Protection of heritage of Tithal beach and historically important site for Valsad.Ta.Valsad Dist.Valsad under DGVCL CSR Initiative 2025-26

Name of work: Protection of heritage of Tithal beach and historically important site for Valsad.Ta.Valsad Dist.Valsad under

DGVCL CSR Initiative 2025-26.

Item of Work Quantity Unit Amount

1 Providing and fixing pre-cast Rubber Dye / steel Dye inter locking

concrete block 60mm thick with grade of concrete M300 pnumatic

compressed / vibrated mechanically and as per approved design

Confirming to IS 15658 : 2006 including 35 mm Sand layer for 10072.00 686.90 Sqmt

levelling and filling the joint with sand in proper line and level as

per guidlines of IRC : SP 63-2018 etc. Complete.

2 Providing and casting in situ ordinary cement concreteM-200

forKerbs/Kerb blocks including formwork, curingand finishing

complete. 89.00 4249.93 Cum.

3 20mm thick sand faced cement plaster on walls upto height

metres above ground level consisting of 12mm thick backing coat

of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of 2449.00 300.66 Sqmt

C.M. 1:1 (1-cement : 1-sand) etc. complete.

4 Finishing wall with weather proof exterior emulsion paint on wall

surface (two coats) to give an required shape even shade after

thoroughly brushing the surface to remove all dirt, and remains of 2449.00 114.53 Sqmt

loose powdered materials.etc complete

5 Providing and laying polished Kota stone slab flooringover 20mm

(Average) thick base of cement mortar 1:6(1-cement : 6-coarse

sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and

jointed with greycement slurry mixed with pigment to match the 1392.00 965.59 Sqmt

shade of slab including rubbing and polishing etc.complete.

6 Supplying and erecting Flexible PVC insulated multi strand multi

core 1.1 kv grade ISI marked copper wires of following size to be

erected as directed.(e) 1.50 Sq.mm 3 core round PVC sheathed

7 providing and erecting Approved make Four pole moulded case

circuit breaker having breaking capacity ICU of 25 KA. at

V,having normal current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on A.C. supply 50 c/s. 1 6173.12 Ea

with all internal connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing.ICS=100% of ICU only.Cat

8 providing and erecting Miniature circuit breaker single pole 0.5A to

2A system and having breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with ISI Mark Cat.III

9 Providing & erecting 415V MCB Four Pole Switch for Lighting Load

(B curve) having 10KA breaking capacity & confirms to IS :8828 in

existing box having following capacity (b)40 Amp. Cat.III

10 Providing and erecting HOT deep Galvanised iron strip wire 8 to

11 Providing and erecting Pipe type earthing having 150 cms.long and

2.5 cms. dia. galvanised iron pipe with coupling and buch buried in

specially prepared earth pit complete with necessary 8 SWG earth

12 For using salt and charcoal / coke as required for pipe type

13 Supplying & erecting earth pit of minimum bore dia.150mm size approved

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having

200-250 Micron galvanising, connection terminal dia of 12mm with constant

ohmic value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber and

heavy duty cover.(approved make OEM has to submit test certificate) &

having back filling compound of (B) Inner chemical (CCM Compound)- 1 4591.46 Ea

Resistivity:- 0.2 meter testing as per IEC 62561-2017, Voltage drop:- <

1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound

:- Earthing compound should be capable to retain moisture for long time

Necessary test report must be submitted. (a) For Electrical Installation up

to 440V in normal soil Length of pipe - 1 Mtr Back filling compound - 1 Nos

Item of Work Quantity Unit Amount

14 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on

wall with necessary clamps or in existing trench / pipe of following 878 140.39 Mtr

size of cables (C) 4 core 10 Sq. mm

15 Making trench in Hard Murrum / Tar Road of suitable width of

cm or required depth for laying any size of cable or locating the

fault all over the run and back filling the same and making the

surface as normal ground. (B) If additional machinery like hammer

driller or JCB use [Add]

16 Supplying following size of Light duty “A” Class G.I . Pipe &

erecting as directed by Engineer-in-charge. (B) 50 mm dia 10 300.98 Mtr

17 Providing & laying approved make ISI marked HDPE 6Kg / cm2

(Class-3) as per IS:4984:1995 PE-80 to be erected at road

crossing on or floor as directed for laying of cable. The pipes as 684 108.07 Mtr

following size of dia & weight per 6 mtr. (A) 40 mm inner Dia.

18 Providing and, fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables.(C) 2 to 4 114 38.38 Ea

19 Solder less crimping type Aluminium lugs conforming to IS suitable

for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut 456 13.13 Ea

bolts in an approved manner. (B) 10 Sq.mm

Item of Work Quantity Unit Amount

20 SITC of Decorative Post Top luminaire 40 watt BIS certified of same model

along with round shape and Top housing made of aluminium die cast and

spun aluminium ,Dia should be min 520 mm, along with a die cast

aluminium arm and total height should br min 370 mm. The luminaire must

have UV stabilized Polycarbonate protector providing high impact resistant

of not less than IK10. The body of fixture must have separate control gear

compartment and sealed optical compartment to achieve IP66 grade

protection and shall have provision of toolless access to control gear for

easy maintenance. The luminaire must be provided with Vent for optical

compartment for efficient pressure equalization. Each LED shall be provided

with a highly efficient lens for uniform photometric distribution. The

luminaire must be suspended in a hot dip galvanized pu painted Ring

Bracket with 1/2 inch BSP stainless steel pipe provided with 2 chuck

Overall luminous efficiency of luminaire shall be minimum 120 Lm/W at

correlated colour temperature (CCT) of 4000K colour rendering index

(CRI)>70 and residual flux of 70% (L70) @ 50,000 hours. The luminaire

shall have the photometry achieved as per IS Standards. The luminaire

should be deigned for Electrical Class I and must operate at any voltage

from 120V to 270V, with Power Factor ≥ 0.95 and shall be provided with

internal surge protection of minimum 4 kV and external surge protection of

10/10 kV (in both Common & Differential Modes). Luminaire is suitable for

operating temperature (Ta) from -10° to 40°C. The manufacturer must

have ISO 9001/14001/45001 and CE certification and the same shall be

attached alongwith tender submission. Kesslec VALE 40W.....

SITC of Supply of 4 Mtr height GI pu painted decorative pole having cast

iron decorative base and pipe dia of 114 mm OD & 1 mtr long with

decorative cast iron decorative reducer jointing with 76 mm OD straight

pipe (as per drawing). Pole shall be mounted on square steel base plate

250*250 *12 mm thickness suitable for mounting on 4 nos foundation 57 40400.00 Ea

bolts. The Pole Shaft should be fabricated out of Steel tube of grade YST

240 and batch test reports for chemical and mechanical properties of

material should be submitted along with the bid. Structurally designed base

plate of Steel A36/A572-50 or equivalent should be welded with the pole

shaft. The spigot shall be of 60mm dia suitable for vertical mount bracket

installation. The welding shall be of high quality, carried out by qualified

welders using approved welding procedures and tested for its quality

through NDT method, such as DP Test. The pole shall be provided with an

opening at the bottom with removable cover for providing connectors,

MCB, etc. (to be supplied by others)

Appropriate reinforcement shall be provided to compensate for the loss of

section at this point to ensure overall structural stability of the pole under

specified operating conditions. The pole shaft structure and bracket shall

be hot dip galvanized through single dip process as per ASTM A123 and

minimum average coating shall not be less than 65 microns. No mechanical

operation, such as welding, drilling, etc. should be carried out on the pole

structure Complete pole shall be treated with high quality primer and

thereafter coated with Marine grade Polyurethane paint. The painting shall

be carried out by experienced and trained technicians using proven and

established painting procedure. Only ‘controlled’ paint drying process shall

be used to ensure proper adhesion and finish of the paint. The decorative

pole shall be of ‘composite’ construction designed to withstand specified

‘dead load’ pertaining to the luminaire and its mounting accessories and

‘wind load’ corresponding to a IS 875 Part 3. The manufacturer must have

ISO 9001/14001/45001 and CE certification and the same shall be attached

alongwith tender submission. Kesslec BOSTON Pole Kesslec BOSTON Pole

4M with bracket - BOSTON POLE 4M HOT DIP GALVANIZED MARINE

GRADE WITH POST TOP VALE 40W 4000K [Design of Pole, Bracket &

Fitting to be approved by the Competent Authority]

21 Providing 1:2:4 cement concrete foundation & 70 % PCC from

bottom including excavation for the pole of size 45 x 45 x 100 cm.

Deep in below ground level with plinth of 45 cm x 45 cm (or 45 cm

dia x 45 cm) high upper ground level with necessary curing and 57 809.01 Ea

finishing in approved manner.

( for 4 & 6 mtr pole)

Item of Work Quantity Unit Amount

22 Excavating hard rock or bituminous road (B.T.) by chiselling or

using tool and tackles for preparing pit for poles or earth plates or

for laying pipes & clearing the site by removing debris & making 28.5 659.93 Cu.Mtr.

site good. [10 % additional for using machinery like driller as per

23 Supplying & erecting approved make IP 55 grade Company

fabricated Timer Panel of following capacity for switch On-Off

street lights on time scheduling basis made from 16G CRCA sheet

duly epoxy power painted inside and outside with hinged doors and

locking arrangement consisting of suitable size of 4 Pole MCB and

pole contactor (cat-III)with analog time switch, auto manual switch 13350.18 Ea

of same make and suitable input and output Bakelite terminals

and with door earthing approved by Engineer in charge. [B]

24 Misc.work/Unforseenworkifrequiredtobecarriedoutduring execution

of the work which are assential and required at stage of working

suchas Electricalwork, Furniturework, Landscaping work,

Plumbingwork, Flaseceiling work,colour work and misc. civil work

as per instruction of Engineer in charge.

Total Amount in Rs.

Total Amount in Rs.

Total Amount with GST in Rs.

Total Amount with GST in Rs.