Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹42.5 CrAccepted-AOC | ₹42.5 Cr | L1 | Accepted-AOC AOC |
| 2 | L2₹42.5 CrRejected-Finance 32 9 EC ROAD DEHRADUN 248001 | DEHRADUN | UTTARAKHAND | 248001 | ₹42.5 Cr | L2 | Rejected-Finance Highest Rate Quoted by bidder |
| 3 | Rejected-Technical | - | - | Rejected-Technical Not Technically Qualified |
Tender Value
₹42.6 Cr
EMD Value
₹67.6 L
Closing Date
25 Jun 2024, 5:00 pmClosed
General Manager (Garhwal)
Office of Chief General Manager, Construction Wing, Uttarakhand Peyjal Nigam, Kamla Nagar(Opp. ONGC Hospital), Dehradun
CONSTRUCTION OF OFFICE BUILDING FOR UTTARAKHAND PEY JAL NIGAM AT DEHRADUN DISTRICT DEHRADUN
2024_MDPEY_72224_1
2173/ Nivida(Garhwal) Dehradun /69 Dated10-06-2024
Open Tender
Civil Works
540 days
DEHRADUN DISTRICT DEHRADUN
Please refer tender document
3 documents required · 3 mandatory
₹11,800
PM,Const.Unit, UKPJN, Dehradun
₹67.6 L
Dehradun
26 May 2025
11 Jun 2024
27 Jun 2024
11 Jun 2024
25 Jun 2024
14 Jun 2024
13 Jun 2024
Amount
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
Diluting and injecting chemical emulsion (chlorpyriphos/Lindane E.C 20% with 1% concentration) at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surface of the excavation made for the foundation of the building, soil under floor,apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of building shall be measurd for payment.)
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
M-10 grade plain cement concrete (cement content considered @ 220 kg/cum)
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level
All works above plinth level upto floor V level
Add for using extra cement in the items of design mix over and above the specified cement content therein.
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more
Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete
Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses,plinth and string courses etc
Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers
Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts
Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick
Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)
12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)
15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)
6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick
Marble stone flooring with 18 mm thick marble stone, as per sample ofmarble approved by Engineer-in-charge, over 20 mm (average) thick baseof cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed withgrey cement slurry, including rubbing and polishing complete with Makrana white second quality :
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: 10.14.1 Profile B 10.14.1.1 Fixing with adjustable lugs with split end tail to each jamb
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides
Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).
Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :5.5 mm thick glass panes
Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 125x64x1.90 mm
Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete :150 mm
Providing and fixing ISI marked 85x42 mm oxidised M.S. pull bolt lock conforming to IS : 7534 with necessary screws bolts, nut and washers etc. complete.
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete..
Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer
White washing with lime to give an even shade : New work (three or more coats)
Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture
Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
Steel work welded in built-up sections / framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works.
Steel work welded in built-up sections / framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works.
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarsesand : 6 graded stone aggregate 20 mm nominal size)
Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)
Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. Using grade 'A' sealing compound conforming to IS: 1834.
Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign material etc. and lining out complete. New work (Two or more coats)
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent
Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Marble work
Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)
Providing & fixing in position Phenol bonded Bamboowood panelled or panelled and glazed shutters for doors windows, clerestorey windows with pre-molded 30mm thick planks, in approved colours, texture & finishe. It shall have 10mm wide, 25mm deep grove to fit in panels.The bamboo wood shall have minimum density of 1000 Kg/cum, minimum Hardness 1000 Kgf. All styles and rails shall have profiled interlocking system locked in place by bamboo pins, all complete as per direction of Engineer in charge. (The panelling will be paid for separately).
Providing and fixing stabilized fiberglass reinforced plastic sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 2mm thick corrugated or step down
Providing & fixing in position Phenol bonded Bamboowood wall cladding at all height with planks of sizes 10mm thick, 1800mm length (minimum) and 130 mm wide (minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC), with necesasary profiled edges fixed with 40mm SS screws 5 nos in each tile to frame work made of second class teak wood of size 20x15 mm in centre of each tile and bottom and top of work height, 40x15mm placed at ends of each tile. The cladding shall be laid over backlayment of 1.00 mm thick expanded polyethylene foam of density 40kg/cum in two layers, first layer on wall surface before fixing wooden frame and second layer on frame under cladding. The bamboowood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :
Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.
Providing and fixing white viterous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & CP flush bend with fittings & CI brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.
Providing and fixing water closet water closet squatting pan (Indian Type W.C Pan) with 100mm sand cast iron 'P' or 'S' trap, 10 ltrs low level, PVC flushing cistern with manually controlled device (handle lever)conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever requiredand as per direction of Engineer -In-charge: White Vitreous China Orissa pattern W.C pan of size 580 x 440 mm with integral type foot rests.
Providing and fixing C.P. brass short body bib cock with flange of approved quality confirming to IS: 8931 15mm nomonal bore
Providing and fixing wash basin with CI/MS brackets, 15mm CP brass pillar taps, 32mm CP brass waste of standard pattern, including painting of fitting and brackets, cutting and making good the walls wherever required. White Vitreous China wash basin (oval) size550 x 400 mm with single 15mm CP brass pillar tap
White Vitreous China flat back wash basin size550 x 400 mm with single 15mm CP brass pillar tap
Providing & fixing PTMT Bottle trap for wash basin and sink Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 263gms.
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm and 340 x 410 x 265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass union and G.I clamps complete, including painting and brakets, cutting and making good the walls and floor wherever required One urinal basin with 5 litre white PVC automatic flushing cistern
Providing and fixing C.P. brass quality angle valve15 mm dia. For basin mixer and gyser points of approved quality, confirming to IS : 8931 15mm nomonal bore
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make confirming to IS : 8931. 15mm nomonal bore
Providing & fixing PTMT liquid soap container109mm wide,125mm high and 112mm distance from wall of standard shape and brackets of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms.
Providing & fixing PTMT towel ring trapezoidal shape 215 mm long,200mm wide with a minimum distance of 37mm from wall face with concealed fitting arrangement of approved quality and colour weighing not less than 88 gms.
Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.
Providing & fixing 600x450mm beveled edge mirror of superior glass ( of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washer complete.
Providing and fixing toilet paper holder C.P. brass
Centrifugally cast (spun) iron socketed pipe as per IS 3989. 75mm dia
Centrifugally cast (spun) iron socketed pipe as per IS 3989 100 mm dia
Providing and fixing M.S holder-bat clamps of approved design to sand cast iron/sand cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1cement:2coarse sand: 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc For 100 mm dia pipe
Providing and fixing M.S holder-bat clamps of approved design to sand cast iron/sand cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1cement:2coarse sand: 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc For 75 mm dia pipe
Providing and fixing bend of required degre with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm Centrifugally Cast (Spun)Iron S & S pipe as per IS : 3989
Providing and fixing plain bend of required degree 100 mm Centrifugally Cast (Spun)Iron S & S pipe as per IS : 3989 75 mm
Centrifugally Cast (Spun)Iron S & S pipe as per IS : 3989
Providing and fixing single equal plain junction of required degree with access door, insersion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100 mm Sand cast iron S & S as per IS 3989
75x75x75 mm Sand cast iron S & S as per IS 3989
Providing and fixing double equal plain inverted branch of required degree 100x100x100x100 mm Sand cast iron S & S as per IS 3989
Providing and fixing terminal guard. 100 mm Sand cast iron S & S as per IS 3989 75 mm
Sand cast iron S & S as per IS 3989Providing and fixing collar100 mm
Sand cast iron S & S as per IS 3989 75 mm
Sand cast iron S & S as per IS 3989
Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter: 100 mm
Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter: 75 mm
Providing and fixing M.S stays and clamps for sand cast iron / Centrifugally Cast (Spun) Iron Pipes iron pipes of diameter. 100 mm
Providing and fixing M.S stays and clamps for sand cast iron / Centrifugally Cast (Spun) Iron Pipes iron pipes of diameter. 75 mm Internal Work - Exposed on wall
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. 15 mm nominal outer dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. 20 mm nominal outer dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. 25 mm nominal outer dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. 32 mm nominal dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. Concealed work including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. Concealed work including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. Concealed work including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. Concealed work including cutting chases and making good the walls etc. 32 mm nominal outer dia Pipes
External Works Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings. This include jointing of pipes & fitting with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in charge. 50 mm nominal outer dia Pipes
External Works Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings. This include jointing of pipes & fitting with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in charge. 62.50 mm nominal outer dia Pipes
Providing & fixing ball valve (brass) of approved quality, High or low pressure with plastic floats complete 15 mm nominal bore
Providing & fixing ball valve (brass) of approved quality, High or low pressure with plastic floats complete 20 mm nominal bore
Providing & fixing ball valve (brass) of approved quality, High or low pressure with plastic floats complete 25 mm nominal bore
Providing & fixing gun metal gate valve with C.I wheel of approved quality, (Screwd end) 32 mm nominal bore
Providing & fixing gun metal gate valve with C.I wheel of approved quality, (Screwd end) 40 mm nominal bore
Providing & fixing gun metal gate valve with C.I wheel of approved quality, (Screwd end) 50 mm nominal obore
Providing and placing on terrace (at all floor levels polyethylene water storage tank ISI : 12701 marked water storage tank with cover and suitable locking arrangement and making necessary holes for inlet outlet and overflow pipes but without fittings and the base suport for tank
Constructing masonary chamber 30x30xx50 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement : f fine sand) for gate valve with C. I. susface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1 : 3 ( 1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design with F. P. S. bricks
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110mm Dia
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110mm
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 110mm Bend
Providing and fixing Unplasticised -PVC pipe clips of approved design to Unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm
Providing and fixing 40mm dia with length not less than 700mm waste pipe for sink and wash basin. complete job.
Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil
Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.
1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)
Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30
Sepration Membrane of Impermeable Plastic Sheeting 125micron Thick
Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/expansion, construction & longitudinal joints (10 mm wide x 50 mmdeep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. Cement concrete prepared with batch mixing machine
Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)
Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. Using grade 'A' sealing compound conforming to IS: 1834.
Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking paint conforming to IS : 164, on bituminous surface in white/yellow shade, including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete. New work (Two or more coats)
Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment).
Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 4.75 mm
Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).
Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure (the good earth shall be paid for separately).
Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.
Fine dressing of the ground.
Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).
Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.
Providing and stacking of Bottle palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big HDPE bags as per direction of the officer-in-charge.
Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.v
EXTERNAL SEWERAGE
Suppling, installation, testing & commissioning of STP/ETP of appopriate technology including civil work (except plant room ) tertiary treatment etc. for the building/campus
BOOM BARRIER (Electromechanical boom barrier with all accessories upto 6 meter length
RCC WATER TANK (UNDERGROUND SUMP)
RCC WATER TANK (OVERHEAD TANK WITH STAGING HEIGHT UPTO 20 METER)
Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.
Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.
Supplying, installation, testing & commissioning of intelligent analog addressable photothermal (Smoke) detector complete with mounting base complete as required.
Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.
Supplying, installation, testing & commissioning of fault isolator complete with base as required.
Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.
Supplying, installation, testing & commissioning of addressable fire control module complete as required.
Supplying, installation, testing & commissioning of addressable phone control module complete as required.
Supplying, installation, testing & commissioning of addressable manual call point complete as required.
Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.
Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.
Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.
Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.
Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.
Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.
Supplying, installation, testing & commissioning of digital audio amplifier 500 Watt, 25V rms operating at 240 Volt AC Supply complete as required.
Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.
Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.
Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm
Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required :Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainlesssteel shaft, mechanical seal conforming to IS 1520. Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class- 'F' insulation, conforming to IS-325. supply , Installation, testing and commissioning of fire Hydrant valve , bearing to IS:5290 marks, S.S. ,IS: 304 Grade, 63mm oblique instantaneous single out let, 75mm N.B. flanged inlet, brass spindles complete with PVC blank cap . G.I. chain etc. guard,foundation bolts etc.as required. supply , Installation, testing and commissioning of Branch pipe . S.S. short type with 63mm male instantaneous inlet, male threaded outlet fitted with 15mm, Bore nozzle,having IS: 903 with anti vibration pads. 2280 LPM 70 MTR HEAD
P/F weather proof standard fire hose cabinet locing arrangement with handle for housing hydrant valve two nos. 15 mts. Long fire hose pipes, branch pipes as reqd. as per drawing , including bracket for mounting accessories, painting (one coat primer and two coat of fire red color ) the cabinet shall be mounted on self standing mounted type painted M.S. angle iron frame as reqd. diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven supply , Installation, testing and commissioning of 25mm air release valve gunmetal, conforming to IS: 903:1993, having rubber ball and with 25mm BSP. THREADED male inlet including necessory accessories Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 2280 LPM 70 MTR HEAD
Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plasteredand with anti vibration pads. 180 lpm at 70 m Head
Supply, erection and testing of ISI marked M.S. pipes (class C) and specials etc. (as per IS:1239) for above ground laying for hydrants system includeing transportation of materials upto the worksite, cuttings the pipes to required length, edge preparation, welding, fixing / erection of pipes including specials i.e. bends, tees, reducers, flanges expansion joints wherever required, washers, nuts, bolts etc. in proper position including all supports as per layout. 200 mm dia (wall Thickness 6.3 mm)
Supply, erection and testing of ISI marked M.S. pipes (class C) and specials etc. (as per IS:1239) for above ground laying for hydrants system includeing transportation of materials upto the worksite, cuttings the pipes to required length, edge preparation, welding, fixing / erection of pipes including specials i.e. bends, tees, reducers, flanges expansion joints wherever required, washers, nuts, bolts etc. in proper position including all supports as per layout. 150 mm dia
Supply, erection and testing of ISI marked M.S. pipes (class C) and specials etc. (as per IS:1239) for above ground laying for hydrants system includeing transportation of materials upto the worksite, cuttings the pipes to required length, edge preparation, welding, fixing / erection of pipes including specials i.e. bends, tees, reducers, flanges expansion joints wherever required, washers, nuts, bolts etc. in proper position including all supports as per layout. 100 mm dia.
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required washers etc.as required : 200 mm dia
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required washers etc.as required : 100 mm dia
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required washers etc.as required : 150 mm dia
Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 200mm dia.
Installing ,testing and commissioning of butterfly valve , PN- 1.0,slim seal,standard lever operated type with required flanges, nuts ,bolts etc. complete. 200 mm dia.
Installing ,testing and commissioning of butterfly valve , PN- 1.0,slim seal,standard lever operated type with required flanges, nuts ,bolts etc. complete. 150 mm dia.
Installing ,testing and commissioning of butterfly valve , PN- 1.0,slim seal,standard lever operated type with required flanges, nuts ,bolts etc. complete. 100 mm dia.
Providing and fixining pressure gauge.
Providing and fixining 25 mm dia Ball Valve.
Providing and fixining air release valve.
Supplying & fixing air vessel made out of 250 mm dia,8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.
Supply, installation, testing & commissioning of flow switches with two no and two NC contacts with necessary nipply & other fittings, Flow switch shall be suitable for 150 dia.
Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :
Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150 mm dia
Supplying, Installing, hydraulic testing and commissioning of heavy grade MS Pipe confirming to IS:1239 part-1 with malleable specials confirming to IS:1239 part-II, such as Tee, elbows, check nuts, unions, flanges, nipple etc. Including cutting, fixing in/on wall/ on Floors, ceiling by using usitable supports such as MS channels, angles, flats, rods as required at site with anchor fastners, clamps, threaded rods, nuts, bolts, washers etc.. complete. Painting the exposed with one coadt of metal zinc chromate primer with two coats of synthetic enamal paint of approved colour/shade etc. complete. 80 mm dia
Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : 80 mm dia
Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.
supply , Installation, testing and commissioning of Branch pipe . S.S. short type with 63mm male instantaneous inlet, male threaded outlet fitted with 15mm, Bore nozzle,having IS: 903.
supply , Installation, testing and commissioning of Fire Hose,RRL hose jacketed with circular woven synthetic fibre,conforming to IS 636:88 63MM DIA.x 15mt. Long with SS 63mm 2 pair of male and female instantaneous coupling having IS :903 mark and duly S.S. wire wounded. The hose shall be rolled and hug to suitable M.S. support in the fire station.
Supply, erection and testing of ISI marked M.S. pipes (class C) and specials etc. (as per IS:1239) for above ground laying for hydrants system includeing transportation of materials upto the worksite, cuttings the pipes to required length, edge preparation, welding, fixing / erection of pipes including specials i.e. bends, tees, reducers, flanges expansion joints wherever required, washers, nuts, bolts etc. in proper position including all supports as per layout. 100 mm dia
Supply, erection and testing of ISI marked M.S. pipes (class C) and specials etc. (as per IS:1239) for above ground laying for hydrants system includeing transportation of materials upto the worksite, cuttings the pipes to required length, edge preparation, welding, fixing / erection of pipes including specials i.e. bends, tees, reducers, flanges expansion joints wherever required, washers, nuts, bolts etc. in proper position including all supports as per layout. 150 mm dia
Supply , Installation, testing and commissioning of Fire Hydrant valve , bearing to IS:5290 marks, S.S. ,IS: 304 Grade, 63mm oblique instantaneous single out let, 75mm N.B. flanged inlet, brass spindles complete with PVC blank cap . G.I. chain etc.
supply , Installation, testing and commissioning of Branch pipe . S.S. short type with 63mm male instantaneous inlet, male threaded outlet fitted with 15mm, Bore nozzle,having IS: 903
supply , Installation, testing and commissioning of Fire Hose,RRL hose jacketed with circular woven synthetic fibre,conforming to IS 636:88 63MM DIA.x 15mt. Long with SS 63mm 2 pair of male and female instantaneous coupling having IS :903 mark and duly S.S. wire wounded. The hose shall be rolled and hug to suitable M.S. support in the fire station.
supply , Installation, testing and commissioning of manual swing type Fire hose reel IS:884 comp. with heavy duty reel, 19mm dia. X 30 mtr. Long 2- ply polyster yarn braided / rubber braided pressure hose with heavy duty nylon on/off jet/ spray nozzle, 25mm isolating valve and all other necessory.
Providing/Fixing Fire man axe. Make.
CO2 type Fire exitinguisher ISI marked confirming to IS:15683 lates. Capacity 4.5 kg complete with delivery hose horn, squeeze grip release valve, locking arrangement, operating temperature -30°c to +55°c, supplied with body bearing IS 7285 mark and approved valve as per IS 3224. Co2 Gas as per IS:15222. externally painted with PO Red Shade No. 538 of IS 5, operation manual and floor stand or wall mount Bracket including accessories as required as per site condition. 4.5 kg.
Powder Fire exitinguisher (stored Pressure Type) (Powder pressurized with dry nitrogen gas at 15 bar) capacity 4kg duly ISI marked conforming to IS:15683:2006/latest, with IS 14609 ISI marked ABC powder complete with squeeze grip release valve, discharge pipe, locking arrangment, pressure gauge, operation maual, Body Hydrotested at 35 bar, operating temperature--30°c to +55°c, external epoxy powder coating with PO Red shade No. 538 of IS 5, and floor stand or wall mount Bracket including accessories as required as per site condition. 4.5 kg
Supplying, Installing, hydraulic testing and commissioning of heavy grade MS Pipe confirming to IS:1239 part-1 with malleable specials confirming to IS:1239 part-II, such as Tee, elbows, check nuts, unions, flanges, nipple etc. Including cutting, fixing in/on wall/ on Floors, ceiling by using usitable supports such as MS channels, angles, flats, rods as required at site with anchor fastners, clamps, threaded rods, nuts, bolts, washers etc.. complete. Painting the exposed with one coadt of metal zinc chromate primer with two coats of synthetic enamal paint of approved colour/shade etc. complete. 25 mm dia
Supplying, Installing, hydraulic testing and commissioning of heavy grade MS Pipe confirming to IS:1239 part-1 with malleable specials confirming to IS:1239 part-II, such as Tee, elbows, check nuts, unions, flanges, nipple etc. Including cutting, fixing in/on wall/ on Floors, ceiling by using usitable supports such as MS channels, angles, flats, rods as required at site with anchor fastners, clamps, threaded rods, nuts, bolts, washers etc.. complete. Painting the exposed with one coadt of metal zinc chromate primer with two coats of synthetic enamal paint of approved colour/shade etc. complete. 32 mm dia
Supplying, Installing, hydraulic testing and commissioning of heavy grade MS Pipe confirming to IS:1239 part-1 with malleable specials confirming to IS:1239 part-II, such as Tee, elbows, check nuts, unions, flanges, nipple etc. Including cutting, fixing in/on wall/ on Floors, ceiling by using usitable supports such as MS channels, angles, flats, rods as required at site with anchor fastners, clamps, threaded rods, nuts, bolts, washers etc.. complete. Painting the exposed with one coadt of metal zinc chromate primer with two coats of synthetic enamal paint of approved colour/shade etc. complete. 40 mm dia
Supplying, Installing, hydraulic testing and commissioning of heavy grade MS Pipe confirming to IS:1239 part-1 with malleable specials confirming to IS:1239 part-II, such as Tee, elbows, check nuts, unions, flanges, nipple etc. Including cutting, fixing in/on wall/ on Floors, ceiling by using usitable supports such as MS channels, angles, flats, rods as required at site with anchor fastners, clamps, threaded rods, nuts, bolts, washers etc.. complete. Painting the exposed with one coadt of metal zinc chromate primer with two coats of synthetic enamal paint of approved colour/shade etc. complete. 50 mm dia
Supplying, Installing, hydraulic testing and commissioning of heavy grade MS Pipe confirming to IS:1239 part-1 with malleable specials confirming to IS:1239 part-II, such as Tee, elbows, check nuts, unions, flanges, nipple etc. Including cutting, fixing in/on wall/ on Floors, ceiling by using usitable supports such as MS channels, angles, flats, rods as required at site with anchor fastners, clamps, threaded rods, nuts, bolts, washers etc.. complete. Painting the exposed with one coadt of metal zinc chromate primer with two coats of synthetic enamal paint of approved colour/shade etc. complete. 65 mm dia
Supplying, Installing, hydraulic testing and commissioning of heavy grade MS Pipe confirming to IS:1239 part-1 with malleable specials confirming to IS:1239 part-II, such as Tee, elbows, check nuts, unions, flanges, nipple etc. Including cutting, fixing in/on wall/ on Floors, ceiling by using usitable supports such as MS channels, angles, flats, rods as required at site with anchor fastners, clamps, threaded rods, nuts, bolts, washers etc.. complete. Painting the exposed with one coadt of metal zinc chromate primer with two coats of synthetic enamal paint of approved colour/shade etc. complete. 80 mm dia
Supplying, Installing, hydraulic testing and commissioning of heavy grade MS Pipe confirming to IS:1239 part-1 with malleable specials confirming to IS:1239 part-II, such as Tee, elbows, check nuts, unions, flanges, nipple etc. Including cutting, fixing in/on wall/ on Floors, ceiling by using usitable supports such as MS channels, angles, flats, rods as required at site with anchor fastners, clamps, threaded rods, nuts, bolts, washers etc.. complete. Painting the exposed with one coadt of metal zinc chromate primer with two coats of synthetic enamal paint of approved colour/shade etc. complete. 100 mm dia
Supply testing and commissioning of 15mm gunmetal/chrome quartzoid bulb, standard reponse sprinkler heads suitable for 65 deg. C K-80. Pendent-68 deg C.
Supply testing and commissioning of 15mm gunmetal/chrome quartzoid bulb, standard reponse sprinkler heads suitable for 65 deg. C K-80. Horizontal side wall sprinkler
Dial Type pressure guage for (0-16 kg/cm2) with necessary nipple & other fittings, mounting arrangements and with 15 mm ball valve.
Supply, Installtion, Testing & commissioning of 25mm ball valve with sight glass for sprinkler test line.
Supply, Installation, testing & commissioning of 50mm ball valve for sprinler drain line.
Supply, installation, testing & commissioning of flow switches with two no and two NC contacts with necessary nipply & other fittings, Flow switch shall be suitable for 100 dia.
Installing ,testing and commissioning of butterfly valve , PN- 1.0,slim seal,standard lever operated type with required flanges, nuts ,bolts etc. complete. 100 mm dia
Supply & Fixing of approved type rosette plates (Recessed Type, in two piece) for sprinklers below false ceiling area. Rosette shall be S.S. 304 as approved by engineers/ services consultants.
Stainless steel corrugatd flexible pipe(hose) for dropping sprinklers below false ceiling, pipe shall be UL Listed, 16 bar pressure rating and 25 mm dia with union/reducers collor, clamps etc. as required.(Braided) 1000 mm
Supply, Installtion, testing and commissioning of 25 mm diameter Forged Brass air release valve PN-1.6 Body.
Supply, Installation and commissioning of Annunciator Panel with 7 windows with point, zone & system status used with RS 485.
3 core 1.5 sq mm.
ELECTRICAL WORK Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 10 sq. mm + 2 X 6 sq. mm earth wire
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 16 sq. mm + 2 X 6 sq. mm earth wire
Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 mm
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV socket outlet
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. RJ45 socket cat 6 with shutter
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
Supplying and fixing brass batten/ angle holder including connection etc. as required. Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.
Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.
Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep
Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable
Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 18), Double door
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) For UPS Outgoing 8 way (4 + 24), Double door
Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 A, 16 KA,TPMCCB
Supplying and fixing 63Amp, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 300 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. Similar to Legrand or equivalent.
Supplying and fixing 40/63A rating, 415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Four poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Similar to Legrand DX3 AC MCBs or equivalent.
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
Supply of 8W Green Perform Sleek is a high performance low-height LED downlighter suited for requirements of any modern professional workspace. Robust PDC housing ensures long system. Narrow rim renders a pleasing aesthetic look. similar to Philips DN295B LED8S-6500 PSU WH or equivalent.
Supply of 22W Extruded aluminium batten available in 4ft run length with multiple lumen packages and suitable for surface, wall & conduit mounting (with accessories). etc. similar to Philips BN021C LED22S PSU CW GR or equivalent.
Supply of 12W Extruded aluminium batten available in 2ft run length with multiple lumen packages and suitable for surface, wall & conduit mounting (with accessories). etc. similar to Philips BN021C LED12S PSU CW GR or equivalent.
Supply of 36W Full Glow G6 comes with an all new deep drawn housing general illumination applications. Our carefully designed driver with ripple <5% ensures a flicker-free product designed for better health and wellbeing. Full Glow G6 also comes with a long service life and almost complete freedom from maintenance significantly reduce operating costs. similar to Philips RC380B LED36S-6500 G6 L60W60 PSU OD or equivalent.
Supply of 15W Slim profile surface mounted downlight with options of 700 to 2000 lumen. similar to Philips DN295B LED15S-6500 PSU WH or equivalent.
Supply Installation testing and commissioning of 400mm Sweep energy efficient copper wound wall mounted fan with swing and speed control option etc as required similar to Crompton Renesa or equivalent.
Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
Supply and fixing hexagonal Round G.P.fan box approved make made up of 1.0 mm thick ISI Marked G.P.sheet spot welded Four to Eight holes for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material, labour, T&P etc. required for proper completion of the work.
Supply of plastic body ventilation fan, 250mm sweep continously rated highly efficient similar to Crompton Cat. Efficio" or equivalent.
Supply of Pressure die cast housing LED bulkhead with IP66 protection and IK09 impact resistance suitable for surface and wall mounting applications. Similar to Philips Cat Ref. WT202W LED6S NW PSU S2 PC or equivalent.
Design, Manufacturing, Supply, Commissioning & Testing of Main LT Panel. The panel will be totally enclosed type with, free standing, floor mounted, indoor duty, dust & vermin proof, , front operated, electrical panel fabricated from 2 mm thick M.S. Sheet as per specifications & drawing laid in this document and will be complete with the main and auxiliary bus bars, multimeter, indication lamps, CT's, protection MCB, interconnection wiring, earth bus and will be powder coated finish with 50 micron thickness. The Main LT Panel shall use all breakers suitable for 415 V AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. All having following incomming and outgoing Air Circuit Breakers, FSU's as per the drawing and specification. Each incoming breaker will have microprocessor based releases and all outgoing breaker will have minimum electrostatic releases over 250A & thermal magnetic release below 250A. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 35 MVA. INCOMMER 1000Amp. 25KA FP With S/C, U/V, E/F Protection ACB-2 no. (From Transformer) 1000Amp. 25KA FP With S/C, U/V, E/F Protection ACB-2 no. (From DG Set) BUS COUPLER 1 Nos. 1250 Amp FP ACB BUSBARS 2 Nos. 1250 Amp FP busbars of aluminium alloy as per SLD. OUTGOING 500Amp. 25KA TP MCCB 2 No. (APFC Panel) 500Amp. 25KA FP ACB 4 No. (L+P Panel + Spare) 400Amp. 25KA FP MCCB 5 No. (HVAC+FF Panel+Spare) 100Amp. 25KA FP MCCB 4 No. (PL+STP+Spare)63Amp. 16KA FP MCCB 4 No. (Ex. Light+Spare) 160Amp. 16KA FP MCCB2 No. (UPS Panel+Spare) INSTRUMENTS 3 sets of multifunction meter with parameter current,voltage,KWH,KVAH,Power factor on incoming from transformers. 3 Sets of phase indicating lights (RYB) with protection fuses (one set for each incoming breaker). 3 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker).3 Sets auto trip indicating lamp . Building L+P Panel
Supply installing testing & commissioning of indoor type Distribution Panel (Distribution Panel) compartmentalised design, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required with following incomming & outgoing as per detail below. Incoming 500 Amp. 25 KA FP MCCB 1 No. BUSBARS 1 Nos. 250 Amp FP busbars of aluminium alloy as per SLD. Outgoing 32 Amp. 10KA FP MCB 12 No. 63 Amp. 10KA FP MCB 12 No.
Supply installing testing & commissioning of out door type street light feeder pillar (Distribution Panel) compartmentalised design, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required with following incomming & outgoing as per detail below. Incoming 63 Amp. 10 KA FP MCCB 1 No. Suitable contractor and timer for down & dusk 100 Amp. TPN Alu. Bus bar Outgoing 32 Amp. 10KA FP MCB 2 No. 32 Amp. 10KA DP MCB 2 No. (GR) 25 Amp. 10KA FP MCB 10 No.
Supply of Power Cables,Solid Aluminum conductor up to 10 sqmm balance stranded conductor,XLPE Insulated,cores laid up, PVC tape nersheathed,unarmoured/Armour(Aluminium wire for single core up to 70 sqmm balance Aluminium strip, Glavanised wire for cables upto 2x16 sqmm, 3x10 sqmm & balance all galvanised steel strip),extruded PVC Type ST2 sheathed,650/1100V grade as per IS 7098(Part 1) 1988 2CX6Sq.mm Cable
Supply of Power Cables,Solid Aluminum conductor up to 10 sqmm balance stranded conductor,XLPE Insulated,cores laid up, PVC tape nersheathed,unarmoured/Armour(Aluminium wire for single core up to 70 sqmm balance Aluminium strip, Glavanised wire for cables upto 2x16 sqmm, 3x10 sqmm & balance all galvanised steel strip),extruded PVC Type ST2 sheathed,650/1100V grade as per IS 7098(Part 1) 1988 4CX6Sq.mm Cable
Supply of Power Cables,Solid Aluminum conductor up to 10 sqmm balance stranded conductor,XLPE Insulated,cores laid up, PVC tape nersheathed,unarmoured/Armour(Aluminium wire for single core up to 70 sqmm balance Aluminium strip, Glavanised wire for cables upto 2x16 sqmm, 3x10 sqmm & balance all galvanised steel strip),extruded PVC Type ST2 sheathed,650/1100V grade as per IS 7098(Part 1) 1988 4CX16Sq.mm Cable
Supply of Power Cables,Solid Aluminum conductor up to 10 sqmm balance stranded conductor,XLPE Insulated,cores laid up, PVC tape nersheathed,unarmoured/Armour(Aluminium wire for single core up to 70 sqmm balance Aluminium strip, Glavanised wire for cables upto 2x16 sqmm, 3x10 sqmm & balance all galvanised steel strip),extruded PVC Type ST2 sheathed,650/1100V grade as per IS 7098(Part 1) 1988 3.5CX35Sq.mm Cable
Supply of Power Cables,Solid Aluminum conductor up to 10 sqmm balance stranded conductor,XLPE Insulated,cores laid up, PVC tape nersheathed,unarmoured/Armour(Aluminium wire for single core up to 70 sqmm balance Aluminium strip, Glavanised wire for cables upto 2x16 sqmm, 3x10 sqmm & balance all galvanised steel strip),extruded PVC Type ST2 sheathed,650/1100V grade as per IS 7098(Part 1) 1988 3.5CX50Sq.mm Cable
Supply of Power Cables,Solid Aluminum conductor up to 10 sqmm balance stranded conductor,XLPE Insulated,cores laid up, PVC tape nersheathed,unarmoured/Armour(Aluminium wire for single core up to 70 sqmm balance Aluminium strip, Glavanised wire for cables upto 2x16 sqmm, 3x10 sqmm & balance all galvanised steel strip),extruded PVC Type ST2 sheathed,650/1100V grade as per IS 7098(Part 1) 1988 3.5CX95Sq.mm Cable
Supply of Power Cables,Solid Aluminum conductor up to 10 sqmm balance stranded conductor,XLPE Insulated,cores laid up, PVC tape nersheathed,unarmoured/Armour(Aluminium wire for single core up to 70 sqmm balance Aluminium strip, Glavanised wire for cables upto 2x16 sqmm, 3x10 sqmm & balance all galvanised steel strip),extruded PVC Type ST2 sheathed,650/1100V grade as per IS 7098(Part 1) 1988 3.5CX150Sq.mm Cable
Supply of Power Cables,Solid Aluminum conductor up to 10 sqmm balance stranded conductor,XLPE Insulated,cores laid up, PVC tape nersheathed,unarmoured/Armour(Aluminium wire for single core up to 70 sqmm balance Aluminium strip, Glavanised wire for cables upto 2x16 sqmm, 3x10 sqmm & balance all galvanised steel strip),extruded PVC Type ST2 sheathed,650/1100V grade as per IS 7098(Part 1) 1988 3.5CX240Sq.mm Cable
Supply of Power Cables,Solid Aluminum conductor up to 10 sqmm balance stranded conductor,XLPE Insulated,cores laid up, PVC tape nersheathed,unarmoured/Armour(Aluminium wire for single core up to 70 sqmm balance Aluminium strip, Glavanised wire for cables upto 2x16 sqmm, 3x10 sqmm & balance all galvanised steel strip),extruded PVC Type ST2 sheathed,650/1100V grade as per IS 7098(Part 1) 1988 3.5CX300Sq.mm Cable
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 6 sq. mm (25mm)
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 10 sq. mm (25mm) / 4 X 6 sq. mm (25mm)
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 16 sq. mm (28mm)
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 50 sq. mm (35mm)
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 95 sq. mm (45mm)
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 150 sq. mm (50mm)
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 240 sq. mm (62mm)
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5CX300Sq.mm Cable
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 35 sq. mm and upto 95 sq. mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 95 sq. mm and upto 185 sq. mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 185 sq. mm and upto 400 sq. mm
Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm
Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 35 sq. mm and upto 95 sq. mm
Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 95 sq. mm and upto 185 sq. mm
Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 185 sq. mm and upto 400 sq. mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35 sq. mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 185 sq. mm and upto 400 sq. mm
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.
Supply & fixing of 7 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 130mm and base plate 12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect.
Supply and fixing of LED Street light Fitting SmartBright Essential is a street lighting luminaire with PDC housing and street light optics to ensure uniform distribution. similar to Philips BRP032 LED60 CW SLR GR PSU or equivalent.
Supply Installation Testing & Commissioning of E-Topp LED post top lantern with spun aluminium canopy and die cast aluminium spiget offers symettric light distribution with clear acrylic diffuser. similar to Surya SLE PT 40W ETPP or equivalent.
Supply Installation Testing and Commissioning of Decorative Mild steel galvanized tubular Pole having different prole with cast alumn. embellishment E3. Pole has a service window and xed base plate at bottom prole. Pole is primer coated and PU painted. Similar to Twinkle cat ref. Twinkle Lite-SCRLT-E3-409030 or equivalent.
Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 300mm Dia
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 200mm Dia
Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness
Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness
Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 600 mm width X 50 mm depth X 1.6 mm thickness
S/F of cable root marker
S/F of Shock treatment chart
S/F of LT/HT Danger Notice Plate
H. T. SYSTEM 11 KV DOUBLE POLE STRUCTURE Supply, erection, testing and commissioning of 2 pole structure for providing 1 No. 11KV,200A GOS in accordance with IE rules, & local authority specification and drawings and comprising of the following. a. 2 Nos. 11 mtr. long MS STEEL poles complete with, pole excavation, MS STEEL foundation, and back filling complete MS steel channel/angle iron etc. b. 1 Set of cross arms, branching, clamps and painting complete with GI nut, bolts & washers as required (for GO & DO), LA connection. c .1 set 11KV Insulator complete with spindles & hardware complete as required. d .1 No. 11KV 400A TP Gang operated Air break switches complete with 25mm dia GI pipe operating machanism, handle & locking arrangement. e. 1 set of 3 nos.11KV single pole drop out fuse complete with barrel fuses, and mounting arrangement.f. 1 set (3 nos.) 11KV lightning arrestor and connecting to all phases. g. 1 No. 150 mm dia GI pipe class 'B' (for XLPE cable protection) as required. h. 2 Set 50mm dia 3m long GI pipe earting with 25 x 6 mm GI earth strip complete as required (for GO & DO & LA) i 1 nos. 11KV HT danger boards and 2 set of anticlimbing devices. 33 KV Double Pole Structure Unitised Sub Station (11KV / 415 V) 500 KVA With 1 I/C & 2 O/G (With Natural cooling)
Outdoor type package substation with facility for internal lighting, earthing, padlocks etc. Connection between RMU & transformer will be by 1 no. 3Cx95 sq.mm. XLPE cable/Busbar and connections from transformer to LT ACB will be by busbar connections. Unitised Sub Station will have the following equipment H.T SWITCHGEAR Three way, 11KV 630Amp. 25KA for 1 sec. SF6 insulated Non-Extensible compact switchgear consisting of two nos. of fixed load break switch and one no. fixed vacuum circuit breaker in SF6 insulated stainless steel enclosure with self powered series trip microprocessor base numerical over current & earth fault relay (IDMTL+inst.) for protection. RMU NON Extensible (2 isolators, 1 VCB with CU Busbar Function type- 3 position disconnector and earthing switch equipped with separate drive unit. 1. Operation of LBS manual 2. Cable switch rating 11KV,630A, 25kA/1sec. 3. Cable bushing rating 630A. 4. Cable cover- As per our standard. 5. Fixed type capacitive voltage indication provided. 6. ON/OFF/Earth indication on the front mimic of the panel. 7. Bottom cable termination-suitable upto 1 no. 3C X 300sq.mm 8. Cable entry bottom, front. 9. Fault passage indicator (FPI)-E/F FUNCTION Type- 3 position disconnector and earth switch equipped with seperate drive unit. T2 equipped with over current time release for transformer protection. 1. VCB 11KV, 630A, 25kA/1sec.2. Operation of breaker-Manual 3. Self powered electronic numerical protection relay providing over current and earth fault protection. 4. Tape wound protection current transformer 5. Capacitive voltage indication fixed type. 6. ON, OFF, EARTH indication on the frount mimic of the panel 7. Cable box for termination of cable.8. Cable cover stand. 9. Emergency trip push button. 10. Shunt trip coil. 11. Operation counter. 12. Ammeter. RMU accessories- Manual Operating handle-1nos. Standard manometer for SF6 GAS pressure indication. Right angled cable boots suitable for 1 RMU X 3C X 300sq.mm Transformer (Manufactured as per IS 1180 Level-II) Type- ONAN, Hermatically sealed corrugated tack. 1. Ratio- 11KV/433V 2. Capacity 500KVA 3. Vector group DYn11 4. off load tappings +5% to -10% in steps of 2.5% 5. Winding- Double wound copper6. Class of insulation-A 7. Ambient temp. 40 degree C 8. Temp. rise in oil over ambient- 40 deg. C 9. Temp. rise in winding over ambient- 45 deg. C Transformer Accessories Oil Temperature indicator LT Busbar- Main bus bar are aluminium however copper flexible arer provided between Transformer and LT incommer connection alongwith main busbar 1. Voltage rating 433V 1. Voltage rating 433V 2. Current rating- 1000 Amp.L.T Panel Incoming 1000Amp. 25KA, 4P EDO ACB O/L, S/C, E/F protection LSIG, LCD Display having specs as per attached annexture ON, OFF TRIP lamp. R/Y/B indicating lamp. Multifunction meter CT-1000/5A, CL1.0, 10VA Earthing- Internal earthing connection by using 50X6 Aluminium strips. ENCLOSURE for PSS Rated temperature enclosure class should be K10 Outdoor type 2mm thick galvenised enclosure shall have IP54 degree of protection for HT & LT switchgear compartment & IP34 degree of protection for transformer compartment. The enclosure exterior shall be powder coated with PP based paint. HT & LT compartment will be provided with the door and pad locking arrengement. Transformer compartment will be provided with cover. The compartment illumination lamp with door operated switch shall be provided for lifting arrengement shall be provided with PSS. Base frame of PSS shall be 4mm thick Earthing- Internal earthing connection by using 50X6 Aluminium strips. HT Panel, (Main)
Supply of 11KV grade 3core Brand Stranded Compact Circular Aluminium Conductor, Conductor Screen With Extruded Semi Conducting Compound, XLPE Insulated, Insulation Screening with extruded Semi Conducting Compound in combination with Copper Tape, cores laid up, innersheath of PVC tape, galvanised flat steel strip armoured and overall PVC Sheathed Cable conforming to IS 7098 / (PART-II) 1985 with latest amendments. 240sq.mm 3 core
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 120 sq. mm and upto 400 sq. mm
Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 120 sq. mm and upto 400 sq. mm
Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 240sq.mm 3 core/300sq.mm 3 core
Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 240sq.mm 3 core/300sq.mm 3 core
Supply , Installation, Testing & Commissioning of 03 phase volts 50 cycle per second 1500 RPM air cooled, deisel generating set complete with silent type DG canopy & limiting sound level to 75 dB (A) over a distance of one meter with engine, alternator air cooled. The engine shall be complete with flywheel to suit flexible coupling with guard, air cleaner, fuel pump, fuel day tank, variable speed governor, fuel filter, lube oil filter, battery charging generator, voltage regulator, 24 volt charged voltage regulator, capacity and instrument panel comparing switch with key, space heater, lube oil temperature gauge, lube oil pressure gauge, water temperature gauge, battery charging ammeter, safety control for low lube oil pressure and high temperature tripping. The canopy temperature shall not exceed 7 degree above the alternator shall be brushless type excited and self regulated continously rated as follows, 3 phase 415 volts 50cycles, 4 wire system and shall be provided with static excitation unit, alternator insulation shall be class "H" or better to withstand tropical conditions and shall generally comply with relevant IS and present by-laws under average conditions the voltage regulation shall be within ± 1.5%. The overload capacity shall not be less than 110% for one hour in every 12 hours. The set shall be mounted on a common bed plate with antivibration mounting and alternator shall be suitable for LT AL XLPE cables connection and alternator shall be suitably modified and similarly provision shall be made in the canopy to take out AL XLPE cables As per CPCB-IV 500 KVA
Supply installing testing & commissioning of out door type street light feeder pillar (Distribution Panel) compartmentalised design, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required with following incomming & outgoing as per detail below.Incoming 160 Amp. 10 KA FP MCCB 2 No. (Electrical Interlock) BUS COUPLER 1 Nos.160 Amp FP ACB BUSBARS 2 Nos. 200 Amp FP busbars of aluminium alloy as per SLD. Outgoing 100 Amp. 16KA FP MCCB 4 No.
Supply, installation, testing & commissioing of 60 KVA UPS in paralleling mode at 0.99 input power factor with SNMP card, compatible for BMS connectivity on backnet/MODBUS, inbuilt / external isolation transformer as per specification given in the document with following broad features. Including required panel and cables. THD(i) shall be less than 3% in the entire loading range. Input power factor shall be more than 0.95. from 25% to 100% load. UPS shall carry design output at 40 deg. Shall have soft start and hold of for incoming supply. Invertor capability to supply 150% load for 5 sec. Three Phase Input and Three Phase Output. ( Input - 340V - 470V, Three Phase, 4 wire. / Output - 400-415 Volt, Three Phase, 4 Wire.) Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells. Battery shall be external type with rack and suitable for 30 minute backup on 100% load. UPS shall be compatible for minimum 2 nos unit in parallel operation. (Synchronize). Parallel operation kit shall be supplied with UPS. UPS described as above
Design, manufacturing, Supply, installation, testing and commissioning of outdoor type 500 KVA servo controlled Automatic Voltage Stabilizer, self-lubricating Carbon Roller Assemblies suitable for unbalanced load with digital micro controlled with Copper Winding, oil cooled type with bye pass arrangement of power drawing, cutoff panel cable termination box etc and It also includes testing of Transformer oil and subsequent filtering of oil at site before commissioning rest as per technical specification sheet
DG set, AMF panel bus ducting cables from DG sets to esential panel , DG set enclosure room sound insulation/ventilation /smoke exhaust as required earthing of DG set system control cabling fuel tank piping DG set exhaust piping exhaust chimney as per CPCB norms civil works connected with DG set including foundations required.
OUTDOOR UNITS: Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5. (Design should be got approval before execution from engineer in charge) . 36 HP
OUTDOOR UNITS: Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5. (Design should be got approval before execution from engineer in charge) . 34 HP
OUTDOOR UNITS: Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5. (Design should be got approval before execution from engineer in charge) . 24 HP
OUTDOOR UNITS: Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5. (Design should be got approval before execution from engineer in charge) . 22 HP
OUTDOOR UNITS: Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5. (Design should be got approval before execution from engineer in charge) . 18 HP
OUTDOOR UNITS: Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5. (Design should be got approval before execution from engineer in charge) . 14 HP
OUTDOOR UNITS: Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5. (Design should be got approval before execution from engineer in charge) . 8 HP
4-WAY FLOW CASSETTE: Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. fresh air provision compatible for Remote Operation System . 2.0 TR
4-WAY FLOW CASSETTE: Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. fresh air provision compatible for Remote Operation System . 2.8 TR
4-WAY FLOW CASSETTE: Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. fresh air provision compatible for Remote Operation System . 3.2 TR
4-WAY FLOW CASSETTE: Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. fresh air provision compatible for Remote Operation System . 4.0 TR
HI-WALL UNITS Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature 1.0 TR
HI-WALL UNITS Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature 1.65 TR
Supply,Installation,testing and commissioning of corded /Cordless remote controls as per drawing and specifications
Supply,Installation,testing and commissioning of centralised remote controlers as per drawing and specifications
Supply,Installation,Testing & Commissioning of Y Joints-Indoors
Supply,Installation,Testing & Commissioning of Y Joints-outdoors
REFRIGERANT PIPE: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given belo 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation
REFRIGERANT PIPE: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given belo 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation
REFRIGERANT PIPE: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given belo 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation
REFRIGERANT PIPE: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given belo 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation
REFRIGERANT PIPE: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given belo 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation
REFRIGERANT PIPE: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given belo 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation
REFRIGERANT PIPE: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given belo 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation
REFRIGERANT PIPE: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given belo 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation
REFRIGERANT PIPE: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given belo 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation
REFRIGERANT PIPE: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given belo 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation
REFRIGERANT PIPE: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given belo 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation
REFRIGERANT PIPE: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given belo 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation
Supply & fixing of control cum transmission wiring of 2 C X 1.5 Sq. mm Copper conductor cable alongwith conduite for looping between indoor & outdoor VRF system.
Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of following size. 3C x 2.5 sq.mm
Drain Piping : Supply,installation,testing and commissioning of of CPVC pipes having thermal stability for condesate water including wrapping of 9mm thick class 0 nitrile rubber insulation with suitable adhesive with all CPVC plain and brass threaded fittings including the pipes with clamps 1metre spacing.This including jointing of pipes with one step CPVC solvent cement and testing of joints complete as per drg and specifications 50 mm dia.
Drain Piping : Supply,installation,testing and commissioning of of CPVC pipes having thermal stability for condesate water including wrapping of 9mm thick class 0 nitrile rubber insulation with suitable adhesive with all CPVC plain and brass threaded fittings including the pipes with clamps 1metre spacing.This including jointing of pipes with one step CPVC solvent cement and testing of joints complete as per drg and specifications 40 mm dia.
Drain Piping : Supply,installation,testing and commissioning of of CPVC pipes having thermal stability for condesate water including wrapping of 9mm thick class 0 nitrile rubber insulation with suitable adhesive with all CPVC plain and brass threaded fittings including the pipes with clamps 1metre spacing.This including jointing of pipes with one step CPVC solvent cement and testing of joints complete as per drg and specifications 32mm dia.
Drain Piping : Supply,installation,testing and commissioning of of CPVC pipes having thermal stability for condesate water including wrapping of 9mm thick class 0 nitrile rubber insulation with suitable adhesive with all CPVC plain and brass threaded fittings including the pipes with clamps 1metre spacing.This including jointing of pipes with one step CPVC solvent cement and testing of joints complete as per drg and specifications 25 mm dia.
Axial Fan for "Exhaust Air (Emergency)" Supply installation, testing and commissioning of single piece long casing (Motor should completely be accommodated inside the fan casing) Vane Axial Fan (multi piece casing are not acceptable) in GSS/MS with powder coated, Al impeller with adjustable blade angles (Manually Adjustable at Site), bird screen ,gravity louvers, fire retardent flexible connection, necessary nut bolts and directly coupled TEFC Sq.cage induction motor (IE2) H Class insulation for Smoke Exhaust) suitable for 415V±10%, 50 Hz. 3 phase electric supply complete with required hardware etc. All offered fans pitch angle shall be AMCA Certified & Listed on AMCA website (Interpolation of pitch angle shall not be acceptable) and Fan Efficiency Grade ( Min FEG 71, lesser is not acceptable).Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm & Dia 1600 – 5 mm. All fans after assembly shall be dynamically trim-balanced to ISO1940 and AMCA 204/3 - G2.5 quality grade. Fan Casing should be provided with Special Designed Integral Straightening Vanes (Vanes should be integral part of casing, it should not be provided separately as an accessory) to reduced turbulence provide high performance & low noise level. Fans for emergency application Tube axial are to be used. Sound level for emergency operation it should not exceed 88 Db(A)@ 3 meter (Room condition).Incase of not achieving sound , attenutor has to be added. Outlet velocity of the fans should not exceed 18 m/s for emergency application. Smoke and heat exhaust fans should be tested and certified for 250 Deg C for 2 hour in accordance to standard 'BSEN12101-3:2015 from TUV SUD PSB Singapore or equivalent internationally recognized fire laboratory. Emergency Operation 7000 CFM @35 static pressure
Axial Fan for "Exhaust Air (Normal)" Supply installation, testing and commissioning of single piece long casing (Motor should completely be accommodated inside the fan casing) Vane Axial Fan (multi piece casing are not acceptable) in GSS/MS with powder coated, Al impeller with adjustable blade angles (Manually Adjustable at Site), bird screen ,gravity louvers, fire retardent flexible connection, necessary nut bolts and directly coupled TEFC Sq.cage induction motor (IE2) (H Class insulation for Basement Exhaust) suitable for 415V±10%, 50 Hz. 3 phase electric supply complete with required hardware etc. All offered fans pitch angle shall be AMCA Certified & Listed on AMCA website (Interpolation of pitch angle shall not be acceptable) and Fan Efficiency Grade (Min FEG 71, lesser is not acceptable).Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm & Dia 1600 – 5 mm. All fans after assembly shall be dynamically trim-balanced to ISO1940 and AMCA 204/3 - G2.5 quality grade. Fan Casing should be provided with Special Designed Integral Straightening Vanes (Vanes should be integral part of casing, it should not be provided separately as an accessory) to reduced turbulence provide high performance & low noise level. Fans for normal application Vane axial are to be used. Sound level for normal application fans should not exceed 78 DB(A)@ 3 meter (Room Condition). Incase of not achieving sound , attenutor has to be added. Outlet velocity of the fans should not exceed 15 m/s for normal application. Smoke and heat exhaust fans should be tested and certified for 250 Deg C for 2 hour in accordance to standard 'BSEN12101-3:2015 from TUV SUD PSB Singapore or equivalent internationally recognized fire laboratory.Normal Operation15000 CFM @ 30static pressure
Staircase and Lifts Pressurisation Fan - Supply, installation, testing and commissioning of floor mounted / ceiling hang Axial flow type supply air fan for Lift well, lobby & stairwell pressurization of following capacity with powder coated GSS/M.S. casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller directly driven by TEFC induction motor (efficiency 1) and 'F' class insulation suitable for 3 Phase, 50 Hz, 415±10% Volt, TP isolator with M.S enclosure box complete as required and as per specifications. Fans should be statically & dynamically balanced.The fan static pressure shall be 20 mm WC static. as per site condition 10000 CFM (for staircase)
Staircase and Lifts Pressurisation Fan - Supply, installation, testing and commissioning of floor mounted / ceiling hang Axial flow type supply air fan for Lift well, lobby & stairwell pressurization of following capacity with powder coated GSS/M.S. casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller directly driven by TEFC induction motor (efficiency 1) and 'F' class insulation suitable for 3 Phase, 50 Hz, 415±10% Volt, TP isolator with M.S enclosure box complete as required and as per specifications. Fans should be statically & dynamically balanced.The fan static pressure shall be 20 mm WC static. as per site condition 3500 CFM (for lift)
DUCTING , GRILLS, DIFFUSER AND DIFFUSER (VENTILATION) Rectangular ductwork Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 24 Gauge (thickness 0.63mm sheet)
DUCTING , GRILLS, DIFFUSER AND DIFFUSER (VENTILATION) Rectangular ductwork Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 22 Guage (thickness 0.80mm sheet)
Duct Insulation Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19mm
Supply,installation,testing and commissioning of flexible duct connections constructed of fire resistance flexible double canvas sleeve as per the drawings and specifications.
Supply , Erection of Fresh air louver with extruded aluminium grill with SS wire mesh and GI volume control damper with 20 micron filters
Supply, installation, testing and commissioning of anodised aluminium Fresh air/Exhaust air louvers with bird screen as per specifications and drawings.
Supply and Installation of GI backdraft dampers as per UL 555 Standard,
Supply,installation testing and commissioning of AIR CURTAIN of following size as per approved make . 1200 mm long (High flow type)
Supply,installation testing and commissioning of AIR CURTAIN of following size as per approved make . 1500 mm long (High flow type)
Supply,installation,testing and commissioning of Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (a) 3 core 2.5Sq. mm
Supply,installation,testing and commissioning of Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (a-1) 3 core 4 Sq. mm
Supply,installation,testing and commissioning of Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (b) 3 core 6 Sq. mm
Supply,installation,testing and commissioning of Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (c) 3 core 10 Sq. mm
Supply,installation,testing and commissioning of Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (d) 3 core 16 Sq. mm
Supply,installation,testing and commissioning of Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (E) 3 core 25 Sq. mm
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 3 1/2 core 150 Sq. mm
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 3 1/2 core 240 Sq. mm
Providing and fixing approved make Perforated C type cable tray. Made from sheet steel. The cable tray should be single or double bended as per required and as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erection with necessary support( included) as per Specification and as per instruction of engineer in charge.. 100 X 50 X 1.6 mm Thick
Providing and fixing approved make Perforated C type cable tray. Made from sheet steel. The cable tray should be single or double bended as per required and as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erection with necessary support( included) as per Specification and as per instruction of engineer in charge.. 150 X 50 X 1.6 mm Thick
Providing and fixing approved make Perforated C type cable tray. Made from sheet steel. The cable tray should be single or double bended as per required and as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erection with necessary support( included) as per Specification and as per instruction of engineer in charge.. 300 X 50 X 2.0 mm Thick
Earthing : Supply,installation,testing and commissioning of following double earthing continuity conductor of Cu from Panels to respective equipment on surface or recess as per drawings and specifications. 25 mm X 5 mm strip
Earthing : Supply,installation,testing and commissioning of following double earthing continuity conductor of Cu from Panels to respective equipment on surface or recess as per drawings and specifications. 8 SWG wire
Earthing : Supply,installation,testing and commissioning of following double earthing continuity conductor of Cu from Panels to respective equipment on surface or recess as per drawings and specifications. 50sq mm ( for earthing)
CCTV Work. Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 Run of Cable
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm
S/I/T/C of 24 port category 6e SL Series patch Panel Make Dlink/Amp with active and passive components,punching, complete in all respect
Supplying, installing, testing and commissioning of I/O(Information outlet ) for CAT6 Cable termination
Supplying, installing, testing and commissioning of 6 U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos of hardware pkts.
Supplying, installing, testing and commissioning of 42 U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos of hardware pkts.
Supplying, installing, testing and commissioning of 24 10/100/1000BASE-T PoE-plus
SITC of 2 MP IR Fixed Dome Network Camera -1/2.7″ Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, 0.002 Lux at F1.4, 0 Lux with IR on, ICR, ONVIF (PROFILE S, PROFILE G, PROFILE T), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 256 GB (SD card not included), IP67, Edge Analytics- Line crossing detection, Intrusion detection, Motion detection, Video tampering, UL, CE, FCC certified.
SITC of 2 MP IR Fixed Bullet Network Camera -1/2.7″ Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, 0.002 Lux at F1.4, 0 Lux with IR on, ICR, ONVIF (PROFILE S, PROFILE G, PROFILE T), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 256 GB (SD card not included), IP67, Edge Analytics- Line crossing detection, Intrusion detection, Motion detection, Video tampering, UL, CE, FCC certified.
SITC of 2 MP IR Fixed Dome Network Camera for Lift -1/2.7″ Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, 0.002 Lux at F1.4, 0 Lux with IR on, ICR, ONVIF (PROFILE S, PROFILE G, PROFILE T), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 256 GB (SD card not included), IP67, Edge Analytics- Line crossing detection, Intrusion detection, Motion detection, Video tampering, UL, CE, FCC certified.
SITC of 64 channel Network Video StoragE NVR suitabe to access data from any remote location including backup drive for 30days.
SITC of 64 channel Network Video StoragE NVR suitabe to access data from any remote location including backup drive for 30days.
Supplying, installing, testing and commissioning of HDMI to HDMI Cable.
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
Supply installing testing & commissioning of out door type junction box, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required suitable for mounting of 2 nos. 5/6Amp Switch & Sockets.
Supplying,Installation ,Testing & Commissioning of Passenger Elevators With power operated centre opening door and AC variable voltage and variable frequency Drive at a speed of 1.5m/sec. with reverse opening type MRL lift. 10 Passenger For B1+B2+G+5 Floors
Supplying,Installation ,Testing & Commissioning of Passenger Elevators With power operated centre opening door and AC variable voltage and variable frequency Drive at a speed of 1.5m/sec. with single side opening type MRL lift. 13 Passenger For B1+B2+G+5 Floors
Supplying,Installation ,Testing & Commissioning of Passenger Elevators With power operated centre opening door and AC variable voltage and variable frequency Drive at a speed of 1.5m/sec. with single side opening type MRL lift. 8 Passenger For G+4 Floors
EPABX SYSTEM Supply of Server based IP EPABX, Non blocking, Servers ( 19” Rack Mountable in load sharing Architecture accommodating to all IP and analog users in standard 19” Supply of IP User Licences ( 25 Nos. Users) Supply of Analog Extension cards with ports ( 150 Nos. User) Supply of E1 ISDN PRI ( 30 Channels) Card ( 2 Nos) Supply of CO Trunk Cards- ( 8 Lines) Supply of 2-Port IP Phones minimum 3X1.5 Inches screen with 2 way speaker as per technical specifications. 25 Supply of management platform inclusive of management software as per technical specifications 1 Supply of IP Based Operator Console 1 Supply of call billing software as per specifications 1
Supply installation testing and commissioning of Analog telephone handset with Caller ID etc as required.
Supply of PC A4 size printer scanner and photo copier alongwith dedicated UPS for PC and assesories as required.
S/f of I/O Boxes Krone connectors ,with connection etc. 50 Pair
S/f of I/O Boxes Krone connectors ,with connection etc. 100 Pair
S/f of I/O Boxes Krone connectors ,with connection etc. 300 Pair
Wiring of Jelly Filled telephone Cable in existing pipe for system with connection. 50 Pair
Wiring of Jelly Filled telephone Cable in existing pipe for system with connection. 100 Pair
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 Run of Cable
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm
S/I/T/C of 24 port category 6e SL Series patch Panel Make Dlink/Amp with active and passive components,punching, complete in all respect
Supplying, installing, testing and commissioning of I/O(Information outlet ) for CAT6 Cable termination
Supplying, installing, testing and commissioning of 24 10/100/1000BASE-T PoE-plus
SITC of 2m long Cat-6 patch cord as required
DATA / NETWORKING SYSTEM S/F of Surface mount box with I/O Cat 6 and UTP jack D-Link complete in all respect Make Dlink/Amp
S/I of Patch cord CAT6 UTP Make Dlink/Amp
S/I/T/C of 24 port category 6e SL Series patch Panel Make Dlink/Amp with active and passive components,punching, complete in all respect
Supplying, installing, testing and commissioning of 24 10/100/1000BASE-T PoE-plus
Supplying, installing, testing and commissioning of 6 U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos of hardware pkts.
Supplying, installing, testing and commissioning of 42 U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos of hardware pkts.
Mapping of Network Nodes & LAN Diagram
SITC of WIFI Modem suitable to cover atleast 25m distance having compatibility to connect atleast 40-50 devices without any distortion in signal etc as required.
Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conformington MNRE specifications as amended, consisting of Mono / Poly Crystalline silicon solar cells, netmetering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:-a)Solar Photovoltaic Module of capacity 330Wp or above, manufactured in India, conforming to IS14286/IEC61215, IS/IEC61730-Part-1, IS/IEC61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10years and 80% at the end of 25 years. b)Power Conditioning Unit (PCU) of 350-800VDC Input voltage range and 400VAC, three phase, 4wire, 50Hz+/-2.5Hz, out put voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0to50degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency.c) Data Monitoring System complete with accessories. d) Fixing of Array junction box & Main junction box with IP65 protection and termination arrangement for in coming and outgoing cable alongwith glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnectionsby supplying&fixingrequiredsizeXLPEinsulatedcopperconductor1.1kVgradearmouredpowerandcontrolcablesbetweensolarmodules,mainpowercabletogridsupplyPCUunitalongwithsupplying&fixingofnecessarychannel/conduitlugsandotheraccessoriesetc.asrequired. 1kWp
Audio System Supply, Installation, Testing & Commissioning Full range Ceiling loudspeaker with 1x 2.25"transducer, Frequency response: 95Hz to 16kHz; Power handling capacity: 16 Watt; Nominal dispersion: 145° Conical; Sensitivity: 86 dB SPL and Max SPL: 98 dB SPL; Nominal Impedance: 16 Ohms or 70/100V; Integral multi-tap Transformer with tap settings: 2/4/8/16 W @70V/100V. Installation: Indoor complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of Dual-channel proffessional Class-D low impedance power amplifier; Should have power output of 2x 50W @4Ω and 2x 25W @8Ω or better; Frequency response: 40Hz- 20kHz or better; Should have Input Impedance: 20 kΩ or better; Total harmonic distortion (THD): ≤0.3% or better; Should have Channel seperation (Crosstalk): ≤-60 dBV or better; Dynamic range: 88dB or better complete with standard accessories as required.
Supply, Installation testing & commissioning of A-weighted 32-bit fixed/floating-point DSP + ARM Cortex-A8; Frequency Response : 18 Hz – 20 kHz; 456 MHz Signal processor; Dynamic Range : > 115 dB; Input channel: 4-AEC analog (balanced, mic/line level); Output channel : 4-AEC analog (balanced, line level), 4 or more Digital output on RJ-45; Sample Rate : 48 KHz; THD+N : 0.003%; Channel seperartion(crosstalk): <-105 dB; Dante Expansion: 16X16, primary/secondary; USB Stereo in/out; VOIP (RJ-45 port); PSTN(RJ-11 port); Display: 256 x 64 OLED with rotary encoder; Ethernet (RJ-45); 100Mb network control complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of Ceiling Microphone tile with Min of 28 or more Pre-polarized condenser capsule or higher, Should have TruVoice Lift technology or better, Sound pressure level : max. 104 dB SPL, Dynamic range 93 dB(A) or better, should have Adaptive beamforming technology or better, should support Priority Zone, should have Audio output : 1 x 3-pin terminals (Phoenix contact); 2x Digital Dante Network Audio or better, should have PoE powered or option of externally powered complete with standard accessories.
Supply, Installation, Testing & Commissioning of OEM Mounting Brackets for above ceiling microphone tile complete with std. accessories.
Supply, Installation, Testing & Commissioning of 2 core 16AWG PVC insulated Cu conduction speaker cable complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of Connectors & patch cables complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of 12U AV rack for the AV backend equipements such as Amplifier, Receivers etc. with required PDU's, mounting hardware for equipments, front glass door, movements wheels with brake complete with standard accessories as required.
Video System Supply, Installation testing & commissioning of 6,200 ANSI lumens 3-chip 3LCD projector having resolution Full HD 1080p, Contrast ratio 2,500,000:1, Horizontal and Vertical Keystone Correction ±30°, Should have 2 or more HDMI, 2 or more VGA, 1 or more HDBaseT, 2 or more Audio 3.5mm in, 2x USB, 1x Ethernet (RJ-45); Outputs: 1x HDMI out, 1x Audio 3.5mm jack out, Control: RS-232, LAN (RJ-45) Ethernet(10/100 RJ-45), Should have Throw distance of Projector from Screen: 5.85 Mtrs - 9.4 Mtrs or better complete with all standard accessories.
Supply, Installation, Testing & Commissioning of Mounting/ Hanging arrangements for the above given Display complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of Full HD IP PTZ camera with 12X optical zoom, Resolution 1080p@60Hz, Sensor 1/2.8" 2MP CMOS, Interfaces: 3G-SDI/ HDMI, 1x Mic/ line In, output: Ethernet, 1x USB3.0, Viewing angle (H/V) 72.5°/40.8°, Panning angle +170° ~ -170°, Tilting angle -30° ~ +90°, Video S/N Ratio >50dB, Features: Focus, Gain control, Exposure, Image flip, IP protocol RTSP/RTMP/RTMPS complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of Mounting/ Hanging arrangements for the above given Camera complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of 4K60 18Gpbs 2x1 multi-format presentation matrix switcher, Should have 1 or more HDMI in, 1 or USB-C for power & Data, 1 or more Should have 1 or more HDMI out, 1x HDBaseT outs, can transmit signal upto 70 Mtrs., USB switching Hub with switchable 2x USB3.0 Host port, 2x USB2.0 ports additional client ports, Support resolution up to 4K60Hz/4:2:0 8-bit color depth, HDCP2.2 compliance, EDID management, 1x RS-232 via TCP/IP, 1x Ethernet Control port complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of NUC PC, should have i5 Core 8 Gen. or better processor, 8GB RAM memory, 256 GB or more SSD, Should have Interfaces 2x HDMI, 1 or more USB3.0 Type-C port, 3 or more USB2.0 type-A, 1x Ethernet port (RJ-45) complete with standard accessories as required. (Note : Software/ License for VC conferencing shall be at Client scope)
Supply, Installation, Testing & Commissioning of 08-port POE Network Switch complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of 1 Mtrs USB-USB C-type cable, should have USB3.1 Gen 1 or better complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of 2 Mtrs USB 3.0 A to A (Male) Molded Cable complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of 3 Mtrs USB-USB, USB-A to USB-B moulded Cable complete with standard accessories as required.
Supply, Installation, Testing & Commissioning 2 Mtrs USB-USB Cable for Signal processor complete with standard accessories as required.
Supply, Installation, Testing & Commissioning 2 Mtrs HDMI-HDMI cable complete with standard accessories as required.
Supply, Installation, Testing & Commissioning 3 Mtrs HDMI-HDMI cable complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of Shielded twisted pair cable complete with standard accessories as required.
Audio System Supply, Installation, Testing & Commissioning Full range Ceiling loudspeaker with 1x 2.25"transducer, Frequency response: 95Hz to 16kHz; Power handling capacity: 16 Watt; Nominal dispersion: 145° Conical; Sensitivity: 86 dB SPL and Max SPL: 98 dB SPL; Nominal Impedance: 16 Ohms or 70/100V; Integral multi-tap Transformer with tap settings: 2/4/8/16 W @70V/100V. Installation: Indoor complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of Dual-channel proffessional Class-D low impedance power amplifier; Should have power output of 2x 50W @4Ω and 2x 25W @8Ω or better; Frequency response: 40Hz- 20kHz or better; Should have Input Impedance: 20 kΩ or better; Total harmonic distortion (THD): ≤0.3% or better; Should have Channel seperation (Crosstalk): ≤-60 dBV or better; Dynamic range: 88dB or better complete with standard accessories as required.
Supply, Installation testing & commissioning of A-weighted 32-bit fixed/floating-point DSP + ARM Cortex-A8; Frequency Response : 18 Hz – 20 kHz; 456 MHz Signal processor; Dynamic Range : > 115 dB; Input channel: 4-AEC analog (balanced, mic/line level); Output channel : 4-AEC analog (balanced, line level), 4 or more Digital output on RJ-45; Sample Rate : 48 KHz; THD+N : 0.003%; Channel seperartion(crosstalk): <-105 dB; Dante Expansion: 16X16, primary/secondary; USB Stereo in/out; VOIP (RJ-45 port); PSTN(RJ-11 port); Display: 256 x 64 OLED with rotary encoder; Ethernet (RJ-45); 100Mb network control complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of Ceiling Microphone tile with Min of 28 or more Pre-polarized condenser capsule or higher, Should have TruVoice Lift technology or better, Sound pressure level : max. 104 dB SPL, Dynamic range 93 dB(A) or better, should have Adaptive beamforming technology or better, should support Priority Zone, should have Audio output : 1 x 3-pin terminals (Phoenix contact); 2x Digital Dante Network Audio or better, should have PoE powered or option of externally powered complete with standard accessories.
Supply, Installation, Testing & Commissioning of OEM Mounting Brackets for above ceiling microphone tile complete with std. accessories.
Supply, Installation, Testing & Commissioning of 2 core 16AWG PVC insulated Cu conduction speaker cable complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of Connectors & patch cables complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of 12U AV rack for the AV backend equipements such as Amplifier, Receivers etc. with required PDU's, mounting hardware for equipments, front glass door, movements wheels with brake complete with standard accessories as required.
Video System Supply, Installation testing & commissioning of 6,200 ANSI lumens 3-chip 3LCD projector having resolution Full HD 1080p, Contrast ratio 2,500,000:1, Horizontal and Vertical Keystone Correction ±30°, Should have 2 or more HDMI, 2 or more VGA, 1 or more HDBaseT, 2 or more Audio 3.5mm in, 2x USB, 1x Ethernet (RJ-45); Outputs: 1x HDMI out, 1x Audio 3.5mm jack out, Control: RS-232, LAN (RJ-45) Ethernet(10/100 RJ-45), Should have Throw distance of Projector from Screen: 5.85 Mtrs - 9.4 Mtrs or better complete with all standard accessories.
Supply, Installation, Testing & Commissioning of Mounting/ Hanging arrangements for the above given Display complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of Mounting/ Hanging arrangements for the above given Camera complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of 4K60 18Gpbs 2x1 multi-format presentation matrix switcher, Should have 1 or more HDMI in, 1 or USB-C for power & Data, 1 or more Should have 1 or more HDMI out, 1x HDBaseT outs, can transmit signal upto 70 Mtrs., USB switching Hub with switchable 2x USB3.0 Host port, 2x USB2.0 ports additional client ports, Support resolution up to 4K60Hz/4:2:0 8-bit color depth, HDCP2.2 compliance, EDID management, 1x RS-232 via TCP/IP, 1x Ethernet Control port complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of NUC PC, should have i5 Core 8 Gen. or better processor, 8GB RAM memory, 256 GB or more SSD, Should have Interfaces 2x HDMI, 1 or more USB3.0 Type-C port, 3 or more USB2.0 type-A, 1x Ethernet port (RJ-45) complete with standard accessories as required. (Note : Software/ License for VC conferencing shall be at Client scope)
Supply, Installation, Testing & Commissioning of 08-port POE Network Switch complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of 1 Mtrs USB-USB C-type cable, should have USB3.1 Gen 1 or better complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of 2 Mtrs USB 3.0 A to A (Male) Molded Cable complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of 3 Mtrs USB-USB, USB-A to USB-B moulded Cable complete with standard accessories as required.
Supply, Installation, Testing & Commissioning 2 Mtrs USB-USB Cable for Signal processor complete with standard accessories as required.
Supply, Installation, Testing & Commissioning 2 Mtrs HDMI-HDMI cable complete with standard accessories as required.
Supply, Installation, Testing & Commissioning 3 Mtrs HDMI-HDMI cable complete with standard accessories as required.
Supply, Installation, Testing & Commissioning of Shielded twisted pair cable complete with standard accessories as required.
VKJ Projects Pvt. Ltd.
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid