CMLRRP Amaravila Thamarapalli Road re tarring in Pullamala Ward re tender

Amount

Retarring

4.9 : Wet Mix Macadam <br> Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. <br> By Mechanical Means with 1 km lead

5.1.1a : Prime Coat :- Low porosity <br> Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

5.5.B.2a : Modified Penetration Macadam 75 mm thick using Bitumen S-65 <br> Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. <br> (B) 75 mm thick :- (II) Bitumen (S-65)

5.5.A.1a : Modified Penetration Macadam 50 mm thick using Bitumen S-65 <br> Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506.

5.2.1a : Tack Coat<br> Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

5.2.2a : Tack Coat <br>Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.9.2.2.Pa : Plastic Roads - Bitumen S-65 <br> 20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder <br> Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 (with 7% of bitumen replaced by shredded waste plastic) <br> Case - I By Manual Means <br> (II) Bitumen (S-65) (VG - 30)

5.12.A.3.2a : Seal Coat - Manual Means - Type C - Bitumen S-65 <br> Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 <br> A. By Manual Means :- Case - III : Type C <br> (II) Bitumen (S-65)

od891615/2020_2021 : Construction of un-reinforced dowel jointed at expansion and construction joint&lt;br&gt;only,plain cement concrete pavement ,thickness as per design,over a prepared sub base,with 43 grade&lt;br&gt;cement or any other type as per clause 1501.2.2 M 30 (grade),coarse and fine aggregates conforming to IS&lt;br&gt;383,maximum size of coarse aggregate not exceeding 25 mm,mixed in a concrete mixer of not less than 0.2&lt;br&gt;cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side&lt;br&gt;formwork(steel channel, laying and fixing of 125 micron thick polythene film, wedges,steel plates including&lt;br&gt;levelling the formwork as per drawing),spreading the concrete with showels,rakes,compacted using&lt;br&gt;needle,screed, and plate vibrators and finished in continuous operation including provision of contraction&lt;br&gt;and expansion ,construction joints,applying debonding strips, primer, sealant, dowel bars, near approaches&lt;br&gt;to bridge /culvert and construction joints, admixtures as approved,curing of concrete slabs for 14 days,using&lt;br&gt;curing compound(where specified) and water finishing to lines and grade as per drawing and Technical&lt;br&gt;Specifications clause 1501

od910960/2020_2021 : Construction of Embabkment with Material obtained from B ORROW PITS &lt;br&gt; construction of embankment with approved material obtained from borrow pts with a lift up to 1.5m transporting to site spreading grading to reguired slop and compacting to meet requirment of tables 300 1 and 300 2 with a lead up to 1000m as per technical specification clause 301.5

6.7.1 : Interlocking Concrete Block Pavement <br> Providing and Laying of Interlocking Concrete Block Pavements having thickness 80 mm as per drawings and Technical Specification Clause 1504.

51.2.3 : Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

od932699/2020_2021 : Supplying and fixing granite slab name board having size 90x60cm engraving it on the name of project including all cost of materials engraving charges conveyance and fixing chargers etc.. complete including all cost for fixing the granite slab in nconcrete or metal board and cost for concreting the base of board.

Bidder Name

ANILKUMAR N