Supply, Installation, Erection, Commissioning and Testing of Goods cum Passenger Lift having capacity of 1500 Kg at Boiler Plant.

Sl. No. ITEM UNIT GUARANTEED PARTICULARS BY BIDDER

2 Type – Standards IS 17900 (vendor to confirm)

3 Capacity -1500 Kg (vendor to confirm)

4 Rated speed 0.7 M/Sec (vendor to confirm)

5 Contract speed M/sec

6 Car dimensions (L X B X H) mm

7 Overall weight Kg.

9 No. of Landings and Locations as per clause no 1.1.2(vendor to confirm)

10 Lift control type

12 Levelling device

13 Type of car and landing doors

14 Size of doors mm x mm

15 Door Operator

16 Vision panel in doors

17 Operating devices in car

18 Operating devices in landings

19 Indicating devices in car

20 Indicating devices in landings

21 Details of car lighting

22 Details of car ventilation

23 Details of Painting

24 Pit height from bottom landing mm

25 Clearance between top landing and Machine Room mm

26 Machine Room Dimensions (L X B X H) mm

27.2 Enclosure and Ventilation

27.3 Rated voltage V

27.4 Winding insulation class

27.6 Torque/speed characteristics enclosed Yes/no

27.7 Temperature rise at full load °C

28.3 Number of Ropes Nos.

28.4 Diameter of Ropes mm

28.5 No. and diameter of strands Nos,mm

28.6 Cross sectional area mm2

28.7 Outside diameter mm

28.8 Ultimate strength Kg

28.9 Working stress Kg/cm2

29 Enclosure for electrical equipment shall be IP-65 (vendor to confirm)

30 Sheaves and Pulleys

30.1 Material for construction

30.2 Dia and grooves Mm, Nos.

31.1 Type / Make

31.3 Rated Speed RPM

31.4 Tripping Speed % of RPM

31.5 Weigh loaded / Spring loaded

31.6 Setting range

31.7 Factory set value

31.8 Safety switch type

31.9 Provision of actual speed measurement

32 Type of brake

33 Hand cranking device

38 Counterweight Kg.

38.1 Location of counter weight

39 Control & Power system

39.2 Location: Lift Control Room at G Floor(vendor to confirm)

39.3 Enclosure: Double front indoor type (vendor to confirm)

39.4 Enclosure thickness mm

39.5 Degree of ingress protection as per IS 13947: IP-65, Dust proof, Weather proof & vermin proof Yes/no

39.6 Type: Fixed type, free standing floor mounting with hinge doors Yes/no

39.7 Material of construction: The enclosure shall be fabricated from 14 SWG (2.0 mm) MS CRCA sheet steel. Yes/no

39.8 Hardware: All hardware shall be of Stainless Steel grade SS-304. Yes/no

39.1 Gasket: Neoprene rubber gasket shall be used to achieve water and dust proofing for inside door Yes/no

39.11 Earthing: AL Earth bus of suitable size to be considered. 02sets of Nut-bolts with Plain & spring washers not less than M8 X 40 mm of SS-304 shall be provided with the panels for external and internal earthing. Yes/no

39.12 Cable Entry: Necessary knockouts shall be made for entry of cables as per requirement at panel bottom side. Yes/no

39.13 Power & control panel: The overall size of the enclosure shall not be less than 750 (W)X 1500(H) X 500(D) mm. Yes/no

39.14 ARD Panel enclosure shall not be less than 600 (W)X 1000(H) X 300(D) mm. Yes/no

39.15 The control panel & its Microprocessor based controller shall be suitable for 50 degree ambient temperature. Yes/no

39.16 Min. clearance between: Phase to phase: 25 mm Yes/no

39.17 Min. clearance between: /Phase to earth :19 mm Yes/no

39.18 All components installed in control panel shall be suitable for 50 degree ambient temperature. Yes/no

39.19 Selection of switch, MCCB, MPCB, MCB, contactor & relays shall be as per Type-2 co-ordination. Yes/no

39.2 Make of all components like limit switches, Contactor, Push buttons, , MCCB, MPCB, MCB, Relays, Control transformer, Aux. relays, meters, Lamps, etc Yes/no

39.21 Primer: Two coats of epoxy based primer & stoved after each coat. Yes/no

39.22 Final paint: Two coats of epoxy paint (acid proof). Yes/no

39.23 RAL 7032 (Siemens-Grey) paint shade with paint thickness 80 microns. Yes/no

39.24 Panel all drawings to be submitted for review and approval of Purchaser. Yes/no

40 AC VFD Drive

40.3 Rating: kW

40.4 Rating of VFD shall be one size higher than Motor Rating. Yes/no

40.5 Other details if any.

41 Micro Processor Based control system

41.1 Latest Microprocessor based control system to be provided. Contactor logic system will not be accepted. Yes/no

41.5 Other details if any.

41.6 Vendor to provide and give details of suitable diagnostic intelligence fault/error diagnostic feature to save upon trouble shooting time. Yes/no

42 Control Cables

42.3 Cores Nos.

42.5 No. of cables

42.6 No. of cable groups

43 Power Cables

43.3 Cores Nos.

43.5 No. of cables

43.6 No. of cable groups

44 Brake Details

44.1 Dust proof, weather proof IP-65 Yes/no

44.6 Other details if any

45 Gear Box Details

45.5 Type of lubricating oil

45.6 Other details if any

46 Drum Details

46.5 Other details if any

47 Coupling Details

47.5 Other details if any

48 Governor Rope

48.4 Number of ropes Nos.

48.5 Dimensions mm

48.6 Other details if any

49.1 Make Yes/no

49.2 Mounting : B3 Yes/no

49.3 Frame Size:

49.4 Design Ambient temp : 50 deg C Yes/no

49.5 Type : Squirrel cage Induction motor Yes/no

49.6 Inverter grade motor suitable for operation by VVVF controller. Yes/no

49.7 The motors should comply with Standards (latest version) IS: 325, IEC: 60034. Yes/no

49.8 Starting of machine / Method of starting : On load / VFD Starting

49.9 Class of protection: IP 65 Yes/no

49.1 Voltage : 415 V,AC +/- 10% Yes/no

49.11 Frequency : 50 Hz + 3% - 6% Yes/no

49.12 Fault level : 35 MVA Yes/no

49.13 Phase : 3 Yes/no

49.14 Enclosure type : TEFC Cast Iron body Yes/no

49.15 Duty cycle : S4 (Intermittent periodic duty with starting) Yes/no

49.16 Insulation : Class H insulation but temp rise limited to class F Yes/no

49.17 Duty : Suitable for Lift Application Yes/no

49.18 CDF (Cyclic Duty Factor) : 40% Yes/no

49.19 Start/Hr : 150 Yes/no

49.2 No. of terminals : 6 Yes/no

49.21 Specific requirement: Motor should be with extended shaft on NDE side for hand cranking operation of lift, during Emergency operation. Yes/no

49.22 Motor should be capable to run with electromagnetic braking. Yes/no

49.23 All hardware of motor shall be of SS-304. Yes/no

49.24 Motor datasheet to be submitted for review and approval of Purchaser. Yes/no

50 Other equipment/components

50.1 All protective, safety & limit switches, door interlock shall be dust & weather proof IP66 with SS-304 hardware. Yes/no

50.2 Hall/Landing push buttons stations shall be IP65 SS-304, with SS-304 hardware. PBs with illuminated call registration light for all landing doors. Yes/no

50.3 Panel inside the car shall be IP65 SS-304, with SS-304 hardware. PBs with illuminated call registration light for car. Yes/no

50.4 Car inspection box at top of the car shall be IP65 SS-304, with SS-304 hardware. Yes/no

50.5 Over speed Governor Safety switches shall be IP65, with SS-304 hardware. Yes/no

50.6 Car door switch shall be IP65, with SS-304 hardware. Yes/no

50.7 Junction boxes for wiring & main/ midway JB shall be IP65, SS-304 with SS-304 hardware with double door arrangement. Yes/no

50.8 All other junction boxes for wiring shall be IP65, SS-304 with SS-304 hardware. Yes/no

50.9 All steel items of hoist way shall be Epoxy coating, Anti-corrosive paint to withstand against corrosive atmosphere. Yes/no

51 Earthing System

51.1 GNFC will provide main earth connection to earth bus located in machine room and vendor shall carry out earthing of various electrical equipments located inside the machine room. Also the vendor has to make suitable arrangement for effective earthing of the electrical equipments mounted on the top of car / inside the car. Yes/no

52 Tools and Tackles

52.1 A tool box containing special tools required if any, torque wrench, cranking Handle, set of spanners, screw drivers etc. shall be supplied along with the LIFT. Yes/no

53 Car Inside Lighting

53.1 The car lighting supply shall be independent of the power supply mains. Yes/no

53.2 Light should remain ON when lift is available for use. Yes/no

53.4 Type: LED type Yes/no

53.6 Number of Fixtures: Nos.

54 Other Lighting

54.1 Supply and installation Dust proof, weather proof, 240 V AC, IP 65, LED fixture with industrial enclosure on car top for maintenance activities. Wiring shall be in vendor’ scope. Yes/no

54.2 Supply and installation Lift well and machine room lighting shall be in Vendor Scope. (Vendor should consider 2 Nos. lights diagonally at every interval of 4 mtr. height in lift well). Wiring shall be in vendor’ scope. Yes/no

54.4 Rating: (Min.45W) W

54.5 IP Rating: (Min IP-65) Yes/no

55 Industrial Power Supply Sockets.

55.1 Supply and installation Dust proof, Weather proof IP-65 240V, 1ph Industrial interlocked Power supply Switch Socket with 2P RCBO at Car top, Machine room, Control panel room and in lift well for maintenance activities. Yes/no

56 Ventilation Fan inside Car

56.1 Ventilation fans with switch shall be provided inside the Car. Fan shall be auto cut OFF when car stops. Yes/no

57 Communication Facility inside Car

57.1 Vertically mounted industrial Intercom phone shall be provided by vendor in lift car, machine room as well as at Control room/ Substation for communication. Wiring shall be in vendor’ scope. Yes/no

57.2 Vertically mounted PA System equivalent to hook up with existing PA System of plant. Yes/no

57.3 Announcement system for Floor, Overload warning announcement facility etc. shall be provided. Yes/no

58 Limit switch & safety switch

58.4 Enclosure material

58.5 Ingress protection: (Min. IP-65)

59.1 Mandatory spares for 05 years of trouble free operation and maintenance of Lifts will be considered for supplied by Bidder as per ANNEXURE-C Yes/no

59.2 Guarantee Period

59.3 The equipment shall be guaranteed for the specified duty, for repair / replacement, free of cost to OWNER of any defect, fault or deficiency in vendors design, engineering, material, workmanship, construction and manufacture for a period of 18 months from the beginning of commissioning of work or 36 months from delivery at site whichever is later, unless otherwise stated. Yes/no

60 Comprehensive AMC confirmation after completion of Guarantee Period

60.1 5 years of Comprehensive AMC confirmation after completion of Guarantee Period to be consider by vendor. Yes/no

This CAMC includes the following scope of services:

1] Monthly Routine Services and Breakdown Services

2] Assistance during Yearly Load Test, Licence Renewal, Six Monthly 3rd Party Inspection.

3] Repairing / Replacement of consumable items as per ANNEXURE-D. Components will be furnished by the Vendor on exchange basis

Same can be awarded at yearly basis to successful bidder if GNFC requires and will be as per the clauses of mini GCC of GNFC only.

61 Delivery period and execution period

61.1 Supply Material Delivery period

61.2 Execution period [Erection, commissioning, testing period]