Construction of Revenue sadan cum multipurpose hall at Khajjiar Distt. Chamba

Amount

Cutting in earth work in all heights/depths in all kinds of soil such as kankar, moorum, single and decomposed or soft rock, hard rock i.e. their intermediate classifications and chiselling/wedging out of rock where blasting is prohibited including saturated soils & filling embankments etc.where necessary & disposal of exacavated unserviceable material in all leads and lifts including through mechnically transporation, the disposal of unserviceable material will be done on aproved dumping site. Any damage to the private/public property during execution will be restored by the contractor what so ever the nature of the same may be. The serviceable material will be stacked in specified dimensions in all leads & lifts as per the direction of the Engineer-in-charge

Excavation in foundations, trenches etc. in earth work in all kinds of soils such as pick work, jumper work, and chiselling / wedging out of hard or soft rock up to all depths stacking the excavated soil not more than 3 meteres clear from the edge of excavation and then returning the stacked soil in 15 cms layers, when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing off all surplus excavated earth as directed by the Engineer-in- charge.

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete including carriage of material in all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron frames 30x30x5mm so as to give a fair finish including centering, shuttering, strutting and propping, etc. with wooden battens and ballies heights of propping and centering below supporting floor to ceiling in all heights and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of material in all leads and lifts.

(a) Foundation,footings,bases of columns etc and mass concrete.

(b) Flat surfaces such as soffits of suspended floors, roofs including inclined surfaces up to any degree, landings and the like: (i) Floors, etc. upto 200 mm in thickness.

© Columns, Pillars, Posts and struts (i) Square, rectangular or polygonal in plan

(d) Stair cases with sloping or stepped soffits excluding landing.

(e) Beams, cantilevers, girders and lintels sides and soffits of beams, small ends of beams, beam haunching, cantilivers, girders, bressumers and lintels not exceeding 1 metre in depth in all heights from floors.

(f)Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like.

(g) Edges of slabs and breaks in floors and walls under 20 cm. wide.

Providing and laying cement concrete 1 : 4 : 8 (1 cement : 4 sand :8 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads & lifts.

Providing and laying cement concrete 1 : 6 : 12 (1 cement : 6 sand :12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads & lifts.

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 sand :10 graded stone aggregate 40 mm nominal size) with 15 % plum and curing complete including cost of form work in retaining walls/bresast walls, the size of plum should be 150 mm to 300 mm as per HPPWD specification including carriage of material in all leads & lifts.

Providing weepholes in brick masonry/ stone masonry/ plain reinforced concrete abutment, wing wall, return wall with 100 mm dia PVC pipe extending through the full of the structures with slop of 1(V):20(H) towards drawing face complete as per drawing and technical specification clauses 614,709,1204.3.7 including carriage of material in all leads & lifts.

Stone filling behind retaining walls including carriage of material in all leads & lifts.

Providing and laying cement concrete having strength of M-20 mixed design aggregate mechanically mixed and vibrated and curring complete excluding cost of form work and reinforcement for reinforced concrete works including carriage of material in all leads & lifts.

(a) Foundation, Footings bases of columns and the like and mass concrete.

(b) Suspended floor, roofs, landings, shelves and their support, balconies, beams, girders, bressumers and cantilevers in all heights.

© Columns, Pillars, Posts and struts upto floor two level.

(d) Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto all heights.

(e) Walls (any thickness but not less than 0.10 metre thickness)including attached pilasters buttersses,plinth and string courses etc. from top of foundation in all heights.

Providing and laying cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) reinforced concrete chajjas not exceeding 10cm. thickness upto floor two level including finishing the exposed surfaces with cement mortar 1:3 (1cement : 3 Sand) to give a smooth and even surface centring / form work and curing complete excluding the cost of reinforcement including carriage of material in all leads and lifts.

Providing Tor steel /TMT Steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire upto all heights including carriage of material in all leads and lifts.

Applying cement slurry on R.C.C . slab or cement concrete work using 2.75 kg of cement per sqm. of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete including carriage of material in all leads and lifts.

Providing throating, or plaster drip and moulding to RCC chajjas etc. including carriage of material in all leads & lifts.

Providing and laying cement concrete 1 : 8 : 16 (1 cement : 8 sand :16 graded stone aggregate 20 mm nominal size) and curing complete on slab and floor excluding cost of form work laid in depressed portion of slab/ under flooring including carriage of material in all leads & lifts.

Brick work using 2nd class common burnt clay building bricks in superstructure in cement mortar 1:6 (1 cement : 6 sand) including carriage of material in all leads and lifts.

Half brick masonry using 2nd class common burnt clay building bricks in foundation and plinth in cement mortar 1:4 (1 cement: 4 sand) including carriage of material in all leads and lifts.

Stone soling properly hand-packed filling interstices with spalls and consolidating with hand rammer including spreading watering etc.complete as per HPPWD specification. 100 mm spread thickness (finished work including materials and labour) including carriage of material in all leads & lifts

Random rubble masonry/polygonal rubble masonry (uncoursed/ brought to courses) with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 sand : 12 graded stone aggregate 20 mm nominal size) in cement mortar 1:6.(1 cement: 6 sand) including carriage of material in all leads & lifts.

Providing Sal wood work in frames of doors,windows,clerestory,windows and other frames wrought, framed and fixed in position. including carriage of material in all leads and lifts.

Providing and fixing 40mm thick single/double leaf glazed window shutter made of Sal wood having style and top rail and bottom rail 75mm width and chamferred edged moulding 20X12mm for glass panes complete including bright finished balck enamelled iron hinges with necessary screws including carriage of material in all leads and lifts.

Providing and fixing 40 mm thick sal wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws including carriage of material in all leads & lifts.

Providing and fixing Plain M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws including carriage of material in all leads & lifts.

Providing 40x3 mm flat iron hold fast 40cm. Long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm nominal size) including carriage of material in all leads & lifts.

Providing and fixing 40mm thick flush door shutters decorative type core of block board construction with frames of first class hard wood and well matched first class indian teak ply veneering with vertical grains or cross bends and face vencering on both faces of shutter factory made including carriage of material in all leads & lifts.

Providing and fixing anodized aluminium sliding door bolt as per colour and shade approved by the Engineer-in-Charge with bolts and nuts screws etc. complete including carriage of material in all leads & lifts. (a)300x16mm

Providing and fixing aluminium tower bolt (barrel type) as per colour and shade approved by the Engineer-in-Charge with screws etc. complete including carriage of material in all leads & lifts.(a) 200x 10 mm

Providing and fixing aluminium handles as per colour and shade approved by the Engineer-in-Charge with necessary screws including carriage of material in all leads & lifts. (Classic, Everite or sheel marked) (a) 125mm.

Providing and fixing M.S.hooks and eyes including cost of screws with wooden chowkhats including carriage of material in all leads and lifts.(a) 150mm.

Providing and fixing 100mm bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of material in all leads and lifts.

40 mm thick cement concrete flooring 1:2:4 (1cement : 2 sand:4 graded stone aggregate 20 mm nominal size)laid in one layer finished with a floating coat of neat Cement including carriage of material in all leads & lifts.

Providing and laying Digital tiles (any size ) 8mm thick in grey /coloured or of approved shade in skirting, riser of step and dado on a bed of 12mm thick cement mortar 1:3 (1cement:3sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including cost of tiles where required to be cut including carriage of material in all leads & lifts.

Providing and laying 20mm.thick granite stone in flooring 20mm (average) thickness base of cement mortar 1:3(1cement:3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete including carriage of materials in all leads and lifts.

Providing and laying stair case tiles size (1200x300 ) 10mm thick in grey /coloured or of approved shade in skirting, riser of step and dado on a bed of 12mm thick cement mortar 1:3 (1cement:3sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including cost of tiles where required to be cut including carriage of material in all leads & lifts.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material in all leads and lifts.

Providing and laying Duro stone vetrified tiles (any size 10mm thick) in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material in all leads and lifts.

Providing and laying Duro stone vetrified tiles (any size 8 mm thick) in grey/coloured of required shade in skirting risers of steps and dados on 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material in all leads and lifts.

Providing and fixing 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer -in-charge including carriage of material in all leads and lifts.

Providing and fixing ridges or hips 60 cm overall with 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia & prepainted G.I. limpet and bitumen washers complete with all accesoriees as required as per the direction of Engineer -in-charge including carriage of material in all leads and lifts.

Providing and fixing valley 60 cm overall 0.60mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge including carriage of materials in all leads and lifts.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in charge, (Base members of steel work shall be measured and paid separately) including carriage of material in all leads and lifts.

Steel work welded in built up sections,trusses and framed work , including cutting , hosting,fixing in position and apply ing a priming coat of red lead paint, including carriage of material in all leads and lifts.

(a) In beams joists channels,angles,tees,flats with connection plates or angle cleats as in main and cross beams ,hip and jack rafters, purlins connected to common rafters and the like.

(b) In gratings framed guard bars,ladders,railling,brackets and similar works.

Providing and fixing stainless steel railing mark-36 pipe size top-2' pipe, post pipe 1" and 3' hight in staircase including necessary fittings and positions complete as per design approved by the Engineer-In-Charge including carriage of materials in all leads and lifts.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete including carriage of materials in all leads and lifts.(i)With ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give fair and smooth surface including cleaning and surface of all dirt, dust and other foreign matter including carriage of material in all leads and lifts.(a) White enamel paint/Enamel paint other than white

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil ,grease,dirt and other foreign matter,sand papering and knotting-Ready mixed paint brushing wood primer pink,including carriage of material in all leads and lifts.

Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt ,dust and other foreign matter ,sand papering & stoping including carriage of material in all leads and lifts.(a) With enamel paint other than white.

Painting two coats(excluding priming coat on new concrete masonry/plaster surfaces with readymixed paint brushing for use on floors to give an even shade including cleaning the surface of all dirt,dust and other foreign matter and sand papering as required including carriage of material in all leads and lifts. (a) Paint other than white

6mm.cement plaster to ceiling including carriage of material in all leads and lifts.(a) In cement mortar 1:3( 1 cement : 3 sand)

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering up to all heights including arrises, internal rounded angles chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads and lifts.(a) In cement mortar 1:6(1 cement:6 sand).

20mm cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering up to all heights including arrises, internal rounded angles chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads and lifts.(a) In cement mortar 1:6( 1cement:6sand).

20mm cement plaster with cement mortar 1:4 (1 Cement :4 sand) in single coat on rough side of brick/stone masonry for interior plastering upto floor two level including arrises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads & lifts.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on ceiling and/or sloping roofs surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth.Priming coat with distemper primer including carriage of material in all leads and lifts.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth.Priming coat with distemper primer including carriage of material in all leads and lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc., including sand paper smooth complete including carriage of material in all leads and lifts.

Applying Birla white wall care putty two or more coats over plastered surface after thoroughly brushing the surfase free from mortar drops, dust, loose materials and other forign matter sand papered smooth to give final matter finish to the surface complete including carriage of materials in all leads and lifts.(i) In Wall surface / Ceiling

Providing plinth protection 50mm thick in cement concrete 1:3:6 ( 1 cement:3 sand:6 graded stone aggregate 20mm nominal size) including finishing the top surface of concrete smooth including carriage of material in all leads and lifts.

Providing under layer for plinth protection of 75 mm thick ( unconsolidated) bed of dry brick / stone aggregate 40mm nominal size well rammed and consolidated and grouted with fine sand including preparation of ground complete including carriage of material in all leads and lifts.

Constructing Course rubble hammer dressed "U" shape opensurface drain with side wall.15x22 cm in cement morter 1:6(1 cement:6sand)and inside plastering with cement plaster1:3(1 cement :3 sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 cement:5 sand :10 graded stoneaggregate of 40mm nominal size) and 7.5 cm cement concrete1:2:4(1 cement :2 sand :4 graded stone aggregate of 20mmnominal size )and finished with a floating coat of neat cement complete as per standred design including carriage of material in all leads and lifts.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mmand37mm,at1200mm centre to centre,one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of25x10x0.50mm of required length with nuts &bolts of required siz and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200mm centre to centre,to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I.wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with (a) 12.5 mm thick tapered edge gypsum plain board conformingtoIS:2095-(PartI):2011 (Board with BIS certification marks) including carriage of material in all leads and lifts.

Providing and fixing to wall ceiling and floor Plytheline – Aluminium - Polyethylene (PE-AL-PE) composite pressure pipe confirming to IS 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capble to withstand temperature up to 80 degree C, including all special fittings composite materials (Engineering plastic blend brass insertes where ever required) e.g. elbows, tees, reducers, couplers and connectors etc. with clamp at one metre spacing.This includes testing of joints complete as per direction of Engineer-In-Charge including carriage of material in all leads and lifts. (i) 1216 (16 mm O.D. pipe)

ii) 1620 (20 mm OD pipe).

Providing and fixing polythene water storage tank for storage of water up to all heights keeping water hygenic and safe for drinking etc.moulded to seamless perfection from FDA approved grades of polythene (LDPE / HDDE / CIDPE) confirming to BIS-12701-1989 with 40 mm nominal bore galvanised steel scoure tube with fittings 25mm nominal bore galvanised mild steel over flow tube with fitting & mosquito proof coupling of approved municipal design 15mm nominal bore ball valve and as per direction of Engineer-in- charge including carriage of materials in all leads and lifts. (i) 1000 liters capacity

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipes complete including carriage of materials in all leads and lifts.

Providing and fixing 110mm x 75 mm PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete.

Providing and fixing high pressure a PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts.(a) 90 mm dia

(b)110 mm dia

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete.(a) 90 mm dia

(b)110 mm dia

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.(a) 110mm dia.

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete(a) 90 mm dia

(b)110 mm dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc., complete, including carriage of material in all leads and lifts.(a) 90 mm dia

(b)110 mm dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc, complete ,including carriage of material in all leads and lifts.(a)90 mm dia

(b)110 mm dia

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S.Brackets painted white including cutting holes and making good the same but excluding fitting. including carriage of material in all leads and lifts.and confirming to BIS specification.i) 610 x 510 mm with bowl depth 200 mm.

Providing and fixing PVC ‘P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete. including carriage of material in all leads and lifts.(a) 110 mm dia.

Providing and fixing coloured / white high density polyethylene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of material in all leads and lifts.

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube including carriage of material in all leads and lifts.and confirming to BIS specification.

Providing and fixing 100 mm dia chromium plated grating of superior quality for floor, gully or nahani trap including carriage of material in all leads and lifts.and confirming to BIS specification.

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete. (a) 90 mm dia

(b)110 mm dia

Providing and fixing vitreous china water closet squatting pan ( European type W.C.pan ) with integral "p" or "s" trap including jointing the trap with soil pipes in cement mortar 1:1 ( 1 cement:1 sand) seat and cover to be measured and paid for separatly including carriage of material in all leads and lifts.and confirming to BIS specification.Anglo Indian ( universal closet)

Providing and fixing white plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers. (Hindware, Cera.)

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings including carriage of material in all leads and lifts.(a) Flat back (i) 630mmx450mm

Providing and fixing 32mm dia C.P. brass waste for wash basin or sink:, and confirming to BIS specifications. including carriage of material in all leads and lifts.(ESS-ESS/ CZAR /NOVA)

Providing and fixing 32 mm dia M.I. Union for wash basin or sink including carriage of material in all leads and lifts.

Providing and fixing 600mmx450mm bevelled edge mirror of superrior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brassscrews and washers including carriage of material in all leads and lifts and confirming to BIS specifications.(Atul, Modi Guard, Saint Gobains)

Providig and fixing C.P. brass towel rail complete C.P.brass brackets ( fixed to wooden plugs with C.P. brass screws , and confirming to BIS specifications,600mm x20mm, including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providig and fixing C.P. brass towel ring complete C.P.brass brackets ( fixed to wooden plugs with C.P. brass screws , and confirming to BIS specifications including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providing and fixing C.P. brass soap dish with C.P. brass brackets fixed to wooden plugs with C.P. brass screws, and confirming to BIS specifications,including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providing and fixing 100mm dia C.P. Brass shower rose with 15mm or 20mm inlet including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Proving and fixing C.P. brass bib tap with capstan head15mm dia, long body and confirming to BIS specifications, including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Proving and fixing C.P Brass pillar tap with Capstan head15mm dia, and confirming to BIS specifications, including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providing and fixing Mixer for kitchen sink with casted swinging spout at top confirming to BIS specifications, including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providing and fixing C.P. connection pipe with brass unions including carriage of material in all leads and lifts.45cm length 15mm nominal bore.(ESS-ESS/CZAR/NOVA)

Providing and fixing C.P.brass angle valve 15 mm without nuts and pipe including carriage of material in all leads and lifts confirming to B.I.S. specification.(ESS-ESS/CZAR/NOVA)

Providing and fixing C.P. stop cocks 15 mm including carriage of material in all leads and lifts confirming to B.I.S. specification.(ESS-ESS/CZAR/NOVA)

Providing and fixing G.I./M.I Union (confirming to B.I.S specification) including carriage of material in all leads and lifts.(a) 15 mm dia

(b)20 mm dia

Providing and fixing brass full way valve with wheel (confirming to B.I.S specification) including carriage of material in all leads and lifts.(a) 15 mm dia

(b)20 mm dia

Providing and fixing PVC Cowl ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.(a) 110 mm dia

Providing and fixing stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5 and water tight C. I. cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.53kg and frame to be not less than 2.72kg.(I) Square Mouth Traps (i) 100mmx100mm size P type including carriage of material in all leads and lifts

Constructing man hole with RCC top slab in 1:2:4 mix (1cement:2sand: 4graded stone aggregate 20mm nominal size ) Foundation concrete 1:4:8 (1cement : 4sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortor 1:3(1 cement:3 sand) finished with a floating coat of neat cement and including making channels in cement concrete 1:2:4 mix (1cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testng including carriage of materials in all leads and lifts. (a) Inside size 800mm x 800mm and 500mm deep including S.F.R.C. frame and cover medium duty 500mm diametre internal size.With 200mm thick walls of brick masnoey using common burnt clay building bricks in cement mortor 1:3 (1 cement :3sand) .including carriage of material in all leads and lifts

Providing 200 mm wide cast iron Rungs with chequered or ribbed non slip surface including fixing in manholes with 200 mm x 200 mm x 100 mm cement concrete 1:3:6 (1Cement:3 Sand: 6graded stone aggregate 20 mm nominal size) including carriage of material in all leads and lifts

Suppling and fixing 455 x 610 mm light duty rectangular cast iron cover with frame weight 38 kg (single seal pattern) including carriage of material in all leads and lifts.

Construction of soak pit 2.50 metre diametre 3.00 metre deep with 45x45cm dry brick masonry of class designation 75mm S.W. drain pipe 100mm diameter 1.80 metre long as per standard design with FPS including carriage of material in all leads and lifts.

Amarpreet Govt Contractor