REPAIRS TO FENCINGS, ROLLING SHUTTERS, GATES, GUARDBARS AND OTHER ALLIED WORKS AT NOFRA, NAUSENA BAGH, NAE, MES COMPLEX, INS SARDAR PATEL, NCB AND INAS

Amount

Dismantling of fencing wire mesh any typecomplete all as specifed and as directed by Engineer in Charge.

Fixing only Chain link MS galvanisd fencing 4mm dia galvanised steel wire 75mmX75mm mesh ,made up into matrtresses or cages incl line wire ,any type of standared ,rails staining bolt etc complete all as specifed and as directed. Complete all as spd and directed by Engineer in Charge

Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and directed.

S & F mild steel round bars 10mm dia, cut to length, hooking ends confirming to Fe-410-W(Gde E-250) quality - A or Fe 290 (Gde - E-165) complete all as spd and directed.

Demolition of brickwork or stone/boulders/block masonry, built in cement mortar including all quoins, arches, pillars, ashlar facing, dressed stonework, precast concrete artilcles and precast concrete block walling etc. Complete all as specified and directed.

Taking down cement plaster or terrazzo from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified.

M&L Squared rubble walling with Porbandar stone masonary in CM 1:6 brought to courses, complete all as specified & directed by Engr-in-charge.

Ditto as above item No.3 but except stone, Complete all as specified and directed.

Rendering 15mm thick on fair faces of Porbandar stone masonary surface in CM 1:4 complete all as specified and directed by Engr-in-charge.

Preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of white primer complete all as specified and directed.

Preparation of old plastered surfaces of walls and applying one coats of cement base paint complete all as specified and directed by Engineer in Charge .

Preparation of old treated steel surfaces of any description(Steel gates , Embedded Angles etc) , over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified.

Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces complete all as specified.

Taking down aluminum composite panels any type complete all as specifed and as directed by Engineer in Charge

S&F for Aluminium Composite panels in all colours, any shape, of approved brand for external /internal wall cladding at all heights and elevations including necessary aluminium composite panel consist of 3mm thermoplastic core of anti oxidant LDPE sandwitched between two sking of 0.50 mm thick alloy sheet making a total sheet thickness of 4mm. The surface shall be finished with PU base coating on the top side and service coating on the reverse side shall be with a polymer paint. The system to be fixed to the brick/ stone/masonry/RCC walls/framed structure with necessaary clamps, bracket and anchor fasteners fixed over and including base frame fabricated with GI square pipe of size 25mm x 25mm including stainless steel screws, nut bolts, washers, cleats, weather silicon sealent for groove filling, backer rods etc, complete all as per manufacturer instrsuction and all as specified and as directed by Engr-in-Charge. All clamps and brackets shall be hot dipped galvanised minimum 20 microns, (items include cost of GI frame, ACP Panels, Cramps, weather sealant, gasket, foam, fixtures,scaffolding, all machineries and any fastening strips, nuts,bolts, rivets, washers, etc., complete all as specified and directed.

S&F for Aluminium Composite panels in all colours, CNC cut, of approved brand for external /internal wall cladding at all heights and elevations including necessary aluminium composite panel consist of 3mm thermoplastic core of anti oxidant LDPE sandwitched between two sking of 0.50 mm thick alloy sheet making a total sheet thickness of 4mm. The surface shall be finished with PU base coating on the top side and service coating on the reverse side shall be with a polymer paint. The system to be fixed to the brick/ stone/masonry/RCC walls/framed structure with necessaary clamps, bracket and anchor fasteners fixed over and including base frame fabricated with GI square pipe of size 25mm x 25mm with Tmm thickness in 600mm x 600mm size of grid including stainless steel screws, nut bolts, washers, cleats, weather silicon sealent for groove filling, backer rods etc, complete all as per manufacturer instrsuction and all as specified and as directed by Engr-in-Charge. All clamps and brackets shall be hot dipped galvanised minimum 20 microns, (items include cost of GI frame, ACP Panels, CNC cutting, Cramps, weather sealant, gasket, foam, fixtures,scaffolding, all machineries and any fastening strips, nuts,bolts, rivets, washers, etc., complete all as specified and directed.

Dismantling of mild steel work of any description not otherwise provided for all as specified and directed .

Hand rails, half round or other stock section or core for wooden hand-rail straight portion,Gates , Grating drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specifed and as directed by Engineer in Charge.

S & F in repair to Framed work ( Fe 410 -W(Gde-E- 250) quality-A)- as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete complete all as spd and directed by Engineer in Charge

Taking down old u/s Aluminium Window/door sliding section removing from Sliding track incl with all glass /wire mesh fitting complete all as spd and directed by Engineer in Charge

S& F in repair to Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chanrge

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge

S & F Aluminium Partition of standard section 63.5 x 38.1 x 1.31 mm wall thickness including sheet panes, necessary jointing cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws complete all as specified and directed by Engineer in Charge

S & F Solar control film 25 micron reflective type (gareware sun control or equiva?lent) on glass etc complete all as specified and directed by Engineer in Charge

S&F in Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.complete all as spd

S&F in repairs Aluminium alloy wire cloth,0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples.complete all as spd

S & F in repairs Double action floor spring hydraulically regulated madeup of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified.

S & F in repair Mortice aluminium 2 lever lock, vertical type, size 100 mm complete all as specified.

S&F as in repairs Mild steel pipes/ rolled sections, MS sheet min 5mm thk with powder coating, Fe 410 -W (Gde- E- 250) quality- A as in framing for cladding, rafters; purlins, view cutter, fixed with angle cleats or other connecting plates etc incl embedded and drilled and bolt fixing with Existing wall surfaces using PCC ( PCC Shall be paid and separety ) all as specified & directed by Engr-in-charge.

S&F in repairs Concertina Coil , punched tape 2.60 mm dia high tensile spring steel wire, dia of coil 610mm, when stretched the length shall be 6.00m in one coil, (weight of coil shall not less than 1.30kg/m) and tied to barbed wire with and including provision of steel clips @ 5 clips spiral in one row complete without coating and taking down old concertina coil .all as directed by Engr-in-Charge.

Demolition of concrete of any description and in any position not otherwise specifically provided for cement concrete (unreinforced) complete including removing debries ouside MD land all as specified and directed.

M & L for 50mm thick Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection,Floor topping etc , surfaces finished of concrete flooring with brooming complete all as spd u including provision of necessary construction joints filled with bitumen filler etc complete all as directed by Engr-in-Charge

M&L cement concrete 1:4 :8 type D-2 (40mm graded agg) in foundation filling and mass concrete.complete all as specifed and as directed by Engineer in Charge.

Sand filling under paver blocks for cushion Complete all as specified and directed.

Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement pigment to match, Complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 grade, finished with grey cement and pigment, complete all as directed.

All as per above Except Interlocking tiles including filling with sand cushioning ( where ever required ) including levelled with Existing tiled surfaces Complete all as spd and directed by Engineer in Charge. ( Note :- Sand and PCC shall be paid and measured Separtely )

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons, compound wall etc.laid dry beded in any mortor complete all as specified.

M&L 20mm thick Granite (of any type)tiles machine cut, in skirting/dado /Pillars etc laid over CM 1:4 , 15mm tk cement screed and jointed with grey cement slurry, and pointed with white cement with admixture ofpigment to match the shade ofgranite stone including grinding and polishing complete all as specified

PCC (1:2:4) type B-1 20 mm graded concrete for embedding the angle fencing posts, including necessary formwork, complete all as directed by Engr-in-Charge.

RUDRAAY CONSTRUCTION

BABUBHAI BHIMABHAI PANDAVADRA

M/S Rajendra Constructions

K B N TRADERS

m/s prakash enterprise

Leo Elevator Company

SANVI ASSOCIATES

ALBA AC AND REF SERVICES