded maximum aggregate size range 75mm granular sub base course including sorting, spreading to template, watering and consolidation to required gradient and camber with 80-100KN road roller all inclusive leads, lifts, loading, unloading carriage of materials from approved source to site of work complete. Finished work to be measured.

Supplying and stacking at site Good Earth ( Suitable for turf) incl. royality carried from approved scource upto site of work ramming dressing and watering in 15/22 cm layers incl. levelling spreading and consolidation with power road roller of 8 to 10 tone capacity ( to req. gradient and chamber with all leads and lifts carriages.

Road Work

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil

P/L of Bulder Filling incl. with ramming, dressing, watering and compacting with PRR all inclusive leads, lifts, loading, un-loading, cost and carriage of material involved complete.

Supply, stacking and laying of GSB Naturally occurring gravel close graded maximum aggregate size range 75mm granular sub base course including sorting, spreading to template, watering and consolidation to required gradient and camber with 80-100KN road roller all inclusive leads, lifts, loading, unloading carriage of materials from approved source to site of work complete. Finished work to be measured.

Supply, stacking and laying of WBM grade 2nd with specified graded stone aggregate 63mm - 45mm size broken quarry stone @0.92cum/10 sqm and using of screening 11.20mm size @ 0.135cum/10sqm and binding material @0.06cum/10sqm of road surface including sorting, spreading to template, watering and consolidation to required gradient and camber with (80-100) KN road roller all inclusive leads, lifts, loading, unloading, head load if any and carriage of materials from approved source to site of work complete (To be laid as per guide line of MOST specification). Finished work to be measured

Providing/ laying and embedding of R.C.C. pipes incld. trench excavation in all status of surface to required width/depth and making of necessary cushioning with required material jointing of pipes all inclusive cost and carriage of pipes upto site of work complete. 18" dia RCC spun pipes

R/Wall

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil :

P/L of dry stone soling duly hand packed with ramming, dressing, watering and compacting all inclusive leads, lifts, loading, un-loading, cost and carriage of material involved complete.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) complete.

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) incl. carriage all complete.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more .including all carriage involved complete.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing but excluding the cost of centring, shuttering and finishing with. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc

Centering and shuttering including strutting, propping etc. and removal of form for: Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc

12mm Cement plaster of mix:1 : 4 ( 1 cement : 4 fine sand) all complete

Providing and fixing of 75mm dia PVC type-B pipe in wall (weep holes) including cushioning cutting and placing as required.

Pumping out of water caused by springs, river seepage, broken water mains or drains and the like

Carriage of materials from approved source to site of work:- Stone aggregate for an average lead of 10Kms

Sand for an average lead of 10Kms.