Sewerage Interception and diversion works under Swachh Bharat Mission for Municipal Corporation Mandi Distt Mandi

Amount

Excavation in foundation and trenches etc. (including pipes and pits upto all depths) in all kinds of soil such as pick work, jumper work, blasting and chiselling soft or hard rock where blasting is prohibited in all leads and lifts including trimming and dressing of sides, levelling of bed to correct grade stacking the excavated soil clear from the edge of excavation and returning the excavated soil after laying, jointing and testing of GI pipes in trenches in 15cm layers including consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated soil as directed in all leads and lifts and soring strutting and trimming dressing where ever required including restoration of un-metalled surface to its original condition including cost of diversion for traffic night signals fixing caution board, crossing over trenches for access to houses and fencing etc. complete in all respect.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete 1:1.5:3(1cement:1.5 sand:3 crushed stone agg.20mm nominal size )& curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:

In foundation and plinth in all leads and lifts.

Walls (any thickness but not less than 0.1 m thickness) attached pillasters, buttresses, plinth and string courses, etc. from top of foundation level upto floor two level in all leads and lifts

Suspended floors, roofs,landings and shelves and their supports, balconies, beams, girders, bressumers and cantilivers up to floor two level in all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron in frames 30x30x5mm, so as to give a fair finish including centring, shuttering ,strutting and propping etc.with wooden battens and ballies,height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for in situ reinforced concrete and plain concrete work in:-

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillaster,buttresses, plinth and string courses and the like in all leads and lifts.

Flat surfaces such as soffits of suspended floors, roofs landings and the like: floors etc. up to 200 mm in thickness in all leads and lifts.

Edges of slabs and breaks in floors and walls in all leads and lifts.

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete up to floor two level in all leads and lifts.

Applying cement Slurry on RCC Slab or Cement Concrete work.

Providing and fixing CI Rungs complete in all aspects.

Brick work using common burunt clay building bricks in super structure above plinth level upto floor two level in cement mortor 1:6 (1cement : 6 sand) 2nd class bricks in all leads and lifts.

Providing and laying cement concrete 1:2:4 (1cement:2 sand:4 crushed stone agg.20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work:- Column,Pillars, post and struts upto floor two lvel with in all lead and lifts as per direction of Engineer-in-charge.

Providing and fixing Steel fibre reinforcement concrete (SFRC) manhole cover and frame conforming to IS-12593(Part-I)1988 and IS 12592-1991 Part-II with latest ammendments 560mmdia (Medium duty)in all leads and lifts.

Laying, jointing and testing in trenches Centrifugally cast (Spun) ductile iron pipes conforming to BIS-8329-2000 ( latest with up to date ammendments) in length of 5.50 mtr.class K7 with cement mortar lining in side duly ISI marked including cost of Tyton (Push or joints) fittings including testing of joints and rubber gasket(S&R quality)conforming to IS-92820-1989 (Earth work in trenches to be measured and paid for separately) in all leads and lifts. (i) 150mm dia (L.R)

Providing and jointing tyton (Push on joints) to Ductile iron pipe and fitting i/c testing of the joints, cost of rubber gasket(EDPM Quality) conferming to IS 3382 (Lastest edition /amendments) complete in all respect with in all leads and lifts.and as per latest amendments or Edition.

Providing and fixing SMC Panel water tank on PCC base along with floating valve, complete in all aspects.

Providing and fixing Cast Iron Gate Sluice Valve (Flanged) confirming to IS 4846 with flange Table -5 including welding of flanges, Nuts & Bolts and Gasket etc. The sluice valve conforming to (IS:210 GR FG-200) class PN 1.00. The dia of valve as mentioned below complete in all leads and lifts and to the entire satisfaction of the Engineer - in - Charge., (i) 65mm nominal bore

Laying in trenches, galvanized mild steel tubes (light grade), tube fittings (earth work in trenches to be measured & paid for separately) (i) 25mm nominal bore (LR)

Stone Soiling properly hand packed filling interstes with kharunja stone and consolidation with power road roller to the required gradient and chamber i/c spreading, watering and rolling of hinding material or earth work.

Providing and laying cement concrete 1:5:10 (1cement:5 sand:10 graded stone agg.40mm nominal size) and curing complete excluding cost of form work in retaining walls/breast walls,the size of plums shall usually by 150mm to 300mm as per HPPWD specifications in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3coarse sand) : 6 graded stone aggregate 40 mm nominal size)

Providing and applying tack coat with Bitumen Emlusion (RS-I) using emulsion distributor at the rate of 0.25 to 0.30 kg per Sqm on the prepared dry and hungry bituminous surface cleaned with hydraulic broom as technical specification Clause 503. in all respects and to the entire satisfation of Engineer-in-Charge.

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and type C as per Technical specification clause 510. in all respects and to the entire satisfation of Engineer-in-Charge.

Providing, laying and rolling of open graded premix carpet of 20mm thickness composed of 13.2mm to 5.6mm agrregates either using penetration gradeb bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base and including mixing in a suitable plant, laying and rolling with three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type В ог Type C as per Technical specification clause 508

White washing with lime on undecorated wall surfaces two coats to give an even shade including thoroughly brooming the surface to remove all dirt , dust and other foreign matters in all leads and lifts.

Providing and fixing MS grating including all leads and lifts.

Providing and fixing MS ISMB 200 including all leads and lifts.

Providing and fixing Exhaust Fan of reputed make including all leads and lifts.

Providing and fixing Pannel Door (Aluminium) i/c frame etc. complete in all respect and as per the direction of Engineer-in-charge.

Providing and fixing Non clog type submersible sewage pumps with suitable motor of reputed make & model for following duty condition with guide rail system, lifting chain and protection system complete in all respects and to the entire satisfation of Engineer-in-Charge. Intermittent Pumping Station at Khaliyar

Discharge 1.04 LPS and Head 19.53 meter and length of Rising Main 100 mm dia =1370 Meter

Discharge 2.08 LPS and Head 19.53 meter and length of Rising Main 100 mm dia=1370

Discharge 5.21 LPS and Head 19.53 meter and length of Rising Main 100 mm dia=1370 Meter

Intermittent Pumping Station at Indira Market

Discharge 1.62 LPS and Head 7.91 meter and length of Rising Main 100 mm dia=300 Meter

Discharge 0.8 LPS and Head 7.91 meter and length of Rising Main 100 mm dia=300 Meter

Discharge 4.05 LPS and Head 7.91 meter and length of Rising Main 100 mm dia=300 Meter

Automatic Control Pannel with starter, main MCB, Voltmeter, Amp meter, Power Capacitor, Control MCb, Supply & Motor Side Cable/NRV/ Sluice valve/Common Header Job/Earthing and the all other required components as per the relevant IS code ( latest edition & CPHEEO Mannual) in all respects and to the entire satisfation of Engineer-in-Charge.

Providing, Laying & Jointing of (100 mm dia) Duticle Iron Pipe (flanged Joint) i/c all types of bends and EPDM Rubber Gasket as per CPHEEO mannual (Lastest Editions)as per the site requiremnt and as per the direction of Engineer - In Charge.

Providing & Fixing Screen Size Bar (10x50 mm) i/c all respect and as per direction of the Engineer In Charge

Manufacturing & Supplying of fencing panel of size 2.40m x 1.20m fixed on all sides with ISA 40x40x5mm as per drawing. Three pieces of similar section of 0.25m long be fixed at the bottom frame & two pieces of 20x4mm flat on both the vertical sides be fixed as hold fast. The operation of manufacturing shall including cutting of Hard-drawn steel wire fabric square mesh of 3.0mm wire and 25mm pitch, Angle Section & welding of wire mesh, angle with 20x4mm flats on all four sides and applying a priming coat of steel primer after pretreatment of surface to the entire satisfaction of the Engineer-in-Charge.

Providing and fixing Oxidised MS sliding door bolts with bolts and nuts screws etc.complete 250 x 16 mm in all leads and lifts.

Providing and fixing Cleats with nuts to rest a pintless complete in all leads and lifts. sliding door bolts with bolts and nuts screws etc.complete 250 x 16 mm in all leads and lifts.

Steel work built up section,trusses and framed work ,including cutting hoisting and fixing in position and applying a priming coat of red lead paint:- In gratings framed guard bars,ladders ,railing brackets and similar works in all leads and lifts.

Providing, Supplying and fixing of Precast RCC Manhole Chamber of internal size 600x600 mm, including ISI marked heavy-duty RCC manhole cover and frame conforming to IS: 12592 (Part 2) – 2002, complete in all respects and to the entire satisfation of Engineer-in-Charge.

Repair of PWD Road Damaged During Laying of Sewer line in all respects and to the entire satisfation of Engineer-in-Charge.

Providing, supplying, installation, testing and commissioning of submersible sewage pump set (Non clog) with suitable motor of reputed make & model having discharge capacity of 3.00 LPS against 15 mtr. head for emptying domestic septic tanks complete in all respects i/c electrical and machenical allied accessories and to the entire satisfation of Engineer-in-Charge.

Providing, lowering, laying and jointing HDPE pipe (confirming to IS 4984-2016) in proper position by butt fusion joining procedure including hydraulic testing as per relevant IS Code, complete with all material for joining procedure like butt fusion welding machine with hydraulic jack, top loading clamp etc. pump and accessories for hydraulic testing and all labours as directed by engineer in charge (50 mm HDPE for House connection (14 No. HH) 60-meter per HH)

Annual comprehensive maintenance contract of sewage pumping station located at Indira Market 0.18 MLD cap. for 3 years i/c pumps, motors, panel,volves and associated electro mechenical equipment complete in all respects and to the entire satisfation of Engineer-in-Charge.

For 1st Year

For 2nd Year

For 3rd Year

Annual comprehensive maintenance contract of sewage pumping station located at Bijani 3.00 MLD cap. for 3 years i/c pumps, motors, panel,volves and associated electro mechenical equipment complete in all respects and to the entire satisfation of Engineer-in-Charge.

For 1st Year

For 2nd Year

For 3rd Year

Providing and installation of DG Set Three Phase 15 Kva for Wet well Bijni & Indira Market complete in all respects and to the entire satisfation of Engineer-in-Charge.

Providing, Supplying, Testing & Commissioning of Trailer mounted Sewer Jetting Machine equipped with jetting pump of repeted make having discharge of 50 LPM and pressure range 120-150 Base mounted with 10 HP petrol engine, jetting hose pipe of suitable dia and 80m length, spported by Pneumatic tyres completed in all respects and to the entire satisfation of Engineer-in-Charge.

KRP Engineering Pvt. Ltd. (BID ID -563480)

Tek Singh Raghav (BID ID -562269)