58/EDCG/2025-26

Amount

SAFE LOADING CARRIAGE & UNLOADING OF FOLLOWING MATERIALS FROM CENTRE STORE, LAKHIMPUR TO DIFFERENT WORK SITES AND ITS STACKING DISTANCE APPROX (55-100) KMS

LINE MATERIAL

PCC POLE

STP POLE 11 MTR. LONG

T/F16/25/63 KVA

T/F100/250 KVA

T/F/400/630 KVA

ACSR RABIT/DOG/RACOON/WEASEL/CONDUCTOR

ABC (3X120/95/70/25/16) SQMM

11KV XLPE CABLE (3X35/70/120/185/240)

11 KV PILFER RESISTANT MATRIAL CUBICAL

11KV POLE MOUNTED CT/PT

DP BOX 1 PHASE / 3 PHASE

FABRICATION, ERECTION OF SUB-STATION TYPE DOUBLE POLE ON 8.5 MTR LONG PCC/11MTR LONG ST POLE ALONG WITH FIXING OF NECESSARY HARDWARE OF DOUBLE POLE ALONG WITH NECESSARY PIN INSULATOR AS PER RESSPO SPECIFICATION COMPLETE IN ALL RESPECT.

DRAGGING OF ST/PCC POLE TO PIT SITE DIGGING OF PIT ERECTION AND GROUTING (AS PER RESSPO NORMS) INCLUDING PROVIDING ALL DECENTRALISED MATERIAL REQUIRED FOR COMPLETION OF WORK . WORK IS TO BE CARRIED OUT AS PER RESSPO SPECIFICATION COMPLETE IN ALL RESPECT.

FABRICATION, ERECTION, T-OFF POLE SINGLE SECTION POLE ALONG WITH T-OFF CHANNEL CLAMP DISC FITTING & PIN ACCESSORIES, GROUNTING IN 1:4:8 CEMENT , BRICK BALLAST AND RIVER SAND AS PER RESSPO SPECIFIATION

GROUTING OF PCC/ST POLE WITH CEMENT, BRICKS BALLAT AND RIVER SAND RATIO 1:4:8

PROVIDING NUT BOLTS WASHERS OF DIFFERENT SIZES

ORDINARY EARTHING BY MS EARTH ROD 2500MM LONG AS PER RESSPO SCHEDULE. ONLY GI WIRE & EARTH ROD SHALL BE SUPPLIED BY THE DEPARTMENT

FABRICATION ERECTGION T-OFF POLE SINGLE SECTION POLE ALONGWITH T-OFF CHANNEL,CLAMP ,DISK FITTING AND PIN ACCESSORIES

GROUTING AND NUZZLING OF STAY SET COMPLETE INCLUDING ITS GROUTING BY CIVIL MATERIAL (CEMENT, BRICK BALLAST AND RIVER SAND ) ONLY STAY WIRE SHALL BE SUPPLIED BY THE DEPARTMENT

LAYING AND SAGGING OF 3 PHASE 3 WIRE 11KV LINE ON ACSR WEASE/RABBIT/RACCOON/DOG CONDUCTOR AS PER RESSPO SPECIFICATION AND DIRECTION OF E/I

PROVIDING AND FIXING OF GUARDING ANGLE ON EXISTING 11KV SUPPORT WITH CLAMP AND NUT BOLTS

CRADLE GUARDING IF HT LINE BY GI WIRE SHALL BE SUPPLIED BY THE DEPARTMENT

ERECTION & COMMISIONING OF AB CABLE (3X120/95/70/25/16SQ.MM)

LAYING OF CABLE 11KV XLPE CABLE (3X35/70/120/185/240) SQMM IN PAKKA ROAD BY BORING METHOD LAYING CABLE AS PER RESSPO SPECIFICATION & DIRECTION OF E/I

LAYING OF CABLE 11KV THROUGH PIPING

HOISTING OF 11KV XLPE CABLE WILL BE PASSED THROUGH MS PIPE OF REQUIRED SIZE DULY CLAMPED WITH POLE AT THE BOTTOM MIDDLE AND TOP OF THE POLE

SUPPLY AND FIXING OF 11KV CABLE JOINING KIT O/D AND I/D

INSTALLATION OF 11 KV CT/PT ON DOUBLE POLLE CONNECT WITH METERING UNIT ALONG WITH PROVIDING AND FIXING OF ALL REQUIRED ACCESSORIES SUCH AS S/S BASE, MS FLAT, CLAMPS NUT AND BOLTS JUMPERING AND COMMISIONING

CONSTRUCTION OF BRICK MASONRY PLINTH SUITABLE FOR INSTALLATION OF 11KV PILFER METERING CUBICAL ALONG WITH PLASTERING.

DRAGGING OF 11KV PILFER METERING CUBICAL INSIDE THE METERING ROOM, ITS INSTALLATION AND COMMISIONING.

FIXING OF 1 PHASE / 3 PHASE DISTRIBUTION BOX/ KIOSK ON THE LT POLES INCLUDING ALL CLAMPS AND METERIAL REQUIRED FOR MOUNTING CONNECTIONS AND SEALING.

HIGH PRESSURE TESTING OF 11 KV(3X35/70/12/185/240)XLPE ALONG WITH ARRANGEMENT OF HIGH PRESSURE EQUIPMENT.

PROVIDING OF HOLDING CLAMP FOR TOP DROPPER T/F

PROVIDING OF HOLDING CLAMP FOR PCC/STP POLES

PROVIDING OF F CLAMP FOR PCC /STP POLES

DRILLING CUTTING AND MAKING OF HOLE.

CUTTING AND CHOPPING OF TREE BRANCHES FOR CLEARENCE OF HT/LT LINE AFTER CLEARANCE LINE THROUGHOUT PIECES OF TREE BRANCHES OF SITE AS AND WHEN REQUIRED FOR COMPLETION OF WORK.

SAFE INSTALLATION & ENERGISATION OF 16/25/63 KVA T/F ON DOUBLE POLE BY PROVIDING AND FIXING OF L PIECE LUGS MAKING HT/LT CONNECTION AND ITS COMMISIONING ONLY TRANSFORMER SHALL BE SUPPLIED BY THE DEPARMENT.

SAFE INSTALLATION & ENERGISATION OF 100/250/400/630 KVA T/F ON PLINTH BY PROVIDING AND FIXING OF L PIECE LUGS MAKING HT/LT CONNECTION AND ITS COMMISIONING ONLY TRANSFORMER SHALL BE SUPPLIED BY THE DEPARMENT.

FIXING OF WELL TYPE EARTHING 01 NO NUTRAL BODY AND 01 NO BODY COMPLETE IN ALL RESPECT AS PER RESSPO SPECIFICATION.

CONSTRUCTION OF PLINTH 2 METER X 2 METER X 1.5 METER FOR 100/250/400/630 KVA. TRANSFORMER PLINTH WALL SHALL BE BRICK/ STONE MASONRY OF 230 MM THICK, OUTSIDE OF THE WALL TO BE PLASTERED WITH 18 MM THICK CEMENT MORTAR (1:3), INSIDE OF THE PLINTH SHALL BE FILLED WITH BORROWEDSAND DULY COMPACTED R.C.C. TOP SLAB (1:2:4) SHALL BE 75 MM THICK (CONSTRUCTION OF PLINTH SHOULD COMPLY WITH RESSPO NORMS)

PROPER WIRE MESH FENCING OF TRANSFORMER ALONGSIDE THE PLINTH. THE HEIGHT OF THE FENCE SHOULD BE 7 FEETS ABOVE FROM GROUND, PROVIDING FABRICATION AND FIXING THE MAIN GATE IN FRONT OF THE PLINTH WITH PROVISION FOR LOCKING SYSTEM. PAINTING OF ENTIRE METAL WORKS/ MAIN GATE WITH WIRE MESH WITH BUS GREEN SUPER ENAMELED PAINT IN TWO COATS ON THE PRIMER COAT OF RED OXIDE. COMPLETE IN ALL RESPECT

GST EXTRA

M/S NEW STAR TRADERS (BID ID -5764448)

M/S JAISWAL INTERPRISES (BID ID -5764625)