S.R. to Distillery Office Building (Repairs to DEE Chamber, PB Room, Clerk Room, Toilet, Parking, Paver Block & Internal Road of Distillery Office Campus) At Dharampur Ta. Dharampur, Dist. Valsad.

Sr. Description of Item Quantity Unit Rate Amount

1 Removing and scraping of old deteriorated plaster of any thickness fromm 81.00 Sq.Mt. 19.57

wall / R.C.C member including stacking of serviceable material and disposal

of unserviceable from site of work with all lead and lift

2 Providing 15mm thick cement plaster in single coat on Rough (Similar)side of 56.00 Sqmt 153.20

single or half brick walls for interior plastering upto floor two level and

finished even and smooth in Including Chiken Wire Mesh (i) Cement mortar

1:3 (1-cement:3-sand)

3 Providing 10mm thick cement plaster in single coat on brick/concrete walls 25.00 Sqmt 140.95

for interior plastering upto floor two level and finished even and smooth in

Including Chiken Wire Mesh (i)Cement mortar 1:3 (1-cement:3-sand)

4 Dismentaling tiled of stone floors laid in mortar including stacking of 43.00 Sqmt 48.21

serviceable materilas and disposal of unserviceable materials with all lead

5 Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in flooring 25.00 Sqmt 1073.13

treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3

(1-cement : 3-coarse sand ) finishing with flush pointing in white cement.

6 Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in skrting 2.50 Sqmt 1141.45

risers of steps and dedo on 10mm thick cement plaster 1:3 (1- cement : 3-

coarse sand) and jointed with white cement slurry

7 Providing and fixing full height Prelam PVC partition system 50mm thick 140.00 Sqmt 2173.52

consisting of 40mm sandwich PVC panel made out of 36mm high density

expanded polystyrene sheet (E.P.S. Thermocol) stuck on both side with 2mm

thick prelim PvC sheet reinforced with frame work made from 35mm x 5mm

M.S. angle. In between two M.S. angles 4 mm with feathered edges shall be

fixed on floor and 50 x 75 mm with feathered edges prelim PVC “C” channel

of size 50mm x 75mm with feathered edges prelim PVC panel shall be

inserted in the PVC ‘C” channel The first and last M.S. angle should be

erected such that it is inside a PVC C channel of size 50 x 75mm In between

adjoining EPS sandwiched PVC partition panel 4mm thick x 75 mm width

prelim PVC sheet feathered at edges shall be stuck on front and back face

using solvent cement etc. An additional 4mm thick PVC strip of 40mm width

is to be stuck on the intrior side of the ‘C” channel using PVC solvent

adhesive completeas per direction of Engineer in charge. Manufacture’s

specification and drawing.

8 Providing and fixing eco-friendly light weight calcium silicate false ceiling 184.00 Sqmt 1648.96

tiles having Tegular edge & 15 mm Thick Densified edges on the Tile

Periphery for Extra Strength The Light weight calcium silicate ceiling tiles

shall have , light reflection 85% non-combustible as per B.S. 476 part IV,

100% humidity resistance and also having thermal conductivity0.043° w/m

KC.for the best thermal Insulation . The Light weight calcium Silicate tile shall

be of approved texture Fine fissured/ Spintone/Cosmos having NRC value

of 0.5 & Globe having NRC value of 0.75 NRC or equivalent of size 595 X

595 mm to be laid on true horizontal level suspended inter locking metal grid

of hot dipped galvanized steel sections (galvanizing @120 grams per sqm

including both side) consisting of main ‘T’ runner suitably spaced at joints to

get required length and size of 24X38mm made from 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size 24X28mm

made out of 0.33mm (Minimum) sheet spaced 1200mm along spaced

between main ‘T’ at 600mm centre to centre to form agrid of 1200X600mm

and secondary cross ’T’ of length 600mm and size 24x28mm made of

mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm

panel to form grid of size 600X600mm resting on periphery walls/partitions

on a perimeter wall angle pre coated steel of size (24X24X3000mm made of

0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre

to centre with 25mm long dry wall screws @ 230mm interval and laying

15mm thick Densified edges light weight calcium silicate ceiling tiles of

approved texture (Fine Fissured/Cosmos/Spintone) in the grid including,

cutting /making opening for services like diffusers, grills, light fittings, fixtures,

smoke detectors etc., wherever required, Main

9 Painting Two coats (excluding priming coat) on previously painted steel and 3.00 Sqmt 52.19

other metal surface with enamel paint, brushing to give an even shade

including cleaning the surface of all dirt, dust and other foreign matter.

10 Roller blinds 18.00 Sqmt 3585.50

Providing and supplying Roller Blinds assemblies are to be supplied &

installed in all windows with great precision. It should be water resistant and

fitted on aluminum head rails duly powder coated and fitted with stainless

steel drive rods. Manual operated and should have ISI mark. Complete or as

directed as per architect & engineer in charge.

11 Providing and fixing window having extruded aluminum Colour anodized 2.00 Sqmt 1713.70

section frame main outer size 63.50 x 38.10 x 1.95 mm,@ Wt 1.094 Kg /

Rmt, horizontal two track member size 61.85 mm x 31.75 mm x 1.20mm @

wt.of 0.695 Kg/mt, vertical member of size 61.85 mm x 31.75mm x 1.30 mm

@ wt.of 0.659 Kg/mt with sliding shutters of horizontal member size 40mm x

18mm x 1.29mm @ wt.of 0.456Kg/mt, vertical member of size 40mm x

18mm x 1.29mm @ wt.of 0.456Kg/mt, @ Wt. 0.457 Kg/mt with 5 mm thick

transparent bronze colour tinted float glass with powder coated aluminum

fittings and fixtures and transparent silicon sealant glass fixing to frame as

per details etc complete for window.

12 Providing and fixing FRP frame size 125x65 mm and 35mm thick FRP 7.98 Sqmt 2615.04

shutter having extra reinforcement on sides & edges in polish finish. The

core of the shutter & frame is to be filed up with injected polyurethene foam

done in situ alongwith embedded wooden pieces for stiffening & also taking

hinges & fintures. The whole FRP frame & shutter is to be water proof

weather proof, termite proof & resistance to mild acid/alkali. Rates are to be

inclusive of S.S hinges with necessary screws & alluminium S.S fixtures &

fastenings & fastener sleeve.

13 High back revolving & tilting executive chair(M39) Providing and supplying 4.00 Sqmt 16665.00

High back chair for conference with M.S frame work. Upholstered with

Artificial leather/Leatherette and molded PU foam, together with molded

seat & back covers. The back foam should be designed with contoured

lumber support for extra comfort. Caster of high durability & hydraulic. The

chair should have cylinder with 5 years warranty. The size of chair 53cm x

79cm (Back side) and 51cm x 49cm (seat size). The PU foam should be

molded with density =45 ± 2 kg/m3. with One-piece armrests. The

armrests are scratch and weather resistant. The permanent contact

mechanism is designed with 360° revolving type, 12º seat tilt 19° back tilt,

Front pivot for tilt with feet resting on ground ensuring more comfort, Tilt

tension adjestment, 5 position locking with anti-shock back mechanism,

which should prevent the backrest from impacting the user when the lock is

released, static seat depth adjustment=0.5 cm 5 position

14 Visitor Chairs (M39) 24.00 No 5555.00

Providing and supplying Visitor or Guest chair the seat & back are

made of 12mm thick hot-pressed plywood upholstered with changeable

fabric upholstery covers (as per requirement) and molded PU foam, together

with molded seat & back covers. The back foam should be designed with

contoured lumber support for extra comfort. The size of chair 45cm x

38cm (Back side) and 45cm x 43cm (seat size). The PU foam should

be molded with density =45 ± 2 kg/m3. The armrests with Leg made with

Powder coated MS structure as per architect selection. The Seat and back

fixed with MS structure with required necessary hardware.

15 Main Table with side unit 4.00 No 35855.00

Providing and supplying Main Table made with 19mm Thk. Plywood

(M1) structure as per architect drawing finished with 1.0 mm Thk.

decorative laminate (M24) on outside portion &0.8 mm Thk. liner

Laminate inside as specified & approved by architect fixed with

necessary fixtures and fastening (Hardware) (M14) as per architect

drawing. Provide Plastic Computer Desk Table Grommet Cable Wire

Outlet Hole Cover 60mm, Key-board trey, S.S. legs, Drawers with

telescopic roller channels (M15), Handle (M19) and locking (M16)

arrangements with all necessary fixtures and fastening (M14). Provide

Shutters as per drawing fixed with handle (M19), hinges (M18), magnet

(M14), complete with bidding patties and all required hardware (M14).

Provide footrest as per drawing. All exposed edges shall be covered with

required Teak wood beading Patti (M4) finished with approved melamine

polishing (M29) work. Complete as per architect's drawing and as per

instruction of architect & engineer in charge. (Refer drawing)

16 Two seated sofa 1.00 No 33330.00

Providing and supplying sofa(2seater) made with using 19mm Thk.

Plywood (M1) structure frame with S.S. legs required necessary support

fixed with necessary fixtures and fastening (Hardware)(M14). It shall

be covered with 32 Density PU foam(M22)with required Thickness as

per design in seat & back and handle portion this should be again

covered with 14 mm thick PU foam(M22) with Madarpat cover on it

& upholstered fabric(M26) or leather of suggested & approved by

architect finished with seat, back & all visible side as per architect drawing.

Complete as per architect's drawing and as per instruction of architect

& engineer in charge. (Refer drawing)

17 Three seated sofa 1.00 Sq.Mt. 32926.00

Providing and supplying sofa. (3 seated) made with using 19mm Thk.

Plywood (M1) structure frame with S.S. legs required necessary

support fixed with necessary fixtures and fastening (Hardware)(M14). It

shall be covered with 32 Density PU foam(M22) with required Thickness as

per design in seat & back and handle portion this should be again covered

with 14 mm thick PU foam(M22) with Madarpat cover on it &

upholstered fabric(M26) or leather of suggested & approved by architect

finished with seat, back & all visible side as per architect drawing.

Complete as per architect's drawing and as per instruction of architect &

engineer in charge. (Refer drawing)

18 Medium back revolving & tilting chair(M39) 5.00 No 13635.00

Providing and supplying Medium back chair for conference with M.S

frame work. Upholstered with changeable fabric upholstery covers

(as per requirement) and molded PU foam, together with molded seat &

back covers. The back foam should be designed with contoured lumber

support for extra comfort. Caster of high durability & hydraulic. The

chair should have cylinder with 5 years warranty. The size of chair

47.5cm x 58cm (Back side) and 49cm x 48cm (seat size). The PU foam

should be molded with density =45 ± 2 kg/m3 with One-piece armrests. The

armrests are scratch and weather resistant. The permanent contact

mechanisms are designed with 360° revolving type, with pneumatic

height adjustment & 17 ° maximum tilt only & tilt tension adjustment facility.

19 Applying two coats of (white cement based) or (acrylic lappy (putty)) and 81.00 Sq.Mt. 40.59

two coats of primer of approved brand and manufacture on new wall surface

to give an even shade including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand papered smooth.

20 Wall painting (Two coats) with plastic emulsion paint of approved brand and 76.00 Sq.Mt. 80.35

manufacture on undecorated wall surface to give an even shade including

throughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth.

21 Excavation for foundation upto1.50 MT depth including sorting out and 162.20 Cu.Mt 117.08

stacking of useful materials and disposing the excavated stuff up to 50 mt

lead ( A ) loose or Soft Soil

22 Excavation for foundation from 1.50 to 3.00 mt depth including sorting out 21.60 Cu.Mt 162.37

and stacking of useful materials and disposing the excavated stuff up to

mt lead ( B ) Dence and Hard Soil

23 Providing and laying controlled cement concrete M-150 and curing complete 6.12 Cu.Mt 3894.06

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in (a) Foundations, footings Bases of columns and

the like and Mass concrete.

24 Providing and laying controlled cement concrete M-250 and curing complete 5.20 Cu.Mt 4503.59

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in : (a) Foundations, footings

Bases of columns and the like and Mass concrete.

25 Providing and laying controlled cement concrete M-250 and curing complete 2.06 Cu.Mt 7724.48

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in :(d) Columns, pillars, posts and struts up to floor

two level. Up to Ground level

26 Providing and laying cement concrete 1:4:8 (1cement : 4 coarse sand : 8 0.83 Cu.Mt 2660.45

hand broken stone aggregates 40 mm. nominal size) and curing complete

excluding cost of from work in :(a) Foundation and plinth

27 Providing and laying controlled cement concrete M.200 and curing complete 5.84 Cu.Mt 5770.13

including the cost of formwork and reinforcement for reinforced concrete

work in (A) Foundations, footings, Base of columns and Mass concrete

28 Providing and laying controlled cement concrete M-250 and curing complete 2.25 Cu.Mt 5308.56

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in :(c) Beams, girders and cantilever up to floor For

29 Brick Work using Fly ash bricks having crushing strength not less than 70 1.27 Cu.Mt 4392.49

Kg/sm. In foundation and plinth cement mortar 1:6 (1 cement : 6 fine sand)

30 Providing and Laying Brick work using Fly Ash bricks having crushing 11.50 Cu.Mt 4348.45

strength not less than 70 Kg./Sq.cm.. In super structure above plinth

level up to floor two level in cement mortar 1:6 (1cement : 6 fine sand) (b)

Conventional Ground Floor

31 Providing and Laying Controlled Cement Concrete M-200 and curing etc. 3.42 Cu.Mt 6194.33

Complete including the cost of form work and excluding the cost of

reinforcement etc complete in slabs for all thickness over ground floor.

32 Providing and laying Controlled Cement Concrete M 200 for R.C.C. Lintel 0.10 Cu.Mt 7305.33

and curing complete Including the cost of formwork But Excluding the cost of

reinforcement for reinforced concrete work in Lintel Upto Floor Two level

etc. Complete ForGround Floor.

33 Providing and laying controlled cement concrete M-200 and curing complete 0.34 Cu.Mt 6290.28

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in chhaja up to floor two level. for Ground floor

34 Providing T M T. bar reinforcement of Fe-500-D for R.C.C.work including 3729.00 Kgs 76.21

bending binding and placing in position complete for G.F.

35 Providing 15 mm thick cement plaster in single coat on brick / concrete wall 130.00 Sq.Mt. 236.62

for interior plastering finished even and smooth ( i ) Cement mortar 1:4 ( 1-

cement :4 sand ),Including finishing with floating coat of neat cement slurry

etc. complete. For Ground Floor

36 Providing and fixing standard extuded of alluminium section of size 63 mm x 1.72 Sq.Mt. 1175.55

38.10 mm x 1.2 mm ( Jindal Section 2434, @ wt. 0.643kgh per mt ) with

colour anodized alluminium frame for ventilation with 5 mm thick frosted

glass as details etc. complete for ventilation

37 Providing 10 mm thick Smooth cement plaster in single coat on 10.60 Sq.Mt. 177.06

brick/concrete wall for interior plastering finished even and smooth (ii)

cement mortar 1:3 ( 1 cement : 3 sand) Including finishing with floating coat

of neat cement slurry etc. complete. For Ground Floor

38 Providing and laying 24" x 24" Vitrified 8 mm thick tiles flooring Combination 10.60 Sq.Mt. 1397.82

Dark & light shed of Anti - skid ( soluble Salt ) over over 20 mm (average)

base if cement mortar 1:6 (1cement : 6 coarse sand) on new surfrace by

adhesive material including jncluding providing 3mm thick horizontal &

vertical groove jointed with golden epoxy grouting and cleaning the surface

etc complete shade and pattern as approved by Engineer in charge. full body

39 Providing and laying coloured glazed tiles of the size 24"X24",300 mm x 200 46.42 Sq.Mt. 1441.21

mm x 8 mm / 300 mm x 450 mm x 8 mm in skirting, risers of steps and dedo

on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with

white cement slurry.

40 Providing and fixing machine cut free edges with rounded moulding machine 8.40 Sq.Mt. 2425.01

cut machine polished 18 mm thick Granite stone in single piece (Max

cm) Laid over 20 mm. (average thick base of cement mortar 1:6 (1 cement :

6 coarse sand ) and laid over and jointed with White cement slurry including

rubbing and polishing and making 3 nos of groove along longitudinal

directons etc. complete. 18 mm thick

41 Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete 980.00 Sq.Mt. 686.90

block 60mm thick with grade of concrete M300 pnumatic compressed /

vibrated mechanically and as per approved design Confirming to IS 15658 :

2006 including 35 mm Sand layer for levelling and filling the joint with sand in

proper line and level as per guidlines of IRC : SP 63-2018 etc. Complete.

42 Providing and laying water proofing treatment with china mosaic tiles 27.38 Sq.Mt. 1024.14

flooring over avg 40 mm C.C. 1:2:4 bedding for maintaining slope for plain

and curve surface & 12 mm to 20 mm of broken piece of ceramic / glazed

tiles ( one for more color as directed ) to be laid over cement mortar bedding

of C M 1:3 (1 cement : 3 sand ) containing one Kg of water proofing materials

per bag of O P C at plain or / and slops and to be tempered to bring mortar

ceramic up to surface with using white cement and colour pigment including

rounding of junctions and extending them up to 15 cm along the wall and

curing with bends any patterns or design as per drawing and cleaning by

using oxalic acid etc complete.

43 Provisding laying and jointing in true line and level 40mm dia U.P.V.C. pipe ( 57.20 Rmt 148.11

Sch-40) including fitting of Prince / Supreme / Astral / Finolex or eqivalent

make or as approved by engineer in charge. Pipe shall be fixed on the wall

the help of clamp at every two meter C/C or shall be concelled as directed

including nevessary fittings etc. including testing of pipe and joints and fixing

the same with adhasive solvent, including cost of all mayerials.

44 Provisding laying and jointing in true line and level 25mm dia U.P.V.C. pipe ( 34.00 Rmt 91.83

Sch-40) including fitting of Prince / Supreme / Astral / Finolex or eqivalent

make or as approved by engineer in charge. Pipe shall be fixed on the wall

the help of clamp at every two meter C/C or shall be concelled as directed

including nevessary fittings etc. including testing of pipe and joints and fixing

the same with adhasive solvent, including cost of all mayerials.

45 Provisding laying and jointing in true line and level 15mm dia U.P.V.C. pipe ( 66.00 Rmt 72.64

Sch-40) including fitting of Prince / Supreme / Astral / Finolex or eqivalent

make or as approved by engineer in charge. Pipe shall be fixed on the wall

the help of clamp at every two meter C/C or shall be concelled as directed

including nevessary fittings etc. including testing of pipe and joints and fixing

the same with adhasive solvent, including cost of all mayerials

46 Providing and fixing Wash down Water closet European type W.C. pan with 2.00 No 2414.91

integral P or S trap including jointing the trap with soil pipe in cement mortar

1:1 (1 cement : 1 find sand) (A)Viterous china pattern - I (i)in colour

including Providing and fixing Jaquaer concealled push Flush coke,

including Providing and fixing plastic Jaquaer jet spray , including Providing

and fixing Jaquaer seat and cover for wash down water closet with C.P.

brass hinges and rubber buffer etc complete shade and pattern as approved

by Engineer in charge.

47 Providing and fixing wash basin with Pedastal with single hole for pillar tap 2.00 No 2168.47

with C.I. Or M.S. brackers painted white including cutting holes and making

good the same including Jaquaer pillar tap, Brass waste, Jaquaer stop cack

, Jaquaer bottle trap and M I fisher union fittings :(ii) Flat back wash basin

500mm x 400mm size including all necessary fittings etc complete shade

and pattern as approved by Engineer in charge.

48 Providing and fixing Urinal or approved quality including conecting the Urinal 1.00 No 1036.27

with waste pipe , tap etc. complete.(A) White earthenware flat back or corner

type size 430mm x 260mm x 350mm

49 Providing and fixing screw down bib taps of following size :(B) Brass 16.00 No 186.82

chromium plated screw down bib tap(I) 15 mm dia.

50 Providing and fixing gun metal check or non return full way wheel valve (iii) 2.00 No 420.63

51 Providing and fixing gun metal check or non return full way wheel valve (E) 2.00 No 663.42

52 Providing and fixing cast iron (spun) nahni trap of the following nominal 8.00 No 606.08

diameter of self cleaning deign with C I screwed down of hinged gratting

including cost of cutting and making good the walls and floors 100 mm inlet

and 50 mm out let etc complete

53 Providing and fixing S.W. Gully trap with C I gratting brick masonary 5.00 No 1246.92

chamber and water tight C I cover with frame of 300 x 300 mm size (inside)

with standard weight (i)squremouth traps(C) 150 mm x 100 mm size P or R

54 Providing and fixing C.P. brass towel rail complete with C.P. Brass brackets 3.00 No 603.19

fixed to wooden plugs with C.P. Brass screws,(B) 600mm x 20 mm size

55 Providing and fixing 600mmX450mm Bevelled edge glass mirror of superior 3.00 No 833.73

glass mounted on 6mm th A.C. sheet or plywood sheet & fixed to wooden

plugs with C.P.brass screws and washers.

56 Providing and fixing to wall ceiling and floor 10.0 kg/cm2 working pressure 21.00 Rmt 277.42

polythelene pipes of the following outside dia low density pipes complete

with special flage compression type complete with special flage compression

type fittings, wall clips etc.including making good the wall celling and floor. [F]

57 Providing and fixing to wall ceiling and floor 10.0 kg/cm2 working pressure 28.00 Rmt 336.23

polythelene pipes of the following outside dia low density pipes complete

with special flage compression type complete with special flage compression

type fittings, wall clips etc.including making good the wall celling and floor..

[G] 110 mm dia.

58 Providing and Fixing in position cowl vent to pipes ( ii) 100 mm 4.00 No 501.86

59 constructing brick masonary Chamber for underground C.I. inspection 4.00 No 2932.92

chamber and bends with brick having crushing strength not less than

35Kg/sm in cm 1:5 including FRP cover with frame midium duty for taking

load of 10 ton R.C.C. top slab (1:2:4) (1 cement 2 coarse sand 4 graded

stone aggregates 20 mm size)and foundation concrete 1:5:10 inside

plastering 15 mm thick with cement mortar 1:3 finishing smooth with a floting

coat of neat cement on walls and bed concrete etc comp (I) Inside

dimentions 455mm X 610mm X 450mm deep for single pipe line.

60 Providing and fixing P V C water tank with necessary G I fittings and over 5000.00 Lit. 3.95

flow pipe ball valve clamp nipple also including placing on tarrace as directed

61 Providing and laying (Two level or slopes) and jointing with stiff mixture or 44.00 Rmt 305.13

cement mortar in proportion 1:1, salt glazed stone ware pipes following

nominal intrnal diametre including testing of pipes and joints etc.

62 Finishing Wall with weather proof exterior emulsion paint on wall surface 96.00 Sq.Mt. 114.53

(two coats) (APEX type paint) of approved brand & manufacture to give

an required shape even shade after thoroughly brushing surface to

remove all dirt and remains of loose powdered materials etc comp. for all

63 Providinfg and fixing Safty grills of required pattern for windows/ Door using 14.40 Kgs 109.08

necessary M.S angle/ M.S pipe, M.S flats and other structural steel at

required spacing including cutting, welding and fabriction etc. including one

coat of primer of approved quality and two coats of oil painting as per detail

drawing etc complete.

64 Providing &laying ave. 200 mm thick M-250 grade of controlled cement 44.06 Cu.Mt 5815.58

concrete including dressing sub base providing and laying 200 micron thick

LDPE memberance over prepared sub base providing and mixing recron 3s

fiber at 875 gm/cmt. of concrete placing the concrete and leveling with

surface vibrator finishing the surface with power floater and trowel light

brooming on the surface as directed including Providing and filling exparsion

joint having size 20 mm x 115 mm & filling the expansion joint having size

mm x 20mm by using cloper -200 as per manufacturer's specification and

making construction joint having size 10 mm x 10mm by using concrete

cutter machine etc. complete.

65 Providing and fixing pre-cast concrete kerb stone of gray cement based 118.00 Rmt 361.64

concrete block 30cm length,30cm height and 15cm thick of M250 grade

concret as per approved design and including excavation for fixing in proper

line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc complete.

66 Providing, laying (to level or slopes) and jointing reinforced concrete Light 40.00 Rmt 649.92

duty non-pressure pipes I.S. class NP3 of the following internal diameter with

collars and butt ends prepared for collar joints including testing of joints

complete. (i) 300mm

67 Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6- 79.00 Cu.Mt 3005.76

machine cut stone aggregates 40 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth

68 Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4- 16.70 Cu.Mt 3683.34

graded stone aggregates 20 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth

69 Steel work, welded in built up sections framed work including cutting, 2364.00 Kgs 90.48

hoisting, fixing in position and applying a priming coat of read lead paint &

two coat oil paint. (A)In beams and joists, channels angles Tees, flats, with

connecting plates or angle cleats as in main and cross beams. Hip and jack

rafters, purlins conneted to common rafters and the like..

70 Providing and fixing of Ridge flashing for roof panel shall be made out of 0.5 75.00 Kgs 858.67

mm thick pre coated GI sheet . The Precoated sheet shall be of minimum

240 mpa steel grade confirming to IS 14246:1995 and shall have zinc

coating of minimum 120 gsm as per IS:277:1992 , 5-7 microns epoxy primer

on both side of the sheet and polyester top coat 15-18 micron. The PPGI

Sheet shall have plastic protective guard film of minimum 25 microns to

avoid scratches during transportation. The ridge shall be fixed to the steel

members by pop rivet or self drilling/self stitching fastners @ maximum

mm c/c along length of capping/flashing etc complete .

71 Anti-Termite System:Providing and laying of permanent piping technology 3.00 Sq.Mt. 134.33

anti-termite treatment before flooring work by installing LLDP (Low linear

density polyethylene) tube of 8 mm O.D. & 6.4 mm 1.D. with inbuilt pressure

compensation chip every 30 cm interval in the tube, having working pressure

of 2 Kg/cm2 and release rate of 1.9 Itr/hour fixed by P-clips and nails. The

LLDP pipe shall be installed at the entire periphery of the building and at

internal network of building at a depth of 20 to 200 mm under floor at every

to 3 mtr. c/c distance (adjusted as per building layout ) & Ends of loop pass

through a PVC elbow of minimum 32 mm ID at junction box of wall and floor

level, entering into a steel reinforced grooved flexible pipe of minimum

mm ID leading into junction box and the loops shall terminate in junction

boxes & test every junction during injecting chemicals for termite control

treatment. The anti termite chemical Imidacloprid 30.5% SC mix as per IS-

6313 (part III) shall be injected by the pressure pump diluted with water @

10.5 ml/5 ltr of water at the rate of 2 Kg/sq.cm @ 5 Ltr/SMT. The contractor

shall submit approved line plan for piping system and junction boxes dully

approved by Engineer-in-Charge with bond of 5 year warranty.(i)Anti Termite

chemical injected area (Chemical injecting incl. labour cost)

72 Removing dry or oil bound distemper by a washing and scraping and sand 6.00 No 11.30

papering the wall surface smooth including necessary repairs to scratches

73 Dismantling sanitary fittings like wash basin . W.C. pan Indian and European 2.00 No 405.65

type, flushing tank etc. including stacking the materials with all lead and lift

74 Dismentling doors, windows, ventilators etc. (wood or steel) shutters 2.00 No 187.71

including chowkhats architraves, holdfasts and other attachment etc.

complete and stacking them within all lead and lift.(i) Not exceeding 3 Sq.M.

75 Providing and laying antiskid ceramic tiles 30 x 30 cm size 6 mm thick in 3.00 Sq.Mt. 970.07

flooring treads of steps and landing laid on a bed of 12 mm thick cement

mortar 1:3(1-cement:3-coarse sand)finishing with flush pointing in white

76 Providing 10mm thick cement plaster in single coat onbrick/concrete walls for 3.00 Sq.Mt. 128.86

interior plastering upto floor two level and finished even and smooth in

(i)Cement mortar 1:3 (1-cement:3-sand)

77 Providing 15mm thick cement plaster in single coat on Rough (Similar)side of 19.50 Sq.Mt. 171.80

single or half brick walls for interior plastering upto floor two level and

finished even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand)

78 Wall painting (two coats) with plastic emulsion paint of approved brand and 5.00 Sq.Mt. 52.19

manufacture on undecorated wall surface to give an even shade including

throughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth.

79 Painting (two coats) with plastic emulsion paint of approved brand and 3.00 Sq.Mt. 85.76

manufacture on undecorated ceiling surface to give an even shade including

throughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth.

80 Providing Water proofing Treatment on Sunk Slab including cement concrete 3.00 Sq.Mt. 340.88

flooring 1:2:4 (1-cement : 2-coarse sand : 4-graded stone aggregate 20mm

nominal size) laid in one layer and finished with a floating coat of neat

cement average 50mm thick to Prepare slope including water proofing

chemical etc. Complete for Sunk Slab All Floor. .

81 Providing and fixing mirror polished 18 mm thick Green Marble stone with full 4.00 Sq.Mt. 2004.85

round edge and polished of approved quality in clading on sill and around

the doors/ windows/ ventilation with 12 mm thick cement mortor CM (1:4) and

fixing with cement slurry & adhesive including moulding of exposed edges as

directed by engineering in charge etc. complete.

82 Providing and fixing FRP frame size 100 x 50 mm and 35 mm thick ( Fiber 1.60 Sq.Mt. 2372.49

Glass with PUF Injection ) FRP depress panel Single or Double shutter

having extra reinforcement on sides & edges in Gel coat finish.The core of

the both shutter & frame is to be filed up with injected fire retradat grade

polyurethene foam done in situ along with embeded wooden pieces for

stiffening & also taking hinges & fintures.The whole FRP frame & single or

double shutter is to be waterproof, weatherproof, termite proof & resistance

to mild acid/alkali. Rates are to be inclusive of S.S hinges with necessary

screws & alluminum fixtures & fastenings & fartener sleeve.Colour and

Shade approved by Engineer-In-Charge.

83 Providing, laying and jointing in true line and level 110 diametre U.P.V.C 20.00 Rmt 836.73

(Type B) conforming to IS 13592-1992 with one end plain and other end

socketed with rubber ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of

the size 110 mm diametre x 149 mm length x 145 mm heigh at every

mm center to center or shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all

84 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm 1.00 No 571.08

diameter with jali of the following nominal diameter of self cleansing design

with C.I scread down or hinged grating including the cost of cutting and

making good the walls.

85 Providing and fixing wash down water closet (European type W C pan) with 1.00 No 3001.72

integral P and S trap including jointing the trap with soil pipe in cement

mortar 1:1 (1 cement five sand) including providing and fixing plastic seat

cover for wash down WC with CP brass hinges and rubber buffers back

plastic seat and including providing and fixing PVC flushing tank with a pair

of C I or MS bracket with complete fitting such as lead valve siphon 15 mm

dia brass ball valve with polythene float CP brass handle unions and

couplings for connection with inlet out let and over flow pipes 40 mm dia

porcelain enameled flush bend including cutting holes in walls and making

good the same connection the flush bend with cistern and closet vitreous

86 Providing and fixing brass screw down stop tap.(A) 15mm dia. 1.00 No 205.83

87 Providing and fixing ball cock of approved. quality as directed.(A) Copper 1.00 No 189.84

Metal (ii) 50mm dia.

88 Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. 1.00 No 1670.26

brackets painted white including Rubber plug, sutting holes and making good

the same but excluding fittings and also including rate of C.P. brass waste

for washbasin or sink (A) 32mm dia. and M.I. fisher union for washbasin or

sink. (A) 32mm dia.; (A) Vitreous China:(ii) Flat Back washbasin 550 mm x v

400mm size. (i) In white colour.

89 Providing and fixing screw down bib taps of following size.(A) Brass screw 1.00 No 214.81

down bib tap polished bright. (i) 20mm dia.

90 Providing and fixing pillar tap, capstan head, screw down high pressure with 1.00 No 308.73

screws, shanks and back nuts. (i) 15mm dia.

91 Providing and fixing chromium plated brass half trun flush cock of approved 1.00 No 263.77

quality including fixing in pipe line etc. complete (ii) 25mm dia.

92 Constructing brick masonry chamber for underground C.I. Inspection C.I. 3.00 No 3933.95

Inspection chamber and bends with briocks having croshing strength not less

than 35Kg. Cm2 in C.M. 1:5 precast RCC cover 500mmx 700mm intenal

dimensions with frame (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse

sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10

inside plaster 15mm thick with cement mortar 1:3 finished smooth with a

floating coat of neat cement on walls and bed concrete etc. complete (i)

Inside dimensions 500mmx 700mm and 450mm deep for single pipe line.

93 Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( 50.00 Rmt 195.67

SCH- 40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with adhesive solvent,

including cost of all materials.

Deputy Executive Engineer, Executive Engineer

Dharampur (R&B) Sub Division Valsad (R&B) Division

Dharampur Valsad

I/We am/are willing to carry out the work at ………………………………………………..% above/below (percent should be

written in figures and words) of the estimated rates mentioned above. Amount of my/our tender works out as under.

*Estimated amount *Estimated amount

Put to tender Rs…3655126.62 Put to tender Rs…3655126.62

Deduct ……. % below Rs……………… Add ……. % Avove Rs…………..….

Net Rs. ……………… Total Rs. ………….…

In words ………………….…………………… In words ………………….

*( please strike out whichever is not applicable)

An Amount of 0.00/- (Rupees ) shall be recovered from the 1st RA Bill of this work towards salvage value of dismentalled /

Diversion material likely to be available from dismentalling the Dismentaling of stone flooring irrespective of the

dismentalled quantity actuallly received on site.

All works shall be carried out as public works department Handbook and other

specification of Division or as directed.

All the columns in schedule should be filled in ink or ballpen and the total of the

entries in last column should be struck by the contractor under his signature.

Rate quated include clearance of site (Prior commencement of work and at its close)

in all respects and hold good for work under all conditions,site moisture, weather etc.

The Contractor shall exhibit a board with detailed specification and details of work

as directed by the Engineer-In-Charge for which no extra payment shall be made.

The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

GST and Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per

Govt. G.R.: PRC-10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in

S.O.R. therefore in R.C.C. items where there is a change as per actual mix design the cost

of difference of cement consumption have been deducted from the rate of original item at

the rate of input rate mentioned in all the tender.

To be continued on additional sheet,if found necessary.

Deputy Executive Engineer, Executive Engineer

Signature of the contractor Dharampur (R&B) Sub Division Valsad (R&B) Division

Dharampur Valsad