CONSTRUCTION OF AUDITORIUM AT G.I.C. GAIRSAIN, CHAMOLI WITH OTHER APPURTENATN WORK

Amount

Excavation in soil in Hilly Area by manualmechanical means including cutting and trimming of side slopes and disposing of excavated earth with a lift upto 1.5 m and a lead upto 20 m as per drawing and Technical Specification Clause 1603.1 (SOR 8-3-2-A MORD)

Excavation in foundation for retaining & breast walls in all types of soils and rocks including lead, lift and disposal of surplus material as per direction of engineer - in - charge (SOR MISCS. 1-2)

Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work.(Based on PWD specifications) (SOR 2-2)

Random Rubble Stone Masonry laid in 1:6 cement and sand mortar, in breast walls, retaining walls, parapets, scuppers, etc. including supply of all material, labour, T&P and royaltiies etc. (SOR 1-4)

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 P.C.C. grade M 20 Nominal mix (1:2:4) upto 5m height (SOR 12-5-2-1)

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 (SOR 12-9)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. (DSR 2.8.1)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to50m and lift upto 1.5m. (DSR 2.25)

Diluting and injecting chemical emulsion (chlorpyriphos/Lindane E.C 20% with 1% concentration) at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surface of the excavation made for the foundation of the building, soil under floor,apron, back fill material and along all the faces of the walls for PRE CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of building shall be measurd for payment.)

Supplying and filling in plinth with Jamuna sand under floors including, watering, ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) (DSR 4.1.8)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size). (DSR 4.10)

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm bed by dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size). (DSR 5.1.2)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). (DSR 5.2.2)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more (DSR 5.22.6)

Centring and shuttering including strutting,ropping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete. (DSR 5.9.1)

Centring and shuttering for Walls (any thickness) including attached pilasters,butteresses, plinth and string courses etc.

Centring and shuttering including strutting, ropping etc. and removal of form work for suspended floors, roofs, landings, balconies and access platform. (DSR 5.9.3)

Centring and shuttering including strutting,ropping etc. and removal of form for columns, pillars, piers, abutments, posts and struts.(DSR 5.9.6)

Centring and shuttering including strutting,ropping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers.(DSR 5.9.5)

Brick work with common burnt clay F .P .S. (non modular) bricks of class designation 7.5 in foundation and plinth inCement mortar 1:6 (1 cement : 6 coarse sand) (DSR 6.1.2)

Brick work with F. P. S. bricks of class designation 75 in superstructure above plinth level up to floor V level in all shapes and sizes in cement mortar 1:6 (1cement : 6 coarse sand ) (DSR 6.4.2)

Half Brick masonry with F. P. S. bricks of class designation 75 in superstructure above plinth level up to floor V level in in cement mortar 1:4 (1cement : 4 coarse sand ) (DSR 6.13.2)

Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry (with F.P.S. bricks).

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. (35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.)

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing chromium plated brass casement stays (straight peg type) with necessary screws etc. complete : 300 mm weighing not less than 330 gms

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete

Providing and fixing fly proof galvanized M.S wire gauze to windows and clerestory windows using galvanized M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm. With 12 mm mild steel U beading.

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper

Providing and fixing pressed steel door frames confirming to IS: 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge

Profile 'B' (Single Pattam) (DSR 10.14.1.1)

Profile 'C' (Double Pattam) (DSR 10.14.2.1)

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of onlysteel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) (DSR 10.11.1)

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :5.5 mm thick glass panes

Steel work welded in build up section/framed work including cutting, hoisiting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required. In stringers, treads, landings etc. of stair cases including use of chequered plate wherever required, all complete. (DSR 10.25.1)

Steel work welded in build up section/framed work including cutting, hoisiting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required. In gratings,frames, guardbar, ladder, rallings,brackets, gates and similar works. (DSR 10.25.2)

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing including applying a priming coat of approved steel primer. M.S. tube

38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half depth, planed, levelled smooth and finished complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.40mm thick with 20mm nominal size stone aggregate.

Cement plaster skirting (up to 30 cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement. 18 mm thick

12 mm thick cement plaster in 1:4 ( 1 cement and 4 fine sand) mortar including supply of all material , labour and T&P etc. required for proper completion of the work.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand)

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade (New work (two or more coats) over and including priming coat with cement primer)

Finishing walls with textured exterior paint of required shade( New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm.)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

Tile brick masonry work 5 cm thick with tile bricks of class designation 100 in cement mortar 1:3 (1 cement : 3 coarse sand)

Pointing on tile brick work with cement mortar 1:3 (1 cement :3 fine sand) Flush/ Ruled/ Struck or weathered pointing

Providing & fixing pressed clay tile (Mangalore tile) 20 mm nominal thickness and of approved size and as per approved pattern ceiling on steel frame work complete (steel frame work to be paid separately).

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of Engineer-in-Charge all complete. With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non ombustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of Engineer-in-Charge all complete. With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles

Providing and laying brick tiles of class designation 100 over mumty sq.m roofs grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat : With F.P.S. brick tiles

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

Coupler 110 mm

Bend 87.5 degree 110 mm bend

Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including 110 mm

Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture 150 mm diameter S.W, pipe

Constructing masonry chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 (1cement :4 coarse sand ) with C.c 1:2:4 floor over C.C 1:5:10 Finished with a floating coat of neat cement complete .Rectangular shape 600x450mm internal dimensions

Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5kg

Supplying and stacking at site. Over burnt (Jhama) brick aggregate 90 mm to 45 mm

Grading roof for water proofing treatment with cu.m Cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20 mm nominal size)

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly he adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120mm and minimum thickness at khurra as 65 mm

Structrural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting fixing in position and applying a priming coat of approved steel primer all complete:

Structural steel works in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete (wind ties- 40x6 [email protected] kg/mt.)

Providing ridges or hips of width 60 cm over all width plain G.S sheet fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia. G.I limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275gm/sqm.

Painting on G.S sheet with synthetic enamel paint of approved brand and maufacture of required colour to give an even shade :New York (two or more coats) of approved steel primer but excluding a coat of modrant solution.

Supply & installation of precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/- 5% total coated thickness (TCT) thick Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT) thick Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete : Ridges plain (500 - 600mm).

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall

15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work

25 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : Every 5 Mtr.

15 mm nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

20 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

25 mm nominal bore (Horizontal)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Supply and installation of Kirloskar make (1HP) Single phase

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing soil, waste and vent pipes : Sand cast iron S&S pipe as per IS: 1729

100 mm dia

75 mm dia

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :

For 100 mm dia pipe

For 75 mm dia pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete

100 mm diameter pipe

75 mm diameter pipe

Providing and fixing plain bend of required degree wbolts and nuts complete

100 mm diameter pipe

75 mm diameter pipe

Supply and Fixing man hole cover (Rectangular Shape) size 600x450mm

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm

Providing and fixing terminal guard 100 mm Sand cast iron S&S as per IS - 1729

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing collar : Sand cast iron S&S as per IS - 1729

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 200 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :200 mm diameter S.W. pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : nside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, totalweight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as pe standard designWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

FURNISHING WORKS Rain Noise/Heat Isolation: Providing and fixing 1200 GSM non wooven polyester wadding slabs of thickness 50mm wrapped in virgin PVC bags, fixed below the existing roof sheets with GI ceiling sections supports and 24G GI wire netting.

Micro-perforated Gypsum board false ceiling Providing & fixing perforated Gypsum false ceiling , as marked in the drawings, consisting of GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending GI intermediate channels of size 45mm (0.9mm thick with 2 flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angles of width 25mm x 10mm x 0.55mm thick fixed to soffit with GI cleats and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in a direction perpendicular to the intermediate channel at 300mm c/c. Finished in 12.5mm thick micro-perforated gypsum board, 1200mm x 2400mm, with 3mm dia square perforations. The board shall have an overlay of 50mm thick, 1200 GSM polyester wadding, appropriately covered with FGT tissue (in the case of glasswool/ rockwool). The ceiling to be finished with 2 or more coats of mat type plastic emulsion paint after proper jointing & making surface smooth. Approved make of gypsum perforated board: Knauf Danoline/ Absound Overseas/Acoustic India.

Stage suspension Grid: Providing & fixing MS suspension grid system over stage for hanging stage services made of 2 nos 40x40x5mm MS angles welded back to back with 50x12x12mm thk studs as MS spacers sandwiched between the MS angles so as to maintain 12mm gap between MS angles, the welded angles to be placed @ 1200mm c/c in one direction and 40x5mm thick MS Tee @ 600mm c/c in other direction. The MS grid to be suspended from the roof structure by means of MS flat suspender of 50x6mm thick MS flats @ 1200mm c/c in both directions. All MS members to be painted with a coat of red oxide primer & 2 or more coats of black enamel paint.

Woodwool fibril acoustical tiles in stage ceiling: Providing and fixing Fibril wood-wool black acoustical tiles of size 1200x600x20 mm, to be installed existing MS suspension grid. Which will comprise of NRC 0.80. Approved make: Absound Overseas/Herra Design/Acoustic India.

ACOUSTICAL TREATMENT WALL PANELING: Wood grained wooden sound slats paneling for rear wall, side walls, Proscenium & stage front: Providing and fixing Wood melamine finish MDF based panels with lineal perforations to be fixed on walls.The panels shall be with melamine laminate finish of size 2430mm x 128mm x15mm with 4mm slats at 28 mm pitch, Toungue and Groove edges for seamless mounting having density of 750 to 800kg/m3 . The back of the panels are perforated with 10mm diameter circular holes with a nonwoven fabric covering of 0.2mm for providing Sound absorption via the acoustic impedance method.Panel is to be fixed on GI framework as recommended by the manufacturer with screw fixed horizontal / vertical to wall at every 600mm c/c in tongue & groove system on GI framework. The cavity of framework should be inserted with 50mm thick, 1200 GSM polyester wadding. The entire system to be FR grade fire retardant. Approved make:Acoustica One / Absound Overseas/Acoustic India

Fabric wrapped Compressed glass substrate panels paneling on rear & side walls : Providing and fixing Acoustical Wall paneling with square edge panels made of fibre glass substrate 25mm thick with a density of 110-120kg/m3, wrapped on the front side with an acoustical and fire-resistant fabric with an option of colours as per the choice of the person-in-charge, of size1200mmX600mm with an NRC of 0.80 to 0.85 . The panels shall be wrapped with FR grade fabric of approved color & of minimum weigh 340GSM. The panels to be pasted with approved construction adhesives over 9mm thick perforated ply (minimum 20% perforations). The 9mm thick perforated shall be fixed over GI framing consisting of 48x48x0.5mm thick GI Studs wall channels & floor channels @ 600mm c/c with filling of 50mm thick 1200GSM thermally bonded polyester wadding. The insulation to be supported from the back by covering the frame with 19mm mesh GI wire netting. Approved Make : Acoustic India/ Absound Overseas/AMF.

Stage Walls treatment : Providing and fixing 25mm thick fibril panels having density of 400kg/cum, fixed over a framework of GI channels consisting of 48mm GI Stud wall channels & floor channels @ 600mm c/c, filled with 50 mm thick 1200GSM thermally bonded polyester wadding to be held in position with 19mm GI wire netting. Approved Make : Herra Design/ Acoustic India/ Absound Overseas.

Providing & fixing 100x15mm thick Polished wooden skirting of matching shade of wall paneling slats, at the bottom of wall paneling. The skirting shall be fixed over 12mm thick commercial ply to match the level of paneling.

STAGE FURNISHING SUPPLY INSTALLATION TESTING AND COMMISSIONING of FRONT CURTAIN made out of FR Treated approved colour velvet cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangements & motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, 1HP motor (Crompton) 2nos. air breaker contactors (L&T/SIEMENS), 2 nos. micro switches for auto stop, 3nos. push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering. App size 21000x9000. Make of fabric: Banswara, Reliance, Raymonds, Comrade. Make of Track sytem: Canara / New Age / Modern Stage services.

SUPPLY INSTALLATION TESTING AND COMMISSIONING of MIDDLE & REAR CURTAIN made out of heavy glazed cotton fabric with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangements & motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, 1HP motor (Crompton) 2nos. air breaker contactors (L&T/SIEMENS), 2 nos. micro switches for auto stop, 3nos. push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering. size 21000x9000. Make of fabric: Banswara, Reliance, Raymonds, Comrade. Make of Track sytem: Canara / New Age / Modern Stage services.

Providing and fixing WINGS at Stage with heavy glazed cotton fabric of Make: Comrade/ RSWM/Banswar Syntax) fixed complete on 50x 25(1.6 mm thick) MS tube framework @ 1200 (V) x600 (H) c/c backed with 6mm ply & 6mm U foam below the fabric. The rear side of the wing to have 12mm Gypsum board The gypsum board to be given 2 coats of black enamel paint after jointing fisnishing as per the manufacturers recomendations. The side edge to be given a teak wood molding of size 90x15mm duly polished in walnut shade. The wing to be mounted with central pivot mechanism for 180 degree rotational movement at top & bottom. The work shall be executed as per drawings ,specifications & instructions of engineer in charge.

Providing & fixing of the Border frills made out of heavy glazed cotton fabric Make: Comrade/RSWM/Banswara Syntax)) fabric in 1:2 gathers & acessories like cotton dori eyelets of brass complete with 25mm dia medium grade GI pipe painted black suitably hung from the ceiling complete. The work shall be executed as per drawings ,specifications & instructions of engineer in charge.

P/f of the cyclorama for the stage by fixing 35x35x5mm MS angle on the wall with MS angle hold fasts secured to the walls & 40mm dia 14G MS pipe welded to it as per the drgs. Further 40mm dia pipe welded to it at 600 centres verticaly at an angle of 45 deg. & finally welding 40 mm dia pipe horzontally to it. The pipe to be supported away at 200mm centers by MS pipe.(MS framework payable separately) Further welding to it 12mm dia MS hooks welded both (top ,bottom & sides). The cyclorama frame to be supported by MS angle hold fasts of 35x35x5mm on the wall at 1200mm centers. Finally fixing PVC perforated screen, cyclorama cloth as per approved sample & fixing by cotton dori 10mm thick complete.The work shall be executed as per drawings ,specifications & instructions of engineer in charge.

Providing and fixing of 95x22 mm second class Teak wood klin seasoned planks with tongue & groove joints. Teak wood planks to be of minimum length 750mm. The Teak wood planks to be fixed over two staggerd layers of 12 mm thick MR grade ply of approved make fixed to Sal wood frame work of 50 x50 mm and 50x50 mm at 600 mm centre to centre (HxV). The Sal wood shall be kiln seasoned and chemically treated. The framework to be supported on 100 x 100 x 8mm neoprene rubber pads . The framework to be filled with 50 mm thick thermal bonded polyester wadding mikron fiber of 1500 gm/sqm mikron fiber. The stage floor to be PU polished with use of orbital sanders to make floor even before polishing.

Providing and fixing first class teak wood lipping/moulded beading or taj beading of size 70x50mm fixed with wooden adhesive of approved quality and screws/nail on external edges of stage .The work shall be executed as per drawings ,specifications & instructions of engineer in charge.

SOUND REDUCING DOORS Entry/exit doors for the auditorium 77mm thick, acoustic doors consisting of fire resistant materials & peripheral seals all around . The door to be laminated with 1mm thick laminate. The Door shutter frames to be of klin dried chemically treated teak wood. The door shutter frame to be lapped with 12mm commercial ply duly treated for fire retardance. Make : Global Fire/ Navair/ Absound Overseas.

Chowkhats for the doors in second class teak wood of size 110x 90mm duly fire treated.

Providing and fixing Hinges (Steel with bal bearings ) of size 125 X 32mm fixed with steel drive all screws of 35mm. Make: Doors, Ozone, Dorma

Providing and fixing heavy duty door closure app. 100Kg capacity with all necessary parts. Make: Becker/Dorma/Doorvin/Ozone

Providing and fixing heavy duty SS door handles of 450mm high, made of SS304 grade with all necessary parts. Make: Becker/Dorma/Doorvin/Ozone

Providing and fixing heavy duty SS tower bolts of 450mm high with all necessary parts. Make: Becker/Dorma/Doorvin/Ozone

AUDITORIUM CHAIRS & CARPET FLOORING Providing and fixing of tip up & back push type auditorium chair of size 550mm c/c upholstered with Fire Retardant fabric (FR Fabric conforming to BS EN 1021&1) . The chair to have MS tubular framework welded together with continous arc welding. The chair shall have powder coating of 65microns on all of the MS tubular framework . The seat shall have Polyurethane foam of density 50+3 KG/Cum & Back to have density of 50+3 Kg/CuM. The height of the back to be 950-1000mm from the ground to top of back & for Seat to be 400-450mm from the ground . The rear of back shell & bottom of seat shell to be Polypropylene plastic in black colour Polypropylene plastic cover. The wooden armrest to be of 80mm & 400mm length with melamie polished in black colour . The armrest between two chairs in a row to be shared & at the both ends to be individual. Including cost of expnasion fastners as required of reputed make. The bench shall be fabricated as per drawings ,specifications & instructions of engineer in charge. Approved Make: Wipro / Featherlite /Absound.

Providing and fixing machine tuffed loop pile high low scroll nylon carpet effective pile height 6mm, total pile weight not less than 650 gm/sqm. secondary backing action back 55 gms/sqm. In rolls of 3.66 mtr. width as per size, shade, design and direction of Engineer-in-charge and as per manufacturer's specifications. The sample may be approved by the Engineer-in-charge before start of the work. The surface area will be measured for payment. The carpet to be bakced with 6mm thick PU underlay. Approved make: Absound floor, Heritage, CCIL.

STAGE LIGHTING SYSTEM SUPPLY INSTALLATION TESTING AND COMMISSIONING of 1000W Halogen Planoconvex spot light complete with1000 W Halogen Bipin T-11 lamp, spherical anodised reflector, imported socket, 150mm dia planoconvex lens, bottom sliding knob, yoke, colour frame & suitable clamp, safety chain complete as required. Make : Canara / Effectron / New Age / MSS

SUPPLY INSTALLATION TESTING AND COMMISSIONING of 1000W Halogen Fresnel light consisting of 1000W Halogen Bipin T-11 lamp, 150mm dia imported fresenel lens, Imported socket, bottom sliding knob, yoke, colour frame & suitable clamp safety chain complete as required. Make : Canara / Effectron / New Age / MSS

"SUPPLY INSTALLATION TESTING AND COMMISSIONING of 1000 W Halogen profile light consisting of 2 nos. 150mm dia PC lenses, imported socket, ellipsoidal anodised alluminium reflector, 1000W halogen BipinT-11 lamp, yoke colour frame & suitable clamp safety chain complete as required. Make : Canara / Effectron / New Age / MSS

SUPPLY INSTALLATION TESTING AND COMMISSIONING of 1000W, 240 Volt, PAR Sealed Beam Light 16 SWG aluminium duly painted powder quoted paint , lamp 1000watt 240V OSRAM/Philips lamp CP-61/62,Ceremic type base GX 16 D mat black color, yoke & clamp safety chain complete as required. Make : Canara / Effectron / New Age / MSS

SUPPLY INSTALLATION TESTING AND COMMISSIONING of 500W Halogen Cyclorama Flood Light with 500W Halogen tube. Alluminium anodised reflector, 2 nos compressible recessed single contact holders, colour frame & suitable clamp safety chain complete as required. Make : Canara / Effectron / New Age / MSS

SUPPLY INSTALLATION TESTING AND COMMISSIONING OF 1000 W Halogen light with mash & barndoor consisting of 2nos. single contact compressible holders, yoke, 1000W halogen tube & suitable clamp safety chain complete as required. Make : Canara / Effectron / New Age / MSS

SUPPLY INSTALLATION TESTING AND COMMISSIONING of M.S. Pipe Ladders to be provided on sides of the Stage to be fixed on the existing GI pipe or top grid. Made of 50mm x 25mm MS pipe complete as required size 1800x600. CUSTOM BUILT

SUPPLY INSTALLATION TESTING AND COMMISSIONING of Motorized Hoisting System consisting of Motorised winch with 1.5hp, single phase Motor,Gear Box 30 : 1 ratio , 3 # hydrolic thryster break for extra potection , 5 or 6 Pulley with 4 mm rope wire for uplift the light bar, 6 mm rope wire for main drum for uplifiting the complete bar with cable basket fix on it. Including control panel to control all the set bars operation complete with all accessories. The set bar to have min 500kg load bearing capacity for Scenery Sets, Light Bars, Frill Bars with Pullies, Hamp Rope, Clamp, Weight, etc. Recomended makes: Canara / New Age/ Modern Stage Service

SUPPLY INSTALLATION TESTING AND COMMISSIONING of Light Point Wiring from Patch Panel to be provided near stage to various stage light fixtures with FRLS 2.5 Sq.mm 3 Core PVC Insulated and PVC Sheathed Cable including Cable Tray of suitable size for laying these wires on the tray including 16AMP MULTISOCKET AND PvC cable tray mountable box complete with accessories as required.FRLS 3 core 2.5 sqmm wires. Make of wires : Polycab / Finolex / Skytone / Havells. Make of Switch Sockets & box : Nothwest / Anchor / Schneider / MK

SOUND REINFORCEMENT SYSTEM Wireless VHF microphone system, handheld transmitter and receiver inclusive, 3 frequency band variants available (174-184 MHz, 194-204 MHz, 213-223 MHz), with accessories.Make: Beyerdynamic/Shure/Sennhelser.

Wireless VHF Lapel microphone system, 3 frequency band variants available (174-184 MHz, 194-204 MHz, 213-223 MHz), with accessories.Make:Beyerdynamic/Shure/Sennhelser .

UHF Wireless Headworn Microphone System, Receiver: 3 frequency band variants available (174-184 MHz, 194-204 MHz, 213-223 MHz), with accessories.Make:Beyerdynamic/Shure/Sennhelser With the prior approval of EIC.

Dynamic Vocal/Instrumental Microphone, Polar pattern: Supercardioid, Frequency response: 30 - 18,000 Hz, Impedance 600 Ω, Load impedance 2K Ω, On/Off switch, 3-pin XLR male connection, etc. all complete. Make: Beyerdynamic / Shure / Sennheiser.

Gooseneck Microphone, Transducer type: Electret condenser, Polar pattern: Cardioid, Frequency response: 50 - 19,000 Hz, Open circuit voltage:17 mV/Pa, Nominal impedance: < 200 Ω, Load impedance: Make:Beyerdynamic/Shure/Sennhelser/Audiotechnica.

Active DI Boxes for electronic instruments with +48 V phantom Power,0 to 20dB Switchable Attenuation,Earth Lift Switch. Make: Klark Teknik - DN100/BSS AR133.

Floor mount box for microphone connectivity (2 x XLR in) . Custom made.

Floor mount box for Monitor connectivity (1 x XLR out). Custom made.

24-Input 4/2-Bus Mixer with 10 Microphone Inputs, 4 stereo inputs,8 Compressors, EQs, Multi-FX Processor with LCD display, Wireless Option,built-in stereo USB/Audio Interface. Make: Music group, Harman, Yamaha.

15-Band Stereo Graphic Equalizer with FBQ Feedback Detection System,dedicated mono subwoofer output, ultra-low noise operational amplifiers. Make: Music group, Harman / Bosh.

24-Bit, 96 kHz, 2 input and 6 ouputs Loudspeaker Management processor. Make: Music Group, Harman, Bosch.

FOH : 400-Watt, 3-Way passive Loudspeaker System with 15" LF, 6" MF and 1.35" HF Transducers or better,8 Ω impedence. Make Music Group/Harman / Bosch.

Ceiling hanging arrangement for FOH. Custom made..

Front Fills : Ultra-Compact 2-Way Loudspeaker System with 6" LF and 1" HF Transducers or better, 100 Watt RMS power,8 Ω impedence. Make Music Group/Harman / Bosch.

Stage Monitor : Active 1000-Watt 2-Way 12" PA Speaker System with Wireless Option and Integrated Mixer, with accessories. Make Music Group/Harman / Bosch.

Class D Stereo Power Amplifier with 2 x 850 Watts into 4 Ohms;2 x 440 Watts into 8 Ohms; 2000 Watts into 4 Ohms (bridge mode);1200 Watts into 8 Ohms (bridge mode) output power, Distortion <0.2%, with accessories Make: Music Group/Harman / Bosch/QSC.

Class D Stereo Power Amplifier with 2 x 300 Watts into 4 Ohms;2 x 150 Watts into 8 Ohms; 800 Watts into 4 Ohms (bridge mode); with accessories. Make: Music Group/Harman / Bosch/QSC.

WIRING SYSTEM : Speaker Lines for speaker - High grade, professional, low-noise, 2-Core High conductivity PVC insulated in PVC jacket, shielded, Copper Cable with di-electric insulator including PVC conduits.

Microphone Lines for microphones -High grade, professional, low-noise, 12-Core snake cables, High conductivity PVC insulated in PVC jacket,shielded, copper cable with di-electric insulator with XLR male/female connectors of following lengths including PVC conduits.

System Rack 35 RU for housing equipments.

System interconnection cables for system in control room.

Designing, Installation, Testing, Commissioning, Programming & Training Charges.

VIDEO PROJECTION SYSTEM VIDEO EQUIPMENTS 7000 lumens WXGA (1280 x 800) 3 LCD projector with 3000 hours lamp life, HDMI, HD15, Display Port, Built in LAN port, Powered optical vertical and horizontal Axis shift complete with standard lens. Make: Panasonic/Christie/Vivitek.

Fixed ceiling mount kit for the projector. Custom made.

2x1 HDMI/VGA over HDBaseT Auto-Switching 2-Gang In-Wall Transmitter. Make: Wyrestorm/Kramer/Extron.

HDMI twisted pair receiiver module. Make: Wyrestorm, Kramer, Extron.

4x1 HDMI Switcher with upto 2.25Gbps bandwidth per graphic channel, HDCP Compliant complete with wireless remote control. Make: Syrestorm, Kramer, Extron.

HDMI Audio De–Embedder. Make: Wyrestorm, Kramer, Extron.

HDMI twisted pair extender set with Bi-directional IR. Make wyrestorm, Kramer, Extron.

16 U Equipment Rack . Custom made.

Various cables ,Connectors & accessories. Make Krystal, Belden, Canare, Neutrik, Amphenol, Switchcraft, D-Link

Installation, Testing & Commissioning of complete system: Make : Integrator

Supply and installing MS. Pipe "C" Class, IS 1239 standard including cutting, welding etc. Providing all required accessories like flanges, bends tees, reducers, supporting with GI. clamps etc. including painting with one coat of primer and two coat of red Synthetic enamel paint of aoopproved make &shades.(Pipe of TATA / JINDAL/SURYA) 100 mm dia

Supply & Installation C.I. Butterfly valve of PN1.0 Rating , confirming to IS standard , complete with Flanges, gasket and nuts , bolts , etc .CASTELE/KARTAR/SANT 100 mm dia

Providing and fixing single headed landing valve (hydrant) of 63 mm dia made of SS Hydrant valve ISI. Mark is completed with erection and necessary fitting etc. Confirming to IS: 903. OMEX /NEW AGE/ MINIMAX/GETECH

Providing and fixing impact, abrasion and weather resistant rubberized fabric lined (RRL) hose pipe confirming to IS:636-1979 (TYPE A) of 63 mm dia and 15 meter length with SS instantaneous male and female couplings confirming to IS:903:1975. OMEX /NEW AGE/ MINIMAX/GETECH

First Aid Hose Reel Complete With hose Drum and 30 m hose for Internal fire Fighting .Omex new Age /Minimax getex

Providing and fixing doors for Internal hose cabinet made of ms / al angle with glass doors suitablepable of accommodating landing valve, hose pipes, fittings & accessories. OMEX/SB/NEWAGE

supplying and fixing approved make 25mm dia. Automatic air release valve

Providing and fixing of air vessel. 200 MM DIA X 1200 M

Pressure Gauge. DANFOSS make

Suppling and fixing 9 kg . Sand bucked along with bracket grouted in walls with necessary hardware. The bracket will be stove enamel painted inside with white colour and red comour outside. Also FIRE, letters to painted in white enamel paint on outside surfase.

Fire buckets round bottom type enamel painted, white inside & Red out side and along with stand fabricated from MS angle to accommodate 4 buckets

Providing & Fixing pump near Terrace tank type-Monobloc MB G1.52 (1.5 HP) Pipe Size 40x32 (1.1 Kw) 3000 RPM (SYN) Head Range 15-28.5) discharge (175-50 LPM

Providing & Fixing Pumps to fill Fire tank 2 HP Monobloc Pump

Providing & Fixing Nozzle For Hose Pipe

Providing & fixing CO2 Type Fire Extinguisher complete with Refill, ISI marked Tested & Approved. capacity 4.5 kg

INTERNAL ELECTRIFICATION WORK Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2x2.5 sq. mm + 1x2.5 sq.mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire for power DB

4x10 sq. mm + 2x6 sq.mm earth wire

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cuttting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 amps switch

3 pin 5/6 amp socket outlet

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing 3 pin, 5 amp. ceilling rose on the existing junction box/ wooden block including connection etc. as required

Supplying and flxing brass batten/angle holder including connection etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq, mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan upto 450 mm sweep in the existingopening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.

Extra for fixing louvers/shutters complete with frame for a exhaust fan of all sizes.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 way (4 + 18), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissoning etc. as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc.with charcoal/ coke and salt as required..

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supply of AC 230/250 volts, 50 HZ energy efficient ceiling fan with standard down rod, blades, 3 nos. caps Model-ES 50 (1200 mm Sweep) etc. complete in all aspects as per direction of Engineer in Charge

1200 mm sweep

Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete . Model- Ventil Air - DS (Make : Havells) 300 mm sweep 900 rpm ,complete in all aspects as per direction of Engineer in Charge.

300 mm sweep 900 rpm

Supply & fixing of heavy duty wall mounted fan- 400 mm dia Model - D’zire complete in all aspects etc. as per direction of Engineer in Charge

SUPPLY OF LED Glass Bulb B22, 15 W ,6000k /4000k/3000K ,230/250 Volt,50 HZ ETC, complete in all aspects as per direction of Engineer in Charge.

Supply and fixing of LED Tube light 1200mm 20W 865 T8 IP20 ,Lumen Output-1600 , 3000, 4000, 6500K ceiling mounted LED batten (E-LITE LED TRIYCA) , extruded aluminium heat sink provided for efficient heat deissipation 7& integrated electronic driver. ( 1x20 W LED Double 6500K) complet in all aspects as per direction of Engineer in charge.

Supply & fixing of LED Mirror Light -Providing & Installation of Linear & compact 9W ,4000k mirror light with decorative grey end caps, polycarbonate body and ribbed opal diffuser.(for recess in wall ) connecting wire etc.of standard make (Havell's) as per direction of Engineer in Charge..

Supply & fixing of LED Down Light (15W) -Providing & Installation of Recess mounted pressure die-cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and separate replaceable electronic driver compatible for Analog/DALI Dimmingconnecting wire etc.of standard make (Havell's) as per direction of Engineer in Charge.

Supply & fixing of Ceiling Light PLUTO NEO PANEL Environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling (600X600mm) with electronic driver & high Brightness SMD LED's. Lamp Type 34 Watt LED 4000 ,6500 K . High efficiency diffuser IP 20 complete in all aspects like Ballast , housing connecting wire etc. as per direction of Engineer in Charge.

Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes.

3.5c x 50 sq. mm cable

Supply & fixing of main panel with 1 no. incomer of 100 amp.TPN MCCB (25 KA)& outgoings of 02 no. 40 amp. FP MCB 25 KA) & 02 no. outgong of 15 amp. FP MCB with suitable busbar, change over switch, ammeter, voltmeter , indicating lamps etc. complete in all respect. Note:- 1. No cartage shall be paid extra. The work will be executed as per agreement of shedule G and as per direction of Engineer-in-charge if the contractor executes any work beyond the quantity mentioned in schedule 'G' without the written order of the Engineer in such case these extra quantities shall be accepted by the department. 2. Royality for sand & stone is deemed including in the rate and the contractor shall pay for them himself and certify to that effect.