SPECIAL REPAIRS TO BLDG NO NP 80 TWIN NISSAN HUT AT MIL STN DHRANGADHRA

Amount

Taking down old cement plaster any description on brick or stone wall/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc complete as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in CM including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for walling of random rubble, uncoursed well bounded, bedded and solidly hearted, built in Cement Mortar 1:6 complete all as specified and directed.

M & L for walling (Except stone) of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:6 complete all as specified and directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc 20mm for sand stone and dressing to face stones and dressing of face beds and joints as specified ,of random rubble walling ,uncoursed or brought upto courses completed as specified and directed .

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Providing cement concrete 40 mm thick type B-1 (1:2:4) using 20 mm graded agg as in flooring with finishing cement concrete surface even and smooth using extra cement complete all as specified and directed.

Supply only polyester triangular fibres as secondary reinforcement in all types of concrete and mortars complete all as specified and directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces on wall in CM 1:4 and finishing even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces on wall in CM 1:6 and finishing even and smooth without using extra cement complete all as specified and directed.

Preparing of plastered or unplastered old decorated surfaces of walls by complete removal of existing treatment, moulds, moss and efflorescent salt and treating oil and greasy spots and applying three coat of white wash on walls including cornices etc complete all as specified and directed

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying one coats of cement base paint complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 20mm graded stone for embedding of hold fast ,filling etc complete all as specified and directed.

Demolition of reinforced cement concrete in any position not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 as in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like including demolition of existing RCC work in any position complete all as specified and as directed.

Use and waste of form work to soffit of suspanded slab such as roof slab ,floor slab landing and similar work n exc 200mm thick (horizontally or sloping complete all as specified and as directed.

M&L for TMT bar 10 mm dia and over including cutting bending and binding with MS wire anealed dia not less than 0.9 mm conplete all as specified and as directed.

Dismantling plain or corrugated steel sheeting any gauge ,thickness ,including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L for Pre- painted galvalume aluminium zinc coating GI based corrugated semi circular shape/D shape sheet 0.50 mm thick of an colour (as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws in single length complete all as specified and directed.

M&L for Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour (as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws in single length complete all as specified and directed.

M&L for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour (as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, valley gutter ,drip and straight flashing fixed with self tapping screws all as specified and directed.

M&L for 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof ,wall etc complete all as specified and directed.

S&F, rolled mild steel section as in main and cross beams hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates conforming to Fe-410, Gde E-250A all as specified and directed.

All as per item No 24 but fixing only complete all as specified and directed.

S&F for mild steel for joist ,channel, angle ,ortee sections fixed independently ,without connecting plates, etc (cut to ordinary lengths i.e. without 20mm of the length indicated) and confir to Fe-410-w (GdeE-250) quality A including one shop coat of zinc chrome primer complete all as specified and directed.

M&L, preparing of new steel surface exceeding 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L, preparation old previously treated steel Surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint on the steel surfaces, complete all as specified and directed.

Dismantling structure steel work including doors, gates etc. complete all as specified and directed.

Taking down and refixing of hanger door shutters in same position after making proper alignment, easening, greasing, replacing defective bearings, rollers, CGI/PGI sheets in shutters and proper functioning including all necessary tools and plants required all as specified and direced. Size of shutters upto 7.45 x 8.10m and weight upto 2.00 tonnes complete all as specified and directed.

S&F, steel bearings with appropriate bushings for bottom rollers of hanger shutters complete all as specified and directed.

S&F, bottom rollers of 185 mm dia and 60 mm in length for hanger shutters complete all as specified and directed.

S&F, steel top rollers of dia 85 mm and length 55 mm for hanger shutter complete all as specified and directed.

S&F, 0.63mm thick plain, galvanised, mild steel sheeting, class-3 in ridges, hips, valey gutters, cladings etc fixed with coach screws and washers etc. complete all as specified and directed.

S&F, framed work as in doors of Hangers or gates of angle or other sections with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering, doors etc confirming to grade Fe-410-w(Gde -E-250)Quality A all as specified and directed.

S&F, MS angle iron framed work as in doors or gate of angle or other section conforming to Fe 290 (Gde E-165) with gusset plates rails braces etc complete including hangin galso fastenin gand fxing complete as specified and directed .

M&L for 50 mm thick PCC 1:3:6 type C-2 (using 40 mm graded Stone aggregate) as in plinth protection finisheed with out using extra cement complete all as specified and directed.

M&L for plastic dividing strips 3.00mm thick inserted in position conform to design and 28 mm width of strip complete all as specified and directed.

Demolition of precast concrete articles and pre-cast cement concrete block walling, ashlar fencings, dressed stone work including all quoins, arches, pillars etc. built in cement mortar complete all as specified and directed.

M&L, precast cement concrete Block Masonary with solid blocks type C1, 1:3:6 (20mm graded stone aggregate) exc 10 cm in width and setting in mortar 1:6 complete all as specified and directed .

M&L, precast cement concrete Block Masonary with solid blocks (except block) type C1, 1:3:6 (20mm graded stone aggregate) exc 10 cm in width and setting in mortar 1:6 complete all as specified and directed .

M&L, providing cement concrete1:2:4 type B1 as in , coping ,benching, bressumers, steps, incl necessary form work and demolition of existing cement work complete all as specified and as directed.

Demolition of plain cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for Hardcore Broken stone or boulders of gauge n exc 63mm, deposited spread and levelled in layers n exc 15 cm thick ,watered and rammed to a true surface complete all as specified and directed .

M&L for PCC in 1:5:10 type E-2 (using 40 mm graded stone aggregate) as in subbase of floors etc, complete all as specified and directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour,design & pattern as in footpath parks, lawns ,drive ways or light traffic parking etc ,of required strength , thickness & size /shape ,made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of coarse sand , compacting and proper embedding /laying of inter locking paver block into the sand bedding layer through vibratory compaction by using plate vibrator ,filling the joints with fine sand and cutting of paver block as per required size and pattern ,finishing and sweeping extra sand complete all as specified and as directed.

S&F M.S Framed work such as grills gratings etc with ends of bars sholdered and/or riveted into spikes ,framed guard bars /railings all as directed .

partechengineers (BID ID -3452349)

ALBA AC AND REF SERVICES (BID ID -3451617)