SPECIAL REPAIR TO OTM BUILDING NO 170 AND 70BC ( TOILET AND BATHROOM) AT CHAUBATTIA UNDER GE RANIKHET

Amount

BOQ ( Sch 'A') B/R items Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Material & Labour for coloured/ printed non skid ceramic tiles 7 to 8 mm thick ( square/ rectangular) area of each tiles exc. 0.11 sqm but n.exc. 0.18 sqm as in floors etc set and jointed in neat cement slurry and pointed in white cement with colour pigment over and including 15mm thick bedding layer in CM 1:6 complete all as specified and directed.

Material & Labour for coloured/ printed Glazed ceramic tiles of size 450x300x7mm thick as in vertical surface such as dado/skirtting etc set and jointed in neat cement slurry and pointed in white cement with colour pigment over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) and disposal of unserviceable materials, debris and rubish to a distance not exc 50m as directed by Engr-in-Charge complete all as specified.

Material & Labour for 75mm thick cement concrete 1:3:6 type C-2 (using 40mm graded stone agg) as in plinth protection laid to slope in bays and finishing the surfaces of concrete topping even and smooth without using extra cement cement and exposed edges fair or rounding or chamfering laid in panels complete all as specified and directed.

Material & Labour for cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone agg) as in surface channels and drains including necessary form work complete all as specified and directed.

Extra for forming fair finished drain or channels 30cm inner girth in cement concrete using extra cement including forms, moulds mitred/stopped ends etc all as specified and directed.

Material & Labour Chequred cement concrete tiles30cmx30cmx25mm thick coloured rubber pressed glossy finish of approved pattern & shade as in floors etc set and jointed in neat cement slurry and pointed in white cement with colour pigment over and including 15mm thick bedding layer in CM 1:4 complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) and disposal of unserviceable materials, debris and rubish to a distance not exc 50m as directed by Engr-in-Charge complete all as specified.

Material & Labour for reinforced cement concrete 1:2:4 type B-1(using 20mm graded crushed stone aggregate), as in Slab supported on walls,beams and columns in floors,roof, landing, balconies, chajja etc complete all as specified.

Material & Labour Precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:6 including necessary form work complete all as specified and directed. (reinforcement to be measured separately)

Use and waste of Formwork to chullah hoods, chajja,soffits of suspended slabs such as roof slab, floor slabs landings not exceeding 200mm thick for rough finished surfaces of concrete flat.complete all as specified.

Material & labour mild steel reinforcement TMT bars 10mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Demolition of brick work or stone masonry precast PCC block walling built in cement mortar complete all as specified and directed.

Material & Labour for precast cement concrete block masonry with solid block of cement concrete 1:3:6 type C-1 ( using 20 mm graded stone aggregate) exc 10 cm in width and setting in CM 1:6 complete all as specified and directed.

Material & Labour for brick work with sub class 'B' bricks using old size bricks straight or curved on plan exc 6 mtr mean radius, built in CM 1:4 complete all as specified and directed.

Material & Labour for struck pointing to block in course or ashlar masonry or concrete block walling in Cement mortar1:4 complete all as specified and directed.

Taking down cement or cement lime plaster of any description on brick or PCC blocks or stone wall or concrete surface etc including raking out joints, hacking for keys, scrubbing down with water etc and removing rubbish to a distance n exc 250m complete all as specified and directed.

Material and labour for 15mm thick cement plaster in CM (1:4) on fair faces of brick or concrete surfaces using WPC where ever required as per manufacturerer's instructions and finishing the surface fair and even without using extra cement complete all as specified NOTE -WPC shall be measured and paid separetely.

Material and labour for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces and finishing the surface even and smooth without using extra cement complete all as specified and directed.

Material & Labour for 10 mm thick rendering in CM 1:3 on concrete surfaces as on ceiling and finished even and smooth without using extra cement complete all as specified and directed.

Supply only WPC complete all as specified and directed.

Material & Labour for preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. .

Material & Labour for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed. .

Material & labour for preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer of chalk whiting preparatory to distempering complete all as pecified and directed.

Taking down chowkats or frames n.exc 1.5 Sqm each with shutters (without taking off shutters from the frame) and removed by the contractor complete all as specified and directed.

Taking down chowkats or frames exc 1.5 Sqm but not exc 4 Sqm each with shutters (without taking off shutters from the frame) and removed by the contractor complete all as specified and directed.

Supply & Fixing 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue, pinned at joints and fixed to any position complete all as specified and directed.

Supply & Fixing 35mm thick (batten thickness) IInd class hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged) or of 12mm thick veneered particle board medium density, wood particle board with commercial face veeneers complete all as specified and directed.

Supply & Fixing Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 45 x 70 mm comprising of PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wwod powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Supply & fixing Factory made single extruded WPC (wood polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrwal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N mm2 modulus of elasticity 850 N / mm2 and resistance to spread of flame of Class A catogary with property of being termite/ borer proof, water/ moisture proof and fire retardanat and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In-Charge (Note:- stainless steel butt hinges and necessary SS screws shall be paid separately.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames, glazed with putty or fixed with beads including punching or drilling out old glazing pins/spring clips complete all as specified and directed.

Supply & Fixing 100mm size MS butt hinges, medium weight, cold rolled marked complete all as specified and directed.

Supply & Fixing 75mm size MS butt hinges, medium weight, cold rolled marked complete all as specified and directed.

Supply & Fixing 150mm size Extruded aluminium handle fabricated type anodised complete all as specified and directed.

Supply & Fixing 100mm size Extruded aluminium handle fabricated type anodised complete all as specified and directed.

Supply & Fixing 100mm long Aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

Supply & Fixing 150mm long Aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

Supply & Fixing 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each pane complete all as specified and directed.

Material & Labour for preparation of new or previously untreated wooden surfaces of any description,not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material & Labour for preparation of old painted wooden surfaces of any description,not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing including cleaning for refixing or removal from site complete all as specified and directed.

Material & Labour for 15mm bore GI tubing, medium grade, galvanised with and including all GI fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

All as per Item No 44 here-in-before but fixing only with and including new fittings Note: Old Serviceable GI pipe retrievd from srl item No 42 will be reused.

Material & Labour for 20 mm bore GI tubing, medium grade, galvanised with and including all GI fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

All as per Item No 46 here-in-before but fixing only with and including new fittings Note: Old Serviceable GI pipe retrievd from srl item No 43 will be reused.

Supply & Fixing colour rotational moulded polythene water storage tanks Triple layered (cylindrical vertical with closed top) hoisted and fixed in postion 500 ltrs capacity with and including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram including dismantling PVC/ cement water storage tanks of capacity 500 litres complete all as specified and directed.

Supply & Fixing colour rotational moulded polythene water storage tanks Triple layered (cylindrical vertical with closed top) hoisted and fixed in postion 1000 ltrs capacity with and including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram including dismantling PVC/ cement water storage tanks of capacity 1000 litres complete all as specified and directed.

Supply & Fixing in repairs vitreous china squatting pan Orrissa pattern size 580 x 440 mm white with intregal foot rests, with & including P or S trap including conection to trap and to flush pipe , anti syphonage pipe etc, setting the trap and pan in lime concrete (1 lime, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing (thickness as indicated) and making good to floor complete all as specified and directed

Supplying and fixing in repair white PVC valve less syphonic action type low level flushing cistern of 10 ltrs capacity with inlet ball valve, float valve, handle i including brackets completeall as specified.

Supply and fixing in repair PVC connection 450mm long of 15mm size with PTMT nuts on both sides complete all as specified.

Supply & Fixing vitreous china wash basin, white, flat back, size 550mm x 400mm, (flat back or angle back type) including brackets and including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs complete all as specified and directed.

Supply and fixing in repair pillar tap, push type 15mm dia cast copper alloy with capstan head chromium plated fancy type, screwed down high pressure, with or without letters ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

Supply and fixing in repairs bib tap 15mm dia cast copper alloy, chromium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply & fixing in repairs stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure , with crutch or butterfly handles, screwed both ends for iron pipe of bore 15mm complete all as specified and directed.

Material & Labour for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:4 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and directed.

Supply & Fixing 32mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

Supply and fixing Flush pipe of polyethylene of low or high density 32mm dia for low level cistern complete all as specified and directed.

Supply & Fixing in repairs chromium plated Towel rod 20 mm dia D type 600 mm long of between flange including CP brass screw and wooden/ plastic sheet with fixing arrangement complete all as specified and directed.

Supply and fixing in repairs Brass chromium plated shower rose 80mm size swivel type complete all as specified and directed.

Supply and fixing vitreous china soap dish, white of standard size complete all as specified and directed.

Supply and fixing vitreous china urinal bowl type flat back of size 465x355x265mm white ( minimum), with grating and union for dicharge pipe ( excluding flushing cistern, flush pipe and waste pipe ) including connection to flushing pipe and outgoing pipes complete all as specified and directed.

Supply and Fixing 110 mm bore PVC (SWR) Soil,waste & vent pipe single socketed in any length with rubber ring joints fixed to walls or in floor with and including clamps, nut bolts etc complete all as specified.

Supply and Fixing 75 mm bore PVC (SWR) Soil,waste & vent pipe single socketed in any length with rubber ring joints fixed to walls or in floor with and including clamps, nut bolts etc complete all as specified.

Supply and Fixing PVC (SWR) bends any radius 110 mm bore complete all as specified.

Supply and Fixing PVC (SWR) bends any radius 75 mm bore complete all as specified.

Supply and Fixing 110mm bore PVC (SWR) cowls complete all as specified.

Supply and Fixing in repairs 110mm bore PVC (SWR) branch Piece single ( single Y ) equal or unequal complete all as specified and directed.

Supply and Fixing bore PVC (SWR) gully trap 125/110mm, setting and joinying with solvent cement complete all as specified and directed.

Material and Labour PVC (SWR) floor trap, plain with grating including jointing with solvent cement diametre of outlet 75mm complete all as specified and directed.

Excavation in trenches not exc. 1.50m wide and not exc. 1.50m in depth for foundation for laying cable etc or for manholes cesspits, shafts etc not exc 10 sqm on plan and getting out in hard / dense soil complete all as specified and directed.

Returning, filling in, including spreading , levelling , watering and levelling and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated soil to a distance exc 250m but n.exc 1.5 KM where directed at a level n.exc 1.50m above the starting point complete all as specified and directed.

Dismantling of drain pipes of any type and any description , jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

Material & Labour Salt Glazed stone ware drain pipes Grade 'A' ISI marked laid in trenches and jointed as specifed 150mm internal dia of pipe complete all as specified

Material & Labour for cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in bed to drain pipes of 150mm bore including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

Material & Labour PCC 1:3:6, type C-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

Taking/ stripping out old tar felt over roofs,parapets,chimney stacks etc as laid horizontally or vertically and removing the debries to a distance not exceeding 250 m complete all as specified.

Material and Labour for cutting out cracks to "V" section in existing roofs or terrace, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified.

Material & Labour 15mm thick cement plaster in CM (1:4) using WPC @ 3% by weight of cement as per manufacturerer's instructions and finishing the surface even and smooth (without using extra cement) on concrete surface of roof / parapet, apply and including a coat of bituminous primer confirming to IS:3384-1965 @ 0.30 kg /sqm, apply and including a tack coat of industrial bitumen 85/25 @ 1.20 kg/ sqm, and material & labour for APP based polymeric membrane minimum weight not less than 3.6Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( Wt not less than 150 gms /sqm ) laid by forced application with over lap of minimum 100 mm and the overlap sealed/fused by flame as per manufacturer's instructions. A coat of hot blown bitumen grade 85/25 @ 1.20 kg/ sqm shall be applied on top of APP modified polymeric membrane & finally it will be finished with coat of aluminium paint @ 0.20 litre/ sqm as per manufacturer instruction complete all as specified .

E/M works Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, sockets, lamp holders, brackets, bulk head fittings, tube light fittings etc. and making good disturbed surfaces of walls etc. as per existing finishes by plastering, repairs and white / colour wash etc. complete all as specified and directed.

Supply and fixing of point wiring for one light point / fan point / bell point (independent point), controlled by one, one way switch with 1.50 sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable (FRLS) drawn into and including medium grade PVC conduit concealed (not less than 20 mm dia) all necessary fittings and accessories fixed concealed (including chase cutting in brick/stone masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing suface) and sunk cast iron or pressed steel terminal boxes for mounting fitting like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated bakelite sheet cover fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.50 sqmm size copper conductor cable as in earth wire and connected to common earth dolly complete all as specified (Note:- wiring shall be in done in colour coding as directed by Engoneer in charge )

All as per item No 84 here in before but one socket outlet 5 pin 5 Amp controlled by one, one way switch on same board.

All as per item No 84 here in before but one socket outlet 5 pin 5 Amp controlled by one, one way switch on indipendent board..

All as per item No 84 hereinbefore but wiring with using cable 2.50 sqmm size copper wire (FRLS) and earth wire of PVC insulated (Green colour) 1.50 Sqmm size copper wire for one 6 pin socket outlet, 16 Amp on independent board.

Supply and fixing of switch piano flush type single pole one-way 6 Amp complete all as specified and directed.

Supply and fixing of switch piano flush type single pole one-way 16 Amp complete all as specified and directed.

Supply and fixing of socket outlet 6 Amp, 5 pin , flush type complete all as specified and directed.

Supply and fixing of lamp holder, PVC / polycarbonate type insulated body with back plate suitable for batten / angle fittings complete all as specified and directed.

Supply and fixing of ceiling rose, PVC / polycarbonate isolated body three terminal complete all as specified and directed.

Supply and fixing LED bulb 9 watt complete all as specified and directed.

Supply and fixing of socket outlet two-in-one, 3 pin each suitable for 6 and 16 Amp flush type, complete all as specified and directed.

Supply and fixing high quqlity LED light fittings 1x20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply & Fixing in repair 240 V, 10 KA 'B' curve miniature circiut breaker ( MCB) of single poles carrying capacity 5 to 32 AMP, in the MCB DB complete with connection testing and commissioning including taking existing unserviceable MCB complete all as specified and directed.

Supply & Fixing in rapair 240 V, 10 KA 'B' curve miniature circiut breaker ( MCB) of single pole and Neutral current carrying capacity 32 AMP, in the MCB DB complete with connection testing and commissioning including taking existing unserviceable MCB complete all as specified and directed.

Supply and fixing of sheet metal enclosure for DB’s (Double door type) when MCB’s to be used, single pole and neutral, 8 ways with 200 Amp rated bus bar, 240 volts including blanking plates fixed sunk / flush to the wall or niche complete all as specified and directed.

Supply and fixing of sheet metal enclosure single pole and neutral, with a two pin and earth plug and socket complete with one single ploe MCB 20 amp 240 volt complete all as specified and directed.

Material and labour for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick burried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate), duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C1, GI protection pipe 15mm dia light grade up to 7.5mtr from electrode GI pipe to be fixed with complete all as specified and directed. Note :- (i) Earth lead beyond 7.5 mtr from electrode to earth terminal point/main switch & GI pipe light grade 15mm dia for protection against mechanical damage to lead shall be measured separately. (ii) On testing after completion if desired earth resistance is not obtained, the earthing will be redone at no extra cost.

Material and labour for sand cushioning with a layer of fine sand 8 cm thick before laying the cable and 15 cm after laying the cable in trenches to cover under ground cable complete all as specified and directed. Note :-Punned down thickness of sand shall be considered for measurement)

Material and labour for brick protection to cable using old size class 'B' bricks, laid flat, dry butt jointed, laid lengthwise perpendicular to the axis of cable complete all as specified and directed by Engineer-in-charge.

Supply and fixing / laying of galvanized iron pipe of 25 mm nominal bore light grade for cable protection, fixed to pole/ alongwall/ floor/ under road/ across the drain or nallaha etc with clamps nuts, bolts and washers complete all as specified and directed. Note : The cost of MS clamp, nut, bolt, washer and GI fittings etc shall be included in the item rate.

Supply, laying, jointing and commissioning LT XLPE 1100 volts grade heavy duty cable PVC insulated, stranded aluminium conductor served with inner sheathing of PVC tape, armoured with GI steel or tape and over all PVC sheathing cross sectional area 16 sqmm 2 core laid in trenches, floor through pipes,in duct, on pole and roads etc including making good as per existing complete all as specified and directed. Note : 1. The cost of Al thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for the same. 2. Excavation, earth work, sand cushioning and brick protection will be measured and paid separately under respective items

Supply & Fixing LED street light fitting 60W, 230volt AC outdoor type with high pressure die cast aluminium IP66 roadway luminaire with high power LED as light source and electronic driver including GI bracket light grade 25/32mm with impact and corrosion resistant including thermal management in multiple optics and provn of electric supply to fitting from source by means of PVC Sheathed multi-stranded aluminium conductor cable of suitable size complete including taking down existing old light fitting any type all as specified and directed.

Supply & Fixing in replacement LED bulk head fitting 1x10 watt with PDC aluminium housing and milky diffuser including LED light driver holder, complet eith all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230 Volts, 50 Hz complete all as specified and directed.

Supply and fixing High quility LED lighting fixture mirror type with high ouput diffuser 2 feet 1 x 5 Watt 220V AC, complete with polycarbonate tube, white/ warm white suitable for mirror light internally pre wired of 1.5 Sqmm three core flexible cable complete all as specified & directed.

Supply & Fixing Exhuast fan metal body heavy duty ISI marked , 230 volt, 900 rpm,single phase , 300 mm sweep, with blade, frame and louvers including, cutting, opening through bricks/ stone wall for fixing in openings , grounting of suitable size of nuts & bolts for exhaust fan and making good distrubed surface , connecting flexible cable wire from ceiling rose to exhaust fan complete all as specified and directed .

KUMAON VALLEY CONSTRUCTION

aditya construction