PR.NO- 394/24-25 Providing pipe line and motor pump set to kattile kulam drinking water project in ward 21 (SCP)

Amount

pump house

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.6.2.1:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

50.13.1:9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

10.5.2:Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using flats 30x6 mm for diagonal braces and central cross piece

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

Pipe line and Motor pump set

OD331285/2024-2025:Supplying and erection of electrically driven best quality reputed makeISI marked , open well/bore well submerssible pump set having bronze impeller stainless steel shaft capable of discharging required lpm against a total required head including all accessories such aspanel board, main wsitch, suitable starter , suitable size of flat submerssible cable, wiring materials delivery pipe for open wellelectrification charges etc.complete.The warranty shall be for a minimum period of two years including all fittings. (delivery pipe up to 10m cable , foot valve, , panel board, with main switch , fuses,ELCB, starter, earthpipe etc. (As per KWA /HO/SP/333/2011/pumps/ tvm dated 20.12.2011)A-1 HP .Details for 1HP

OD331284/2024-2025:Supplying and fixing 63 mm dia UPVC column pipe incuding all cost and conveyance Material

OD331283/2024-2025:Supplying and fixing 4 mm 3 core cable including all cost and conveyance

OD331281/2024-2025:Supply and providing good quality garware make nylon marine rope 16 mm size with required PVC tie-bad ad tieing the pump set with required outside the well

2.10.1.1:Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soilPipes, cables etc, not exceeding 80 mm dia

OD331282/2024-2025:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2

18.17.6:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :80 mm nominal bore

A.P.VINOD (BID ID -2038953)

Bidder Name

A.P.VINOD

SIDDIK