PALARIVATTOM FLYOVER BEAUTIFICATION-PHASE 1

CIVIL WORKS

15.2.2 Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:4:8 or leaner mix ( including equivalent design mix)

OD364655/2025-2026 Dismantling and stacking with in 50 metres lead, existing barricades of 1.5 mtr length with 1.5 inch round SS steel pipe/1.5 inch square SS steel pipe horizontaly with 10 nos of vertical rods including all earth work and dismantling of concrete etc. in base of RCC.(OD BASED ON ITEM NO.15.34.2)

15.23.1 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

OD364975/2025-2026 55.16. Providing and fixing guard post Providing and fixing guard post of size 200mmx200mm, 1400mm long, 800mm above ground level and 600mm below GL. casted in M20 Grade concrete reinforced with 4 nos of 8mm dia longitudinal bars and 6mm dia stirrups @ 100mm c/c, firmly fixed in position by means of foundation of size 0.5mx0.5mx0.7m in M15 grade concrete below ground level including painting 2 coats on exposed surface with synthetic enamel paint as per required colour and shade with lighting provision-LED surface top light

OD365018/2025-2026 Supplying and fixing Movable Barricades made of steel components, 1.5 m high from road level, fitted with 2 inch MS square pipes(5nos) outer frame of size 1.2mx1.5m and 1.5 inch MS square pipes vertically connected to the frame with 20cm width 2mm MS sheet on top of the element and standard quality moving wheels at bottom 3pairs, painting as per the direction of engineer in charge. (OD Based on item 8.44.A MORTH)

OD435405/2025-2026 Construction of a permanent type barricade made of steel components, 1.2 m high from road level, fitted with 5 horizontal steel rod of 16mm Dia, connected to 3nos of vertical MS square pipe of size 40 × 40 × 4 mm with base plate and top horizontal rail of Round MS pipe 1.5 inch dia. painting as per the direction of engineer in charge. based on OD(8.44.A MORTH)

2.1.1 Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed:All Kinds of soil

16.78.2 Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

OD432555/2025-2026 Providing and laying 60 mm thick factory made Cement interlocking paver block of M30 grade-made-by block making machine with strong vibratory compaction ,of approved size, design, shape laid in required colour and pattern over and including 50mm thick compacted bed of stone aggregate etc all complete as per the-direction of engineer in charge.OD80/2122

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.1.3 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

15.60 Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

OD365134/2025-2026 Floor painting with floor emulsion paint of approved brand and manufacture of required colour to give an even shade including primer: Two or more coats on New work

2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil

4.1.5 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

10.1 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

OD364537/2025-2026 Providing and fixing 2 mm thick Perforated sheet(20 mm hole), with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm M.S. gusset plates at the junction and corners, 25 mm dia pulley, 40x40x6 mm angle and T-iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer as per the direction of engineer in charge.

OD364536/2025-2026 Finishing flyover component structure surfaces with SOLID COLOUR painting with one coat of suitable primer and two coat of superior quality exterior acrylic emulsion JSW Profect Regal Interior/Exterior Paint or equivalent as per required colour, shade and design based on architectural drawings including labour and materials, machinery, pressure wash cleaning, surface preparation, scaffolding, generator rent ,fuel , crane/boom lift & water charges etc. all as per the direction of engineer in charge.

OD364535/2025-2026 Finishing flyover component structure surfaces with ARTISTIC painting with one coat of suitable primer and two coat of superior quality exterior acrylic emulsion JSW Profect Regal Interior/Exterior Paint or equivalent as per required colour, shade and design based on architectural drawings including labour and materials, machinery, pressure wash cleaning, surface preparation, scaffolding, generator rent ,fuel , crane/boom lift & water charges etc. all as per the direction of engineer in charge.

OD366985/2025-2026 Finishing with Artistic painting on perforated sheets with Direct-to-Metal (DTM) Polyurethane (PU) Enamel Paint with high gloss finish applied as per manufacturer's specifications including appropriate priming coat, preparation of surface,including scaffolding and other vertical Access equipments up to 3.5 mtr height etc. complete.On steel work as per the instruction of Engineer in charge.

4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

13.111.2 Finishing walls with Acrylic Smooth exterior paint of required shade :Old work (One or more coat applied @ 0.90 ltr/10 sqm).

ELECTRICAL WORKS

OD435733/2025-2026 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 120 mm dia (OD-120 mm & ID-103 mm nominal) (od based on ITEM NO 14.15.3 of Electrical work)

OD435734/2025-2026 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 63 mm· dia (OD-63 mm & ID-51 mm nominal) (od Based on ITEM NO.14.15.1 Electrical work)

Please Enable Macros to View BoQ information