Special repairs to bldg Nos. B 06 to 10 and B 18 to 21 at Kutir Vihar Allenby lines under GE South Ambala Cantt

Amount

SCHEDULE A PART I (B/R WORKS)

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed.

Use and waste form work chulla hoods, chajjas, troughs and similar items including edges for fair finished surface of concrete, complete all as specified.

Material and labour for reinforced cement concrete (design mix) M-25 (using 20mm graded mechanically crushed stone aggregates) as in chajjas, roof projections, etc. complete all as specified and directed.

Dismantling of brick work or stone masonary, precast cement concrete walling built in cement mortar including all quoins, arches, pillars etc., complete all as specified and as directed.

Dismantling of brick or terracing tiles in single layer on roofs and removal from site, complete all as specified and as directed.

Material and labour 40 mm thick brick tiles laid on and including 15 mm thick bedding layer in cement mortar 1:6 and joints grouted flush in cement mortar (1:3) mixed with 5% crude oil by weight of cement, complete all as specified and directed and flush pointed in cement mortar (1:3), complete all as specified.

All as per ser item No. 1.06 here-in-above, but except tiles, complete all as specified.

Material and labour for water proofing treatment with following application over roofs surface complete, all as specified and as directed :- (i) Plain cement concrete 1:2:4 type B1, (using 20 mm graded stone aggregate) 50 mm thick as in levelling course,. and surfaces finished even and fair without using extra cement. (ii) Applying oil bound bituminous primer at the rate of 0.4 Litres/Sqm as per IS 3384-1986 on prepared surfaces of roof. Surface shall be kept free, till the primer is impregnated and the solvent oil in the primer get evaporated. (iii) Applying one coat of hot straight run bitumen grade 30/40 (Grade S-35) conforming to IS-73 at the rate of 1.2 Kg/Sqm. (iv) Laying 3mm thick APP polymeric water proofing membrane of weight not less than 3.6 Kg/Sqm, black finish reinforced with non woven polyster matt, wth a thermo fusible finish, torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturers instruction including preparation of surface. The water proofing treatment shall be carried out by the manufacturer or his authorised applicators in terms of clause 11.43 of MES Schedule Part-I (2009). Roof treatment work is to be carried out in clear and dry weather only. Contractor should provide covering to roof by polythene sheets during sudden rains in progress of work to avoid any seepage in building.Ponding test shall be carried out after roof treatment and shall be passed by GE.

Material and Labour for PCC (1:2:4) B-1 using 20 mm graded stone agg as in surface channel or drain including use of necessary from work for fair finished surface, complete all as specified and as directed.

Material and Labour extra for forming fair finished drain or channel upto 45cm inner girth in cement concrete, using extra cement, including forms, moulds , mitred /stopped ends etc., complete all as specified and as directed.

Material and labour for plain cement concrete 1:3:6 type C-2 (using 40 mm graded mechanically crushed stone aggregate), as in foundation, filling and mass concrete, complete all as specified and directed.

Material and Labour for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Material and labour for brick work with sub class ‘B’ bricks burnt, straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed.

Material and Labour for Brick work with sub class ‘B’ bricks (Except Bricks), straight or curved on plan exceeding 6 metre mean radius, built in cement mortar (1:6) complete all as specified and as directed. ( Note- The serviceable bricks obtained from Serial item No-1.04 will be used after removing motar, cleaning the bricks with water, etc.)

Supply and fixing IInd class (hollock) factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and as directed.

Supplying and Fixing for factory made 35mm thick, 2nd class HW, plain framed, panelled shutters (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

Taking down chowkats or frames with shutter area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , complete all as specified and as directed.

Taking down chowkats or frames with shutter area exceeding 1.50 Square metre and not exceeding 4.00 Square metre and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish, complete all as specified and as directed.

Taking down shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each, from chowkhat complete all as specified.

Supplying & Fixing for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening, complete, all as specified and as directed.

Supply and fixing factory made solid PVC moulded door designer shutter with wood free EPS 28-30 mm thick with 2, 4, or 6 raised panel design with 2mm thick pre laminated moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face fixed on frame, complete all as per manufacturer instructions, complete all as specified and as directed.

Supply and fixing Factory made pressed steel frames of size 125 x 60 mm for doors fabricated from 1.25 mm thick sheet, with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc. and one shop coat of priming including plain cement concrete 1:3:6 type C-0 (using 12.5 mm graded mechanically crushed stone aggregates) in filling of door frame complete all as specified and as directed.

Supply and fixing steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on CECZ Chandigarh drawing No.. TD-219(c) sheet 1/3 to 3/3 and TD-220(c) sheet 1/3 to 3/3 as applicable complete all as specified and as directed. Note: (i) For the purpose of measurement and payment double shutter with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill 10 mm square bar irrespective of whatever shown on drawing. (iii) Glazing, wire mesh and painting shall be measured and paid for separately.

Supply and fixing for aluminium anodized barrel tower bolt of extruded section 200mm long, ISI marked, complete all as specified and as directed.

Supply and fixing 200 mm mild steel barrel tower bolt, ISI marked, stove enameled black with bright bolt and fixed, complete all as specified and as directed.

Supply and fixing 250 mm mild steel sliding door bolt, ISI marked with hasp, staple (bolt type) , stove enameled black, with bright clamp bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple, complete all as specified and as directed.

Supply only mild steel butt hinge of 100mm length, cold rolled, medium weight, ISI marked complete all as specified and as directed.

Supply and fixing mild steel pressed handle, oval type, stove enameled black, 150mm long, complete all as specified and as directed.

Supply and fixing for ISI Marked 150 mm long, aluminium handle, cast type, anodized, complete all as specified and as directed.

Supply and fixing galvanized steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple and including fixing with beads supplied with joinery when fixed in panels of joinery, complete all as specified and as directed.

Supply and fixing in repair galvanized steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple and including fixing with beads supplied with joinery when fixed in panels of joinery, complete all as specified and as directed.

Material and Labour for dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish/ demolished material outside defence land, complete all as specified and as directed.

Material and labour for wire brushing and cleaning top surfaces of cement concrete/brick tiles incl roughening surfaces of old concrete by picking, sweeping and washing down with water to remove dust including brushing neat cement slurry @ 3.00 kg/Square metre complete all as specified and directed .

Material and labour for 50mm thick, PCC 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregate) as in plinth protection/PCC path, and paving, finished the surface even and smooth without using extra cement, joint filled with bitumen and sand mixture applied hot (area not exceeding 1.20 sqm ) , complete all as specified and as directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles (Square/rectangular) , area of each tiles exceeding 0.18 sqm and not exceeding 0.38 sqm and 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface over and including cement screed bed 15mm thick in cement mortar (1:4) , complete all as specified and as directed.

Material and labour for premium quality, joint free non skid coloured ceramic tiles, of same description and length as of floor tile but 150 mm height on vertical surfaces of walls including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match ,complete all as specified and as directed.

Material and labour for Endura Tiles (coloured), good grip series, of size, 300 x 300 x 10 mm thick, pattern as approved br EIC as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including cement screed bed 15mm thick in cement mortar (1:4) base, complete all as specified and as directed.

Material and labour for premium quality, glazed coloured ceramic tiles 450 x 300 x 7mm thick on vertical surfaces of walls over and including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match, complete all as specified and as directed.

Material and labour for 18-20mm thick granite (of any type) ,machine cut and machine polished, and moulded on edges as in steps, jambs, pillar, counter WHB, floor, etc over and including 10mm thick in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and jointed with grey cement slurry , complete all as specified.

Material and Labour for taking down cement or cement lime plaster of any description on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc, complete all as specified and as directed.

Material and labour for 15mm thick rendering in cement mortar (1:6) on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement complete all as specified and as directed.

Material and Labour for 15mm thick rendering on surface of any description of brick work, concrete surfaces in cement mortar 1:4 mixed with WPC @2% by weight of cement or as per manufacturer’s instructions, finished even and fair, complete all as specified and as directed. (Note : WPC shall be measured and paid separately)

Supply only integral water proofing compound, complete all as specified and as directed.

Supplying and fixing for 25 mm dia 1.6 mm thick MS powder coated conduit decorated type curtain rod incl pair of MS bracket,finials (latto)/wall end socket at ends including fixing on wall with screws, complete all as specified and as directed.

Material and labour for preparation of old treated surfaces (Plastered or un-plastered) of ceilings, etc. by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of white wash, complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces of wall and applying two coats of interior emulsion with hand roller, over a coat of primer over 2-3mm thick wall care putty complete, all as specified and as directed.

Material and labour for two coats of cement base paint over a coat of primer over newly plastered surface including preparation of surface complete all as specified and as directed.

Material and labour for preparing new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Material and labour for two coats of synthetic enamel paint on steel surfaces over a coat of red oxide primer including preparation of new steel/pre primed surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified and as directed.

Supply and fixing in repair, water storage tank 500 ltr capacity HDPE triple layer, white coloured, conforming to IS , fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore,including taking down the unserviceable water tank and removing from site, complete all as specified and as directed.

Supply and fixing (in repair) , stainless steel openable, gratings , 75 mm dia , with and without hole for inserting PVC waste pipe complete all as specified.

Supply and fixing in repair, vitreous china wash hand basin, Coloured flat back of size 550x440mm excluding CI brackets but including PVC waste pipe, PVC connections and chromium plated waste coupling, etc.,complete all as specified and as directed.

Supply and fixed (in repairs) vitreous China coloured squatting pan of Orissa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including making good to floor surface with the existing surface and connection to flush pipe complete all as specified and as directed.

Supply and fixing 10 litre capacity virgin polypropylene cistern, ISI marked, coloured at low level complete with PVC bend/flush pipe and making all connection including taking down existing high or low level unserviceable flushing cistern and making good the disturbed surface to match with the existing surface complete all as specified and as directed.

Cutting chases,pinning inmaking good to facings where required and pointed in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc . cutting not exceeding 10cm girth in brick and making good in cement mortar 1:3 complete all as specified and as directed.

Taking up or down steel tubing and connections for 15mm dia including cleaning for refixing or removal to store , complete all as specified and as directed.

Taking up or down steel tubing and connections for 20mm dia including cleaning for refixing or removal to store , complete all as specified and as directed.

Refixing steel water tubing of 15 mm bore in new or old position with all new fittings as required, laids in floor , wall and on ceiling, complete all as specified and directed.

Refixing steel water tubing of 20 mm bore in new or old position with all new fittings as required, laids in floor , wall and on ceiling, complete all as specified and directed.

Supply and fixing steel water tubing of 15 mm bore, medium grade galvanized , laid in floor , wall and on ceiling, complete all as specified and as directed.

Supply and fixing steel water tubing of 20 mm bore, medium grade galvanized , laid in floor , wall and on ceiling, complete all as specified and as directed.

Supplying and fixing (in repair), bib tap screwed down high pressure, cast copper alloy,fancy type, chromium plated, ISI marked, with capstan heads, screwed down suitable for 15mm bore pipe or union, complete all as specified and as directed. (Make :PRIMA cat Part No PSP-501 or ESSCO Cat No-DLX-511 or Prayag Cat No. 8608 or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and fixing (in repair), angle cock, 15 mm dia , brass, chromium plated, ISI marked, screwed down, high pressure with capstain head screwed both ends for iron pipes or for unions, complete all as specified and as directed. (Make : PRIMA cat Part No PSP-504 or Cat No-SQT-526KN of ESSCO or Cat No. PIS-10 of Prayag or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supply and fixing in repair stainless steel sink 1.00mm thick, ISI marked for kitchen with plug, waste PVC pipe, washers including cantilever cast iron brackets connecting union waste pipe with drainage board over all size 940 mm x 460 mm with bowl size 405 mm x 354mm x 203 mm etc, complete all as specified and as directed. (Make :PRAYAG Cat No-1240-D (Solitaire Range) or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying & Fixing in repair for stainless steel plate rack standard size 900mmx 900mm x 200mm complete and fixing with rawl plug and steel screws of wt not less than 10 kg each, complete, all as specified and as directed. (Make : Prayag Cat No. or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and fixing (in repair), shower arm 240 mm long, light weight , round shape for wall mounted showers with wall flange suitable for 15mm bore pipe including overhead shower rose 125mm dia round shape single flow, complete all as specified and as directed. (Make : Cat No. BS-76 of Prayag or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and Fixing for brass tubular towel rail (finish Glossy), 20mm dia, D type, 60cm long between flanges, complete all as specified and as directed. (Make : ESSCO Cat No-1111 or Prayag Cat No. BA-20 or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge guarentee certificate for tubular towel rail from manufacturer before claiming payment.

Supply and fixing ,gun metal globe or gate valve with iron wheel head, 20mm dia, screwed both ends for iron pipes or unions, complete all as specified.

Supply and fixing ,gun metal globe or gate valve with iron wheel head, 15mm dia, screwed both ends for iron pipes or unions, complete all as specified.

Supply and fixed in repair, stop valves, 15 mm dia pipe, chromium plated, fancy type, ISI marked, screwed down, high pressure with capstain head, (concealed type) with sliding flange, screwed both ends for 15mm bore pipes or for unions, complete all as specified and as directed. Make- PRIMA Cat No PSP-507 or equivalent model in makes mentioned in Appendix 'B' of tender document. Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment.

Supply and fixing in repairs, chromium plated soap dish with fitting complete all as specifiedand directed. Make- PRIMA Cat Part No: PDX4501-C or equivalent make as per App 'B'of tender document.

Supplying and fixing (in repair),15mm bore pillar tap,chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ complete all as specified and as directed. (Make : ESSCO Cat No-DLX-507 or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supply and fixing PVC connections 450 mm long and 15mm dia with brass nuts and PVC washers on both ends, complete all as specified and as directed.

Demolition and breaking up drain pipes 75/100/110 mm dia, SGSW, AC, PVC, concrete pipe including fittings complete, all as specified and as directed.

Material and labour for hacking out old broken glass any thickness, size, quality or description from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads and removal the glass/ demolished material outside defence land, complete all as specified and as directed.

Supply and fixing, sheet glass 3mm thick, ordinary quality , in square not exceeding 0.5 Square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed.

Supply and fixing 75 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified and as directed. (Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534)

Supply and fixing 110 mm bore UPVC (SWR), vent cowls including jointing with solvent cement, complete all as specified and as directed.

Supply and fixing 110mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches or in floors, complete all as specified and as directed.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 110mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 75mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches or in floors, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall confirm be to IS 5382-1985)

Supply and fixing in repair, 110 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified and as directed. (Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534)

Supply and fixing in repair, PVC floor trap, 100mm size, with CP grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 including taking down of existing unservicable floor trap of any type and pattern complete all as specified and directed.

Supply and fixing 110 mm bore UPVC (SWR), junction single T (equal or unequal) with access door including jointing with solvent cement, complete all as specified.

Supply and fixing mild steel helical door spring 150 mm long fixed with screws to wooden chowkhats or welding to steel chowkhats, complete all as specified and as directed.

Demolition of concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) including floor tiles, screed bed etc including removal the rubbish/ demolished material outside defence land complete, all as specified and as directed.

Supply and fixing welded steel wire fabric/welded wire mesh fabric of size not less than 75mmx 50mm x3.15mm and weight not less than 3.53 Kg/Sqm and fixed in position complete, all as specified and as directed.

Material and labour for preparation of old steel surfaces, of any description not otherwise described, over 10 cm width or girth and applying one coats of approved colour synthetic enamel paint complete all as specified and as directed.

Material and labour for rendering, 05 mm thick, in cement mortar 1:3, on ceiling, finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

Material and labour for complete removal of existing treatment from wall surfaces by using appropriate technique as approved by Engr-in-charge and applying two coats of interior emulsion with hand roller, over a coat of primer over 2-3mm thick wall care putty complete, all as specified and as directed.

Material and labour for two coats of cement base paint over old plastered wall surface including preparation of wall surface complete all as specified and as directed.

SCHEDULE A PART II (INTERNAL ELECTRIFICATION)

Taking down carefully copper/aluminum point wiring light/fan/sockets out let/power point complete (fittings such as switches, sockets, ceiling rose, pendent holders, light fittings etc. are to be measured separately) and/or drawing out from existing conduit/batten and making good disturbed surface of walls/floors/ceiling, complete all as specified and as directed.

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable HFFR/ZHFR(Zero Halogen Fire Retardant), 1100 volt grade with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 25 mm dia with accessories, concealed on wall/ceiling and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable HFFR/ZHFR, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick bakelite hylem sheet, ISI marked top cover extended up to 25 mm over sunken box for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light/fan point controlled by one switch. Note :- Switch, socket and fan regulators to be measured and paid for separately . PVC Conduit confirming to IS 9537 part I & III Note (All chases will be cut by chase cutter only)

Description all as per Srl item No.2.02 here in before but for socket outlet point 5 Amp on same board complete all as specified and as directed.

Description all as per Srl item No.2.02 here in before but for socket outlet point 5 Amp on Independent board complete all as specified and as directed.

Description all as per Srl item No.2.02 here in before but one bell point controlled by one bell push complete, all as specified and as directed.

All as per the description of Serial Item No 2.02 above, but with 2.50 Sq mm un-sheathed multistranded cable for one socket outlet 15 Amps independent including continuous copper earth wire, PVC insulated of 2.50 Sq mm size, complete, all as specified and directed by Engineer-in-Charge. (Switch, Socket shall be measured and paid separately)

Supply and fixing switch piano 5 Amps, flush type, single pole, one way, 230 volt , AC supply, ISI Marked, complete all as specified and as directed. Make: ANCHOR/ LEGRAND/ CONA/ SCHNEIDER

Supply and fixing socket outlet 5 pin 6 amps, 230 volt. flush type, ISI Marked complete all as specified and as directed. Make: ANCHOR/ LEGRAND/ CONA/ SCHNEIDER

Supply and fixing switch piano 15 Amps flush type one way 230 Volts, 50 Hz , AC supply, ISI Marked, complete all as specified and as directed. Make: ANCHOR/ LEGRAND/ CONA/ SCHNEIDER

Supply and fixing socket outlet 2 in 1, 6 pin 6 /16 Amp and multi pin flush type, complete all as specified and as directed. Make: ANCHOR/ LEGRAND/ CONA/ SCHNEIDER

Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal, ISI Marked complete all as specified and as directed.

Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings,complete all as specified and as directed. Make: ANCHOR/ LEGRAND/ CONA/ SCHNEIDER

Supply and fixing bell push, 6 Amps , flush type, 240V, 50 Hz supply, complete all as specified and as directed. Make: ANCHOR/ LEGRAND/ CONA/ SCHNEIDER

Supplying and fixing electric bell, AC, ding-dong type, 230 Volt, single pole, complete all as specified and as directed.

Supply and fixing fan regulator electronic step type(Socket type), 120 watt, 230 Volts, 50 Hz, AC supply suitable for ceiling fan any type/make/sweep complete all as specified and as directed.

Supplying and fixing in replacement surface mounting LED tube light battern fitting suitable for LED tube light 20 watt with all accessories internally prewired and including connecting up with three core copper conductor cable of size 0.50 sqmm from ceiling rose to connector block complete all as specified and as directed. Make : Crompton Cat Part No. DMLN1T8-16/20 or equivalent model in makes mentioned for Group 1 in Appendix 'B' of tender document .

Supplying and fixing in replacement LED energy saving luminaires 20 watt with aluminium heat dissipates and high frequency power factor suitable for surface mounting battern fitting complete all as specified and as directed. Make : Crompton Cat Part No.LTT8-20 or equivalent model in makes mentioned for Group 1 in Appendix 'B' of tender document .

Supplying and fixing in replacement LED mirror light fitting 05 Watt with lamp, high output PMMA diffuser for glare free light, complete with all accessories internally prewired and connecting up with core twisted flexible copper conductor cable with suitable size, complete all as specified and as directed. Make- CG Ct Pt No- CDL-05-CDL or equivalent model in makes mentioned in Appendix 'B' of tender document .

Supplying and fixing in replacementr, LED bulk head light fitting 1x10 watt with lamp holder(1x10W) ABS housing, IP65 and connecting up with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector of light complete all as specified and as directed. Make: Bajaj Cat Part No. BIBWP 10WLED or equivalent model in makes mentioned for Group 2 in Appendix 'B' of tender document .

Supplying and fixing in replacement single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complet with one single pole MCB 240 V, 20 amp, complete all as specified and as directed.

Supply and fixing in replacement LED Security light luminaire 25 watt LED, ENDURA CITYLINER PLATINIUM, pressure die- cast aluminium housing, heat resistant glass, IP 66 protection with minimum 30 Nos of LEDs luminaire incl lamp (25 watt LED) complete with all accessories internally pre wired and including connecting with 3 core copper conductor flexible cable from terminal box to the ceiling rose or connector of the light point, complete all as specified and as directed. Make: Havells Cat Part No. LHEWBP7PL6S025 or equivalent model in makes mentioned in Appendix 'B' of tender document .

Supply and fixing in replacement bracket for security light made up of 1.20m long GI pipe, 25mm dia light grade, bent to required length and fixed to wall with two clamps made of 20x3 mm mild steel flat iron, 15cm long, 4 Nos 8mm dia bolts with nuts complete all as specified and as directed.

Supply and fixing distribution board for Load line TPN, 4 ways, double door, 415 volts, with and including 200 amps rated bus bar, vertical type, IP 43 protection powder coated, suitable for MCCB as in incomer including provn of 01, 160 Amps, MCCB, 4 Pole and MCB's as out going with suitable size of MS cabinet 2mm thick and making all type of connections with suitable size of gland for incomer cable complete , concealed on the wall surface, making good the disturbed portion with adjoining surfaces to match with existing finish and taking down the existing DB's and MCB's any type complete all as specified and as directed.

Supply and fixing in replacement, MCB triple pole and neutral , 415 volts, 63 Amps, breaking capacity 10KA ,B curve, ISI marked, complete all as specified and as directed.

Supply and fixing in replacement, MCB single pole, 240 volts, 50Hz , breaking capacity 10KA, B curve 6 to 32 Amps, ISI marked, complete all as specified and as directed.

Supply and fixing MCB single pole and neutral, 240 volts, 50Hz , breaking capacity 10KA, B curve, 63 Amps, ISI marked, complete all as specified and as directed.

Supply and fixing isolator single pole and neutral, 240 volts, 50Hz , breaking capacity 10KA, B curve, 40 Amps, ISI marked, complete all as specified and as directed.

Supply, insatallation, testing of SPN distibution board 8 way, double door, IP 43 protection, as per IS 8623 including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles, concealed on the wall surface including taking down the existing DB's any type and description and making good the disturbed portion with adjoining surfaces to match with existing finish complete all as specified and as directed.

Material and labour for sub main wiring with two single core ZHFR (Zero Halogen fire Retardant), PVC insulated unsheathed copper conductor cable 4.00 sqmm drawn in and including rigid non metallic PVC medium grade 25 mm dia concealed conduit with accessories on wall or ceiling with one additional PVC insulated , stranded copper conductor ZHFR of 4.0 sqmm,green colour for earth continuity conductor including taking down old unserviceable sub main wiring and making good the disturbed portion with adjoining surfaces to match with existing finish complete, all as specified and directed. Note- i) Note- 2 run of 4 sqmm and 1 run of 4 sqmm cable with concealed conduct shall be measured as 1 unit. ii) All chases will be cut by chase cutter only.

Taking out old earthing complete and taking out old unserviceable earthing material and provision of new earthing complete with galvanised earth plate electrode 600mm x 600mmx 6mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m below ground level with top edge of the earth plate not less than 1.5m below normal ground level, connected to 4.00 mm GI wire earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire protected by galvanized steel pipe 15mm dia (light grade) and connected to main switch or main control board all as shown in electrical plate No.3 of SSR Part-I & including necessary excavation and earth work. The rate also include charcoal & salt in alternate layers, 20mm dia GI pipe (light grade) for watering, protection pipe, funnel, wire mesh, RCC cover etc. complete, all as specified or indicated including testing on completion. Note : The rates for earth work, GI protection pipe, funnel, wire wesh, RCC cover, etc shall be deemed to be including in quoted rates. RCC cover shall be 50mm thick in 1:2:4 type B-1 using 8mm bars @10cm c/c both way.

Supply and fixing 1100 volts grade heavy duty cable PVC insulated, aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections, suspended by insulating hangers not more than 1 metre apart, including 4mm dia, GI, suspension wire, one twin core cable flat or circular, stranded conductor 16 Sqmm complete all as specified and as directed.

Note:- Amount of credit of Rs. 40,699.00 for retrieved materials is mentioned in Schedule of Credit Page No. 106R & 107R of tender documents in pdf form which will be deducted offline while acceptance of tender.

PARVEEN KUMAR

V K Constructive Builders

S M BUILDERS

M/S JAISANT CONSTRUCTION CO.

Ashwani Kumar

DUTT BUILDERS