Civil Works and Installation of Power Backup System at Santhigiri Ayurveda Siddha Research Centre and Skill Development Training Institute, Saket, New

S. No. Description Amount (Rs.)

1 Compound Wall & Gate Work 1207418.37

2 Rain Water Harvesting System 551040.00

3 Underground Sump 254516.32

4 Power Backup System 841114.00

BOUNDARY WALL & GATE WORK

S.No. DSR No. Item Description Unit Rate Qty. Amount

Demolishing R.C.C. work manually/

by mechanical means including

stacking of steel bars and disposal of

unserviceable material within 50

metres lead as per direction of

Engineer - in- charge. Cum 3657.79 2.80 10241.81

Demolishing brick work manually/ by

mechanical means including stacking

15.7 of serviceable material and disposal

of unserviceable material within 50

metres lead as per direction of

Engineer-in-charge.

Earth work in excavation by

mechanical means (Hydraulic

excavator)/ manualmeans over areas

(exceeding 30 cm in depth, 1.5 m in

width as well as 10 sqm on plan)

including getting out and disposal of

Filling available excavated earth

(excluding rock) in trenches, plinth,

sides of foundations etc. in layers not

4 2.25 exceeding 20cm in depth,

consolidating each deposited layer

by ramming and watering, lead up Cum 201.88 59.636 12039.31568

Centering and shuttering including

strutting, propping etc. and removal

5 5.9.1 Foundations, footings, bases for columns Sqm 403.91 18.48 7464.33996

Lintels, beams, plinth beams, girders,

bressumers and cantilevers Sqm 758.49 31.00 23513.25

7 5.9.6 Columns, piers, abutments, pillars, posts and Sqm

Providing and laying in position

4.1 cement concrete of specified grade

excluding the cost of centering and

1:4:8 (1 Cement : 4 coarse sand

8 4.1.8 (zone-III) derived from natural

sources : 8 graded stone aggregate Cum 7016.36 7.44 52201.7184

Digitally signed by RAJ PAL

Providing and laying in position

machine batched and machine mixed

design mix M-25 grade cement

concrete for reinforced cement

concrete work, using cement content

as per approved design mix,

including pumping of concrete to site

of laying but excluding the cost of

centering, shuttering, finishing and

reinforcement, including admixtures

in recommended proportions as per

IS: 9103 to accelerate, retard setting

of concrete, improve workability

without impairing strength and

durability as per direction of

5.33.1 All works upto plinth level

Concrete of M25 Grade with

minimum cement content of 330 Cum 9789.89 8.04 78740.11

5.33.2 All works above plinth level upto

Concrete of M25 Grade with

minimum cement content of 330 Cum 10156.21 2.97 30163.94964

Steel reinforcement for R.C.C. work

including straightening, cutting,

5.22 bending, placing in position and

binding all complete upto plinth level

Thermo-Mechanically Treated bars

of grade Fe-500D or more Kg 111.09 804.30 89346.07

Steel reinforcement for R.C.C. work

including straightening, cutting,

5.22A bending, placing in position and

binding all complete above plinth

Thermo-Mechanically Treated bars

of grade Fe-500D or more Kg 111.09 356.4 39590.87

Brick work with common burnt clay

machine moulded modular bricks of

class designation 12.5 in exposed

brick work including making

horizontal and vertical grooves 10

mm wide 12 mm deep complete in

13 6.28.1 From ground level upto plinth level Cum 7207.32 12.12 87359.95

14 6.28.2 Above plinth level upto floor V level Cum 9240.23 21.39 197648.58

15 mm cement plaster on the rough

side of single or half brick wall of mix

Finishing walls with Acrylic Smooth

exterior paint of required shade :

New work (Two or more coat applied

16 13.46.1 @ 1.67 ltr/10 sqm over and including

priming coat of exterior primer Sqm 165.42 291.40 48202.8052

17 NS Electric Work & Light Fittings Nos 1120.00 28.00 31360.00

Steel work welded in built up

sections/ framed work, including

cutting, hoisting, fixing in position

and applying a priming coat of

Digitally signed by RAJ PAL

In gratings, frames, guard bar,

ladder, railings, brackets, gates and Kg 177.78 1500.00 266667.00

Rain Water Harvesting Pit

S.No. Item Description Unit Rate Qty. Amount

Construction of Rain Water

harvesting pit (size 5 m dia x 3 m

depth) including all associated civil

works of top slab, backfilling,

disposal of surplus excavated earth

UNDERGROUND SUMP

S.No. DSR No. Item Description Unit Rate Qty. Amount

Earth work in excavation by

mechanical means (Hydraulic

excavator)/ manualmeans over areas

(exceeding 30 cm in depth, 1.5 m in

width as well as 10 sqm on plan)

including getting out and disposal of

excavated earth lead upto 50 m and

lift upto 1.5 m, as directed by

Engineer-in-charge.

1 2.6.1 All kinds of soil Cum 182.83 25.20 4607.19

Centering and shuttering including

strutting, propping etc. and removal

of form work for :

2 5.9.1 Foundations, footings, bases for columns Sqm 403.9145 2.85 1151.156325

Walls (any thickness) including

3 5.9.2 attached pilasters, butteresses,

plinth and string courses etc. Sqm 867.775 34.20 29677.91

4 5.9.3 Suspended floors, roofs, landings,

balconies and access platform Sqm 955.0675 12.00 11460.81

Providing and laying in position

cement concrete of specified grade

4.1 excluding the cost of centering and

shuttering - All work up to plinth

1:4:8 (1 Cement : 4 coarse sand

(zone-III) derived from

natural sources : 8 graded stone

aggregate 40 mm

nominal size derived from natural

Digitally signed by RAJ PAL

Providing and laying in position

machine batched and machine mixed

design mix M-25 grade cement

concrete for reinforced cement

concrete work, using cement content

as per approved design mix,

including pumping of concrete to site

of laying but excluding the cost of

centering, shuttering, finishing and

reinforcement, including admixtures

in recommended proportions as per

IS: 9103 to accelerate, retard setting

of concrete, improve workability

without impairing strength and

durability as per direction of

Engineer-in-charge.

(Note :- Cement content considered

in this item is @ 330 kg/cum. Excess/

less cement used as per design mix is

payable/recoverable separately).

5.33.1 All works upto plinth level

Concrete of M25 Grade with

6 5.33.1.1 minimum cement content of 330

Steel reinforcement for R.C.C. work

5.22 including straightening, cutting,

bending, placing in position and

binding all complete upto plinth level

Thermo-Mechanically Treated bars

of grade Fe-500D or more Kg 111.0855 734.40 81581.19

15 mm cement plaster on the rough

13.2 side of single or half brick wall of mix

Digitally signed by RAJ PAL

Providing and applying integral

crystalline slurry of hydrophilic in

nature for waterproofing treatment

to the RCC structures like retaining

walls of the basement, water tanks,

roof slabs, podiums, reservior,

sewage & water treatment plant,

tunnels / subway and bridge deck

etc., prepared by mixing in the ratio

of 5 : 2 (5 parts integral crystalline

slurry : 2 parts water) for vertical

surfaces and 3 : 1 (3 parts integral

crystalline slurry : 1 part water) for

horizontal surfaces and applying the

same from negative (internal) side

with the help of synthetic fiber

brush. The material shall meet the

requirements as specified in ACI-212-

3R-2010 i.e by reducing permeability

of concrete by more than 90%

compared with control concrete as

per DIN 1048 and resistant to 16 bar

hydrostatic pressure on negative

side. The crystalline slurry shall be

capable of self-healing of cracks up

to a width of 0.50 mm. The work

shall be carried out all complete as

per specification and the direction of

For vertical surface two coats @ 0.70

kg per sqm per coat Sqm 487.09 46.20 22503.4194

Total 254516.32

POWER BACKUP SYSTEM

S. No. Description Unit Qty Rate Amount

Supply, installation, Testing &

Commissioning of 'Silent Type Diesel

Generating set as per CPCB IV + or

better norms along with having

Prime Power Rating of KVA as below,

415 volts at 1500 RPM, 0.8 lagging

power factor at 415 V suitable for 50

Hz, 3 phase system & for 0.85 Load

1 Factor, including testing at factory

and site with fuel, load for test and

other necessary arrangements

Complete as per CPWD

specifications, should

have QR code which should contain

drawing, test report OEM

manual,GeoTag of manufacturing

location, rating plate as per relevant

IS Code etc. and consisting of the

Digitally signed by RAJ PAL

(A) Diesel Engine:

Turbocharged Diesel engine 4 stroke

water cooled, multi cylinder,

dynamically balanced fly wheel,

electric start of suitable BHP at 1500

RPM suitable for above output of

alternator at 40 Degree C, 50% RH &

at 1000 Meter MSL, capable of taking

10% over loading for one hour after

continuous operation. The engine

will be with Electronic governor, Dry

typeAir filter with service indicator,

first filling of engine fuel (after

commissioning) lubricating Oil,

Coolant and other consumables

complete with all the required

accessories, the Electronic governor

shall be as per ISO 8528.The engine

shall comply to the latest CPCB

norms (CPCB IV + or better) and

Conforming to BS 5514, BS 649, IS

10000, IS 10002, IS 13018 and as per

CPWD specifications.

(B) Engine mounted Instrument

Panel fitted with and having digital

display for following:

(i) Start-stop switch with key

(ii) Water temperature indication

(iii) Lubrication oil pressure

(iv) Lubrication oil temperature

(v) Battery charging indication and

Voltage indication

(vi) RPM indication

(vii) Over speed indication

(viii) Low lubricantion Oil trip

(ix) Engine Running Hours indication

Digitally signed by RAJ PAL

(C) Alternator:

Synchronous alternator rated of

appropriate KVA, 415 volts at 1500

RPM, 3 phase 50 Hz, AC supply with

0.8 lagging power factor at 40

Degree C, 50% RH & at 1000 Meter

MSL. The alternator shall be having

Screen ProtectedDrip Proof (SPDP)

enclosure IP23, brushless,

continuous duty, dynamically

balanced rotor, capable of taking

10% over loading for one hour after

12 hours of continuous operation,

self cooled,self-excited and self-

regulated through AVR conforming

to IS13364(Part 2)/IS: 4722/BS 2613

suitable for tropical conditions and

with class- H insulation.

(D) Base Frame & Foundation:

Both the engine and alternator shall

be mounted on suitable base frame

made of MS channel with necessary

reinforcement which shall be

installed on suitable cement

concrete foundation and vibration

isolation arrangement as per

recommendations of manufacturer.

Daily service fuel tank of suitable

liters capacity as per CPWD

Specifications, fabricated out of 3

mm thick M.S. sheet complete with

all standard accessories and fuel

piping between fuel tank and diesel

engine with MS class 'C' pipes of

suitable dia. Complete with valves,

level indications & accessories as

required as per specifications.

(F) Exhaust System:

Dry exhaust manifold with hospital

type exhaust silencer and catalytic

Digitally signed by RAJ PAL

(G) Starting System:

12V/24V DC starting system

comprising of starter motors: voltage

regulator and arrangement for initial

excitation complete with suitable

numbers of batteries (180 AH

capacity lead acid SMF type) as

required as per specifications. The

battery shall be housed inside the

acoustic enclosure

(H) Acoustic and weather proof

enclosure with arrangement for fresh

air intake for cooling of the engine &

alternator, extraction, discharging

hot air in to the atmosphere and the

temperature rise inside the

enclosure, noise level

outside enclosure. The acoustic

enclosure should be suitable for

cable connection/connection

through bus-trunking. Such

arrangements on acoustic enclosure

should be water proof & dust-proof

conforming to IP-65 protection. The

enclosure shall be as per CPCB IV +

or better norms etc. and as per

CPWD specifications.

Free standing floor mounted IP 42

automatic mains failure control

panel including auto by-pass, suitable

for KVA as below for silent type DG

set complete with relays, timers, set

of CTs for metering & protection and

energy analyser to indicate currents,

phase and line voltages, frequency,

power factor, KWH, Kilo Volt Ampere

Reative Hour (KVARH), KVA (Phase &

Total), KW & provision for overload,

short circuit, restricted earth fault,

under frequency, power (aluminum)

and control (copper ) cabling of

suitable size upto 15 meter between

AMF panel, LT Panel and DG Set

including connection interconnection

etc. as required, all complete and

and communication/ Ethernet

/RS485/SNMP port open protocol for

BMS integration including suitable

software, the panel shall be of DG

Set OEM make etc. as per approved

by Engineering in charge and

including the following:

Digitally signed by RAJ PAL

1. Suitable numbers and appropriate

capacity 4 pole motorised

electrically operated draw out with

cradle type 3 position ACB/ MCCB

with electronic release for O/C & E/F

and shunt trip.

2. Auto/Manual/Test/Off selector

3. Protection for under and over

voltage phase reversal (2 nos Over

voltage relay, 2 Nos. reverse power

relay and 2 Nos. under voltage relay).

4. 3 Sets of current transformers 15

P10 accuracy for protection and 15

VAclass-I for metering

5. Energy analyser unit to indicate

current, Voltage( L-N & L-L), kW, kVA

(Phase & Total), Frequency, KWH, PF.

6. LED Indicating lamps for load on

mains and load on set.

7. Fuse/ MCB for instruments.

8. Battery charger, complete with

transformer/ rectifier, D.C. voltmeter

and ammeter, selector switch for

trickle, off and boost and current

9. Main supply failure monitor

10. Supply failure timer.

11. Restoration timer

12. Control unit with three impulse

automatic engine start/stop and

failure to start lockout.

13. Impulse counter with locking and

reset facility.

14. ON/OFF/Control circuit switch

15. Audio/Video annunciation for

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning

16. Protection for over/under

Frequency, Loss of AC sensing, Over

Current, Unbalancing load with

suitable number of relays and

17. Maintenance notification based

on Engine Run Hour & due date.

Digitally signed by RAJ PAL

18. Load Management through PLC

to achieve auto opening and closing

of incomer breakers, bus coupler

switching of essential panel ,

interlocking providing signal to AMF

Panel for load status and AMF shall

give command to DG Set to auto

start / auto stop depending upon

load status and requirement etc. and

necessary hardware and software

required to perform the operation

shall be provided by the contractor

including all control wiring.

Digitally signed by RAJ PAL