ADDITION ALTERATION AND SPECIAL REPAIR OF WATER PROOFING TREATMENT TO ROOFS AND ALLIED WORKS OF BLDG NO P 200 AND P 171 CCDT KOCHI AND ADDITION ALTERATION AND SPECIAL REPAIR TO BLDG NO T 69 SNC GAS OFFICE UNDER GE NW KOCHI

Amount

Dismantling of Mangalore pattern tiles laid in dry compleate all as specified and directed by Eng-in-charge.

Dismantling existing roof treatment consisting of tarfeits etc and removal of dismantled materials compleate all as specified and directed by Eng-in-charge.

Clean the roof surface thoroughly with wire brush and remove deleterious matters and rendering min 10mm thick cm 1:3 with 3% wpc and carried out six course treatment( rate inclusive of wpc) (i) apply a coat of oil based bituminous primer @ 250 gram / square metre on the prepared surface. (ii) apply a coat of blown type bitumen grade 85/25 conforming to is:702 heated to a working temperature of 180 degree c and applied @ 1.20 kg per square metre of the surface area (iii)provide and lay 4mm thick app modified torch applied water proofing membrane weighing not less than 4.00 kg per square meter reinforced with non woven polyester matt, weighing not less than 160gm/sqm having softening point not less than 1400c, longitudinal tensile strength not less than 650 n/5 cm, tear strength of 180n (min), a static puncture resistance of 180, keeping a minimum of 10 cm over laps and 15cm end lap. iv)apply a coat of blown type bitumen grade 85/25 conforming to is:702 heated to a working temperature of 180 degree c and applied @ 1.20 kg per square metre of the surface area (v) provide and lay 4mm thick app modified torch applied water proofing membrane weighing not less than 4.00 kg per square meter reinforced with non woven polyester matt, weighing not less than 160gm/sqm having softening point not less than 1400c, longitudinal tensile strength not less than 650 n/5 cm, tear strength of 180n(min), a static puncture resistance of 180, keeping a minimum of 10 cm over laps and 15cm end lap. (vi) apply a coat of blown type bitumen grade 85/25 conforming to is:702 heated to a working temperature of 180 degree c and applied @ 1.20 kg per square metre of the surface area. (vii) apply 2 coat bituminous aluminium paint, @ 100 gm/sqm over top surface complete all as site compleate all as specified and directed by Eng-in-charge.

Treating all crumple joints with necessary treatment etc complete by racking out joints,cleaning of loose particles,providing polysterene film/filling to achieve a uniform depth of 15mm and filling up the joints with polysulphide sealant throughout the width of joints including fixing aluminium sheets of 1 mm thickness and 150mm width to with brass screws/washers compleate all as specified and directed by Eng-in-charge.

Taking down door chowkats with shutter exc 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) compleate all as specified and directed by Eng-in-charge.

Taking down Chowkats or Frame (without taking off shutter from the frame) n.exc. 1.50 Sqm compleate all as specified and directed by Eng-in-charge.

S & F solid PVC door frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube fixed in openings compleate all as specified and directed by Eng-in-charge.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site compleate all as specified and directed by Eng-in-charge.

S&F S/S Butt hinges 100mm , heavy weight, cold rolled mild steel, and fixed compleate all as specified and directed by Eng-in-charge.

M&L for 150mm size aluminum handle (ISI Marked) cast type anodized, fixed compleate all as specified and directed by Eng-in-charge. MAKE : NU-LITE/ CROWN /OXFORD

M&L for 150mm size aluminum tower bolt (ISI Marked) anodized, fixed compleate all as specified and directed by Eng-in-charge. MAKE : NU-LITE/ CROWN /OXFORD

Aluminium alloy, anodised, sliding door bolt 200mmwith hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed by Engineer -in- Charge.

S&F powder coated anodised aluminium frame for doors, windows, ventilator with one or more rebates including joining cleat for fixing etc compleate all as specified and directed by Eng-in-charge. (Minimum thickness of powder coating 50 micron)

S& F Alluminium anodised DECO Grill 10mm thick DG 104 fixed with necessary H/F/H channel ectc complete allas spd and directed. (Note : Deco grill fixed with windows with all fittings as directed by Engr -in- charge)

S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 100mm long (2 no.) suitable handle (1 no.) compleate all as specified and directed by Eng-in-charge.

S & F sheet glasses,plain 4.80mm thick glazing all with aluminum beading, glazing pin etc n. exc 0.5 sqm in each pane compleate all as specified and directed by Eng-in-charge.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples compleate all as specified and directed by Eng-in-charge.

Demolition of brick work build in CM compleate all as specified and directed by Eng-in-charge.

M&L .Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, Type C1 1:3:6 (20mm graded aggregate) compleate all as specified and directed by Eng-in-charge. (Make: Alwaye/ Perumbavoor).

M&L Providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in cement mortar 1:6, Type C1 1:3:6 (20mm graded aggregate) compleate all as specified and directed by Eng-in-charge. (Make: Alwaye/ Perumbavoor).

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc compleate all as specified and directed by Eng-in-charge.

M&L Plastering in CM 1:6, 10mm thick finished even and smooth without using extra cement compleate all as specified and directed by Eng-in-charge.

M&L rendering 15 mm(10+5) thick on fair faces of brick work or concrete surface in CM 1:4, finished even and smooth without using extra cement compleate all as specified and directed by Eng-in-charge.

M&L for rendering 5mm thick on ceiling surfaces in 1:3 cement mortar finished even &smooth without using extra cement compleate all as specified and directed by Eng-in-charge.

M&L for preparation of newly plastered ceiling surfaces and application of three coats of white wash compleate all as specified and directed by Eng-in-charge.

M&L Distmepering two coats over a coat of primer including preparation of new surfaces of walls including preparation of surface compleate all as specified and directed by Eng-in-charge.(Make: Asian- Tractor acrylic/ Berger-Bison/ Dulex- supersmooth)

Preparation of new plastered surfaces of external wall and applying 2 coat of Apex Ultima Protek system of Asian paint or equivalent of Berger/Nerolac/Dulux over a coat of antifungal primer duly applied through company authorised applicator or under company supervision using modern tools and techniques. Manufacturer and contractor shall submit performance Guarantee for period of five years compleate all as specified and directed by Eng-in-charge.

M&L complete removal of existing treatment and preparing old surface and applying 3 coat white washing on surfaces of ceiling compleate all as specified and directed by Eng-in-charge.

M&L applying 3mm thick putty on all internal wall surface compleate all as specified and directed by Eng-in-charge.(Make: J K wall putty/Asian acrylic putty/Berger wall putty)

M&L complete removal of existing treatment and preparing old surface and applying 2 coat Oil emulsion distemper on wall including priming coat compleate all as specified and directed by Eng-in-charge. (Make: Asian- Tractor acrylic/ Berger-Bison/ Dulex- supersmooth)

M&L complete removal of existing treatment and preparing old surface and applying 3 coat of whitewash complete on wall compleate all as specified and directed by Eng-in-charge. (toilet, store etc)

M&L one coat Cement paint including preparation of old surface of wall compleate all as specified and directed by Eng-in-charge.

Complete removal of existing treatment by brushing, rubbing down with water including scrapping and preparing of old treated surfaces of external walls and applying 2 coat of Apex Ultima Protek system of Asian paint or equivalent of Berger/Nerolac/Dulux over a coat of antifungal primer duly applied through company authorised applicator or under company supervision using modern tools and techniques. Manufacturer and contractor shall submit performance Guarantee for period of five years compleate all as specified and directed by Eng-in-charge.

M&L applying crack filling sealant over external wall surfaces compleate all as specified and directed by Eng-in-charge. ( Make: BASF/ IWL/Fosroc)

Dismantling of cast iron , AC pipe or reinforeced concrete drain pipes, jointed in cement mortar and taking out of trenches if required compleate all as specified and directed by Eng-in-charge.

S&F 75 mm PVC (SWR) pipes single scoketed, in any length with rubber ring joints fixed to walls compleate all as specified and directed by Eng-in-charge.

S&F 110 mm PVC (SWR) pipes single scoketed, in any length with rubber ring joints fixed to walls compleate all as specified and directed by Eng-in-charge.

S&F PVC bends 75 mm dia compleate all as specified and directed by Eng-in-charge.

S&F PVC(SWR) bends 110 mm dia compleate all as specified and directed by Eng-in-charge.

S&F PVC (SWR) branch piece single (single Y) equal or un equal 75 mm dia with access door compleate all as specified and directed by Eng-in-charge.

S&F PVC (SWR) branch piece single (single Y) equal or un equal 110 mm dia with access door compleate all as specified and directed by Eng-in-charge.

S&F PVC (SWR) junction single (single T) queal or unequal 75 mm dia with access door compleate all as specified and directed by Eng-in-charge.

S&F PVC (SWR) junction single (single T) queal or unequal 110 mm dia with access door compleate all as specified and directed by Eng-in-charge.

S&F PVC (SWR) Vent cowl 75 mm dia compleate all as specified and directed by Eng-in-charge.

S&F PVC (SWR) Vent cowl 110 mm dia compleate all as specified and directed by Eng-in-charge.

S&F PVC half round eaves gutter 180 mm dia in any length with rubber ring joints fixed to walls compleate all as specified and directed by Eng-in-charge.

S&F 180 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls (Jointing to be done with solvent cement) including PVC brackets compleate all as specified and directed by Eng-in-charge.

S&F 180mm bore PVC (SWR) Bends any radius compleate all as specified and directed by Eng-in-charge.

S&F mild steel work as in plain angle plate for securing Bands, straps, supports or stays for rainwater, cleats for securing purlins trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 compleate all as specified and directed by Eng-in-charge.

Dismantling floor/hearth and wall tiling including cement mortar backing removing serviceable tiles and rubbish off the premises compleate all as specified and directed by Eng-in-charge.

M & L for 20 mm thick screed bed or bedding layer of mortar in cement mortar 1:6 for lying floor finishes compleate all as specified and directed by Eng-in-charge.

M & L for machine cut kota stone flooring of 20-25 mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing compleate all as specified and directed by Eng-in-charge.

Dismantling timber scantlings 40 Sqcm and over in section in any position unframed compleate all as specified and directed by Eng-in-charge.

Dismantling battens for tiles, exc 15cm, shingles, etc of any size including tilting fillets compleate all as specified and directed by Eng-in-charge.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 compleate all as specified and directed by Eng-in-charge.

M & L for preparation of steel and iron surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of zinc chrome primer compleate all as specified and directed by Eng-in-charge.

S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws compleate all as specified and directed by Eng-in-charge.

S & F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws compleate all as specified and directed by Eng-in-charge.

Dismantling of wall and ceiling board (fibre, pulp, insulation etc,) any thickness including cover filets compleate all as specified and directed by Eng-in-charge.

S&F aluminium anodised snap grid frame work for false ceiling compleate all as specified and directed by Eng-in-charge.

M&L for Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long compleate all as specified and directed by Eng-in-charge.

M&L for 4mm thick non asbestos fibre cement building board fixed to aluminium frame work with work compleate all as specified and directed by Eng-in-charge.

M&L for two coat of white wash on ceiling compleate all as specified and directed by Eng-in-charge.

Demolition of brickwork built in cement mortar compleate all as specified and directed by Eng-in-charge.

M&L for Pre-cast cement concrete block masonry type C1 (1:3:6) (using 20 mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in mortar 1:6 compleate all as specified and directed by Eng-in-charge.

M&L rendering 15 mm thick on fair faces of brick work or concrete surface (external surfaces) in CM 1:6 finished even and fair (without using extra cement) compleate all as specified and directed by Eng-in-charge.

M&L for preparation of newly plastered wall surfaces and application of one coat of primer ,and two coats of oil bound distemper compleate all as specified and directed by Eng-in-charge.

M&L 100mm thick PCC type D2, 1:4:8 using 40mm graded aggregate as in sub base flooring compleate all as specified and directed by Eng-in-charge.

M&L rendering 10 mm thick as in laying wall tiles in CM 1:4 compleate all as specified and directed by Eng-in-charge.

M&L for providing Glazed ceramic tiles in vertical surface 600x400x 8mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match compleate all as specified and directed by Eng-in-charge.

M&L Anti skid jointless rectified ceramic tile of size 400x400 8mm thick over cement screed 10mm thick in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match compleate all as specified and directed by Eng-in-charge.

M&L Rectified Ceramic tiles of size 600X600 X8-9mm thickness with approved Pattern over cement sreed 10mm thick in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match compleate all as specified and directed by Eng-in-charge.

ditto as item No 72 Her-in-before as in skirting over cement screed 10mm thick in CM 1:3 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match compleate all as specified and directed by Eng-in-charge.

Demolition of plain cement concrete in ground floors not exc 15cm below or above ground level compleate all as specified and directed by Eng-in-charge.

M&L 75mm thick PCC type C2, 1:3:6 using 40mm graded aggregate as in plinth protection and hard standing compleate all as specified and directed by Eng-in-charge.

M & L for preparation & complete removal of existing treatment on internal surfaces of walls, and applying 3 mm thick wall care putty on old plaster surfaces, preparatory to distempering & applying two coats of distemper oil emulsion all as specified and directed by Engineer in charge compleate all as specified and directed by Eng-in-charge.

M&L for one coat of cement base paint including preparation of old treated surface compleate all as specified and directed by Eng-in-charge.

S & F in repair, vitreous china wash hand basin, 550 x 400 mm bracket incl waste fittings etc compleate all as specified and directed by Eng-in-charge.

S&F low density polyethylene pipes (LDPE) 40 mm bore of pressure rating 6 Kgf/cm2 fixed complete to walls or in floors for urinals, wash basin etc compleate all as specified and directed by Eng-in-charge.

S & F in repairs, IWC orissa pattern (white), size 580X440mm with integral foot rest compleate all as specified and directed by Eng-in-charge.

S & F 10 litre capacity PVC flushing cistern with accessories complete, including all connections, ISI marked compleate all as specified and directed by Eng-in-charge.

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighin 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc compleate all as specified and directed by Eng-in-charge.

S&F anodised aluminium door shutters,aluminium section weighing 0.55 kg/m ncluding necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc compleate all as specified and directed by Eng-in-charge.

M&L 9 mm thick prelaminated partical board, interior grade, prelaminated both sides with decorative choice laminations, fixed with screws to timber frame work or inserted in aluminium frame work compleate all as specified and directed by Eng-in-charge.

M & L sheet glass ordinary quality 5.5mm thick and glazing with oil putty in squares exc. 0.5 sqm each pane compleate all as specified and directed by Eng-in-charge.

S&F Galvanised mild steel wire cloth 0.63 mm nominal dia and average width of aperture 1.40 mm compleate all as specified and directed by Eng-in-charge.

S&F aluminium body(die cast) body, in door closer hydraulically regulated, designation No 3, universal type, suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed compleate all as specified and directed by Eng-in-charge.

S&F powder coated sliding window shutter with frame, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, aluminium anodized snap beading, screw etc.(minimum thickness of powder coating 50 micron) including 5mm thick plain glass glazing compleate all as specified and directed by Eng-in-charge.

Demolition of RCC slab of any description and in any position mot otherwside specifically provided for compleate all as specified and directed by Eng-in-charge.

M & L RCC Type B1 1:2:4 (20mm graded aggregate) for slabs supporting on walls,beams, roofs, deck slabsand in shelves and like complete all as specified and directed by Engineer in Charge

M & L formwork to chullah hoods, chajjas, trough and similar items including edges finished rough surfaces of concrete compleate all as specified and directed by Eng-in-charge.

Form work to soffit of roof slab. surface finished fair, flat surface compleate all as specified and directed by Eng-in-charge.

Mild steel TMT bars 10mm dia cut to length bent to shape required incl. cranking bending spirally for hoop for columns ,hooking ends and binding with and including mild steel wire not less than 0.9mm dia or for compleate all as specified and directed by Eng-in-charge.

M&L for mild steel TMT bars 6 to 8 mm dia and over cut to length bent to shape reqd inclg cranking bending spirally for hooping for columns hooking ends & binding with & inclg mild steel wire (annealed) not less than 0.9 mm compleate all as specified and directed by Eng-in-charge.

M&L 20mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade compleate all as specified and directed by Eng-in-charge.

M&L in repair 18mm thick Rubwood as in CB shutter,shelves etc cut to shape as specified and fixed with screws compleate all as specified and directed by Eng-in-charge. (Make: Rubco)

M&L in repair 12mm thick Rubwood as in CB's cut to shape as specified and fixed with screws compleate all as specified and directed by Eng-in-charge. (Make: Rubco)

S&F 100mm stainless steel hinges/ box hinges for cupboards fixed with screws compleate all as specified and directed by Eng-in-charge. ( Make:Crown / Jyothi / Argent )

S&F 100mm long stainless steel bow handle for cupboards fixed with screws as specified and directed by Engr in charge( Make:Crown / Jyothi / Argent )

S&F magnetic catch for cupboard shutter as specified by E ngr in charge.( Make:Crown / Jyothi / Argent )

French polishing to wood or wooden surface including preperation and a coat of wood filler etc compleate all as specified and directed by Eng-in-charge. (Make: Asian Paint / Nerolac/ Berger)

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc compleate all as specified and directed by Eng-in-charge.

M&L point wiring with 1.5 Sqmm PVC insulated unsheathed with proper colour coding FRLSH multistranded single core copper conductor cable in PVC concealed conduit rigid, non metallic medium grade with suitable size concealed in wall/roof except beam, column and RCC roof including chases cutting incl making good wall surfaces with existing surfaces and 1.6 mm thick MS sheet pressed terminal box (recessed) with 3 mm thick PVC laminated sheet top cover for accommodating switches socket regulators etc. incl 1.5 Sqmm PVC insulated copper conductor as earth continuity wire for as the following: (a) one light point controlled, one way switch 5 Amp compleate all as specified and directed by Eng-in-charge.

(b) One fan,point controlled, one way switch 5 Amp compleate all as specified and directed by Eng-in-charge.

(c) 5 pin 5/6 Amps switch socket outlet point on independent board compleate all as specified and directed by Eng-in-charge.

(d) 5 pin 5/6 Amps switch socket outlet point on same board compleate all as specified and directed by Eng-in-charge.

(e) 6 pin 15 Amps switch socket outlet point on independent board with 2.5 Sqmm (FRLSH) PVC insulated unsheathed stranded copper conductor with 2.5 Sqmm PVC (FRLSH) insulated stranded copper wire for continuous earthing compleate all as specified and directed by Eng-in-charge.

S&F ceiling rose, 3 phase/pvc/polycarbonate, isolated body compleate all as specified and directed by Eng-in-charge. Make : Anchor/Legrand/Havells.

S&F switch socket 5 pin 5 amps, 230 volts, 50 Hz, 2 in one flush type with cover plate ccompleate all as specified and directed by Eng-in-charge.

S&F switch socket 6 pin 5 and 15 amps, 230 volts, 50 Hz flush type with cover plate compleate all as specified and directed by Eng-in-charge. Make : Anchor/Legrand/Havells.

S&F switch piano flush type 5 Amps one way with cover plate compleate all as specified and directed by Eng-in-charge. Make : Anchor/Legrand/Havells.

S&F switch piano flush type 15 Amp one way with cover plate compleate all as specified and directed by Eng-in-charge. Make : Anchor/Legrand/Havells.

S&F stepped type electronic fan regulator flush type 230 volts, 50 Hz compleate all as specified and directed by Eng-in-charge. Make : Anchor/Legrand/Havells

Supply & fix Regal Batten for LED tube lights, both side connection type and LED tube rod 1 x 20 Watt, both side connection compleate all as specified and directed by Eng-in-charge. Make : Havells Cat Part No. REGALBATTENT8 upto 1x822W SSBSWH for Regal Batten & CRYSTAL 1213T8DSTL20W LED 8655 GLASS for tube rod or Surya/Wipro complete all as specified and directed

S&F LED ceiling light fitting 2'x2' 36 Watt recessed full lit luminaire with glare free uniform illumination (100 lumen/watt) Make : Crompton Cat Part No. LCTLRF6-36-CDL compleate all as specified and directed by Eng-in-charge.

M&L for sub main wiring with 2 runs of 4 Sqmm (FRLSH) PVC insulated unsheathed multistranded copper conductor cable and 1 run of 4 Sqmm (FRLSH) cable as earth continuity wire and including PVC conduit concealed in wall/floor including cutting chesses and making good distrubed surface to match with existing surface. Note -1. 2 runs of 4 Sqmm FRLSH and 1 run of 4 Sqmm FRLSH copper conductor shall be measured as one unit length compleate all as specified and directed by Eng-in-charge.

M&L for sub main wiring with 2 runs of 6 Sqmm (FRLSH) PVC insulated unsheathed multistranded copper conductor cable and 1 run of 6 Sqmm (FRLSH) cable as earth continuity wire and including PVC conduit concealed in wall/floor including cutting chesses and making good distrubed surface to match with existing surface compleate all as specified and directed by Eng-in-charge. Note -1. 2 runs of 6 Sqmm FRLSH and 1 run of 6 Sqmm FRLSH copper conductor shall be measured as one unit length. 2. including taking down old unserviceable sub main wiring.

Taking down old stop valve,stop cock,bib cock,from existing position including all fittings compleate all as specified and directed by Eng-in-charge.

S&F stop valve (angle type) cast copper alloy high pressure, screwed for 15mm dia CP fancy type (half turn) compleate all as specified and directed by Eng-in-charge.

S&F of bib cock long body chromium plated with flange and aerator CP fancy type of size 15mm compleate all as specified and directed by Eng-in-charge.

S&F of low density polythene pipe 16mm dia (outer) 450 mm long for cold water and taking down old one complete with brass union on both sides to suit 15mm GI pipe compleate all as specified and directed by Eng-in-charge.

S&F on wall/ceiling (concealed) CPVC pipe 25 mm dia SDR 11 & plain SDR 11 fittings compleate all as specified and directed by Eng-in-charge.

S&F on wall / ceiling (concealed) CPVC pipe 20mm dia SDR 11 & plain SDR 11 fittings compleate all as specified and directed by Eng-in-charge.

M&L for CPVC Ball valve of size 25 mm dia suitable for CPVC pipe incl necessary fittings compleate all as specified and directed by Eng-in-charge. Make : Supreme/Eurotech/Astral/SFMC

M&L for CPVC Ball valve of size 20 mm dia suitable for CPVC pipe incl necessary fittings compleate all as specified and directed by Eng-in-charge. Make : Supreme/Eurotech/Astral/SFMC

S&F float valve synthetic (PVC) of size 25 mm dia high pressure with polythene ball of size 6" dia and flynut compleate all as specified and directed by Eng-in-charge.

Supply and fixing health faucet ABS body with wall hook and 1 metre SS braided rubber hose pipe, including taking out old one all as per specified and directed by engineer-in-cherge (Make : Model No. F8030102 of Cera or Prayag/Hindware/Jaguar)

S&F 15mm angle valve, quarter turn with flange type, chromium plated for fixing with CPVC pipe complete specified and directed by the Engr-in-charge. Make : Cera Model No. F2004201

S&F of Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position of capacity 500 litres compleate all as specified and directed by Eng-in-charge. Make : Sintex (ISI)/ Aquatech

Taking down old unserviceable GI tubing of size 25mm compleate all as specified and directed by Eng-in-charge.

Taking down old unserviceable GI tubing of size 20mm compleate all as specified and directed by Eng-in-charge.

S&F on wall / ceiling (concealed) CPVC pipe 25 mm dia SDR 11 & plain SDR 11 fittings compleate all as specified and directed by Engr-in-charge.Make:- Supreme

S&F on wall / ceiling (concealed) CPVC pipe 20mm dia SDR 11 & plain SDR 11 fittings compleate all as specified and directed by Engr-in-charge. Make:- Supreme

Taking down old unserviceable GI tubing of size 25mm compleate all as specified and directed by Engr-in-charge.

Taking down old unserviceable GI tubing of size 20mm compleate all as specified and directed by Engr-in-charge.

Supply and fix in repairs Ball brass valves (PTMT) of size 25 mm dia high pressure,with polythene float and flynut complete,screwed for iron pipe or brass ferrule and fixed compleate all as specified and directed by Engr-in-charge.

Supply and fixing in replacement of Rotational mouldede polyethylene water storage tanks (cylinderical vertical with closed top) hoisted & fixed in position of capacity 1000 liters compleate all as specified and directed by Engr-in-charge.

MS BUILDERS

HEAVEN ENGINEERS AND CONTRACTORS

Anaswara Constructions

Albert Rebello and Company

SUKU CONSTRUCTIONS

ANIE JOHN CONTRACTORS