SPECIAL REPAIR TO BLDG NO T31 T32 T128 T129 OTM ACCN AT SUNDERBANI UNDER GE NORTH AKHNOOR

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil as directed by Engineer-in-Charge.

Cement concrete type C-2 1:3:6 (40mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete all as specified.

Dismantling wall and ceiling boards, fibre pulp insulation etc or insulation boards/ slabs / blankets, any thickness, including cover fillets, all as specified.

GI frame work 605 x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soft it at approx x 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 centre to centre including 4 mm thick designer building board in grid fixed in position complete all as specified.

Dismantling asbestos cement (corrugated or semi corrugated etc) sheet in roof covering including ridges, all as directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof overing/ cladding to wall, fixed with self tapping screws incl ridge all as specified and directed by Engr-In-Charge.

Ditto as per item No 07 above but plain sheet.

Dismantling mild steel work of any description complete all as specified and directed.

Rolled mild steel section as in main and cross beams, hip and jack,rafters, purlins, where connected to common, rafters and running rails and guiders for sliding doors: fixed with angle cleats or other connecting platesconforming to grade Fe410-W (Gde E-250) quality 'A' all as specified

Mild steel flat iron for wind ties for roof including securing bolts, necessary drilling bolting or riveting etc and similar work conforming to Fe-210 Gde E-165

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n exc 1.5 Sqm each ,complete all as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exc 1.5 Sqm and n.exc 4.00 Sqm each ,complete all as specified.

Demolition of stone/brick masonary built in cement/ cement lime mortar complete all as specified and directed.

Walling of random rubble stone masonery coursed, well bonded,bedded and solidly hearted, built in CM 1:4 complete all as specified and directed.

Ditto all as per item No 15 but except stone.

Taking down cement plaster from brick or stone walls incl racking out joints hacking for key, scrubbing down with water etc.

Rendering 15 mm thick in cement and sand mortar 1:4 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge

Rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified.

Supply only integral water proofing compound.

25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate, as in sub base of floor complete all as specified and as directed by Engineer-in-charge.

Non skid coloured ceramic tiles grade B-IIa 7mm to 8mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in light shade floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces incl 15mm thick screed bed/bedding layers in cm 1:4 all as spd & directed.

Ditto all as per Item No. 22 but on vertical surfaces such as skirting, dado and risers to steps etc over & including 10 mm thick rendering in CM 1:3 complete all as specified.

Machine cut kota stone slab flooring 18-22mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade or the slab including rubbing and polishing complete including 15 mm thick in CM 1:6 screed for laying Kota Stone complete all as spd.

Ditto all as per item No. 24 but as in riser of steps ,skirting, dado and pillar including 10 mm thick in CM 1:3 rendering for Kota Stone complete all as spd.

Pressed steel frames factory made for doors out of 1.25mm thick PBI sheet with one of more rebates including necessary flat iron lugs, hinges, lock strike plate, hinges etc complete, size of frame 125x60mm including tarring ends and back of chowkats and lugs complete all as specified and directed

Pressed steel frames factory made for doors out of 1.25mm thick PBI sheet with one of more rebates including necessary flat iron lugs, hinges, lock strike plate, hinges etc complete, size of frame 105x60mm including tarring ends and back of chowkats and lugs complete all as specified and directed

PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame complete all as specified and as directed by Engineer-in-Charge

35mm thick, IInd class hard wood plain, framed, panelled factory made shutters (two panel) with lock rail and panel of 9mm BWP commercial ply 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified & as directed by Engineer-in-Charge

35 mm thick, 2nd class hard wood, glazed & skeleton factory made shutters, open rebated and prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.24(a) complete all as specified and as directed by Engineer-in-Charge. Note for item Nos 29 & 30 here-in-before: - 1.The contractor may use/provide Ist class hard wood “SHISHAM” for manufacturing of factory made shutters in lieu of IInd class hard wood without any extra cost to the govt. 2. The shutters shall be procured from any of the approved manufacturers from the list given in Approved make/ manufacturer 3. Glass or wire cloth shall be measured and paid for separately under appropriate items of this schedule).

200 mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed by Engineer-in-Charge.

250 mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete.

Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified.

Aluminium handles fabricated type anodised of size 150 mm long ISI marked complete all as specified and as directed by Engineer-in-Charge.

Factory made steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay complete with glazing bars, dovetailed or welded and also including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified.

All as per item No 35 here-in-before but without glazing bars.

Frame work such as grills, frame, gratings etc ends of bars shouldered and/or riveted, welded or forged into spikes, framed guard bars and work conforming to Fe 410-0.

Glazing with sheet, 3mm thick, ordinary quality and glazing with oil putty and glazing pins in squares not exceeding 0.5 Sqm in each pane.

Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, or galvanized wire staples all as specified & directed.

150 mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate, ISI marked complete all as specified and as directed by Engineer-in-Charge.

50 mm thick PCC type C-1 1:3:6 (using 20mm graded stone aggregate) as in plinth protection laid in bays complete including 75mm thick consolidated hard core of broken stone over rammed earth finishing the surface of concrete topping even & fair, without using extra cement filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand (all by weight) complete all as specified and as directed by Engineer-in-Charge. Note :- The rate quoted shall be deemed to include for use and waste of form work/screed strips and to divide the area in panels.

Curtain rail ,20 mm dia anodised aluminium alloy, cromium plated fixed with braket, incl taking down of old curtain rods, all as directed.

Preparing new surfaces, plastered or unplastered walls and applying two coats of oil bound distember over a coat of chalk whitening

Complete removal of existing old treatment plastered or unplastered walls and applying two coats of oil bound distember over a coat of chalk whitening

Preparing new surfaces, plastered or unplastered walls and applying two coats of cement base paints over one coat of white wash all as specified and directed.

Preparation of old painted surfaces of walls by washing, rubbing, stopping, brooming down with steel wire brushing scrapping down smoke roots, moulds salts and applying two coats of cement base paint all as specified and directed.

Preparation of new steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide premier complete all as specified.

Preparation of old painted surfaces of steel of any description exc 10 cm width or girth and applying one coat of synthetic enamel complete all as spd and directed.

Preparation of new untreated wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and painting with two coats of synthetic enamel paint over a coat of pink primer complete all as spd and directed.

Chequerred cement concrete tiles 25 cm x 25 cm x 22mm thick with grey and no pigment, set, jointed and pointed in neat cement slurry in floors including 20 mm thick screed bed in cement and sand mortar 1:6 over 75mm thick PCC type C-2 1:3:6 using (40mm graded aggregate) complete all as specified.

Taking down carefully, copper / aluminium conductor unserviceable / perished point wiring (any type) for light/ fan/ light socket or power socket etc complete with fittings such as switches, sockets, ceiling roses, pendant holders, bracket holder, light fittings, regulators etc, including making good to disturbed surfaces of wall/floor etc, complete, all as specified & directed.

Taking down main switches, distribution boards etc of any type and capacity along with the existing boards, and removing the same from site and making good the disturbed surfaces/portion of walls etc. all as directed.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 1.5 Sqmm drawn into and including PVC casing and caping 'ISI marked' of 20/30mm size as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories, fixing arrangements on wall /roof/floor by means of drilling by heavy duty hand drill and fixing with PVC rawl plug and screws including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one light/fan point controlled by one way switch, complete all as specified & directed.

All as per Srl item No. 54 above but for one 3/5 pin 5 Amps socket outlet on same board .

All as per Srl item No. 54 here-in-before but for one 3/5 pin 5 Amps socket outlet on independent board.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 2.5 Sqmm drawn into and including PVC casing and caping 'ISI marked' of 20/30mm size as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories, fixing arrangements on wall /roof/floor by means of drilling by heavy duty hand drill and fixing with PVC rawl plug and screws including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 2.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one 3/5 pin socket outlet 15 Amps independent, complete all as specified & directed. Notes for Srl Item No. 54 to 57 (i) Unit rate includes for cutting chases whereever required and sinking for boxes, making good to walls / floors etc., complete, including white wash / colour wash as directed. (ii) Uniform coding of wiring i.e red / yellow / blue for phase black for neutral and green for earth is to be maintained.

Switch socket combination, two in one, 6 pin type, 5 & 15 Amp, flush type universal, complete all as specified & directed.

Switch socket combination, two in one, 5 pin type, 5 Amp, flush type universal, complete all as specified & directed.

Socket outlet two in one, 5 pin type, 5 Amp, flush type, complete all as specified & directed.

Ceiling rose surface type, bakelite 65mmx50mm, 3 terminals, complete all as specified & directed.

Switch piano flush type 5 Amps 240 Volt, single pole one way, complete all as specified & directed.

Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified & directed.

LED lamp in white colour of 7 watt, base Cap B-22, complete all as specified & directed. Make : Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya/ Havells

Sheet metal enclosure, factory made for DBs, protection class IP-36, phosphatised powder coated, double door when MCB's to be used, single pole & neutral, 240 volts with 200 amps rated copper bus bar & neutral link earthing stud, 8 way, complete all as specified & directed.

MCB, single pole & neutral, 40 Amp, AC, 10 KA repturing capacity, 240 Volt, 'C' series, complete all as specified & directed.

MCB, single pole, 6 to 32 Amp, AC, 10 KA repturing capacity, 240 Volt, 'C' series, complete all as specified & directed.

Fan regulator, deluxe socket type (electronic step type) for 1200/1400 sweep AC ceiling fan, complete all as specified and directed.

Earthing of galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr depth below normal ground level) with top edge of earth not less than 1.5 mtr below normal ground level, surrounded on all sides by 150mm thick charcoal & common salt starting from ground below earth plate upto 150mm above GI plate in alternate layers connected to and including earth lead wire 4.0mm (8SWG) by means of steel bolts, nuts, check nuts and washers, test point made of GI strip 40x8mm, 10cm long PCC 1:2:4, type B-1 in pit with precast RCC 1:2:4 type B-1 in cover reinforced with XPM not less than 4 Kg per Sqm with 15mm bore GI light grade protection pipe, 20mm bore GI medium grade watering pipe with funnel including charcoal, dust, salt, all as shown in electrical plate No 3 of SSR Part-I (2009) complete with necessary earth work in any type of soil, removal to a distance not exceeding 50 mtr, including testing on completion, complete all as specified & directed. Note : (a) The cost of earth work, PCC pit of size shown in electrical plate No.3, funnel, watering pipe, wire mesh, charcoal, dust, common salt, 20mm bore medium grade watering pipe & 15mm bore light grade GI pipe as protection to earth lead wire etc shall be deemed included in the unit rate for earthing. (b) After completion, during testing, if the earth resistance equal or less 2 ohms is not obtained, earthing will be regenerated at no extra cost till the desired earth resistance is obtained.

Energy saving 10W LED bulk head luminaires, IP-65, oval shape, surface mounted with all other accessories prewired and making connections with copper flexible twisted twin cord of appropriate gauge and length,230v, 50Hz including taking down old unserviceable fitting including taking down old unserviceable fittings, complete all as specified & directed. Make. Havells, Cat Part No.RUGBYNEONFT10WLED760SSYMBOPC or equivalent in Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya

Surface & wall mounted, LED tube light fitting, 20W, glare free, smooth light distribution, 230v, box type, epoxy powder coated CRCA sheet housing with reflector cover channel, aesthetic looking end cap and HPF LED driver with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size, complete all as specified & directed. Make. Havells, Cat Part No. ENDURALINEARNEOBS20WLED865SPCWH or equivalent in Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya

Taking down existing ceiling fan of any size and refixing the same after repair of building including provision of three core flexiable copper cord of size 23/0.0076 of required length from ceiling rose or connector to ceiling fan, complete all as specified & directed.

Preparation of old painted surfaces of ceiling fan by scrubbing, cleaning with sand paper/wire brush etc making good surfaces and painting by applying two coats of whitensynthetic enamelled first quality paint over a coat of red oxide zinc chrome primer using spray gun in situ including filling cavities with filler and marking Srl No SM No / MES No with black paint, complete all as specified & directed.

XLPE insulated, armoured heavy duty electric cable (heavy duty) with aluminium conductor, 1100 volts grade, cross-sectional area 10 Sqmm 2 core connected with suitable cable gland and aluminium lugs, laid in trenches or passing through pipes including testing, complete all as specified and directed. (Earth work, brick protection and sand cushioning shall be measured and paid for separately)

Excavation in trenches n.exc 1.5m in width and n.exc 1.5m in depth and getting out in any type of soil for laying pipe line complete all as specified.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete, all as specified.

Removing excavated/surplus material not exceeding . 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified.

Galvanised iron tube 40mm bore light grade (ISI marked) for cable protection to poles/under floor/under roads/alongwith walls complete including sealing of pipe ends with approved sealing compound, complete all as specified and directed.

Sand cushioning to under ground cable, laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete punned to 18cm, complete all as specified and directed. Note:- Punned thickness of sand will be measured and paid.

Brick well burnt locally available sub class 'B' laid over sand cushioning for mechanical cable protection in trenches with width of brick perpendicular to the length of cable, complete all as specified & directed.

M/S VERMA ENTERPRISES

KANWAL KUMAR GUPTA

M/S Darshan Kumar

M/S K K ENTERPRISES