Construction of Communitty hall at Chinnavadugapatty H/O Authur Poolampalayam

Name of the Work: Construction of Communitty hall at Chinnavadugapatty H/O Authur Poolampalayam

Earth work excavation for foundation in all clauses of soils and sub soils to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and boiling out water whenever necessary et complete complying with stand

Cement concrete 1:4:8 mix ( one cement four sand and eight aggregate)using 40mm gauge hand broken granite tone jelly for foundation including dewatering if found ecessary and laid in layers of not more than 15 cm thick and compacted,etc., complete comply

Supplying fabricating and placing in position of ribbed steel rods for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors etc., complete

Supplying and erecting centering for sides Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X

Below GL

Above GL

RCC 1: 1/2 :3 mix using 20 mm ISS HBG metal for RCC items of work excluding items of works excluding centering,shuttering, and ost of reinforcement grill ,out including curing etc complete and also including fixing fan clamps and ixtures in rcc works

Brick work in cm 1:5 mix(one cement and five sand) using country bricks ground maded of size 23 x 11 x 7 cm including curing,finishing and cost & Conveyance of all materials etc., complete.

Plastering surfaces of RCC items such as slabs,beams,sunshades with cement mortar 1:3 -10mm thick including packing, providing cement mortar beading for sunshades staircase ,steps, lands slabs etc.,as directed by departmental officers etc, complete

Plastering with cm 1:5 mix( one cement and five sand ) to 12 mm thick including cost and conveyance of all materials in all floors etc.,as directed by departmental officers etc, complete complying with standard specifications.

Fabricating Supply and fixing and position of MS Shutter with single leave. The door outer frame will be 40x40x6mm MS angle, the shutter frame will be 35x35x6 mm, MS angle intermediate stiffner will be 35x35x6 mm with cross stiffner 25x 25x5 mm flats covered

Fabricating Supply and fixing and position of MS Windows with two leave. The window outer frame will be 35x35x6mm MS angle, the shutter frame will be 25x25x6 mm, MS angle intermediate stiffner will be 25x25x6 mm with cross stiffner 25x 25x5 mm flats covered

Paving the floor with Vetrified tiles 0.60mx0.6mx0.008m in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement as

Distembering two coats of oil bound distember using one coat of primer coat including cost & conveyance to size and all labour charges etc., complete.

Painting two coats with ready mixed Exterior Emulsion paint of approved qualityand colour over a priming coat, including through scrapping,clean removel of dirt etc complete .

Painting two coats of new iron work with best quality synthetic enamel paint of approved quality and colour with priming coat including the cost all materials etc.,complete, in all floors.

Paving the floor with Anti skid step tiles 20mm Thick in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement as

Supplying and fixing following electrical arrangement

PVC light point / fan point SD 17

Plug point SD 36

Tube Light Fiittings (SD 87)

AC Ceiling fan (SD106)

Street light Fiittings (SD 94 )

3/20copper wire (SD 64)

7/20 GI Wire

20mm GI Service pipe (SD69)

GST Amount for providing Service to Government Contract Works for the above ConstructionWorks. GST Amount is the Total GST Amount for overall quoted amount above this row in column "BB" for all works in this package} (Refer Clause 13.2 & 13.3 of Section 2 of Instruction to Bidders (ITB) of SBD)

Please Enable Macros to View BoQ information