REPAIRS / REPLACEMENT OF GATE, FENCING , PATHS, WALLING, HARDSTANDINGS ETC AT DEMSY ROAD, COD ROAD AREA UNDER AGE B/R (EAST) AT GE DEHU ROAD.

Amount

Dismanteling fencing wire mesh , any type

Dismanteling post, struts , (wood , steel or Rcc) any section incl. taking out embede portion in concrete or brickwork and making disturbed portion good

Excavation in post holes or similer holes each nexc. 0.5 cum getting out returning filling in and ramming earth around in layers n. exc 25 cm,watering , and removing surplus soils to a distence nexc 50m and making good surface in hard soils, complete all as specified.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate ) as in foundation concrete for fencing post.

S&F angle iron fencing post and struts including cutting tops to shape as directed, drilling holes, notching for wire etc , flat iron fillets ( for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-410-0 or Fe 310-0 anyu size.

S&F MS Screw bolts ( machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut length exc. 5 cm but not exc 10 cm long 11 to 15mm dia of shank.

S&F flat iron straps to chain link fencing including drilling bolting or riveting etc as directed

Supply only chain link MS galvanised fencing incl line wire 100x100mm mesh (12 gauge) size and any type of strands, rails, straining bolts etc incle provn of binding wire all complete

Supply only chain link MS galvanised fencing incl line wire 50x50mm mesh (12 gauge) size and any type of strands, rails, straining bolts etc incle provn of binding wire all complete

Fixing only chain link fencing any mesh, size and type to any type of standards, rails, straining bolts etc incl provn of binding wire

M&L for round bars 10mm dia and over cut to length bent to shape required incl cranking, bending spirally for hoping for columns, hooking ends and binding with and incl MS Wire (annealed) not less than 0.9mm dia or securing with clips.

S&F GI two strand, steel barbed wire 2.24mm dia, narbed with 2mm dia barbs @ 75mm spacing and straining and fixing to any type of standard rail, straining bolts, inlc securing or tying at crossing with and provn of galvanised mild steel wire staples or steel pins etc. All as specified (Each line of wire to be measured.)

M&L two coats of synthetic enamel paint to new steel surfaces over a coat of red oxide primer surfaces of any description exc 10 cm in witdth or girth

M&L preparing new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer surface area not exc. 10cm in width or girth

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar.

Demolition of cement concrete (unreinforced) of any description and in any position not ohterwise specifically provided for .complete all as sspecified

M&L PCC type D2 1:4:8 (40 mm Gr. Agg ) 75mm thick as in sub base.

M&L for laying machine pressed precast concrete interlocking reflective coloured pavers block any shape and size confirming to IS 15658-2006 of 55mm to 60mm thick, M-35 Grade over 30mm thick sand layer watering and ramming all as specified.

M&L Chequared Cement Concrete (reflactive rubber molded) Tiles 30 CM x 30 CM X 25 mm th set and jointed in cement slurry and pointed in neat grey cement & pigment in floors reflective coloured over screed bed 15 mm thk in cm 1:6.

Material and labour for 20 mm thick granite stone machine cut (table rubbed and polished) bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigments to match the shade of granite stone including grinding and polishing, complete all as specified.

Labour only for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as specified and directed

M&L machine cut kota stone slab flooring 20-25mm thick over and including cement screed based 15 mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl cutting polishing and rubbing complete.

Dismantling floor, hearth or wall tiling marble etc including cement mortar bedding,and not backing including removing serviceable tiles to stores and rubbish off the premises.

M&L for 40 mm thick plain cement concrete 1:2:4 type B-1 using (20 mm graded stone aggregate) as in sub base for leveling course.complete all as specified.

M&L for joint free non-skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile exc 0.11sqm but n.exc 0.18sqm, of approved colour in floors, set and jointed in neat cement slurry and pointed with coloured cement to match the tile colour. over 15mm thick screed bed in CM (1:6) for floor.

Ditto above item No 25 but on skirting over 10 mm th rendering in CM 1:4 complete.

M & L Glazed ceramic coloured tiles 300 mm x 450 mm x 6 to 7 mm thick,as in skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 10 mm thick rendering in CM (1:4) complete.

M & L Glazed ceramic coloured tiles 300 mm x200 mm x 6 to 7 mm thick,as in skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 10 mm thick rendering in CM (1:4) complete.

M&L for vitrified coloured tiles 10mm th (square/rectangular) polished area of each tile 0.30 sqm but n exc 0.42 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm th screed bed in CM 1:6 complete

Ditto above item No 29 but on skirting over 10 mm th rendering in CM 1:4 complete.

M&L for PCC type B1(1:2:4, using 20mm graded stone aggregate) as in bed blocks/coping/ edging all as specified and directed.

M&L for cement concrete 1:3:6 type C2 (using 40mm graded stone agg.) as in plinth protection 75 mm thick finished top surface even and smooth with out using extra cement

M & L for Hard core of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for 100 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) in sub base for hard standing complete all as specified and directed.

M & L for Cement concrete work in pavement/hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less completed all as specified

Finishing surface of concrete roads, pavements etc by belting/brooming complete all as specified and directed.

M & L for forming 12 mm thick expansion joints 150 mm deep, filled with preformed bituminous filler and top 30 mm primed and sealed with sealing compound grade 'A' complete all as specified and directed.

M & L for forming contraction (Dummy) joints 65 mm deep x 10 mm wide, filled with sealing compound grade 'A' complete all as specified and directed.

Demolition of Brick work built in cement mortar including all quioins, arches, pillars, etc.

M & L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in1:6 all as specified and as directed.

M & L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for cement conceret 1:2:4 Type B-2 Using 40 mm graded stone aggregate as in surface channel and drain bed wall and floor etc.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.

M & L 15 mm thick cement plaster on brick wall in cement morat 1:4 and plastered surfaces shall be even and smooth without using extra cement complete.

M & L 15 mm thick cement plaster on brick wall in cement morat 1:6 and plastered surfaces shall be even and smooth without using extra cement complete.

M&L for preparing new plastered surfaces & applying two coats of cement base paint on walls. complete all as specified and directed.

H S TAKHI

DR J S CHADHA AND SONS

M/S B.A. GAIKWAD

RAMESH PATIL

Star Construction

D J Construction

M/S OMKAR DEEPAK DHAVAN

S.R.M.K Enterprises