Loading
Loading…
Loading…
Tender Value
₹1.1 Cr
EMD Value
₹2.2 L
Closing Date
7 Sept 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
GENERAL
15 conditions · 4 needing a document upload
(As per advance correction slip No.1 of GCC April 2022) The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB of GCC-April-2022 along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Annexure V :- As per Clause 6.1 Part-1 of GCC- The tenderer shall submit a copy of certificate (Enclosed as Annexure-V) stating that all their statements/documents submitted alongwith bid are true and factual. Non submission of above certificate by the bidder shall result in summarily rejection of his/their bid.
The minimum Eligibility Criteria: for costing more than 50 lakhs :- Applicable. 10. Eligibility Criteria: 10.1 Technical Eligibility Criteria: (a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b)(1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b (1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution
Note for Item 10.1: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate. 10.1Definition of similar works : The criteria for similar nature of work for said tender is given below as CEE/JBP's L. No. WCR/L/10/Similar Nature/3689, dtd. 11.04.2012. similar nature of work criterion for Electrical General Service (GS) for Electrification work in Electrical department of WCR shall include works executed with Central Government, Semi Government/PSUs of Central Government and/or State Governments have been defined as under :- (A)The level of skills required in following work of electrification is almost same. (a) Electrification of service buildings. (b) Electrification of staff quarters, offices. (c) Electrification of offices. (d) Electrification of road & colony lighting. (e) Electrification of circulating area lighting. (f) Erection & commissioning of LT, HT upto 33 kV overhead mains. (g) Sub-station installations & commissioning. (h) Electrification of washing pits, Sheds & Workshops etc. (i) Any above work or combination of (a) to (h) above.
30 conditions · 3 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
This tender complies with Public Procurement Policy (Make in India) Order 2017, dated 15/06/2017, issued by Department of Industrial Promotion and Policy, Ministry of Commerce, circulated vide Railway Board letter no.2015/RS(G)/779/5 dated 03/08/2017 and 27/12/2017 and amendments/ revisions thereof.
Additional 5% PG to be submitted if tender awarded more than 5% below (Ref : para-4 of Rly. Bd. L.No.2022|CE- UCTIGCC2022[POLICY/Pt.I (E-3320424), Dated 13.03.2026
Kota Division: Provision of Track Machine siding with facilities (11 Station - JHW, RDT, ALNI, LKE, URML, SNAR, THEA, MLGH, PSLI, MXL, FSP), KOTA-COR Section - Improvement of TTM siding at Bundi and MLGH station and Upgradation / renovation of TTM Rest House at BUDI and MLGH, Providing New Office Building for CMI, TI, ARME & USFD etc on replacement basis at SGZ station and provision of New Trade union Office on replacement basis at SGZ & VMA Station and Providing to Subordinate Rest House SGZ & TTM Rest House at CMU, VMA & Improvement / Repairs to SRH/TTM Rest House at MEP under ADEN/SGZ.
EL-50-329R-2026-27~WCR
EL-50-329R-2026-27
Open
Works - General
9 Months
Kota, Rajasthan
₹0
₹2.2 L
11 Aug 2026
11 Aug 2026
24 Aug 2026
155 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,12,46,340.61 | ||
| — | 55.00 | — | — | ||
| Supply and erection of octagonal galvanized steel pole 5 mtr long with foundation bolts, single arm type etc. with junction box and cover complete. (a)Pole ID-BOP 5030 (b)Height-5 meter ©Top-70mm (d)Bottom-130mm (e)Thickness-3mm (f)Base plate-200x200x12 mm (g)Foundation bolts-PCD-200 : bolt size 4x16mmx600mm long (IS:1367,Part-III) (h)Single arm brackets (i) Foundation size (WxLxH) 500x500x1000 mm. Note: -1. Octagonal steel poles with foundation bolts should be confirming to std. 35 grade. Base Plate IS 226/IS 2062. Grade of PCC should be M-20 2. All material will be supplied by contractor. | — | — | — | 10,46,007.6 | |
| — | 102.00 | — | — | ||
| Supply and installation of LED Street light fitting 30 watt suitable for 230 V AC. | — | — | — | 1,02,033.66 | |
| — | 47.00 | — | — | ||
| Supply & fixing of 'B' class GI pipe fitting made for 40mm dia for fixing of CFL fittings with all required accessories i.e. MS clamps, nut bolt washers etc. | — | — | — | 26,618.92 | |
| — | 10050.00 | — | — | ||
| Laying of circular armoured XLPE LT cable size 4 core aluminum conductor 1100 volt with connection etc. (Note: Cable will be supplied by Railway.) | — | — | — | 2,27,230.5 | |
| — | 1230.00 | — | — | ||
| Digging of trench in pucca trench in yard /platform 50cm. deep and 35cm. wide including replaster on surface by cement concrete after laying of cable. | — | — | — | 2,60,083.5 | |
| — | 7415.00 | — | — | ||
| Digging of trench in all type of soils/road cutting 100 cm. deep and 50cm. wide including supply and laying of "B" class bricks on both side & top of the cable and refilling the trench after laying of cable. | — | — | — | 9,83,599.75 | |
| — | 180.00 | — | — | ||
| Supply of material, providing and laying of RCC hume pipe 6" dia (150mm) as per IS: 456-1978 or latest in existing trench under Railway track including jointing and all required accessories etc. | — | — | — | 89,341.2 | |
| — | 155.00 | — | — | ||
| Drilling of Horizontal bore below track/road by pushing method for laying of HDPE/DWC pipe of various size. | — | — | — | 5,96,591.9 | |
| — | 255.00 | — | — | ||
| Supply of material, providing, commissioning and laying of DWC/HDPE pipe of 160/138 mm dia cabling under road/track. | — | — | — | 1,36,358.7 | |
| — | 100.00 | — | — | ||
| Supply, laying, fixing of heavy-duty ISI marked B class GI pipe of 3.65 mm wall thickness & 50 mm diameter to be laid along the wall or floor with proper galvanized clamp through the wall or underneath the floor in cement concrete. | — | — | — | 38,478 | |
| — | 85.00 | — | — | ||
| Supply of material & providing GI. pipe earthing arrangement by digging the pit as per DRM/KTT's Drg. No. 01913EL/R1 or latest complete in all type of soils including rocky area. Earth value will be taken by the contractor in the presence of Railway representative and written on the earth pit by the contractor. | — | — | — | 1,61,049.5 | |
| — | 15.00 | — | — | ||
| Supply, fabrication, installation, testing & commissioning of LT distribution board fabricated With M.S. angle size 40x40x3mm with door & locking arrangement duly painted red oxide & powder coated enamel Paint consisting of following items. Incoming - MCCB TPN 100 Amp. Breaking cap. 35 KA - 01 No. Outgoing - MCB 63 Amp. TPN - 02 Nos. | — | — | — | 3,03,150.9 | |
| — | 12.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of 63 Ampere, 5 pin 415 VAC Industrial Plug and socket Distribution Box with 63 Ampere, four pole, C curve, 10 KA MCB. All should be complete in all respect. | — | — | — | 82,973.04 | |
| — | 16.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of 32 Ampere, 3 pin 415 VAC Industrial Plug and socket Distribution Box with 32 Ampere, two pole, C curve, 10 KA MCB. All should be complete in all respect. | — | — | — | 32,261.44 | |
| — | 12.00 | — | — | ||
| Supply, Erection, Testing and Commissioning LT junction Box /Bus bar box of four copper bus bar having rating 100 Amps for outdoor usage with nut & bolt complete in all respect. | — | — | — | 48,746.16 | |
| — | 259.00 | — | — | ||
| Supply & fixing of LED tube light Box type Luminaire 20 watt complete with tube suitable for 230 V AC. | — | — | — | 93,423.89 | |
| — | 104.00 | — | — | ||
| Supply and fixing of BEE 5 star rated energy efficient BLDC ceiling fan, sweep size: 1200mm, complete with wiring connection etc. as per detailed specification attached. | — | — | — | 2,50,822 | |
| — | 41.00 | — | — | ||
| Supply, Fixing, testing & commissioning of exhaust fan sweep size 300 mm suitable for 230-volt AC 50 Hz complete with accessories. | — | — | — | 47,675.62 | |
| — | 22.00 | — | — | ||
| Supply, Fixing, testing & commissioning of Bulkhead fitting wire mesh suitable for 7/8/9 watts LED lamp with LED lamp 07 watts suitable for 230 volts AC. | — | — | — | 11,856.9 | |
| — | 110.00 | — | — | ||
| Supply of material and wiring, testing and commissioning of light/fan point in PVC rigid conduit pipe size 19/20 mm medium class with 1.5 sqmm multistrand PVC insulated copper conductor cable confirming to IS: 694-1990 or latest amd 2.5 sqmm PVC insulated copper wire coloured for earthing along with connections etc. | — | — | — | 49,684.8 | |
| — | 165.00 | — | — | ||
| Supply of material and wiring, testing and commissioning of sub main phase and neutral in PVC rigid conduit pipe size 25 mm dia. medium class mark with 4 sq.mm. PVC insulated single core multistransd copper cable with 2.5 sq.mm. PVC insulated copper wire green coloured for earthing and connection etc. Separate PVC pipe to be provided for this item. | — | — | — | 14,904.45 | |
| — | 31.00 | — | — | ||
| Supply of materials and fixing of main distribution box 4+2 way suitable for housing MCB and ELCB with neutral link. Distribution box should be fixed on wooden taper plug or steel fasteners etc. with supply and fixing of 01 no. MCB SPN 16 Amp. breaking capacity 10 KA and 02 Nos. MCB SP 6-32 Amp. breaking capacity 10 KA with 01 No. ELCB 25 Amp. DP, sensitivity 30 m.Amp. and connections etc. The distribution board is to be fixed on wall with the help of rag bolt /fastener or on board and connecting the same with suitable size of wire duly crimped lugs. | — | — | — | 1,21,217.75 | |
| — | 6.00 | — | — | ||
| Supply & fixing of Energy efficient 5 star rated submersible pump motor set 150mm dia, Head 214-110 mtr., Motor rating 7.5 H.P., Discharge 50-150LPM ,3 phase 415-volt AC Confirming to IS NO.-8034/1989 & motor conf. to IS NO.-9283/1995 or latest. | — | — | — | 2,19,176.82 | |
| — | 6.00 | — | — | ||
| Supply of Energy efficient 5 star rated submersible pump motor set 150mm dia, Head 214-110 mtr., Motor rating 7.5 H.P., Discharge 50-150LPM ,3 phase 415-volt AC Confirming to IS NO.- 8034/1989 & motor conf. to IS NO.-9283/1995 or latest. | — | — | — | 2,05,450.2 | |
| — | 3.00 | — | — | ||
| Supply, installation, testing & commissioning of Energy saver VOS pump motor set Water Lubricated ISI mark 7.5H.P.,2 stage, head-30 mtr., discharge10 LPS delievey size outlet 63 mm confirm to IS no. - 14220 and 1994 or latest. | — | — | — | 1,60,191.99 | |
| — | 3.00 | — | — | ||
| Supply of Energy saver VOS pump motor set Water Lubricated ISI mark 7.5H.P.,2 stage, head-30 mtr., discharge10 LPS delivery size outlet 63 mm confirm to IS no. - 14220 and 1994 or latest. | — | — | — | 1,52,598 | |
| — | 9.00 | — | — | ||
| Supply and fixing of star-delta starter panel board suitable for 7.5 HP to 20 HP submersible pump motor set 3 phase 415 volt AC complete as per following specification :-(1)push button with light 230V-02 nos. (2) Auto time switch 16 amp 230 V -01 nos. (3) single phase preventor vsp2 415v - 01 nos. (4) Digital ampere meter with selector switch - 01 nos. (5) Digital voltmeter 500V -01 nos (6) MCCB 4 pole breaking capacity 63 AMP. - 01 nos. (7) Digital hour meter 230 V - 01 nos (8) HRC fuse unit 63 A complete - 03 nos. (9) electronic motor protection relay 5-60 amp.CSMPA@45<45@T,60A,220 VAC - 01 nos. (10)two way toggle switch 10 amp for manual auto - 01 nos. (11) star delta timer 0-60 sec. - 01 nos. (12) 03 pole contactor 70 amp 3 phase with aux. block (2 NO+2 NC) - 03 nos.(13) CT 50/5 per unit - 03 nos. (14) Control fuse - 03 nos. (15) Water level control guard of 3 prode system - 01 nos. (16) Average dimension 640X500X290 mm.(17) LED indicating lamp for motor on, motor trip & RYB phase indicator - 05 nos. (NOTE :- ALL SWITCH GEAR TO SEPARATE ) | — | — | — | 5,81,541.84 | |
| — | 2.00 | — | — | ||
| Supply & fixing of Energy efficient submersible pump motor set 5 HP 3 Phase, 415 olt AC, 50 Hz, Head Range 62-170 Mtr., Discharge 167-33 LPM (V4), Confirming to IS NO.-8034/2002 or latest. | — | — | — | 57,618 | |
| — | 2.00 | — | — | ||
| Supply of Energy efficient submersible pump motor set 5 HP 3 Phase, 415 olt AC, 50 Hz, Head Range 62-170 Mtr., Discharge 167-33 LPM (V4), Confirming to IS NO.-8034/2002 or latest. | — | — | — | 52,470 | |
| — | 2.00 | — | — | ||
| Supply of Directon Line Starter Panel 5 HP to 7.5HP three phase 415-volt AC, Powder Coated 18 SWG Sheet Steel Enclouser with PU Gasket Duly Wired and Locking Arrangement with key and Two side ventilation Louvers | — | — | — | 63,194 | |
| — | 2.00 | — | — | ||
| Installation, testing &commissioning of Direct On-Line Starter Panel 5HP to 7.5 HP three phase 415-volt AC, Powder Coated 18 SWG Sheet Steel Enclouser with PU Gasket Duly Wired and Locking Arrangement with key and Two side ventilation Louvers | — | — | — | 1,170 | |
| — | 1.00 | — | — | ||
| Supply, installation, testing & commissioning of Energy efficient ISI mark submersible pump motor set 3 HP/23 stage, 220 Volts, H/range 71-136 mtr, discharge - 100 - 33 LPM, Del. 38/40 mm suitable for 100 mm dia bore well, water lubricated type as per expanatory notes. | — | — | — | 22,164.48 | |
| — | 1.00 | — | — | ||
| Supply of Energy efficient ISI mark submersible pump motor set 3 HP/23 stage, 220 Volts, H/range 71-136 mtr, discharge - 100 - 33 LPM, Del. 38/40 mm suitable for 100 mm dia bore well, water lubricated type as per expanatory notes. | — | — | — | 19,590.48 | |
| — | 1.00 | — | — | ||
| Supply & fixing of control starter panel with voltmeter 0-300 V, Ammeter 0-30 Amp., indicators, On-Off push button, motor protection overload relay 17-24 Amp., contactor 25 Amp. & suitable for 03 HP single phase submersible motor pump set with starting and running capacitor. | — | — | — | 5,824.72 | |
| — | 750.00 | — | — | ||
| 94.06 Supply, erection, testing and commissioning of PVC insulated flat three core flexible copper industrial cable for submersible pump motor set 1.1 K.V. grade nominal area of conductor 4.0 sqmm as per latest relevant IS: 694 or latest. | — | — | — | 70,545 | |
| — | 3000.00 | — | — | ||
| Supply, erection, testing and commissioning of PVC insulated flat three core flexible copper industrial cable for submersible pump motor set 1.1 K.V. grade nominal area of conductor 6.0 sqmm as per latest relevant IS: 694 or latest. | — | — | — | 5,75,940 | |
| — | 3300.00 | — | — | ||
| Supply & fixing of HDPE Pipe outer diameter 63 mm, material grade PE-63, Pressure- 10 PN, ISI Mark, IS: 4984-2016 or latest complete with SS hose nipple and nut bolts etc. | — | — | — | 7,67,877 | |
| — | 400.00 | — | — | ||
| Supply & fixing of HDPE Pipe outer diameter 50 mm, material grade PE-63, Pressure- 10 PN, ISI Mark, IS: 4984-2016 or latest complete with SS hose nipple and nut bolts etc. | — | — | — | 68,796 | |
| — | 300.00 | — | — | ||
| Supply & fixing of HDPE Pipe outer diameter 40 mm, material grade PE-63, Pressure- 10 PN, ISI Mark, IS: 4984-2016 or latest complete with SS hose nipple and nut bolts etc. | — | — | — | 35,865 | |
| — | 4000.00 | — | — | ||
| Supply & fixing of Poly Propylene rope 3 strand hawser laid and 8 stand plited size 16 mm dia Conf. to IS: 14929-2001 along with 42 nos. hardware to secure the complete pump motor to prevent it from falling down in the borewell breaking capacity 3770 Kgf plus minus 6 percent. | — | — | — | 1,24,440 | |
| — | 20.00 | — | — | ||
| Supply & fixing of MCB DP 16/25/32Amp with Box. | — | — | — | 15,091 | |
| — | 400.00 | — | — | ||
| Supply of Stranded compacted circular aluminium conductor A2XFY conductor screened with extruded , semi conducting compound XLPE insulated screened with extruded semi conducting compound in combination with copper tape (0.3 kA to 1 sec) core laid up inner sheath (ST-2) PVC galvanized steel strip armoured and overall PVC sheathed black cable HT cable size 3 core x 70 sqmm suitable for 11 kV(E) 6.6 kV (UE) confirming to IS 7098(Part-II) 1985 /with latest amendments. | — | — | — | 2,80,000 | |
| — | 400.00 | — | — | ||
| Laying, testing and commissioning of Stranded compacted circular aluminium conductor A2XFY conductor screened with extruded , semi conducting compound XLPE insulated screened with extruded semi conducting compound in combination with copper tape (0.3 kA to 1 sec) core laid up inner sheath (ST-2) PVC galvanized steel strip armoured and overall PVC sheathed black cable HT cable size 3 core x 70 sqmm suitable for 11 kV(E) 6.6 kV (UE) confirming to IS 7098(Part-II) 1985 /with latest amendments. | — | — | — | 12,824 | |
| — | 14.00 | — | — | ||
| Supply and fixing of 11 kV cable end box outdoor type heat shrinkable type for 11kV XLPE 3 core 50-95 sqmm size and connection with crimped lugs on cable end box. | — | — | — | 43,433.74 | |
| — | 12.00 | — | — | ||
| Supply, erection, testing & commissioning of GO switch 11KV 400Amp 3pole with 9 Nos insulators operating handle along with locking arrangement system hot deep galvined vertical type. | — | — | — | 2,62,797.24 | |
| — | 12.00 | — | — | ||
| Supply, erection, testing & commissioning of DO switch fuse 11KV 400Amp pole operated outdoor vertical mounting expulsion type having hot deep galvined base post type insulator and fiber glass fuse carrier. | — | — | — | 1,73,545.32 | |
| — | 4.00 | — | — | ||
| Supply, erection, testing & commissioning of 11KV gapless metal oxide lighting arrester complete with hardware, fixtures, hot dipped galvanised pin, nut, bolts, washers etc to relevant ISS. | — | — | — | 32,731.92 | |
| — | 8.00 | — | — | ||
| Supply of material and providing of copper plate Earthing arrangement by digging the Pit. Copper Plate size 600 X 600 X 3 mm as per drg.No.DRM/KOTA/01927/ELR. | — | — | — | 73,093.76 | |
| — | 2.00 | — | — | ||
| Supply & Erection of material for fabricated steel work other than mast with SPS. | — | — | — | 1,78,613.6 | |
| — | 16.00 | — | — | ||
| Supply & fixing of 9 mtrs long steel joist pole size 175 mm X 85 mm approx weight 19.1 Kg/m. | — | — | — | 2,95,443.52 | |
| — | 4.00 | — | — | ||
| Supply, Installation, fabrication, testing & commissioning of LT Distribution panel Enclosure 16 Gauge fabricated with MS angle Size 1575X1200X400 mm (HXWXD) approx. with door and locking arrangement duly painted red oxide and power coated enamel paint consisting of following items - INCOMING CIRCUIT- 01 No. MCCB 4 pole 160 Amp. 25 KA TM Release, Type: DN1- 250C, 415V AC, 50 HZ. Ampere meter with selector switch -01 no., voltmeter with selector switch -01 no., indication lamp RYB 03 nos., Changeover Onload Manual 160 Amp. 04 Pole 01 no. with indicator 02 no., CT 150/5A 15VA- 03 nos., Copper busbar Main 200 Amp. rating- 01 set & Earth 200 Amp. - 01 Set, MCB 6A SP C 10KA - 04 nos. OUTGOING CIRCUIT- TM Release 04 no. MCCB 4 pole 63 Amp. 25 KA. All MCCB in incoming and outgoing circuit will be provided with Extended Rotary Handle and Spreader Terminals - 4 Pole (Set of 8) etc. as per attached detailed specification. | — | — | — | 5,38,984.32 | |
| — | 18.00 | — | — | ||
| Supply and fixing of wall mounted bracket fan sweep 400 mm suitable for 230 volts, 50 hz moving type with regulator and control switch on & off with accessories. | — | — | — | 30,991.86 | |
| — | 528.00 | — | — | ||
| Supply, installation, testing & commissioning of concealed wiring of light/Fan/Bell points in PVC rigid conduit pipe size 25mm dia medium class minimum thickness approx. 1.6mm to 1.8mm of ISI mark with 1.5 sq.mm. multistrand PVC insulated copper conductor cable confirming to IS:694-1990 or latest with one holder/ceiling rose on junction box with round plate with 2.5 sq.mm. PVC insulated copper wire green coloured for earthing along with connection etc. including stone wall cutting, replaster, painting and other civil work | — | — | — | 1,88,971.2 | |
| — | 2280.00 | — | — | ||
| Supply, Erection, testing & commissioning of material for concealed wiring of sub main phase & neutral in PVC rigid conduit pipe size 25mm dia medium class minimum thickness approx. 1.6mm to 1.8mm of ISI mark with 4 sq.mm. PVC insulated single core multistrand copper cable with 2.5 sq.mm. PVC insulated copper wire green coloured for earthing & connection etc. Separate PVC pipe to be provided for this item. including stone wall cutting, replaster, painting and other civil work | — | — | — | 2,61,196.8 | |
| — | 20.00 | — | — | ||
| Supply of material & fixing of flush metal box of 12-Module with connection used for concealed modular flush metal box wiring. | — | — | — | 5,660 | |
| — | 20.00 | — | — | ||
| Supply of material & fixing of plate Inner & Outer 12-Module used for concealed modular wiring. | — | — | — | 5,764.8 | |
| — | 26.00 | — | — | ||
| Supply of material & fixing of flush metal box of 8-Module with connection used for concealed modular flush metal box wiring. | — | — | — | 5,333.38 | |
| — | 26.00 | — | — | ||
| Supply of material & fixing of plate Inner & Outer 8-Module used for concealed modular wiring. | — | — | — | 9,106.76 | |
| — | 71.00 | — | — | ||
| Supply of material & fixing of flush metal box of 6-Module with connection used for concealed modular flush metal box wiring. | — | — | — | 15,199.68 | |
| — | 71.00 | — | — | ||
| Supply of material & fixing of plate Inner & Outer 6-Module used for concealed modular wiring. | — | — | — | 29,844.14 | |
| — | 34.00 | — | — | ||
| Supply of material & fixing of flush metal box of 4-Module with connection used for concealed modular flush metal box wiring. | — | — | — | 4,729.06 | |
| — | 34.00 | — | — | ||
| Supply of material & fixing of plate Inner & Outer 4-Module used for concealed modular wiring. | — | — | — | 9,583.24 | |
| — | 51.00 | — | — | ||
| Supply of material & fixing of flush metal box of 3-Module with connection used for concealed modular flush metal box wiring. | — | — | — | 5,295.33 | |
| — | 51.00 | — | — | ||
| Supply of material & fixing of plate Inner & Outer 3-Module used for concealed modular wiring. | — | — | — | 12,034.98 | |
| — | 29.00 | — | — | ||
| Supply of material & fixing of flush metal box of 2-Module with connection used for concealed modular flush metal box wiring. | — | — | — | 2,183.41 | |
| — | 29.00 | — | — | ||
| Supply of material & fixing of plate Inner & Outer 2-Module used for concealed modular wiring. | — | — | — | 4,514.14 | |
| — | 292.00 | — | — | ||
| Supply of material & fixing of S.P. switch 6 Amp. one way (1-Module) used for concealed modular wiring. | — | — | — | 33,074.84 | |
| — | 127.00 | — | — | ||
| Supply of material & fixing of 6 Amp. 5-pin socket (2-Module) used for concealed modular wiring. | — | — | — | 24,665.94 | |
| — | 82.00 | — | — | ||
| Supply of material & fixing of fan regulator 5-step (2-Module) used for concealed modular wiring. | — | — | — | 55,473.82 | |
| — | 40.00 | — | — | ||
| Supply of material & fixing of S.P. switch 16 Amp. one way (1-Module) used for concealed modular wiring. | — | — | — | 8,467.6 | |
| — | 40.00 | — | — | ||
| Supply of material & fixing of 6/16 Amp. 6-pin combined shuttered socket (2-Module) used for concealed modular wiring. | — | — | — | 11,653.2 | |
| — | 70.00 | — | — | ||
| Supply & fixing of blank plates (1-Module) used for concealed modular wiring. | — | — | — | 2,217.6 | |
| — | 12.00 | — | — | ||
| Supply of materials and fixing of main distribution box 10 way suitable for housing MCB and ELCB with copper busbar and neutral link. Distribution box should be fixed on wooden taper plug or steel fasteners etc. with providing and fixing of 01 no. MCB DP 32 Amp. breaking capacity 6 KA and 06 Nos. MCB SP 6-32 Amp. breaking capacity 6 KA with 01 No. ELCB 40 Amp. DP, sensitivity 100 m. Amp. and connections etc. The distribution board is to be fixed on wall with the help of rag bolt /fastener or on board and connecting the same with suitable size of wire duly crimped lugs. | — | — | — | 60,924.48 | |
| — | 14.00 | — | — | ||
| Supply & fixing of MCB DP 16Amp. | — | — | — | 9,562.42 | |
| — | 40.00 | — | — | ||
| Supply & fixing of Recess mounting fitting LED Panel 36 Watt in 2' x 2' size. Optics diffuse for 230 Volt, 50 hz cut out size 595 x 595 mm. | — | — | — | 49,618.8 | |
| — | 2.00 | — | — | ||
| Supply, Installation, Testing & commissioning of LED name board Hindi and English word, and One Indian Railway Logo board as per attached specification. | — | — | — | 5,48,563.4 | |
| — | 365.00 | — | — | ||
| Supply of material & fixing of S.P. switch 6/10 Amp. one way (1-Module) used for concealed modular wiring. | — | — | — | 36,587.6 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Clarification for Annexure V
ATTACHMENT
GCC_April-2022_Final.pdf
ATTACHMENT
Annexure of LC
ATTACHMENT
Annexure-E.pdf
ATTACHMENT
TSEL-50-329R-2026-27_2.pdf
ATTACHMENT
Technical Specifications of LED
ATTACHMENT
DempoymentofEngineers.pdf
ATTACHMENT
CorrectionslipofGCC.pdf
ATTACHMENT
MakeinIndiapolicylatestamendment.pdf make in india policy
ATTACHMENT
GCCAdvanceCorrectionSlipNo11.pdf
ATTACHMENT
AnnexureLC-Inclusionofletterofcredit.pdf
ATTACHMENT
Clarification-Annexure-VofGCCwithTenders..pdf
ATTACHMENT
SpecificationofLEDLuminare-2026-1.pdf
ATTACHMENT
MakeinIndiapolicylatestamendment.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].