Combined various electrical works at physics dept, geo tech lab, and residential campus

Amount

PANEL BOARD

MCCB, MCB & DB'S

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MOB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MOB TPDB is normally used where 3 phase outlets are required.)

4 way (8 + 12), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MOB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, 415 V, 'C' curve miniature circuit breaker suitable for inductive load of Four Pole in the existing MCB DB, complete with connections, testing and commissioning etc. as required.

MV CABLE JOINTING & END TERMINATION

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

4 X 10 sq. mm (25mm)

4 X 16 sq. mm (28mm)

4 X 25 sq. mm (28mm)

4 X 35 sq. mm (32mm)

Supplying and making straight through joint with heat shrinkable kit including ferrules and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

4 X 16 sq. mm

4 X 25 sq. mm

4 X 35 sq. mm

LT CABLE

Supplying of following size Aluminium conductor XLPE insulated PVC sheathed power cable of 1.1 kV grade etc. as required.

4C x 10 Sq.mm

4C x 16 Sq.mm

4C x 25 Sq.mm

4C X 35 Sq.mm

PANEL BOARD

Charges for cleaning and spray painting the existing Panel board of following size or nearest size with two coats of suitable colour (Grey) paint, over a coat of primer in installed position and marking the identification of switches with white paint etc, as required ( Site visit recommended).

Fabrication & fixing of panel board Sheet made from 14 gauge thick galvano sheet, powder coated in suitable colour over a coat of primer, providing rubber beadings and suitable size hinches, Nuts & Bolts for fixing on the existing panel board etc. as required( Site visit recommended)..

Fabrication & fixing of Sheet made from 16 gauge thick Galvano sheet, powder coated in suitable colour over a coat of primer, Nuts & Bolts for fixing or welding on the base or roof of the existing panel board etc. as required( Site visit recommended)..

Supply and fixing of black coloured, 8mm width, Rubber beading of suitable size for panel door etc as required.

Fabrication ,Design and Installation of the following dust,weather and vermin proof outdoor type floor mounted panel with hinged door confirming to IS and IE rules made out of 14 gauge galvano sheet and duly powder coated with provisions for fixing 3 phase vertical 4 way double doorDB along with proper connectors and cable end terminations and provision for cable entry along with necessary civil work if required. ( Site visit recommended).

Fabrication , Design and installation of the following dust,weather and vermin proof outdoor type floor mounted panel with hinged door confirming to IS and IE rules made out of 14 gauge galvano sheet and duly powder coated with provisions for fixing 1 phase horizontal 4 way DB along with proper connectors and cable end terminationsand provision for cable entry and necessary civil work if required. ( Site visit recommended).

Fabrication,Design and installation of the following dust,weather and vermin proof outdoor type floor mounted panel confirming to IS and IE rules made out of 14 gauge galvano sheet and duly powder coated with provisions for fixing 1 phase horizontal 16 way DB along with proper connectors and cable end terminations and provision for cable entry and necessary civil work if required. ( Site visit recommended).

BSED AC POINTS

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

3 x 4 sq. mm

3 x 2.5 sq. mm

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MOB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MOB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MOB TPDB is normally used where 3 phase outlets are required.)

8 way (4 + 24), Double door

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

Supplying and fixing 20/25 A modular DP switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 3 pin 25 A modular socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 63 amps rating, four pole, 415 Volts, 'C' curve miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connectons, testing and commissioning etc as required.

Supplying and fixing 63A , Triple pole, 430 V, C curve Miniature circuit breaker (MCB) in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and making end termination of PVC insulated copper conductor 4x16+ 2x6 sqmm submain wiring with suitable size Copper lugs including connection etc as required.

Removal of existing 3 Phase, 4 way MCCB DB, making good the damges of the wall/floor including cement,sand, paint and other accessories without any damages and conveyance of the materials to the godown etc as required.

Supplying and fixing 3 phase 8 way , double door, suface/recess mounting, vertical type, 415 V, TPN distribution board with provision for fixing MCCB as incomer and TP MCB as out going, complete with 200 A tinned copper bus bar, common neutral link, earth link, din bar for mounting MCBs, detachable gland plate, interconnections, earthing, phosphatized and powder painted, fixing using bolt and nut, giving connections etc. as required. (But without MCCB, MCB)

Supplying and fixing 125A, 16kA, 4 pole MCCB(Thermal magnetic O/L & S/C protection), 415 V, Moulded casing circuit breaker (MCCB) in the existing MCCB DB , complete with connections, testing and commissioning etc, as required.

Supplying and fixing the identification details of cables and Distribution boards details with vinyl stickers on existing 4 nos of DB etc. as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3.5 C X 70 sq. mm (38mm)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing extra down rod of 10 cm length G.I. pipe ,15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Installation, testing and commissioning of pre-wired, LED Light fitting of all types, complete with all accessories and tube/lamp etc., including supplying and fixing ball and socket arrangement, 2 Nos. down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

FAN HOOK

Supplying and fixing of 8/10 mm "S" type steel fan hook including chipping,welding, painting making good the damages etc. as required

Supply Installation Testing and Commissioning of 28W 1200 mm sweep 5 Star rated BLDC ceiling fan with input voltage range (140-285V), 380 rpm, Air delivery 235 m3/min, regulator supported type, Aluminium Blade material ,white colour,with 3 years onsite warranty, conforming to IS:374:2019 latest including, required length, painted down rod (GI) providing and fixing Suitable type fan hooks including connections,welding etc. as required.

LED TUBELIGHT

Supply of box type tube fittings (Batten ) compatible for fixing 2 T8 LED tube light, complete with side holders etc, as required.(Batten- IGP162LT8-16 2XT8 or compatible)

Supply of 18/20 watt 4 feet T8 LED tube with efficacy 100lm/W. (T8 LED-Crompton LGT8-20-865-2 or compatible)

PHYSICS 012

Supplying and fixing of 20 mm (medium class) ivory coloured rigid PVC conduit along with accessories in surface / recess including cutting the wall / floor and making good the same in case of recessed conduit as required.

Supplying and fixing of 25 mm (medium class) ivory coloured rigid PVC conduit along with accessories in surface / recess including cutting the wall / floor and making good the same in case of recessed conduit as required.

Supplying and drawing 3 numbers 2.5 sq.mm FRLS PVC insulated copper conductor single core cable (Red, Black & Green) in the existing surface/recessed PVC conduit as required.

Supplying and drawing 3 numbers 4 sq.mm FRLS PVC insulated copper conductor single core cable (Red, Black & Green) in the existing surface/recessed medium class PVC conduit as required.

Supplying and fixing 5/6 A modular switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 15/16 A modular switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 3 pin 5/6 A modular socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 6 pin 15/16 A modular socket (3 module) outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 3 Module, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

Supplying and fixing 8 Module, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

Supplying and fixing 6 Module, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate etc. as required.

Supplying and fixing 20/25 A modular DP switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 3 pin 25 A modular socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 1/2 module, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

Supplying and fixing 6 - 32 amps rating, 240 Volts, 'C' curve miniature circuit breaker suitable for inductive load of single pole in the existing MCB DB complete with connectons, testing and commissioning etc as required.

Charges for removing metal enclosures, old Distribution board with MCB, RCCB, & other accessories without any damage and making good the damages of the wall including painting, etc. as required.

Removing of switch board of any size including wires, switches(modular/piano type) switch board, ,fan regulators,clamps, GI/plastic box etc. as required and handing over to the store/yard.

Removing of conduits, wires, clamps etc. as required and handing over to the store/yard.

GEOTECH LAB

Supplying and drawing 3 x 2.5 sq. mm of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of 20 mm of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of 25 mm of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular switch socket outlet and 15/16A modular switch , connections etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Single pole in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 63A rating, Four pole, (Three phase and neutral), 415 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing single pole blanking plate in the existing MCB SB complete etc.as required.)

Supplying and fixing 3 phase 8 way(4+24) , double door, vertical type three pole and neutral ,sheet steel,MCB distribution board,415 V on suface/recess mounting, complete with 200 A tinned copper bus bar, common neutral link, earth link, din bar for mounting MCBs, detachable gland plate, interconnections, earthing, phosphatized and powder painted, fixing using bolt and nut, giving connections etc. as required. (But without MCCB, MCB etc)

Supplying and fixing 63 A rating, 415 V, 10kA, "C" curve miniature circuit breaker suitable for inductive load of four pole in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Charges for removing the old wall mounted DB's, making good the damages of the wall/ floor including painting, dismantle the DB and other accessories without any damage and conveyance of the material to the godown etc, as required.

Supplying, installing, testing and commissioning of 63A TPN capacity TPN tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with TPN disconnector FSU and HRC fuses, connections, earthing etc. as required.

Removing of Conduit including conduit, wires, clamps etc. as required and handing over to the store/yard.

SL ELECTRICAL WORKS (BID ID -3320450)

DIAMOND ENGINEERING WORKS (BID ID -3320300)

NATIONAL ENGINEERING COMPANY (BID ID -3320090)