Special Repair for upgradation of Sub Health Centre (SHC) into HWC at Kalarheri (Under BOH P.H.C.) in Ambala District

Amount

Earth work in excavation in foundations, trenches etc. in all kinds of soil, not exceeding 2 meters depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry in 15 cm layers with compaction, including disposal of all surplus soil as directed within a lead of 30 Mtrs. (HSR 6.6)

Dismantling cement conglomerate /terrazzo floor 25 mm to 50 mm thick without concrete base. (HSR 8.26)

Scraping (a) White wash and colour wash. (HSR 8.32 (a))

Scraping (c) Cement plaster. (HSR 8.32 (c))

Cement concrete 1 : 8 : 16 with brick ballast 40 mm Nominal size in foundation and plinth.(HSR 10.26)

Cement concrete 1 : 4 : 8 with stone aggregate 40 mm Nominal size in foundation and plinth. (HSR 10.39)

Damp proof course 25 mm thick of cement concrete 1:2:4 using stone aggregate 20 mm nominal size with 2 coats of bitumen 20/30 penetration, at 1.65 kg per sqm laid hot and sanded. (HSR 10.115 (-) Note.

Providing and laying 80 mm thick ISI Marked interlocking paver blocks conforming to is 15658 : 2006/ IRC SP 63-2004 of all shapes and colours in design mix cement M-40 over a bed of 30 mm thick fine sand complete in all respect. (HSR 10.159) (Note :- Reputed make Paver Block Only ISI marked will be used as approved by Engineer – in – Charge).

First class brick work laid in cement mortar 1:4 in foundation and plinth.(HSR 11.4)

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level. (HSR 11.9)

Tile terracing with one layer of tiles, 22.86 cm X 11.43 cm X 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1:3 and top surface to be left clean. (HSR 13.14)

Cement concrete 1:2:4 gola 10 cm X 10 cm quardrant along junction of roof with parapet wall finished smooth, where specially specified. (HSR 13.64)

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. (HSR 13.89). (a) 100 mm dia PVC pipe 6 kg. pressure.

Providing and fixing PVC Bend ISI Mark. (Note:- Reputed make PVC Bend such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. (HSR 13.90). (a) 100 mm dia PVC Bend.

Providing & Fixing Vitrified Tiles 600 x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand morter 1.3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like:RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL (Double charged tiles shall be used as approved by Engineer in charge. (NS). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Glazed tiles 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. (HSR 14.92(b)). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

12 mm thick cement plaster 1:4 (HSR 15.5)

12 mm thick cement plaster 1:6 (HSR 15.7)

15 mm thick cement plaster 1:6 on the rough side of single of half brick wall (HSR 15.12)

Cement pointing 1:2 deep variety on brick and Tile work (HSR 15.60)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.2).

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3).

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surface. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.25)

White washing three coats. (HSR 16.48)

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work. (HSR 16.60)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.79 (b)). 1st Quality

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81).

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12).

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT WITH NON-CONCEALED ‘P’ OR ‘S’ TRAP with or without vent and all other necessary Fittings as fully described in item no. 30.3 above. (HSR 30.4) (i) White

EXTRA OVER item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY C.I. LOW LEVEL VITREOUS CHINAWARE CISTERN complete with flush bend all other necessary Fittings instead of C.I high level cistern complete with fittings. (i) White. (HSR 30.12 (i)).

EXTRA OVER item nos. 30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow Black or white plaster seat and lid.(i) White plastic seat (Solid). (HSR 30.13 (i)).

Providing & Fixing in position best Indian make (ordinary) lavatory suites consisting of:- (v) Size 560 mm x 450 mm with one no. tap. (HSR 30.41(v)).

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge) (HSR 30.75) (a) Bib cock long body (HSR 30.75) (a))

Providing & fixing in position C.P. brass stop cock (as approved by the engineer-in-charge). (a) 15 mm Stop cock. (ii) Concealed stop cock with flange. (HSR 30.76 (a) (ii)).

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE FLEXIBLE TUBE CONNECTION (HSR 30.82) (b) C.P Brass (iii) 15 mm x 450 mm

Providing and fixing in position automatic brass ball valves in tanks. (b) With Plastic Ball (iii) 25 mm internal diameter. (HSR 30.110 (b) (iii)).

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flages for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. (HSR 30.119). 1000 Ltrs. Capacity Water Tank

Supply and Fixing of G.I. Pipe complete in all respects to the satisfaction to the Engineer-in-Charge. . (NS)

NOTE:- 1. IN CASE OF ANY DIFFERENCE IN THE UNIT & NOMENCLATURE OF ANY OF THE HSR ITEMS OF CIVIL, P.H. WORK DEPICTED IN THIS DNIT AND THAT GIVEN IN HSR, THE UNIT AND NOMENCLATURE GIVEN IN HSR SHALL BE APPLICABLE. 2. ONLY REPUTED MAKE MATERIAL WILL BE USED (MAKE/BRAND EXHIBITED IN HSR AND EXHIBITED IN APPROVED STANDARD DOCUMENT) AS APPROVED BY ENGINEER-IN-CHARGE, WHILE EXECUTING VARIOUS ITEMS/WORKS AT SITE.

MAHINDER PAL