CA NO. CWE/AMB/NORTH/T-04 OF 2021-22 SPECIAL REPAIRS TO OR MD ACCN BLOCK NO. 72/1 TO 72/6, CW LINE OF 4002 FD HOSP UNDER AGE B/R-I OF GE(NORTH) AMBALA CANTT

Amount

SCHEDULE A PART I (B/R WORKS) Taking down cement plaster including raking out joints hacking for key, scrubbing down with water etc, and removal of debries to distance exc 250 mtr but n exc 500 mtr complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description, in ground floor and pavings not exceeding 15 cm thickness (below or above ground level) and removal of debries to distance exc 250 mtr but n exc 500 mtr complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position including reinforcement cut as required to facilitate demolition and scraping, separating and cleaning of reinforcement and removal of debries to distance exc 250 mtr but n exc 500 mtr complete all as specified and as directed.

Demolition of brickwork built in cement mortar including all quoins, arches, pillars etc, and stacking of serviceable bricks and removal of debries to distance exc 250 mtr but n exc 500 mtr complete all as specified and as directed.

Material and labour for rendering, 15 mm thick, in cement mortar 1:4, mixed with water proofing compound @ 2% by weight of cement or as per manufacturer’s instructions, on fair faces of brick work or concrete surfaces of any description finished even and smooth without using extra cement complete all as specified and as directed. Note: Supply only integral water proofing shall be measured and paid separately.

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete walls in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

Material and labour for brickwork, with subclass 'B' bricks, straight or curved on plan to any radius, exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed.

All as above Item No 8.00 but except bricks complete all as specified and as directed. Note: Old serviceable bricks as obtained from serial item No 4.00 hereinbefore shall be reused after cleaning the bricks. The rate quoted shall include for cleaning the bricks also.

Material and labour for brickwork, with old size sub class 'B' bricks, straight or curved on plan to any radius, exceeding 6 metre mean radius built in cement mortar 1:4 as in half brick thick wall complete all as specified and as directed.

Material and labour for rendering 10mm thick on concrete walls in cement mortar 1:3, surfaces finished even and smooth without using extra cement on ceiling complete all as specified and as directed.

Material and labour for providing cement concrete 1:2:4 type B-1 using 20mm graded aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

Material and labour for 10mm thick coloured cement concrete paver tiles (endura tiles) of size 300mmx 300mm , over and including 20mm thick screed in cement mortar (1:4) as in floor base and jointed & pointed with coloured cement slurry mixed with pigment to match shade of the slab including cutting complete all as specified and directed.

Material and labour for 10mm thick coloured cement concrete paver tiles (endura tiles) of size 300mmx 300mm , over and including 10mm thick rendering in cement mortar (1:4) base as in skirting and jointed & pointed with coloured cement slurry mixed with pigment to match shade of the slab including cutting complete all as specified and directed.

Material and labour for marble work, Baroda green, 16-18mm thick, one piece in width and length not less than 1.8 m , laid over and including 15mm thick bedding layer in cement mortar (1:4), table rubbed & polished in shelves etc including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of marble including rounding of front edge and finally granite finish polishing ,complete all as specified and as directed.

Dismantling floor, hearth, or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premise and removal of debries to distance exc 250 mtr but n exc 500 mtr complete all as specified and as directed.

Material and labour for premium quality, joint free, printed glazed coloured ceramic tiles of size 300 x 450 x 7mm thick on vertical surfaces of walls over and including 10mm thick rough finished plaster in cement mortar (1:4), set, jointed in neat cement slurry and set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

Material and labour for premium quality, joint free, non skid light coloured ceramic tiles (Square/rectangular), area of each tile exceeding 0.18 sqm and not exceeding 0.36 sqm and 7 to 8 mm thick, laid in floor over and including cement screed bed 15mm thick in cement mortar (1:4) ,set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

Material and labour for premium quality, joint free, non skid light coloured ceramic tiles (Square/rectangular), area of each tile exceeding 0.18 sqm and not exceeding 0.36 sqm and 7 to 8 mm thick, laid in skirting, dados, risers and steps over and including rendering 10mm thick in cement mortar (1:4) ,set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

Material and labour for use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports overhangs, etc. also splays between floors and beams, etc. in rough finished flat surfaces of concrete complete specified and directed.

Material and labour for precast reinforced cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregates, in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and setting in mortar cement mortar (1:4) with joints to match including necassary form work and mouldings complete all as specified and directed.

Material and labour for PCC 1:3:6 type C-2 (using 40 mm graded mechanically crushed stone aggregate), 75mm thick, as in plinth protection/PCC path and paving, laid in panels of area not exceeding 1.20 sqm with 12mm wide joints filled with mastic (using bitumen and sand mixture applied hot in the ratio of 1:3 by weight) formed at the end of each panel and change in direction of plinth protection/PCC Path and paving and finishing the top surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 25mm thick cement concrete (1:2:4) type B-0 using 12.5 mm graded stone aggregates as in bedding layer under floor surface finished even and faircomplete all as specified and directed.

Material and labour for PCC (1:3:6) type C-1 (using 20mm graded stone aggregates), as in surface channel or drain inclusive using of necessary form work for fair finished sueface complete all as specified and as directed.

Extra forming fair finishing of drain or channel 30cm inner grith in cement concrete using extra cement including forms, moulds mitrel gloppid ends etc. complete all as specified and directed.

Material and labour for pre-painted galvalume, aluminuim zinc coating, GI based corrugated steel sheet, 0.50mm thick, AZ-150 conforming to IS-15961, colour as directed, having tensile strength of 550 MPa, as in roof covering/cladding to wall, fixed with self tapping screws including taking down of old sheets of any descriptions and removal from site complete all as specified and as directed. Note- The sheets shall have super durable polyester quality paint of approved colour, 150 gm/sqm total on both sides, suitable for exterior application conforming to IS-15965.

Material and labour for pre-painted galvalume, aluminuim zinc coating, GI based Plain steel sheet, 0.50mm thick, colour as directed, having tensile strength of 550 MPa, as in roof covering/cladding to wall, fixed with self tapping screws including taking down of old sheets of any descriptions and removal from site complete all as specified and as directed. Note- The sheets shall have super durable polyester quality paint of approved colour, 150 gm/sqm total on both sides, suitable for exterior application conforming to IS-15965.

Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) set in cement mortar (internal dia of pipe in mm) 100mm complete all as specified and directed.

Taking down chowkats or frames with shutter, area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish including removal of serviceable/unserviceable material from site complete all as specified and directed.

Taking down chowkats or frames with shutter, area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (without taking off shutters from frame) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish including removal of serviceable/unserviceable material from site complete all as specified and directed.

Supply and fixing of pressed steel frames for doors of size 105x60mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm MS FI, 25cm long, 6 Nos in each chowkhat, necessary lugs, 3 Nos 100 mm MS butt hinges medium weight, cold rolled, welded for each frame, lock strike plate, including sanding, tarring backs of chowkhats, PCC 1:3:6 type C-0 filling in frame and for holdfast, 2 Nos 12 mm dia tie bars at the bottom of frame and one shop coat of red oxide primer etc complete all as specified and as directed.

Supply and fixing of pressed steel frames for doors of size 125x60mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm MS FI, 25cm long, 6 Nos in each chowkhat, necessary lugs, 3 Nos 100 mm MS butt hinges medium weight, cold rolled, welded for each frame, lock strike plate, including sanding, tarring backs of chowkhats, PCC 1:3:6 type C-0 filling in frame and for holdfast, 2 Nos 12 mm dia tie bars at the bottom of frame and one shop coat of red oxide primer etc complete all as specified and as directed.

Supply and fixing of rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing , cutting, drilling & welding, conforming to Fe-290.Gde-E-165 complete all as specified and as directed.

Supplying and Fixing for Mild steel, plain, black sheet of 1.00mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete all as specified and directed.

Supplying and Fixing for factory made 35mm thick, 2nd class HW, plain framed, panelled shutters (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fixing of solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

Supply and fixing of factory made solid panel PVC moulded door shutter with wood free EPS, 28 to 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, including suppling & fixing in the frame at site as per specification & drawing, with and including 3 Nos. stainless steel butt hinges of 100mm size for fixing the shutter complete all as specified and directed.

Supply and fixing of factory made UPVC white colour Sliding window of area not exceeding 2.00 Sqm each, three track, made of extruded profiles with wall thickness of 2.3mm (+/- 0.2mm). Window profile with hollow section with multi chamber, Frame (88mm x 52mm), sliding sash (42mm x 67mm), sliding mesh sash (42mm x 57mm), Sliding interlock (one vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitered cut and fusion welded at all corners, including railing of holes for fixing of hardware and drainage of wateretc., making arrangement for fixing hardware, EPDM gasket, 1.2 mm +/- 0.2mm thick galvanized steel frame (30mm x18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware (Touch lock of zinc alloyed (white powder coated), steel roller system and required accessories complete all as specified and directed. Note:- The unit rate quoted by the contractor exludes cost of wire cloth and glass and includes all other accessories. Net opening will be measured for payment purpose.

Material and labour for second class hard wood glazed and skeleton shutters, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, elc.;sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as specified and directed.

Supply and fixing of stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Supply and fixing of aluminium anodised, 200mm long, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Supply and fixing of aluminium handles, 150mm, cast type, anodised complete all as specified and as directed.

Supply and fixing of sheet glass, 4.8mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sqm. in each pane complete all as specified and directed.

Supply and fixing of 150mm, mild steel ordinary rat tail rod pattern springs including roller and roller platefixed to wooden chowkhats or welded to angle iron chowkhat frame complete all as specified and directed.

Supply and fixing of towel rail of 20mm dia, D type 60cm long between flanges including bracket 150mm, cast type, anodised complete all as specified and as directed.

Supply and fixing of second class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessaty' labours; articles not exceeding 200 cu.cm each complete all as specified and directed.

Supply and fixing in repair of GI tubing, ISI Marked, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing in repair of GI tubing, ISI Marked, 20mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing in replacement of angular stop valves, 15mm bore, brass chromium plated, ISI marked, with long shank and cup, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Note : Weight of stop valve shall not be less than 0.575 Kg

Supply and fixing in replacement of stop valves, 15mm bore, fancy type, chromium plated, ISI marked, with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Note : Weight of stop valve shall not be less than 0.575 Kg

Supply and fixing in replacement of stop valves, 20mm bore, fancy type, chromium plated, ISI marked, with long shank and cup, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Note : Weight of stop valve shall not be less than 0.575 Kg

Supply and fixing in replacement of bib tap, 15mm bore, fancy type, long body, chromium plated, ISI marked, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule or union and fixed and taking down and removal of existing unserviceable tap of any description and size complete all as specified and as directed. Note : Weight of bib tap shall not be less than 0.575 Kg

Supply and fixing in replacement of 15mm bore brass chromium plated pillar tap, fancy type, chromium plated, cast copper alloy with capstan head, screwed down, high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and taking down and removal of existing unserviceable pillar taps of any description and size complete all as specified and directed.

Supply and fixing in replacement of brass chromium plated shower rose,125mm size, with or without swivel joints, any size. including fixing to steel pipe or union complete all as specified and as directed.

Supply and fixing of PVC connections, 450 mm long and 15mm size with bore fly nuts complete all as specified and directed.

Supply and fixing in repairs, vitreous china squatting pan of Orissa pattern, size 580mmx440mm, white (Ist quality) with ‘P’ or ’S’ trap of PVC, with front or back inlet and integral foot rests of any pattern including provision of lime concrete bedding for fixing and making good to existing floor surface to match with the existing surface and connection to flush pipe, trap, anti syphonage pipe, etc including taking down and removal of existing unserviceable squatting pan of any description and size complete all as specified and directed.

Supply and fixing in repairs of 10 litre capacity, virgin polypropylene cistern, ISI marked, coloured, low level, valveless syohonic action type, 45cm PVC connection with PVC bend/flush pipe complete and making all connections including taking down existing high or low level unserviceable flushing cistern and making good the disturbed surface to match with the existing surface complete all as specified and directed.

Supply and fixing in repair, vitreous china wash hand basin, white colour, flat back, of size 550x440mm, ISI marked, with 2 Nos.CI brackets embedded in cement mortar 1:4, PVC waste pipe, 45cms long, fixed to walls, 15mm dia PVC connections and chromium plated waste coupling, etc.,including taking down/removal of existing unserviceable wash hand basin of any description and size and making good the disturbed surfaces to match with existing surfaces complete all as specified and directed.

Supply and fixing of water storage tank of 500 ltr capacity, HDPE triple layer, cylindrical, vertical with closed top and FDA approved, 100% UA stabilized, rust proof, ISI marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, ISI marked, screwed and suitable for iron pipe 20 mm bore including taking down of old tank of any descrption and removal from site complete all as specified and directed. Note:- Tank shall be white and make of tank shall be engraved on the tank.

Supply and fixing mild steel powder coated decorative curtain rod, 20mm dia, fixed with decorative brackets, stop roller and funnels at the end for each cut length complete all as specified and directed.

Supply and fixing of PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement setting and jointing to drain pipes with cement mortar (1 :1) including demolition of old unserviceable gully trap complete all as specified and as directed.

Material and labour for mild steel TMT bars, Fe-500/550D, 8 mm dia and over upto and including 10mm dia as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour for mild steel TMT bars, Fe-500/550D, 6 to 8 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Supply and fixing in replacement mild steel almirah shutters with frame, exceeding 1.5 Square metre, made of 1mm thick mild steel sheet, in two leaves, as built in furniture in cupboards, including locking arrangement with mortice lock of mild steel, vertical type, 65mm size, 2 lever, ISI marked with duplicate keys and handle, etc. (all as per Godrej pattern) including two coats of approved colour synthetic enamel spray painting over a coat of red oxide primer complete fixed in brick or concrete wall with minimum six numbers of 10mm dia and 100mm long mild steel bolt with washer and nut in cement mortar (1:4) or PCC 1:2:4, type B-0, complete all as specified and directed.

Material and labour for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of approved colour synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and labour for preparation of new steel surfaces, of any description not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint, over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Material and labour for preparation of new steel surfaces, of any description not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint, complete all as specified and as directed.

Material and labour for preparation of old steel surfaces, of any description not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint, complete all as specified and as directed.

Material and labour for Roof/slab treatment with following steps of works: (i) Cleaning the roof surface to remove any loose/ unsound material, dirt, dust etc. with mechanical means i.e. wire brush/ air blower etc. and removal of debries from site to distance exceeding 250mtrs. (ii) Applying a bonding coat of SBR latex based polymer Dr. Fixit UPR confirming to ASTM C 190-85/881 and cement in ratio (1:1.5) @4.0 Sqm/Kg/Coat along the junction of parapet walls and sloped RCC roof and making of coving/gola with cement sand mortar (1:3) admixed with liquid integral water proofing compound Dr. Fixit LW confirming to IS: 2645-1983 @200ml/50Kg bag of cement mix. (iii) Applying one primer coat of acrylic based polymer Dr. Fixit new coat confirming to ASMT C-836/1202, ASMT D-2240/412/4541, ASMT E-96, ASMT G-154 and water in (1:1) ratio @ 4.0 Sqm/Kg/Coat with roller or paint brush on RCC roof surface and allow it to dry. The primer shall be carried upto full height at parapet walls/ upto 1mtr height at side walls. (iv) Applying second coat of acrylic based polymer Dr. Fixit new coat confirming to ASMT C-836/1202, ASMT D-2240/412/4541, ASMT E-96, ASMT G-154 @2.0Sqm/Kg/Coat with roller or paint brush on RCC roof surface and allow to dry. (v) Applying third and final coat of acrylic based polymer Dr. Fixit new coat confirming to ASMT C-836/1202, ASMT D-2240/412/4541, ASMT E-96, ASMT G-154 @2.0Sqm/Kg/Coat with roller or paint brush on RCC roof surface and allow to dry. Note: The work shall be carried out by the authorised manufacturer rap. The contractor shall also submit the security deposit and guarntee for roof treatment as specified.

Material and labour for preperation of newly plastered surfaces of walls, chajjas, roof projection, cornices etc. and applying using roller two coats of oil bound distemper over 1-2mm thick wall care putty complete all as specified and as directed.

Material and labour for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and as directed.

Material and labour for preparation of old plastered ceiling surfaces and applying two coats of white wash complete all as specified and as directed.

Material and labour for preperation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and as directed.

Supply and fixing in replacement stainless steel plate rack 1mm thick of grade SS 304 of size 750 x 600 x 200mm weighing not less than 8 Kg each fixed with stainless steel screw to wall, complete all as specified and directed.

Supply and fixing in replacement, stainless steel sink with draining board, made out of 1mm thick sheet of grade SS 304, for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mmx330mmx160mm including waste pipe and waste fittings, brass, chromium plated for glazed ware sinks, basins etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

Material and labour for premium quality, glazed white ceramic tiles of size 150 x 75 x 6-7mm thick in repairs on vertical surfaces of walls over and including 10mm thick rough finished plaster in cement mortar (1:4), set, jointed in neat cement slurry and pointed in white or coloured cement to match including printed black bldg No. on tile complete all as specified and directed.

Supply and fixing in repairs, 110mm dia PVC soil, waste, drain pipe, type ‘B’, conforming to IS 13592-1992, single socketed, in any length, with rubber rings joints or jointed with solvent cement, fixed to walls with clamps including taking down of old pipe as existing at site complete all as specified and as directed. Note- Rubber rings for pipes and fittings shall conform to IS 5382-1985.

Supply and fixing of PVC (SWR) bends/shoes,110mm bore, of any radius including jointing with solvent cement complete all as specified and directed.

Dismantling of brick tiles or terracing tiles single layer on roof and removal of debries to distance exc 250 mtr but n exc 500 mtr complete all as specified and as directed.

Demolition of mud in roofs any thickness including plastering and leeping plaster any thickness and removal of debries to distance exc 250 mtr but n exc 500 mtr complete all as specified and as directed.

Material and labour for providing cement concrete 1:2:4, type B1, using 20mm graded aggregates, as in roof kerbs or mud stops, padding, rounded or chamfered on edges as in roof, finish even and fine using WPC complete all as specified and as directed. Note : Supply only WPC shall be measured and paid separately.

Material and labour in replacement for 18mm thick prelaminated particle board, exterior grade (grade-I), conforming to IS-14587, fixed with screws/glue, as in kitchen cupboards, cabinets, shelf for cupboard complete all as specified and directed.

Supply and fixing of continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flaps when open 30mm complete all as specified and directed.

Material and labour for PCC (1:4:8) type D2 (using 40mm graded stone aggregates), 75 mm thick, as in sub base of floors, finished rough and even to receive floor topping complete all as specified and as directed.

Material and labour, for vibratory compacted, precast cement concrete rubber moulded, coloured (except grey colour), interlocking designer paver blocks in milano shape, confirming to IS-15658-2006 of 60mm thickness, M-35 grade, as in path, hard standing, etc. laid over and including 25mm thick rammed bedding layer of sand, complete all as specified and directed.

Supply and fixing of mild steel, cold rolled, butt hinges, 100mm size, medium weight, ISI marked and fixed complete all as specified and as directed.

Supply and fixing of 300mm size aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Material and labour for preperation of old plastered or previousely treated surfaces of walls and applying two coats of exterior acrylic emulsion paint of shade as directed complete all as specified and as directed.

Supply and fixing of aluminium handles, 75mm, cast type, anodised complete all as specified and as directed.

Supply and fixing of magnetic catcher suitable for wooden cabinet fixed with steel screws complete all as specified and as directed.

Material and labour for 40mm thick brick tiles laid on 15mm thick bed in cement mortar (1:3) and jointed and pointed in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on mud phuska complete all as specified and as directed.

All as above Item No 92.00 but except bricks complete all as specified and as directed.Note: Old serviceable bricks as obtained from serial item No 80.00 hereinbefore shall be reused after cleaning the bricks. The rate quoted shall include for cleaning the bricks also.

SCHEDULE A PART II (E/M WORKS) Taking down carefully any type of point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, regulators, sockets, tube light fittings with all accessories etc., and/or drawing out from existing conduit/batten and removal of materials from site and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces with matching OBD/White wash/Distemper complete all as specified and as directed.

Material and labour for concealed point wiring using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area), single core, FRLS-H, 1100 volts, ISI marked, PVC insulated and unsheathed stranded cable drawn through and including non metallic, medium grade PVC concealed conduit not less than 25.00mm to 32.00mm dia and its fittings, including cutting chasing on wall/ceiling, including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes, ISI marked, including 1.5 sqmm single core PVC insulated and unsheathed FRLS-H cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dolly with and including MS flush boxes of 2 to 18 modules with inner and outer cover plates, confirming to IS 5139 of 1969 and IS 14772 of 2000 for fixing modular switch sockets for one light point (For flourescent Tube/ LH, Bldg Security light, Mirror light)/fan point/bell point controlled by one one way switch complete all as specified and as directed. Notes :- (i) Switch, socket, ceiling rose, lamp holder, bell, bell push and fan regulators to be measured and paid for separately. The quoted rates are deemed to be included for providing cover plates and MS flush boxes as required at site. (ii) PVC Conduit conforming to IS 9537 part I & III. (iii) All chases will be cut by chase cutter only and surfaces shall be make good as per existing surfaces. (iv) The concealed conduits and MS boxes as fixed against new point wiring, shall be verified by Engineer-in-Charge before making good the surfaces by plastering and other finishes.

Description all as per Srl item No.95.00 here in before but for one 3 pin socket outlet point 5 Amp on Independent board.

Description all as per serial item No.95.00 above, but for one metal clad box point (independent) power point, with 4 Sqmm PVC, FRLS-H, unsheathed, multistranded cable, 1100 volts grade, ISI marked, including 4 Sq mm size, green colour, PVC insulated FRLS-H, continuous copper earth wire and connected to common earth dolly complete all as specified and as directed.

Supply and fixing of switch modular, 6 Amps, one way, one module, flush type, single pole, 230 volt, ISI marked complete all as specified and directed.

Supply and fixing of switch modular, 16 Amps, one way, two module, single pole, 230 volts, ISI marked complete all as specified and directed.

Supply and fixing of socket modular, 2/3 pin, 5/6 amps, one way, two module, single pole, 230 volts complete all as specified and directed.

Supply and fixing of socket outlet, modular, 2/3 pin, 6/16 Amps, one way, two module, single pole, 230 volts, ISI marked complete all as specified and directed.

Supply and fixing of fan regulator, modular, 120 watt, two module, 230 volts, 50 Hz, AC supply, suitable for ceiling fan any type/make/sweep complete all as specified and as directed.

Supply and fixing of ceiling rose, surface bakelite, 65x50mm, three terminals along with back plates complete all as specified and as directed.

Supply and fixing of bell push, modular type, 6 Amps, 230 Volts, one module complete all as specified and as directed.

Supply and fixing of electric bell buzzer, ding dong type, AC, 230 volts, single pole complete all as specified and as directed.

Supply and fixing of lamp holder, PVC/Polycarbonate type, with back plate suitable for batten fittings complete all as specified and as directed.

Supply and fixing in replacement of retrofit LED Bulb of 9 watt suitable for batten holder B-22 complete all as specified and directed.

Supply and fixing of MCB SP, 6 to 32 Amps, 240 volt, 10 KA, 'C' curve, ISI marked, connected with suitable lugs and testing complete all as specified and directed.

Supply and fixing of RCBO, 40 Amps, double pole, conforming to IEC-61009, 2 module, 300 ma (HI immunity) sensitivity, 230 volts, 50 Hz, with degree of protection IP-20, for three protection, over load prtection, earth leakage protection, and short circuit protection, ISI marked complete all as specified and directed.

Supply and fixing in replacement of over voltage release, one module, 230 volts, single phase, adjustable from 170 volts to 230 volts in one module suitable for (1Ph+N) complete all as specified and directed.

Supply, insatallation, commissioning and testing of distibution board for MCBs, SPN, 8 way, acrylic double door, IP 43, as per IS 8623, 240 volts, with and including 200 amps fully insulated copper bus bar fixed on wall duly grouted in solid block wall with and including copper lugs/thimbles duly crimped for connection including taking down and removal of old unserviceable DB with MCB of any capacity, size and type complete all as specified and directed. Note :- MCB shall be measured and paid separetely.

Supply and fixing of sheet metal enclosures vertical load line TPN distribution board, 4 ways, double door powder coated alongwith 200 Amp rated busbar with and including MCCB 4 pole 100 Amp adjustable type as incomer with suitable size of MS cabinet fabricated by 2mm thick MS sheet and making all type of connections using proper size of gland for incomer cable complete loadline TPN concealed on wall surface & making good the disturbed surfaces as per existing and dismantling and taking down the existing DB's of any type complete all as specified and as directed.

Material and labour for sub main wiring with two single core, 6 sqmm, FRLS-H, 1100 volts grade, ISI marked, with multistranded, PVC insulated unsheathed copper conductor cable, drawn in and including rigid non metallic PVC conduit, medium grade, not less than 25 mm dia, ISI marked for housing cables, concealed in wall or ceiling including necessary cutting, chasing with machine and making good disturbed surfaces as per existing, with accessories with and including one additional 6 sqmm, PVC insulated, stranded copper conductor, FRLS-H, green colour for earth continuity conductor connected to common earth dolly including taking down old unserviceable sub main wiring of any type and making good the disturbed surface complete all as specified and as directed. Note- Three runs of cable and one run of concealed conduct shall be measured as one unit.

Supply and fixing in replacement channel for fixing of LED tube rod, made of aluminium housing body in CRCA sheet, suitable for 18/20 watt LED tube light, high efficient, AC, 220-240 Volts, 50 Hz, with built in electronic drivers having THD < 10%, connecting up with core 1.5 sq mm flexible copper conductor cable from ceiling rose to connector block of light fitting including T-5 LED tube rod 1x18/20 watts, AC, 220-240 Volts, 50 Hz, high efficient T8 with aluminium extrusion heat sink for optimum performance with high lumen efficiencydisconnecting and taking down existing light fitting and removal complete all as specified and directed.

Supply and fixing of decorative, surface mounted, LED mirror light, wall mounting light fitting, high efficient PMMA diffuser, aluminium housing in CRCA body suitable for and including 10 watt LED tube, high efficient, AC 220-240 volts,50 Hz, and compact and energy efficient, epoxy powder coated, CRCA sheet, connecting with copper conductor flexible cable of size 0.50 Sqmm from ceiling rose to connector of the light fitting including disconnecting and taking down of existing old unserviceable light fitting of any description and removal from site complete all as specified and directed.

Supply and fixing in replacement of LED security light luminaire 45 watt, 230 volts, 50 Hz, made up of die cast aluminum housing with black epoxy powder coating with cover heat resistant glass, safety input voltage range 170 to 270 Volts, IP66 protection, including service brackets of GI pipe 25mm bore, light grade, of length 0.90 metre, bent to required shape, fixed with MS clamps of size 40 x 6mm flat iron strip, 150mm long and 4 Nos.8mm dia stainless steel bolts and nuts and washers and suitable reducer for connecting to GI pipe as required at site and making all required electrical connections using 3 core copper flexible cable from terminal box to ceiling rose including disconnecting and taking down of old fitting with bracket as existing complete all as specified and as directed.

Supply and laying of LT underground cable, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty), 1100 volts grade, with stranded aluminium conductor of size 3.5 core, 25 Sqmm and laying in trenches including disconnecting and taking down of old unserviceable existing cable and removal complete all as specified and as directed. Note:- Excavation and earth work shall be measured and paid separetely.

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth and getting out in soft/loose soil for laying of cable complete all as specified and as directed.

Returning filling in, in soil, including spreading leveling watering and well ramming in layers not exceeding 25 cm each complete all as specified and as directed.

Removing excavated spoil/materials to a distance not exceeding 50 metre and depositing where directed at level not exceeding 1.5 above the starting point complete all as specified and as directed.

Material and labour for Sand cushioning to cable with a layer of sand 8 cm deep before laying the cable and 15 cms deep after laying the cable (punned down to 18 cms depth after laying and stretching of cable ) complete all as specified and as directed.Note:- Punned thickness 18cm shall be measured for payment purposes.

Supply and laying un-reinforced, precast concrete cable cover, class LV type 1, flat, with peak, size 250 mm x150 mm x40 mm complete all as specified and as directed.

Supply and fixing in replacement of light grade, GI tubing, of size 40mm dia, for cable protection and fixed with clamp to pole and wall with nuts and bolts complete all as specified and as directed.

Disconnecting/dismantling old unserviceable earthing and material and labour for new earthing with galvanised earth plate electrode 600mm x 600mmx 6mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m below ground level with top edge of the earth plate not less than 1.5m below normal ground level, connected to 4.00 mm GI wire earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire and thimbles protected by galvanized steel pipe 15mm dia (light grade) and connected to main switch or main control board all as shown in Electrical Plate No.3 of SSR Part-I & including necessary excavation and earth work in any type of strata, PCC (1:3:6) type C1 in pit, RCC cover slab 50mm thick in 1:2:4 type B-1 using 8mm dia TMT bars @10cm c/c both way with one 8mm dia bar as handle for lifting, 20mm dia GI medium grade watering pipe, funnel, wire wesh, charcoal or coke & salt in alternate layers, etc.all as indicated including testing on completion complete all as specified and directed. Note:- The new earthing shall be provided adjecent to old earthing site on the locations as directed by engineer in charge.

Taking down fan any type/description, after disconnecting all electrical connections carefully, sealing cable end, dismantling blades and removing fan and material and labour for scrapping old paint, cleaning dust and washing with washing powder, filling cavities with filler, spray painting complete fan with two coats of synthetic super enamel paint, writing MES No with black colour permanent marker and hanging the fan at the existing or new location and making all electrical connections using 3 core copper flexible cable drawn through flexible PVC conduit pipe and testing complete all as specified and directed.

Note:- Amount of credit of Rs. 72,370.00 for retrieved materials is mentioned in Schedule of Credit Page Nos. 18R & 19R of tender documents in pdf form which will be deducted offline while acceptance of tender.

Swami Enterprises

Bhagwan Dass and Sons

Ashwani Kumar

MAYANK ENTERPRISES

Karishan Kumar goel

bhagwandasswazirchand

SMT Construction