Design, Manufacture, Supply and Installation of Laboratory Work Stations/ Furniture, Fume Extraction Systems and Allied Works (Re-tender - II)

GROUND FLOOR AREA

GLASS WARE STORE

Cabinet body shall be made out of min. 18mm thick hot pressed BWR plywood . All exposed edges are to be lipped with edge banding to protect from moisture and insects. Front edges are to be lipped with edging not less than 3 mm to protect from impacts. The Cabinet body should be made of permanent casework without any screws and knockdown / mini-fix fittings with necessary adhesives. The PVC Edging shall be from REHAU/SCANWOLF/DOLKEN. The Melamine Laminate to confirms to BS, NEMA & BIS Standards. (Melamine laminate makes shall be from Merino/ Formica/ Green lam/ Bloom/ Gratis/ Wilsonart) Doors Shall be with 6 mm thick plain glass built in to single panel without joints. The material of the door panel shall be made of 18mm thick melamine laminated plywood. All exposed edges are lipped with PVC lipping not less than 3 mm to protect from impacts, moisture and insects.

CHEMICAL STORE - with exhaust

Storage area for Storing acids (10 ft x 4 ft ) with exhaust Room Partition & sand filled area shall be built for store strong acids. Exhaust as per the standards

Polypropylene chemical storage cabinet size:800x 400x1800mm(h) These units shall be completely made of Chemical Resistant PP (Polypropylene) sheets. The Door and cabinet body shall be made of 15mm thick Polypropylene Sheets and the back wall of 6mm. All joints are fusion welded. There shall be no exposed part of metal in the cabinet, even the hinges shall be made of polypropylene. A Polypropylene “D” shaped handle shall be fixed on the door. The fixed shelves edges shall be raised to avoid spillage.

CRITICAL CHEMICAL STORE

Polypropylene chemical storage cabinet size:800x 500x1800mm(h) These units shall be completely made of Chemical Resistant PP (Polypropylene) sheets. The Door and cabinet body shall be made of 15mm thick Polypropylene Sheets and the back wall of 6mm. All joints are fusion welded. There shall be no exposed part of metal in the cabinet, even the hinges shall be made of polypropylene. A Polypropylene “D” shaped handle shall be fixed on the door. The fixed shelves edges shall be raised to avoid spillage. The blower housingis of strong ‘high density UV treated Polypropylene’ for maximum corrosion resistance, the impeller is completely made of Polypropylene with noise level less than 62 dB.This shall be ducted outside to the dised location.

Flammable storage cabinet size:900x 500x1800mm(h) Fabricated with 1mm thick galvanized iron sheet. Cabinets shall be double pan construction, with insulating material fastened to the inside for sound deadening, and strength. Doors are pre – treated with seven tank chemical process and powder coated with highly chemical resistant epoxy colour having dry film thickness of minimum 70 -80 microns. Doors comes with three-point self-latching. Manual-close doors opens to a 100 degrees and self-latches when pushed closed. For added security, handle comes with a cylinder lock and key. Cabinet provided with levelling jacks. Door styles meet OSHA and NFPA 30 standards.

STORE KEEPER ROOM

L SHAPE BENCH for Store Keeper 1200+1200 x600x 750mm mm 18mm thick melamine laminated plywood worktop 600mm wide 2.4 rm length, u/b cabinet with one adjustable shelf plus door 500 mm wide & lock, 1 no RJ45 socket, 1 no CPU hanger, 2 nos 6/16 Amps sockets, Keyboard tray, wire manager with knee covering / support panels to complete the bench.

LIBRARY

Reading table 2400 x 1200 x 750 mm 18mm thick melamine laminated plywood worktop 1200mm wide 2.4 rm length with support panels.

Lockable Glass inbuilt Tall storage cabinet size:900x400x 1800mm(h) Cabinet body shall be made out of min. 18mm thick hot pressed BWR plywood . All exposed edges are to be lipped with edge banding to protect from moisture and insects. Front edges are to be lipped with edging not less than 3 mm to protect from impacts. The Cabinet body should be made of permanent casework without any screws and knockdown / mini-fix fittings with necessary adhesives. The PVC Edging shall be from REHAU/SCANWOLF/DOLKEN. The Melamine Laminate to confirms to BS, NEMA & BIS Standards. (Melamine laminate makes shall be from Merino/ Formica/ Green lam/ Bloom/ Gratis/ Wilsonart) Doors Shall be with 6 mm thick plain glass built in to single panel without joints. The material of the door panel shall be made of 18mm thick melamine laminated plywood. All exposed edges are lipped with PVC lipping not less than 3 mm to protect from impacts, moisture and insects.

DINNING AREA

Dinning table 2400 x 1200 x 750 mm 18mm thick melamine laminated plywood worktop 1200mm wide 2.4 rm length with support panels.

OFFICE OF Chief Government Analyst

L SHAPE BENCH 1800+600mm x750/600 x 750MM 18mm thick melamine laminated plywood worktop 750mm/600mm wide 2.4 rm length, with 1 no u/b cabinet with drawer plus door 500 mm wide & lock,RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, Keyboard tray,1 no wire manager with knee covering / support panels to complete the bench.

Lockable tall storage cabinet with panel doors size:900x450x1800mm(h) Cabinet body shall be made out of min. 18mm thick hot pressed BWR plywood . All exposed edges are to be lipped with edge banding to protect from moisture and insects. Front edeges are to be lipped with edging not less than 3 mm to protect from impacts. The Cabinet body should be made of permanent casework without any screws and knockdown / mini-fix fittings with necessary adhesives. The PVC Edging shall be from REHAU/SCANWOLF/DOLKEN. The Melamine Laminate to confirms to BS, NEMA & BIS Standards. (Melamine laminate makes shall be from Merino/ Formica/ Green lam/ Bloom/ Gratis/ Wilsonart) Doors Shall be made out of same material as cabinet body. All exposed edges are lipped with PVC lipping not less than 3 mm to protect from impacts, moisture and insects.

Table 900 x 900 x 750 mm 18mm thick melamine laminated plywood worktop 1200mm wide 2.4 rm length with support panels.

STORE

Lockable tall storage cabinet with panel doors size:900x400x1800mm(h) Cabinet body shall be made out of min. 18mm thick hot pressed BWR plywood . All exposed edges are to be lipped with edge banding to protect from moisture and insects. Front edeges are to be lipped with edging not less than 3 mm to protect from impacts. The Cabinet body should be made of permanent casework without any screws and knockdown / mini-fix fittings with necessary adhesives. The PVC Edging shall be from REHAU/SCANWOLF/DOLKEN. The Melamine Laminate to confirms to BS, NEMA & BIS Standards. (Melamine laminate makes shall be from Merino/ Formica/ Green lam/ Bloom/ Gratis/ Wilsonart) Doors Shall be made out of same material as cabinet body. All exposed edges are lipped with PVC lipping not less than 3 mm to protect from impacts, moisture and insects.

Lockable tall storage cabinet with panel doors size:900x450x1800mm(h) Cabinet body shall be made out of min. 18mm thick hot pressed BWR plywood . All exposed edges are to be lipped with edge banding to protect from moisture and insects. Front edeges are to be lipped with edging not less than 3 mm to protect from impacts. The Cabinet body should be made of permanent casework without any screws and knockdown / mini-fix fittings with necessary adhesives. The PVC Edging shall be from REHAU/SCANWOLF/DOLKEN. The Melamine Laminate to confirms to BS, NEMA & BIS Standards. (Melamine laminate makes shall be from Merino/ Formica/ Green lam/ Bloom/ Gratis/ Wilsonart) Doors Shall be made out of same material as cabinet body. All exposed edges are lipped with PVC lipping not less than 3 mm to protect from impacts, moisture and insects.

SAMPLE ROOM

PENINSULAR BENCH 2000 x 1500 x 900 mm 16mm thick trespa worktop 1500mm wide 2 rm length, with 2 nos u/b cabinet with one adjustable shelf & door 600 mm wide & lock,2 nos lockable u/b cabinet with drawer & door cabinet 600mm wide, with knee covering / support panels to complete the bench.

Lockable tall storage cabinet with panel doors size:900x450x1800mm(h) Cabinet body shall be made out of min. 18mm thick hot pressed BWR plywood . All exposed edges are to be lipped with edge banding to protect from moisture and insects. Front edeges are to be lipped with edging not less than 3 mm to protect from impacts. The Cabinet body should be made of permanent casework without any screws and knockdown / mini-fix fittings with necessary adhesives. The PVC Edging shall be from REHAU/SCANWOLF/DOLKEN. The Melamine Laminate to confirms to BS, NEMA & BIS Standards. (Melamine laminate makes shall be from Merino/ Formica/ Green lam/ Bloom/ Gratis/ Wilsonart) Doors Shall be made out of same material as cabinet body. All exposed edges are lipped with PVC lipping not less than 3 mm to protect from impacts, moisture and insects.

Lockable tall storage cabinet with panel doors size:900x400x1800mm(h) Cabinet body shall be made out of min. 18mm thick hot pressed BWR plywood . All exposed edges are to be lipped with edge banding to protect from moisture and insects. Front edeges are to be lipped with edging not less than 3 mm to protect from impacts. The Cabinet body should be made of permanent casework without any screws and knockdown / mini-fix fittings with necessary adhesives. The PVC Edging shall be from REHAU/SCANWOLF/DOLKEN. The Melamine Laminate to confirms to BS, NEMA & BIS Standards. (Melamine laminate makes shall be from Merino/ Formica/ Green lam/ Bloom/ Gratis/ Wilsonart) Doors Shall be made out of same material as cabinet body. All exposed edges are lipped with PVC lipping not less than 3 mm to protect from impacts, moisture and insects.

ATTENDER AREA

WALL BENCH 2400 x 600 x 750 mm 18mm thick melamine laminated plywood worktop 600mm wide 2.4 rm length , with knee covering / support panels to complete the bench.

ROOM - Government Analyst 1

Office Cubicle Partition + Office Table 1200+1200 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 600mm wide 2.4 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, Keyboard tray,1 no wire manager with knee covering / support panels to complete the bench .

Lockable tall storage cabinet with panel doors size:900x400x1500mm(h) Cabinet body shall be made out of min. 18mm thick hot pressed BWR plywood . All exposed edges are to be lipped with edge banding to protect from moisture and insects. Front edeges are to be lipped with edging not less than 3 mm to protect from impacts. The Cabinet body should be made of permanent casework without any screws and knockdown / mini-fix fittings with necessary adhesives. The PVC Edging shall be from REHAU/SCANWOLF/DOLKEN. The Melamine Laminate to confirms to BS, NEMA & BIS Standards. (Melamine laminate makes shall be from Merino/ Formica/ Green lam/ Bloom/ Gratis/ Wilsonart) Doors Shall be made out of same material as cabinet body. All exposed edges are lipped with PVC lipping not less than 3 mm to protect from impacts, moisture and insects.

ROOM- Government Analyst 2

Office Cubicle Partition + Office Table 1200+1200 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 600mm wide 2.4 rm length , 1 no u/b cabinet with drawer plus door size 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, Keyboard tray,1 no wire manager with knee covering / support panels to complete the bench.

Lockable tall storage cabinet with panel doors size:900x400x1500mm(h) Cabinet body shall be made out of min. 18mm thick hot pressed BWR plywood . All exposed edges are to be lipped with edge banding to protect from moisture and insects. Front edeges are to be lipped with edging not less than 3 mm to protect from impacts. The Cabinet body should be made of permanent casework without any screws and knockdown / mini-fix fittings with necessary adhesives. The PVC Edging shall be from REHAU/SCANWOLF/DOLKEN. The Melamine Laminate to confirms to BS, NEMA & BIS Standards. (Melamine laminate makes shall be from Merino/ Formica/ Green lam/ Bloom/ Gratis/ Wilsonart) Doors Shall be made out of same material as cabinet body. All exposed edges are lipped with PVC lipping not less than 3 mm to protect from impacts, moisture and insects.

ROOM- Government Analyst 3

Office Cubicle Partition + Office Table 1200+1200 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 600mm wide 2.4 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, Keyboard tray,1 no wire manager with knee covering / support panels to complete the bench.

Lockable tall storage cabinet with panel doors size:900x400x1500mm(h) Cabinet body shall be made out of min. 18mm thick hot pressed BWR plywood . All exposed edges are to be lipped with edge banding to protect from moisture and insects. Front edeges are to be lipped with edging not less than 3 mm to protect from impacts. The Cabinet body should be made of permanent casework without any screws and knockdown / mini-fix fittings with necessary adhesives. The PVC Edging shall be from REHAU/SCANWOLF/DOLKEN. The Melamine Laminate to confirms to BS, NEMA & BIS Standards. (Melamine laminate makes shall be from Merino/ Formica/ Green lam/ Bloom/ Gratis/ Wilsonart. Doors Shall be made out of same material as cabinet body. All exposed edges are lipped with PVC lipping not less than 3 mm to protect from impacts, moisture and insects.

STORE SUPERITENDANT

L SHAPE BENCH 1200+1200 x 600 x 750 mm 18mm thick melamine laminated plywood worktop 600mm wide 2.4 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, Keyboard tray,1 no wire manager with knee covering / support panels to complete the bench.

SAMPLE WARDEN

L SHAPE BENCH 1200+1200 x 600 x 750 mm 18mm thick melamine laminated plywood worktop 600mm wide 2.4 rm length , 1 no u/b cabinet with drawer plus door cabinet 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, Keyboard tray,1 no wire manager with knee covering / support panels to complete the bench.

ROOM - JS

L SHAPE BENCH 1200+1000 x800/ 600 x 750 mm 18mm thick melamine laminated plywood worktop 800/600mm wide 2.2 rm length , 1 no u/b cabinet with drawer plus door cabinet 450 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, Keyboard tray,1 no wire manager with knee covering / support panels to complete the bench.

ROOM - SS

L SHAPE BENCH 1200+1370 x 800/600 x 750 mm 18mm thick melamine laminated plywood worktop 800/600mm wide 2.2 rm length , 1 no u/b cabinet with drawer plus door cabinet 450 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, Keyboard tray,1 no wire manager with knee covering / support panels to complete the bench.

OFFICE ROOM

Office Cubicle Partition + L SHAPE office table 1200+700 x800/600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 800/600mm wide 1.9 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

Office Cubicle Partition + office table 1500 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 600mm wide 1.5 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

FIRST FLOOR AREA

PREPARATION AREA

L Shape Bench 3000+1200 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 4.2 rm length , 1 no lockable u/b cabinet with one adjustable shelf and door 500 mm wide ,1 no lockable u/b cabinet with one adjustable shelf and door 600mm wide ,1 no lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide lock,1 no u/b sink cabinet 600mm wide, 1 no polypropylene sink of size 450 x 350 x 200mm, 1 no cold water standout with double out let, with knee covering / support panels to complete the bench.

Fume cupboard 1525 x 900 x 2400 mm wide with Polypropylene u/b cabinet services are water,gas(lpg) and electrical ( All Fumehoods shall provide with suitable Three phase Polypropylene blower as specified) Fume hood shall be double wall metal construction. The interior of construction including the baffle shall be from chemical & heat resistant, fire retardant, smooth finish, easily cleanable panels made out of electron beam cured phenolic resin material 6 mm thick . chemical resistant splash & spillage proof dished 25 mm thick Solid Epoxy resin worktop. Clear open able height shall be 750 mm. Two no’s electrical sockets 6/16 A. LED tube lighting shall be provided in a separate protective sealed chamber . Fume hood under bench cabinet shall be completely made of Chemical Resistant PP (Polypropylene) sheets. The Door and cabinet body shall be made of 15mm thick Polypropylene Sheets and the back wall of 6mm. All joints are fusion welded. There shall be no exposed part of metal in the cabinet, even the hinges shall be made of polypropylene. A Polypropylene “D” shaped handle shall be fixed on the door. The fixed shelves edges shall be raised to avoid spillage. Individual blower & motor shall be of three phase with appropriate capacity to ensure sufficient capcity as per ASHARE 110-2016.Blower housing shall be of strong high density UV treated polypropylene for maximum corrosion resistance and the high performance impeller is completely made of 100% polypropylene with noise level less than 62 db. The performance shall be tested in house accordance with AMCA 210-85 and ISO 5801

INSTRUMENTAL AREA

L SHAPE BENCH 3000+3000 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 6 rm length , 2 nos lockable u/b cabinet with one adjustable shelf and door 600 mm wide, 2 nos lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide , with knee covering / support panels to complete the bench.

MICROBALANCE AREA

Balance bench ,Size.900x600x900mm (H) Fabricated with heavy duty metal tube section of size 100x50x 2mm. Heavy Granite platform of 30 mm thick will be placed on highly sensitive anti vibration pads independently attached to the frame work. The complete bench rests on special vibration dampening, leveling feet in order to install even at unleveled site conditions.

WORK TABLE 1500 x 600 x 900 mm 18 (±1)mm thick granite worktop 600 mm wide 1.5 rm length , With 30 x 30 x 2 mm thick powder coated steel frame.

CHEMICAL AREA AND INSTRUMENTAL AREA 01

C SHAPE BENCH 3000+3800+1500 x 1500/750 x 900 mm 16mm thick Trespa worktop 1500/750mm wide with backsplash 3+5.3 rm length , 3 nos lockable u/b cabinet with one adjustable shelf and door 600 mm wide ,3 nos lockable u/b cabinet one drawer , one adjustable shelf and door of size 600mm wide, 12 nos 6/16 A socket on pedestal box, 300mm wide two tier height adjustable reagent rack 3 rm, with knee covering / support panels to complete the bench.

L SHAPE BENCH 4000+4500 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 8.5 rm length , 2 nos lockable u/b cabinet with one adjustable shelf and door 600 mm wide, 2 nos lockable u/b with cabinet one drawer , one adjustable shelf and door 600mm, 1 no u/b sink cabinet of size 600mm wide,1 no Polypropylene sink 450 x 350 x200mm ,1 no bench mounted eyewash, 1 no cold water standout with double outlet, with knee covering / support panels to complete the bench.

Fume cupboard 1525mm wide with Polypropylene u/b cabinet services are water,gas(lpg) and electrical ( All Fumehoods shall provide with suitable Three phase Polypropylene blower as specified) Fume hood shall be double wall metal construction. The interior of construction including the baffle shall be from chemical & heat resistant, fire retardant, smooth finish, easily cleanable panels made out of electron beam cured phenolic resin material 6 mm thick . Chemical resistant splash & spillage proof dished 25 mm thick Solid Epoxy resin worktop. Clear open able height shall be 750 mm. Two no’s electrical sockets 6/16 A. LED tube lighting shall be provided in a separate protective sealed chamber . Fume hood under bench cabinet shall be completely made of Chemical Resistant PP (Polypropylene) sheets. The Door and cabinet body shall be made of 15mm thick Polypropylene Sheets and the back wall of 6mm. All joints are fusion welded. There shall be no exposed part of metal in the cabinet, even the hinges shall be made of polypropylene. A Polypropylene “D” shaped handle shall be fixed on the door. The fixed shelves edges shall be raised to avoid spillage. Blower & motor shall be of three phase with appropriate capacity to ensure suffucient capcity as per ASHARE 110-2016.Blower housing shall be of strong high density UV treated polypropylene for maximum corrosion resistance and the high performance impeller is completely made of 100% polypropylene with noise level less than 62 db. The performance shall be tested in house accordance with AMCA 210-85 and ISO 5801

UV AREA

WALL BENCH 1000+4000+2250+1500 x 750 x 900 MM 16mm thick Trespa worktop 750mm wide with backsplash 8.75 rm length , 1 no lockable u/b cabinet with one adjustable shelf and door 600 mm wide, 1no lockable u/b cabinet with one drawer , one adjustable shelf and door 450mm wide ,1no lockable u/b cabinet with one drawer , one adjustable shelf and door 500mm wide, 1no lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide , 1 no u/b sink cabinet of size 600mm wide,1 no Polypropylene sink 450 x 350 x200mm ,1 no Polypropylene drip rack with 27 pegs, 1 no cold water standout , with knee covering / support panels to complete the bench.

HPLC ROOM

C SHAPE BENCH 4800+5179+5309 x 750 x 750mm 16mm thick Trespa worktop 750mm wide with backsplash 15.3 rm length , 10 nos lockable u/b cabinet with one drawer, one adjustable shelf and door 600 mm wide , 8nos. Cpu hanger, 8 nos keyboard tray, 8 nos. R45 sockets,32 nos 6/16 A sockets, 24 6 A sockets , 8 nos cable manager,with knee covering / support panels to complete the bench.

ISLAND BENCH 2000 x 1000 x 750 mm 16mm thick Trespa worktop 1000mm wide 2 rm length , 2 nos lockable u/b cabinet with one drawer, one adjustable shelf and door 500 mm wide, 1no. Cpu hanger, 1no keyboard tray,1 no. R45 sockets, 10 nos 6/16 A sockets, 1no wire manager , with knee covering / support panels to complete the bench.

Ceiling mounted suction arm with sufficient capacity polypropylene blower/s as specified It is to be provided as suspended from wall/ ceiling on work positions, with adjustable arms and suction cup. The flexible arm system shall use friction joints and ball bearing for necessary grip and easy movement. The suction tubes will be made of smooth aluminum. All suction arm has connected to an exhaust system which having a sufficient capacity blower.Suction arm shall confirm to 85/374/EEC. Blower & motor shall be of three phase with appropriate capacity to ensure sufficient capcity as per ASHARE 110-2016.Blower housing shall be of strong high density UV treated polypropylene for maximum corrosion resistance and the high performance impeller is completely made of 100% polypropylene with noise level less than 62 db. The performance shall be tested in house accordance with AMCA 210-85 and ISO 5801

Open tall storage cabinet size:900x400x1800mm(h), with Heavy duty shelves Cabinet body shall be made out of min. 18mm thick hot pressed BWR plywood . All exposed edges are to be lipped with edge banding to protect from moisture and insects. Front edeges are to be lipped with edging not less than 3 mm to protect from impacts. The Cabinet body should be made of permanent casework without any screws and knockdown / mini-fix fittings with necessary adhesives. The PVC Edging shall be from REHAU/SCANWOLF/DOLKEN. The Melamine Laminate to confirms to BS, NEMA & BIS Standards. (Melamine laminate makes shall be from Merino/ Formica/ Green lam/ Bloom/ Gratis/ Wilsonart)

FTIR ROOM

WALL BENCH 1000 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide 1 rm length with back splash ,with powder coated frames , with knee space/ support panels & Cantelever Framework

WALL BENCH 3000 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide 3 rm length with back splash , lockable u/b cabinet with one adjustable shelf and door 600mm wide ,lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide, with knee space/ support panels to complete the bench.

GC ROOM

WALL BENCH 2000 x 1000 x 900 mm 16mm thick Trespa worktop 1000mm wide 2 rm length , 1 no lockable u/b cabinet with one adjustable shelf & door 600mm wide, 1 no lockable u/b cabinet of one drawer , one adjustable shelf & door 600mm wide,RJ 45 Socket, 4 nos. 6/16A sockets , with knee space/ support panels to complete the bench.

MOVABLE TABLE 1700 x 1000 x 900 mm 16mm thick Trespa worktop 1000mm wide 1.7 rm length ,with powder coated frame work

Floor mounted emergency shower with eye wash Emergency Shower and eyewash shall be manufactured according to CE – DIN 12 899 – UNI 9608 standards and they will be characterized by high water flow along with a very soft water spout (DIN EN 246 standard). Eye wash shall be equipped with eye protecting rubber cups and anti-dust covers. Emergency shower and Eye wash shall be from Water saver/ Broen/ TOF Italy. c/w with On/Off valve operated by hand or foot, filter debris to eye wash with base to fix the shower.

CHEMICAL AREA AND INSTRUMENTAL AREA 02

Fume cupboard 1525mm wide with Polypropylene u/b cabinet services are water,gas(lpg) and electrical ( All Fumehoods shall provide with suitable Three phase Polypropylene blower as specifed) Fume hood shall be double wall metal construction. The interior of construction including the baffle shall be from chemical & heat resistant, fire retardant, smooth finish, easily cleanable panels made out of electron beam cured phenolic resin material 6 mm thick . Chemical resistant splash & spillage proof dished 25 mm thick Solid Epoxy resin worktop. Clear open able height shall be 750 mm. Two no’s electrical sockets 6/16 A. LED tube lighting shall be provided in a separate protective sealed chamber . Fume hood under bench cabinet shall be completely made of Chemical Resistant PP (Polypropylene) sheets. The Door and cabinet body shall be made of 15mm thick Polypropylene Sheets and the back wall of 6mm. All joints are fusion welded. There shall be no exposed part of metal in the cabinet, even the hinges shall be made of polypropylene. A Polypropylene “D” shaped handle shall be fixed on the door. The fixed shelves edges shall be raised to avoid spillage. Blower & motor shall be of three phase with appropriate capacity to ensure suffucient capcity as per ASHARE 110-2016.Blower housing shall be of strong high density UV treated polypropylene for maximum corrosion resistance and the high performance impeller is completely made of 100% polypropylene with noise level less than 62 db. The performance shall be tested in house accordance with AMCA 210-85 and ISO 5801

L SHAPE BENCH 3000+4000 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 7 rm length , 2 nos lockable u/b cabinet with one adjustable shelf & door 600mm wide ,2 nos lockable u/b cabinet with one drawer, one adjustable shelf and door 600mm wide,1 no u/b sink cabinet 600mm wide,1 no bench mounted eyewash, 1 no polypropylene sink 450x 350 x 200 mm,1 no. cold water standout with double outlet,8 nos. 6/16A sockets , with knee space/ support panels.

PENINSULAR BENCH 3000 x 1500 x 900 mm 16mm thick Trespa worktop 1500mm wide 3 rm length , 2 nos lockable u/b cabinet with one adjustable shelf and door 600mm wide ,2 nos lockable u/b cabinet with one drawer and one adjustable shelf & door 600mm wide, 2-Tier height adjustable reagent rack 300mm wide 3 rm length ,8 nos. 6/16A sockets , with knee space/ support panels to complete bench.

WALL BENCH 3800 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 3.8 rm length ,1 no lockable u/b cabinet with one adjustable shelf & door 600mm wide ,1no lockable u/b cabinet with one drawer, one adjustable shelf with door 600mm wide, 2 nos. 6/16A sockets , with knee space/ support panels to complete bench.

BALANCE ROOM

WORK TABLE 1800 x 600 x 900 mm 18 (±1)mm thick granite worktop 600 mm wide 1.8 rm length , With 30 x 30 x 2 mm thick powder coated steel frame.

Balance bench ,Size.900x600x900mm Fabricated with heavy duty metal tube section of size 100x50x 2mm. Heavy Granite platform of 30 mm thick will be placed on highly sensitive anti vibration pads independently attached to the frame work. The complete bench rests on special vibration dampening, leveling feet in order to install even at unleveled site conditions.

HOT AREA

WALL BENCH 2000 x 750 x 900 mm 20mm thick Granite worktop 750mm wide with backsplash 2 rm length ,2 nos lockable u/b cabinet with one adjustable shelf and door 600mm wide ,1no lockable u/b cabinet with one drawer, one adjustable shelf & door 600mm wide , with knee space/ support panels to complete the bench.

Workbench with Ceiling mounted hood, 1000mm wide with suitable blower Canopy hoods shall be suspended from the ceiling over the worktops at required levels; by means of threaded bar.The unit shall be made of stainless steel. The hood for connection to the exhaust system. Heavy duty Workbench shall be provided for the hood with granite worktop, complete with panels and framework. Canopy hood shall be connected to an exhaust system as specified which has a sufficient capacity blower.

CHEMICAL AREA AND INSTRUMENTAL AREA 03

SINK UNIT 1200 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 1.2 rm length , 1 no lockable u/b cabinet with one adjustable shelf & door 500mm wide,1 no u/b sink cabinet of size 600mm wide,1 no bench mounted eyewash, 1 no polypropylene sink 450x 350 x 200 mm,1 no. cold water standout with double outlet, with knee space/ support panels.

WALL + PENNINSULAR BENCH 3000+3750+5000+3000 x 1500/750 x 900 mm 16mm thick Trespa worktop 1500mm/750mm wide with back splash 3/11.75 rm length , 5 nos lockable u/b cabinet with one adjustable shelf & door 600mm wide ,5 nos lockable u/b cabinet with one drawer, one adjustable shelf & door 600mm wide, 2 Tier height adjustable reagent rack 300mm wide 3 rm length ,18 nos. 6/16A sockets , with knee space/ support panels.

Fume cupboard 1525mm wide with Polypropylene u/b cabinet services are water,gas(lpg) and electrical ( All Fumehoods shall provide with suitable Three phase Polypropylene blower), as specified. Fume hood shall be double wall metal construction. The interior of construction including the baffle shall be from chemical & heat resistant, fire retardant, smooth finish, easily cleanable panels made out of electron beam cured phenolic resin material 6 mm thick . Chemical resistant splash & spillage proof dished 25 mm thick Solid Epoxy resin worktop. Clear open able height shall be 750 mm. Two no’s electrical sockets 6/16 A. LED tube lighting shall be provided in a separate protective sealed chamber . Fume hood under bench cabinet shall be completely made of Chemical Resistant PP (Polypropylene) sheets. The Door and cabinet body shall be made of 15mm thick Polypropylene Sheets and the back wall of 6mm. All joints are fusion welded. There shall be no exposed part of metal in the cabinet, even the hinges shall be made of polypropylene. A Polypropylene “D” shaped handle shall be fixed on the door. The fixed shelves edges shall be raised to avoid spillage. Blower & motor shall be of three phase with appropriate capacity to ensure suffucient capcity as per ASHARE 110-2016.Blower housing shall be of strong high density UV treated polypropylene for maximum corrosion resistance and the high performance impeller is completely made of 100% polypropylene with noise level less than 62 db. The performance shall be tested in house accordance with AMCA 210-85 and ISO 5801

SITTING AREA - 1

Office Cubicle Partition + L SHAPE office table 1350+1000 X600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 800/600mm wide 1.9 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

Office Cubicle Partition + office table 1500 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 600mm wide 1.5 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

WALL BENCH 2400 x 600 x 750 mm 18mm thick melamine laminated plywood worktop 600mm wide 2.4 rm length , with knee covering / support panels to complete the bench.

COMMON SITTING AREA WITH PARTITION

L- SHAPE BENCH 2750+2950 x 600 x 750 mm 18mm thick melamine laminated plywood worktop 600mm wide 5.7 rm length

SITTING AREA 02

Office Cubicle Partition + L SHAPE office table 1350+1000 X600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 800/600mm wide 1.9 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

Office Cubicle Partition + office table 1200 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 600mm wide 1.5 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

SITTING AREA-03

Office Cubicle Partition + L SHAPE office table 1350+1000 X600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 800/600mm wide 1.9 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

Office Cubicle Partition + office table 1200 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 600mm wide 1.5 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

SITTING AREA 04

Office Cubicle Partition + L SHAPE office table 1350+1000 X600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 800/600mm wide 1.9 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

Office Cubicle Partition + L Shape office table 1200 +900 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 600mm wide 2.1 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

Gas distribution for First Floor (LPG - 1 Line)

SECOND FLOOR AREA

CHEMICAL AND INSTRUMENT AREA 01

C SHAPE BENCH 3000+4000+3000 x 1500/ 750 x 900 mm 16mm thick Trespa worktop 1500/750mm wide with backsplash 3+7 rm length , 4 nos. lockable u/b cabinet with one adjustable shelf and door 600 mm wide ,3 nos. lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide lock,14 nos. 6/16 A electrical sockets, 300mm wide 2 tier height adjustable reagent rack 3rm ,with knee covering / support panels to complete the bench.

L SHAPE BENCH 3000+4000 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 7 rm length , 2 nos lockable u/b cabinet with one adjustable shelf and door 600 mm wide,2 nos lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide ,1 no u/b sink cabinet 600mm wide, 1 no Polypropylene sink 450 x 350 x200mm ,1 no bench mounted eyewash, 1 no cold water standout with double outlet, with knee covering / support panels to complete the bench.

Fume cupboard 1525 x 900 x 2400 mm wide with Polypropylene u/b cabinet services are water,gas(lpg) and electrical ( All Fumehoods shall provide with suitable Three phase Polypropylene blower), as specified Fume hood shall be double wall metal construction. The interior of construction including the baffle shall be from chemical & heat resistant, fire retardant, smooth finish, easily cleanable panels made out of electron beam cured phenolic resin material 6 mm thick . chemical resistant splash & spillage proof dished 25 mm thick Solid Epoxy resin worktop. Clear open able height shall be 750 mm. Two no’s electrical sockets 6/16 A. LED tube lighting shall be provided in a separate protective sealed chamber . Fume hood under bench cabinet shall be completely made of Chemical Resistant PP (Polypropylene) sheets. The Door and cabinet body shall be made of 15mm thick Polypropylene Sheets and the back wall of 6mm. All joints are fusion welded. There shall be no exposed part of metal in the cabinet, even the hinges shall be made of polypropylene. A Polypropylene “D” shaped handle shall be fixed on the door. The fixed shelves edges shall be raised to avoid spillage. Individual blower & motor shall be of three phase with appropriate capacity to ensure sufficient capcity as per ASHARE 110-2016.Blower housing shall be of strong high density UV treated polypropylene for maximum corrosion resistance and the high performance impeller is completely made of 100% polypropylene with noise level less than 62 db. The performance shall be tested in house accordance with AMCA 210-85 and ISO 5801

CHEMICAL AND INSTRUMENT AREA 02

C SHAPE BENCH 3000+4000+3000 x 1500/ 750 x 900 mm 16mm thick Trespa worktop 1500/750mm wide with backsplash 3+7 rm length , 4 nos. lockable u/b cabinet with one adjustable shelf and door 600 mm wide ,3 nos. lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide lock,14 nos. 6/16 A electrical sockets, 300mm wide 2 tier height adjustable reagent rack 3rm ,with knee covering / support panels to complete the bench.

L SHAPE BENCH 3000+4000 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 7 rm length , 2 nos lockable u/b cabinet with one adjustable shelf and door 600 mm wide,2 nos lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide ,1 no u/b sink cabinet 600mm wide, 1 no Polypropylene sink 450 x 350 x200mm ,1 no bench mounted eyewash, 1 no cold water standout with double outlet, with knee covering / support panels to complete the bench.

Fume cupboard 1525 x 900 x 2400 mm wide with Polypropylene u/b cabinet services are water,gas(lpg) and electrical ( All Fumehoods shall provide with suitable Three phase Polypropylene blower), as specified Fume hood shall be double wall metal construction. The interior of construction including the baffle shall be from chemical & heat resistant, fire retardant, smooth finish, easily cleanable panels made out of electron beam cured phenolic resin material 6 mm thick . chemical resistant splash & spillage proof dished 25 mm thick Solid Epoxy resin worktop. Clear open able height shall be 750 mm. Two no’s electrical sockets 6/16 A. LED tube lighting shall be provided in a separate protective sealed chamber . Fume hood under bench cabinet shall be completely made of Chemical Resistant PP (Polypropylene) sheets. The Door and cabinet body shall be made of 15mm thick Polypropylene Sheets and the back wall of 6mm. All joints are fusion welded. There shall be no exposed part of metal in the cabinet, even the hinges shall be made of polypropylene. A Polypropylene “D” shaped handle shall be fixed on the door. The fixed shelves edges shall be raised to avoid spillage. Individual blower & motor shall be of three phase with appropriate capacity to ensure sufficient capcity as per ASHARE 110-2016.Blower housing shall be of strong high density UV treated polypropylene for maximum corrosion resistance and the high performance impeller is completely made of 100% polypropylene with noise level less than 62 db. The performance shall be tested in house accordance with AMCA 210-85 and ISO 5801

AAS ROOM

Island bench ,Size.2000x900x900mm (H) 16mm thick Trespa worktop 900mm wide with backsplash 2 rm length , 1 no lockable u/b cabinet with one adjustable shelf and door 600 mm wide, 1no. lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide ,2 no RJ45 socket, 8 nos., 8 nos. 6/16A electrical sockets, with knee covering / support panels to complete the bench.

Balance Room 1

WORK TABLE 1000 x 600 x 900 mm 18 (±1)mm thick granite worktop 600 mm wide 1. rm length , With 30 x 30 x 2 mm thick powder coated steel frame.

Balance bench ,Size.900x600x900mm Fabricated with heavy duty metal tube section of size 100x50x 2mm. Heavy Granite platform of 30 mm thick will be placed on highly sensitive anti vibration pads independently attached to the frame work. The complete bench rests on special vibration dampening, leveling feet in order to install even at unleveled site conditions.

CHEMICAL AREA AND INSTRUMENTAL AREA 03

C SHAPE BENCH 3000+4000+3000 x 1500/ 750 x 900 mm 16mm thick Trespa worktop 1500/750mm wide with backsplash 3+7 rm length , 4 nos. lockable u/b cabinet with one adjustable shelf and door 600 mm wide ,3 nos. lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide lock,14 nos. 6/16 A electrical sockets, 300mm wide 2 tier height adjustable reagent rack 3rm ,with knee covering / support panels to complete the bench.

L SHAPE BENCH 3000+4000 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 7 rm length , 2 nos lockable u/b cabinet with one adjustable shelf and door 600 mm wide,2 nos lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide ,1 no u/b sink cabinet 600mm wide, 1 no Polypropylene sink 450 x 350 x200mm ,1 no bench mounted eyewash, 1 no cold water standout with double outlet, with knee covering / support panels to complete the bench.

Fume cupboard 1525 x 900 x 2400 mm wide with Polypropylene u/b cabinet services are water,gas(lpg) and electrical ( All Fumehoods shall provide with suitable Three phase Polypropylene blower), as specified Fume hood shall be double wall metal construction. The interior of construction including the baffle shall be from chemical & heat resistant, fire retardant, smooth finish, easily cleanable panels made out of electron beam cured phenolic resin material 6 mm thick . chemical resistant splash & spillage proof dished 25 mm thick Solid Epoxy resin worktop. Clear open able height shall be 750 mm. Two no’s electrical sockets 6/16 A. LED tube lighting shall be provided in a separate protective sealed chamber . Fume hood under bench cabinet shall be completely made of Chemical Resistant PP (Polypropylene) sheets. The Door and cabinet body shall be made of 15mm thick Polypropylene Sheets and the back wall of 6mm. All joints are fusion welded. There shall be no exposed part of metal in the cabinet, even the hinges shall be made of polypropylene. A Polypropylene “D” shaped handle shall be fixed on the door. The fixed shelves edges shall be raised to avoid spillage. Individual blower & motor shall be of three phase with appropriate capacity to ensure sufficient capcity as per ASHARE 110-2016.Blower housing shall be of strong high density UV treated polypropylene for maximum corrosion resistance and the high performance impeller is completely made of 100% polypropylene with noise level less than 62 db. The performance shall be tested in house accordance with AMCA 210-85 and ISO 5801

Floor mounted emergency shower with eye wash Emergency Shower and eyewash shall be manufactured according to CE – DIN 12 899 – UNI 9608 standards and they will be characterized by high water flow along with a very soft water spout (DIN EN 246 standard). Eye wash shall be equipped with eye protecting rubber cups and anti-dust covers. Emergency shower and Eye wash shall be from Water saver/ Broen/ TOF Italy. c/w with On/Off valve operated by hand or foot, filter debris to eye wash with base to fix the shower.

CHEMICAL AREA AND INSTRUMENTAL AREA 04

C SHAPE BENCH 3000+4000+2000 x 1500/ 750 x 900 mm 16mm thick Trespa worktop 1500/750mm wide with backsplash 3+6 rm length , 4 nos. lockable u/b cabinet with one adjustable shelf and door 600 mm wide ,3 nos. lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide lock,12 nos. 6/16 A electrical sockets, 300mm wide 2 tier height adjustable reagent rack 3rm ,with knee covering / support panels to complete the bench.

L SHAPE BENCH 3000+4000 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 7 rm length , 2 nos lockable u/b cabinet with one adjustable shelf and door 600 mm wide,2 nos lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide ,1 no u/b sink cabinet 600mm wide, 1 no Polypropylene sink 450 x 350 x200mm ,1 no bench mounted eyewash, 1 no cold water standout with double outlet, with knee covering / support panels to complete the bench.

Fume cupboard 1525 x 900 x 2400 mm wide with Polypropylene u/b cabinet services are water,gas(lpg) and electrical ( All Fumehoods shall provide with suitable Three phase Polypropylene blower), as specified Fume hood shall be double wall metal construction. The interior of construction including the baffle shall be from chemical & heat resistant, fire retardant, smooth finish, easily cleanable panels made out of electron beam cured phenolic resin material 6 mm thick . chemical resistant splash & spillage proof dished 25 mm thick Solid Epoxy resin worktop. Clear open able height shall be 750 mm. Two no’s electrical sockets 6/16 A. LED tube lighting shall be provided in a separate protective sealed chamber . Fume hood under bench cabinet shall be completely made of Chemical Resistant PP (Polypropylene) sheets. The Door and cabinet body shall be made of 15mm thick Polypropylene Sheets and the back wall of 6mm. All joints are fusion welded. There shall be no exposed part of metal in the cabinet, even the hinges shall be made of polypropylene. A Polypropylene “D” shaped handle shall be fixed on the door. The fixed shelves edges shall be raised to avoid spillage. Individual blower & motor shall be of three phase with appropriate capacity to ensure sufficient capcity as per ASHARE 110-2016.Blower housing shall be of strong high density UV treated polypropylene for maximum corrosion resistance and the high performance impeller is completely made of 100% polypropylene with noise level less than 62 db. The performance shall be tested in house accordance with AMCA 210-85 and ISO 5801

Balance Room 2

WORK TABLE 1000 x 600 x 900 mm 18 (±1)mm thick granite worktop 600 mm wide 1. rm length , With 30 x 30 x 2 mm thick powder coated steel frame.

Balance bench ,Size.900x600x900mm Fabricated with heavy duty metal tube section of size 100x50x 2mm. Heavy Granite platform of 30 mm thick will be placed on highly sensitive anti vibration pads independently attached to the frame work. The complete bench rests on special vibration dampening, leveling feet in order to install even at unleveled site conditions.

Water Distribution Unit

Wall Bench 1500 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 1.5 rm length ,1 no u/b sink cabinet 1000mm wide, 1 no Polypropylene sink 810 x 470 x325mm, 1 no cold water standout t, with knee covering / support panels to complete the bench.

CHEMICAL AREA AND INSTRUMENTAL AREA 05

WALL BENCH 3000 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 3 rm length , 1 no lockable u/b cabinet with one adjustable shelf and door 600 mm wide, 1no lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide ,4 nos. 6/16 A electrical sockets on pedestal, with knee covering / support panels to complete the bench.

C SHAPE BENCH 5000+4360+3000 x 1500/ 750 x 900 mm 16mm thick Trespa worktop 1500/750mm wide with backsplash 3+9.36 rm length , 4 nos. lockable u/b cabinet with one adjustable shelf and door 600 mm wide ,4 nos. lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide lock,6 nos. 6/16 A electrical sockets,1 no u/b sink cabinet 600mm wide, 1 no Polypropylene sink 450 x 350 x200mm ,1 no bench mounted eyewash, 1 no cold water standout with double outlet, 300mm wide 2 tier height adjustable reagent rack 3rm ,with knee covering / support panels to complete the bench.

L SHAPE BENCH 3000+4000 x 750 x 900 mm 16mm thick Trespa worktop 750mm wide with backsplash 7 rm length , 2 nos lockable u/b cabinet with one adjustable shelf and door 600 mm wide,2 nos lockable u/b cabinet with one drawer , one adjustable shelf and door 600mm wide ,1 no u/b sink cabinet 600mm wide, 1 no Polypropylene sink 450 x 350 x200mm ,1 no bench mounted eyewash, 1 no cold water standout with double outlet, with knee covering / support panels to complete the bench.

Fume cupboard 1525 x 900 x 2400 mm wide with Polypropylene u/b cabinet services are water,gas(lpg) and electrical ( All Fumehoods shall provide with suitable Three phase Polypropylene blower), as specified Fume hood shall be double wall metal construction. The interior of construction including the baffle shall be from chemical & heat resistant, fire retardant, smooth finish, easily cleanable panels made out of electron beam cured phenolic resin material 6 mm thick . chemical resistant splash & spillage proof dished 25 mm thick Solid Epoxy resin worktop. Clear open able height shall be 750 mm. Two no’s electrical sockets 6/16 A. LED tube lighting shall be provided in a separate protective sealed chamber . Fume hood under bench cabinet shall be completely made of Chemical Resistant PP (Polypropylene) sheets. The Door and cabinet body shall be made of 15mm thick Polypropylene Sheets and the back wall of 6mm. All joints are fusion welded. There shall be no exposed part of metal in the cabinet, even the hinges shall be made of polypropylene. A Polypropylene “D” shaped handle shall be fixed on the door. The fixed shelves edges shall be raised to avoid spillage. Individual blower & motor shall be of three phase with appropriate capacity to ensure sufficient capcity as per ASHARE 110-2016.Blower housing shall be of strong high density UV treated polypropylene for maximum corrosion resistance and the high performance impeller is completely made of 100% polypropylene with noise level less than 62 db. The performance shall be tested in house accordance with AMCA 210-85 and ISO 5801

SITTING AREA 04

SITTING AREA WITH PARTITION L- SHAPE BENCH 2750+2950 x 600 x 750 mm 18mm thick melamine laminated plywood worktop 600mm wide 5.7 rm length

SITTING AREA 05

Office Cubicle Partition + L SHAPE office table 1350+1000 X600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 800/600mm wide 1.9 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

Office Cubicle Partition + L Shape office table 1200 +900 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 800/600mm wide 1.9 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

SITTING AREA-06

Office Cubicle Partition + L SHAPE office table 1350+1000 X600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 800/600mm wide 1.9 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

Office Cubicle Partition + office table 1200 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 600mm wide 1.5 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

SITTING AREA-07

Office Cubicle Partition + L SHAPE office table 1350+1000 X600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 800/600mm wide 1.9 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

Office Cubicle Partition + office table 1200 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 600mm wide 1.5 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

SITTING AREA - 08

Office Cubicle Partition + L SHAPE office table 1350+1000 X600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 800/600mm wide 1.9 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

Office Cubicle Partition + office table 1500 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 600mm wide 1.5 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

SITTING AREA - 09

Office Cubicle Partition + L SHAPE office table 1350+1000 X600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 800/600mm wide 1.9 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

Office Cubicle Partition + office table 1500 x 600 x 750 mm Office Table shall be made of 18mm thick melamine laminated plywood worktop 600mm wide 1.5 rm length , 1 no u/b cabinet with drawer plus door 500 mm wide & lock, RJ45 socket,1 no CPU hanger, 2 nos 6/16 Amps sockets, 1 no wire manager with knee covering / support panels to complete the bench.

Gas line for Second Floor (LPG - 1 Line)

OTHER ITEMS

High back executive chair, Pinnacle Leather Model EHS-HAL or equivalent

Office Chair, Medium back, Alpha MB or equivalent

Office chair, Medium back, Advantage MB or equivalent

Dining chair, s/s frame and wooden seat

Ducting for extraction in chemicals and instrument area (First Floor)

Ducting for extraction in chemicals and instrument area (Second Floor)