REPAIR / MAINT CRANES AND CONNECTED WORK AT ARMY AREA JODHPUR UNDER GE (ARMY) NO. 01

Amount

Material and Labour for disconnecting the electric supply from existing EOT crane panel, taking down on ground gear box of the cranes and including repair/servicing , greasing etc of hoist motor, Long Travel/Cross Travel motor from a height of upto 40 feet including cleaning of slots, replacement of laminated sheets, rewinding cut coils of burnt winding wire with super enamelled copper winding wire of existing size, backing, varnishing and re-fixing in its position, making all electric connections of motor and testing on full load of capacity of as per existng location (ie. 0.5 to 2 hp/3 to 5 hp/7.5 to 15 hp motor ) open up for examination of Engr-in-Charge by loosening the coupling , foundation nuts, bolts & washers etc, draining out the complete gear oil, taking out grease cleaning the complete gear box with K.oil and reassembling the gear box after replacement of defective / worn out parts ie brass gears, tapper roll bearing, oil seal, coupling, foundation nuts, bolts, washers etc of existing make, size and capacity including refilling the fresh gear oil, grease complete and making the gear box leak proof by fixing the suitable oil seal. including taking up and refixing with crane and testing on completion all as specified and directed. Note :- (a) Replacement of new parts ie Tapper Roll Bearing, Brass Gear, Oil Seal, Coupling & Foundation nuts, bolts, washers and providing fresh gear oil as well as fresh grease will be measured and paid separately under respective items as supply only. (b) Item should be measured only one for 2 in a contract period as per requirement.

1(a) Capacity of 2 to 5 Ton

1(b) Capacity of 2 to10 Ton

1(c) Capacity of 3 to 15 Ton

Material and Labour for disconnecting the electric supply from existing EOT crane panel, taking down on ground gear box of the cranes and open up for examination of Engr-in-Charge of capacity 40 Ton by loosening the coupling , foundation nuts, bolts & washers etc, draining out the complete gear oil, taking out grease cleaning the complete gear box with K.oil and reassembling the gear box after replacement of defective / worn out parts ie brass gears, tapper roll bearing, oil seal, coupling, foundation nuts, bolts, washers etc of existing make, size and capacity including refilling the fresh gear oil, grease complete and making the gear box leak proof by fixing the suitable oil seal. including taking up and refixing with crane and testing on completion all as specified and directed. Note :- Replacement of new parts ie Tapper Roll Bearing, Brass Gear, Oil Seal, Coupling & Foundation nuts, bolts, washers and providing fresh gear oil as well as fresh grease will be measured and paid separately under respective items as supply only.

Material & Labour for disconnecting the electric supply, dismantling and opening of E H thrustor and thrustor brake drum 50 mm to 250 mm dia of EOT cranes and serevicing complete and reassembling the thrust brake drum in its position including servicing of brake assembly complete all as specified and directed.any type and make of capacity 2,5,5/2 Ton servicing /overhauling complete at site and reassembling the same in its position complete all as specified and directed. Note:- Rates for brake leather of any type and dia deemed to be included in quoted rates.

Material & Labour for taking down old U/S brakes assembly from EOT cranes including S & F of AC Solenoid Brakes assy, suitable for capacity 2 to 5 Ton EOT Cranes, testing of crane on full load complete all as specified and directed.

Material & Labour for taking down old U/S brakes assembly from EOT cranes including S & F of AC Solenoid Brakes assy, suitable for capacity 2 to 10 Ton EOT Cranes, testing of crane on full load complete all as specified and directed.

Material & Labour for taking down old U/S Electro hydraulic thrustor fom EOT cranes, S & F new Electro hydraulic thrustor with motor complete assembly with accessories of capacity 3 to 15/40 Ton EOT Cranes, testing of crane on full load complete all as specified and directed.

Material & Labour for disconnecting the electric supply, dismantling and opening of E H thrustor and thrustor brake drum 50 mm to 250 mm dia of EOT cranes and serevicing complete and reassembling the thrust brake drum in its position including servicing of brake assembly complete complete all as specified and directed.any type and make of capacity 10/2, 15/3 Ton servicing /overhauling complete at site and reassembling the same in its position complete all as specified and directed. Note:- Rates for brake leather of any type and dia deemed to be included in quoted rates.

Material & Labour for taking down old U/S brakes assembly from EOT cranes including S & F of AC Solenoid Brakes assy, suitable for capacity 10/15 Ton EOT Cranes, testing of crane on full load complete all as specified and directed.

Material & Labour for taking down old U/S Electro hydraulic thrustor fom EOT cranes, S & F new Electro hydraulic thrustor with motor complete assembly with accessories of capacity 10/2 Ton EOT Cranes, testing of crane on full load complete all as specified and directed.

M & L for taking down steel wire rope of size up to 21 mm dia from EOT/HOT Cranes hoist drum and load hook after loosening the holding nuts and bolts etc from EOT Crane of capacity 2,5,5/2,10/2,15/3,20 Ton and cleaning of complete drum assembly and rope with k oil /thinner and applying/ filling of fresh grease/Oil to wire rope and reassembling fixing etc complete all as specified and directed. Note :- Fresh Gear oil,grease will be measured and paid separately under respective items.

M & L for taking out contaminated grease from all greaseble parts/ gears by opening care fully of HOT Crane (such as chain pulley, drum shaft, postal bearing & load hook etc) and cleaning of complete assembly with Koil /thinner and M&L for applying/ filling of fresh grease to all parts of HOT cranes of capacity 2 Ton and reassembling fixing etc complete all as specified and directed. (Fresh grease shall be paid against relevant item of Sch A)

Supply & fixing metal (Steel/Brass) gears (as per existing gear/ sample) duly casted/fabricated and cutting teeth as required suitable to accommodate in the cranes Gear Box complete all as specified and directed for the following capacities/ sizes of cranes. (a) 2 to 10Ton capacity of crane Note : Dismantling, taking down and reassembling of gear box will be carried out against Sl No. 1 items

All as per item No 12.00 here-in-above but capacity of crane is 3 to 15/40 Ton

Disconnections of electric connections of EOT cranes at height of upto 40 feet including cleaning the surface of copper round bus bar size up to 8 mm dia with emery paper complete making free from dust for easy collection of current by phase collector of crane from bus bar complete all as specified and directed.

M & L disconnecting electric connections, Taking down old burnt main supply cable, S&F of PVC insulated & seathed with bare annealed copper conductor cable, multistrand, Copper conductor 25 Sqmm, 4 Core confirming to IS 694-1990, 1100 V grade complete all as specified and directed.

M & L disconnection of electric supply from crane panel including S&F of pendent PVC insulated & seathedwithbare annealed copper conductor cable, multistrand, Copper conductor 1.5 Sqmm, 10 Core confirming to IS 694-1990, 1100 V grade with and including GI wire 6 SWG, Steel rings, binding wire for binding the cable and GI wire together on steel rings not less than at one mtr gap and stretching of GI wire and cable and binding at both ends of the crane complete all as specified and directed.

All as per item No 16.00 here-in-above but 2.5 sqmm,10 core cable

M & L for disconnecting old U/S pendent box and S & F new Pendent box, as per existing size, fabricated out of 18 SWG MS sheet having suitable opening at top for pendent cable using cable entry glands and two side hooks on the top of either side for holding the chain guard of pendent cable, fixing metal outer cover, complete with operating push button (Red and green), mushroom head emergency stop button, LED light indicator duly prewired inside, having rear door opening and locking arrangement incl two coat of syntactic enamel paint of approved colour over a coat of primer complete all as specified directed.

S&F in repair of push button mushroom head / Hexagonal type (Red or green colours as required at site at the time of execution) complete all as specified and directed.

M & L for taking down old U/S phase indicator lamp set (RYB) complete after disconnecting electric connections and supply and fixing phase indicator lamp set (RYB) LED type including making electric connections complete all as specified and directed.

M & L for taking out old u/s AC contactor any capacity and S & F freedom series type 4 pole, 415 volts with coil as per existing, auxiliary contact block with No + NC and current rating 10 to 18 Amps, 4/7.5 KW and including making necessary electric connections and testing of circuit on full load complete all as specified and directed.

All as per item No 21.00 here-in-above but current rating 20 to 30 AMPs, 15 KW, 4 pole.

All as per item No 21.00 here-in-above but current rating 40 to 50 AMPs, 22 KW, 4pole .

All as per item No 21.00 here-in-above but current rating 100/110 AMPs, 4pole

Taking out old unserviceable MCCBs up to 200 Amp rating and Supply and fixing for MCCB, 4 pole,415Volt, 18 KA including cable lugs of suitable size as per site requirement complete testing, commissioning complete to the entire satisfaction of Engr-in-charge, the following capacity of (a) 40 Amps.

All as per item No 25.00 here-in-above but current rating 63 Amps

All as per item No 25.00 here-in-above but current rating 100 Amps

Supply and fix in replacement of electronic mototr protection relay capacity 2-6.5/4-11 Amp for motor protection making all incoming and outgoing electric connection complete all as specified and directed.

Supply and fix in replacement of electronic motor protection relay capacity 8-22 Amp for motor protection making all incoming and outgoing electric connection complete all as specified and directed.

Supply and fix in replacement of timer for motor starter 0-30 sec./3-30 Sec making all incoming and outgoing electric connection, make and model as per existing location complete all as specified and directed

M&L for Earthing complete with galvanized steel earth plate electrodes 600x600x6 mm thick buried directly in ground eath (earth pit not less 2.25 m deep below ground level) with top edge of the plate not less then 1.5 mtr below normal ground level connected to galvanized iron earthing strip 32mm x6mm thick by means of bolt nuts check nuts and washers of galvnised iron or steel all as specified & shown in electrical plate No.3 of MES SSR part-I connected to earth test point as specified and testing on completion including provision of 40 mm dia light grade pipe & watering pipe shall be 20 mm bore medium grade including all excavation & earth work in any type of soil incl PCC for pit (1:3:6) type C-1 with RCC cover in PCC(1:2:4) including charcoal , salt funnel GI pipe 40 mm dia light grade up to to 7.5 mtr length ,all as directed at site.

Material and labour for Earthing strip , galvanised iron strip 30 x 6 mm , burried in ground or fixed to pole/ wall with saddles etc as specified and directed. Earth work if required shall be measured against respective item.)

Taking out of existing unservicable light fittings of any shape and size and removing from the site . Supply and fixing high efficiency round LED high-bay luminaire with aluminium die cast housing with high lumen efficacy of 110lm/W product code LHPN-100-C-V1 of Make : Orient Electric or equivalent light fitting, 100 Watts with all necessary required fittings ie, clamps, nuts, bolts and suitable for operation over voltage range of 140 V to 270 V, duly housed in pressure die cast aluminium housing, compressing of LED with individual optical lens, electronic driver with THD <10%, efficiency >85% and PF more than 0.90, confirming to IP65, rendering color index of 75 with cool day light output.

Taking down old U/S single Phase Preventer from crane panel board including S&F Single Phase Preventer suitable for motor protection of EOT cranes and making all incoming and out going electric connections complete all as specified and directed.

Supply only Tapper Roll Bearing of No 6206/6306/30232/30226/30216/ 30205/30215/33207 or any other size as per existing gear box bearing complete all as specified and directed .

Supply only Gear Oil (20W40) suitable for crane gear box complete all as specified and directed.

Supply only in sealed container packing grease suitable for crane gear box complete all as specified and directed.

Supply only Oil seal (as per sample) suitable for crane gear box complete all as specified and directed.

Disconnecting electric connections, Taking down old U/S CT including S&F of current transformer of capacity 100 to 150 VA, of input 440 volts, out put 110 volts for EOT crane up to 2/3/5 ton capacity, making all incoming and out going electric connection complete all as specified and directed.

All as per item No 39.00 here-in-above but of capacity 300VA for EOT Crane up to 15 Ton capacity

M&L for MS cross arms, bracing supports, clamps and back plate fixed to trusses/ girders / angle iron or in various parts of crane/ machines at any height in work shop cranes fabricated from structural steel sections including bolt, nuts and washers welding bending cold or hot drilling holes for bolt in any shape or size as indicated or directed with and including of one primer coat, one under coat and one finishing coat of aluminium paint etc complete all as specified and directed

M & L for taking out old unserviceable/weaked SWR rope and S & F round strand steel wire rope RHO/LHO/RHL/LHL as per IS dia of 8/10 mm to suitable for Crane hooks up to capacity of 10 Ton and connected clamp nut bolts fixed complete all as per directed

M & L for taking out old unserviceable/weaked SWR rope and S & F round strand steel wire rope RHO/LHO/RHL/LHL as per IS dia of 12/15 mm to suitable for Crane hooks up to capacity of 10 Ton and connected clamp nut bolts fixed complete all as per directed

Supply and fixing in repair crane pulley with hook suitable for crane of capacity 2 Ton complete with all accessories including taking down old unserviceable pulley with wire rope and reassembling the same after replacement of pulley,testing the crane for full load complete all as specified and directed.

Supply and fixing in repair crane pulley with hook suitable for crane of capacity 5 Ton complete with all accessories including taking down old unserviceable pulley with wire rope and reassembling the same after replacement of pulley,testing the crane for full load complete all as specified and directed.

Supply and fixing in repair coupling bolt 12mm x 100mm with bush URB complete as specified and directed

Supply and fixing in repair limit switch as per sample with limit ring complete suitable for crane of capcity 2/5/10/15/40 Ton as specified and directed

M & L for servicing of air compressor of capacity 10HP, 215 PSI complete as per manufacturer norms all as per directed including replacement of compressor oil, belts etc.

M & L replacement of shaft pulley as per existing of air compressor of capacity 10HP, 215 PSI including eplacement of shaft key, bearing etc as required all as specified and directed by Engineer-in-Charge.

Material and Labour for load test of EOT crane , ie. push, travelling (long travel/cross travel) , hoist motor and all connected items of EOT crane and After servicing record should maintain for future examine complete all as specified and directed by engr-in charge. (a) Capacity of 2 to 5 Ton

All as per item No 50.00 here-in-above but Capacity of 2 to10 Ton

All as per item No 50.00 here-in-above but Capacity of 3 to 15 Ton

All as per item No 50.00 here-in-above but Capacity of 40 Ton

PANWAR ELECTRICALS (BID ID -3149352)