SPECIAL REPAIRS TO SEWAGE LINE AND PROVN OF INTERLOCKING TILES IN ALKAPURI RESIDENTIAL COMPLEX OF CQA SV UNDER AGE BR EAST AT GE DEHU ROAD

Amount

Excavating in Trenches, not exc. 1.50 M wide and not exc. 1.50 M in depth, for Foundation, Manhole, Shafts, well cesspits, pier holes n.exc 10 Sqm on plan and n.esc 1.5m in depth and getting out in Soft/ Loose Soil, complete all as specified and as directed.

Excavating in Trenches, not exc. 1.50 M wide and not exc. 1.50 M in depth, for Foundation, Manhole, Shafts, well cesspits, pier holes n.exc 10 Sqm on plan and n.esc 1.5m in depth and getting out in Hard/ Dense Soil, complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quions, pillars etc all as specified and directed.

M&L for precast Solid cement concrete block masonary exc 10cm width type C1 1:3:6 using 20mm graded aggregates using solid blocks of PCC design mix grade C5 set in CM 1:6 complete all as specified and directed

Demolition of reinforced cement concrete of cover slab of septic tank, manhole covers etc complete all as specified and as directed.

M&L for reinforced cement concrete (nominal mix ) type A-1, 1:2:4 using 20mm graded stone aggregates as in cover slabs of septic tanks all as specified and as directed.

Use and waste of formwork to soffits & edges of cover slabs of septic tanks and similar work not exceeding 200 mm thick for fair finished flat surfaces of concrete all as specified and as directed.

M&L RCC (1:2:4) type B1 using 20 mm graded aggregate as in lintels/coping over 1.5 m span etc inluding weathring slightly rounded or chamferred angles complete all as specified and directed. Note: Reinforcement shall be measured separately.

M&L for TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending hooking etc & binding with and including mild steel binding steel wire (annealed) not less than 0.9mm dia.

M&L for TMT bars 6 to 8mm dia cut to length bent to shape required, including cranking, bending hooking etc & binding with and including mild steel binding steel wire (annealed) not less than 0.9mm dia.

M&L Rendering 15mm thick on Brick Work in Cement Mortar (1:4), finished Plastered Surfaces Even and Smooth with spong finish using water proofing compound @3%, complete all as specified and as directed.

Supply only integral water proofing compound. Make Dr fixit

Demolition and breaking up drain pipes RCC set in cement mortar 150mm bore complete all as specified and directed. NOTE: (i)The measurements shall be taken long the centre line of pipe and fittings. (ii)Excavation work shall be measured separately.

Demolition and breaking up drain pipes RCC set in cement mortar 200mm bore complete all as specified and directed. NOTE: (i)The measurements shall be taken long the centre line of pipe and fittings. (ii)Excavation work shall be measured separately.

M/L 150mm bore reinforced cement concrete pipe Class NP2 laid and jointed complete with collars and laid in trenches including testing all as specified and directed.

M/L 200mm bore reinforced cement concrete pipe Class NP2 laid and jointed complete with collars and laid in trenches including testing all as specified and directed.

Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 250mm in Soft/Loose Soil, complete all as specified and as directed.

Removing the excavated surplus soils exc 1.5KM n.exc 5 KM and depositings where directed at a level n.exc 1.5 mtr above the starting point (Note : Site of disposal of soil is to located by Contractor himself. If any extra lead for disposal of soil behind 5km will be bear by the Contractor)

M&L providing plain cement concrete type B1, 1:2:4 ,(using 20 mm graded stone aggregate) as in surface channels and drains forming fair finished drain or channel inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc.all as specified and directed. NOTE : Deduction from the volume of concrete shall be made for the channel opening

Material & labour for Cement concrete type C2, (1:3:6) (20mm graded stone aggregate) bed to drain pipe including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore pipe. NOTE:(i)Thickness of bed below the barrel of pipes100mm .(ii)Width of bed: Outer diameter of drain pipes (not of socket/collars) plus 30 cm.

Material & labour for Cement concrete type C2, (1:3:6) (20mm graded stone aggregate) bed to drain pipe including packing under and haunching against the sides of pipes after they are laid and tested for 200mm bore pipe. NOTE:(i)Thickness of bed below the barrel of pipes150mm .(ii)Width of bed: Outer diameter of drain pipes (not of socket/collars) plus 30 cm.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for internal dia of pipe 150mm

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for internal dia of pipe 225mm

M & L for precast reinforced cement concrete type B-1, 1:2:4, using 20mm graded stone aggregates as in man hole covers/septic tanks including formwork/moulds and set in cement mortar 1:4 all as specified and as directed. Note :- Reinforcement shall be measured seperately.

Taking out water in fully covered tanker vehicle by sucking with pump set from septic tank, soakpit and the same will be disposed at out side MOD Land (The location at out side MOD land for disposal of water from septic tank is to located by the Contractor himself)

Cleaning/clearing & Maintanance of sewage lines, manholes including CI stacks, incl under ground sewage lines any depth by removing any type of blockage from sewage drain upto and including 100mm dia by rodding or any other means from manholes to manholes or from trap and flusing with water after cleaning including manholes. Sludge/sludge water to be disposed off through sludge in form of semi solid/loose state will be disposed off by burring with in a distance not exceeding 250 metres outside the perphery of defence land including taking off manhole covers and refixing the same after cleaning. Sewage lines cleared/cleaned under this item is to be maintained and kept fully functional by removing any type of blockage.

Cleaning/clearing & Maintanance of sewage lines, manholes including CI stacks, incl under ground sewage lines any depth by removing any type of blockage from sewage drain upto and including 150mm dia by rodding or any other means from manholes to manholes or from trap and flusing with water after cleaning including manholes. Sludge/sludge water to be disposed off through sludge in form of semi solid/loose state will be disposed off by burring with in a distance not exceeding 250 metres outside the perphery of defence land including taking off manhole covers and refixing the same after cleaning. Sewage lines cleared/cleaned under this item is to be maintained and kept fully functional by removing any type of blockage.

Cleaning/clearing & Maintanance of sewage lines, manholes including CI stacks, incl under ground sewage lines any depth by removing any type of blockage from sewage drain upto and including 200mm dia by rodding or any other means from manholes to manholes or from trap and flusing with water after cleaning including manholes. Sludge/sludge water to be disposed off through sludge in form of semi solid/loose state will be disposed off by burring with in a distance not exceeding 250 metres outside the perphery of defence land including taking off manhole covers and refixing the same after cleaning. Sewage lines cleared/cleaned under this item is to be maintained and kept fully functional by removing any type of blockage.

Cleaning of blocked WC/gully trap including and up to first manhole by manual labour as well flushing with clean water making the WC seat operational complete all as specified and directed by Engr-in-Charge

Taking out Complete removal of semi solid and in liquid sunspension sludge from manholes/septic tank/sokage well including pumping of water and removing the same by means of covered vehicles to a distance exc 1.5 0 KM to 3.0 Km and burying the same in ground.

Demolition and breaking up drain pipes any dia (Salt glazed ware, PVC,AC ) set in cement mortar

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

S&F 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors/walls

-do- as above but 110mm dia

M&L for PVC (SWR) bends of any radius with oval and access door of 75mm dia

-do- as above but 110mm dia

S&F in repairs Grating doom 100mm dia of PTMT (Minimum weight 25gms). Make : CAT NO:111 OF MAKE PRAYAG OR EQUIVALENT.

M&L PVC (SWR) branch piece single (single ‘Y’) equal or unequal with oval access door suitable for 75mm bore pipe with access door

M&Lfor PVC (SWR) vent cowl of 110mm dia

S&F cast iron Nahani trap with grating of diameter of outlet 100mm including jointing to waste pipe fixed in cement concrete type B1 (1:2:4).

M&L(SWG) gully trap 150mm setting and jointing with solvent cement.

S&F in repair vitreous china, squatting pan of 'Orissa' pattern, long pan, size 580 mm x 440 mm, white, with 'P' of 'S' Trap, front or back inlet and foot rests any pattern, including concrete bedding and PVC low level flushing cistern 10 Ltr capacity including 32mm PVC flush pipe, all internal fitting, inlet, outlet pipe connections etc. complete all as specified and as directed.

S&F in repairs white vitreous china wash down water closet pan(pedestal pattern) with ‘P’ or ‘S’ trap, plastic water closet seat, white, closed pattern with recessed bottom cover and mild sted chromium plated hinge including connection to drow pipe and flushing pipe all as specified

Demolition of cement concrete in ground floors and pavings n.exc 15 cm thickness (below or above ground level)

M&L for loose filling with broken bricks 80 to 150mm in soakage pit.

S & F Glass dividing strips, 3 mm thick 38 mm width of strip

M&L Hardcore of guage Broken stone n. exc 63mm deposited, spread and levelled in layers n exc 150mm thick, watered and rolled/ rammed to a true surface complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregates) as in sub base 75mm thick.

M&L for cement concrete 1:3:6 Type C-2 (using 40mm graded stone aggregate)75 mm thick in plinth protection and courtyard, finished cement surfaces even and smooth without using extra cement complete all as specified

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for coloured Non skid ceramic tiles of size 300x300mmx7mm thick in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 20mm thick screed bed in CM (1:6).

M&L glazed ceramic coloured tiles of size 450 x 300 x 7mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar 1:4 and including dismantling existing floor tiling complete, all as specified.

M&L for coloured glzed ceramic tiles in vertical surfaces of size 300x200x7mm thick of colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles including backing coat etc complete.

Material and labour for non skid coloured ceramic tiles of size 400mm x 400mm x 10 mm thick, pattern as approved by GE, set and jointed over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

Taking down cement plaster on brick/ stone wall including raking out joints, hacking for key scrubbing down with water etc. and clearing off the premises.

M&L for rendering 15mm thick in CM (1:6) on fair faces of brick/concrete surfaces finished even and smooth without using extra cement.

M&L for preparation of newly plastered surfaces and applying two coats of cement base paint using supersnowcem only over a coat of cement primer as specified and directed.

S&F in reapir PVC low level flushing cistern 10 ltr capacity with brackets of approval Make and all necessary fittings etc complete all as directed and specified.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal 15mm dia

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal 20mm dia

Refixing 20 mm dia old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.

Refixing 15 mm dia old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.

M&L for GI tubing 15mm dia medium grade with all fittings & fixed complete to walls & ceiling or laid in floors in repairs

M&L for GI tubing 20mm dia medium grade with all fittings & fixtures complete laid in trenches fixed in repairs

M&L for cutting chases, pinning in making good to face for concealed water tubing in brick walls

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm

S&F in repair EWC Seat Cover Cat No. 2308 Carina any colour of size Make-Cera

S&F in repairs waste coupling of dia 31/32 mm (H/T) of PTMT. Make : CAT NO:101 OF MAKE PRAYAG OR EQUIVALENT.

S&F in repairs waste coupling of dia 38/40 mm (F/T) of PTMT. Make : CAT NO:102 OF MAKE PRAYAG OR EQUIVALENT.

Dismantling water tanks and removing to site up to 500Ltr capacity.

Dismantling water tanks and removing to site exc 500Ltr but n. exc 1000Ltr capacity.

S&F rotational moulded Polythene (HDPE) double layer water tanks, cylindrical & vertical type 500 Litres capacity hoisted and fixed in position including provision of 20mm/15mm dia. spouts for connecting inlet, outlet, over flow and washout pipes.

All as per item No. 44 above but 1000 litres.

M&L for 75mm thick PCC type D2 (1:4:8, using 40mm graded stone aggregate) as in sub base of interlocking reflective pavers block.

M & L for PCC 1:4:8, type D-2, using (40mm graded stone aggregate) as in foundations, filling and mass concrete.

M&L for laying machine pressed precast conctete interlocking reflective coloured pavers block any shape and size confirming to IS 15658-2006 of 55mm to 60mm thick, M-35 Grade all as specified and directed by Engr-in-Charge at site.

M&L for Brick work with sub-class ‘B’ bricks straight or curved on plan exc. 6m mean radius in half brick thick walls built in cement mortar (1:4).

M&L Brick work with fly ash bricks, conforming to IS- 12894:2002, Non modular, class designation 75, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 etc including demolition of brickwork built in cement mortar and rubbish off the premises complete all as specified and directed.

M&L for PCC type B1(1:2:4, using 20mm graded stone aggregate) as in edging all as specified and directed.

M&L for preparing new plastered surfaces & applying two coats of applying two coats of synthetic enamel paint.

M&L Cement concrete in surface channels and as in drains type D-2 (1:2:4) with 20 mm graded stone aggregate.

M & L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc.

M & L for Sand filling under floors or in foundations including watering and consolidation all as specified and directed.

AVS CONSTRUCTION

Ridhi Constructions

M/S B.A. GAIKWAD